Before changing dccp_v6_request_recv_sock() sock argument
to const, we need to get rid of security_sk_classify_flow(),
and it seems doable by reusing inet6_csk_route_req() helper.
We need to add a proto parameter to inet6_csk_route_req(),
not assume it is TCP.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factorize code to get tcp header from skb. It makes no sense
to duplicate code in callers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we realize tcp_rcv_synsent_state_process() does not use
its 'len' argument and we get rid of it, then it becomes clear
this argument is no longer used in tcp_rcv_state_process()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these functions need to change the socket, make it
const.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier patch 6ae459bda tried to detect void ckecksum partial
skb by comparing pull length to checksum offset. But it does
not work for all cases since checksum-offset depends on
updates to skb->data.
Following patch fixes it by validating checksum start offset
after skb-data pointer is updated. Negative value of checksum
offset start means there is no need to checksum.
Fixes: 6ae459bda ("skbuff: Fix skb checksum flag on skb pull")
Reported-by: Andrew Vagin <avagin@odin.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
Minor IPv4 routing cleanups
These patches just contain some minor cleanups to address a few minor
issues. The first and the third mostly just improve readability. The
second patch should improve the performance for multicast destination
addresses that do not have a localhost source IP address by avoiding some
unnecessary dereferences.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
err is initialized to -EINVAL when it is declared. It is not reset until
fib_lookup which is well after the 3 users of the martian_source jump. So
resetting err to -EINVAL at martian_source label is not needed.
Removing that line obviates the need for the martian_source_keep_err label
so delete it.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just swaps the ordering of one of the conditional tests in
ip_route_input_mc. Specifically it swaps the testing for the source
address to see if it is loopback, and the test to see if we allow a
loopback source address.
The reason for swapping these two tests is because it is much faster to
test if an address is loopback than it is to dereference several pointers
to get at the net structure to see if the use of loopback is allowed.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates ip_check_mc_rcu so that protocol is passed as a u8
instead of a u16.
The motivation is just to avoid any unneeded type transitions since some
systems will require an instruction to zero extend a u8 field to a u16.
Also it makes it a bit more readable as to the fact that protocol is a u8
so there are no byte ordering changes needed to pass it.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wolfgang reported that IPv6 stack is ignoring oif in output route lookups:
With ipv6, ip -6 route get always returns the specific route.
$ ip -6 r
2001:db8:e2::1 dev enp2s0 proto kernel metric 256
2001:db8:e2::/64 dev enp2s0 metric 1024
2001:db8:e3::1 dev enp3s0 proto kernel metric 256
2001:db8:e3::/64 dev enp3s0 metric 1024
fe80::/64 dev enp3s0 proto kernel metric 256
default via 2001:db8:e3::255 dev enp3s0 metric 1024
$ ip -6 r get 2001:db8:e2::100
2001:db8:e2::100 from :: dev enp2s0 src 2001:db8:e3::1 metric 0
cache
$ ip -6 r get 2001:db8:e2::100 oif enp3s0
2001:db8:e2::100 from :: dev enp2s0 src 2001:db8:e3::1 metric 0
cache
The stack does consider the oif but a mismatch in rt6_device_match is not
considered fatal because RT6_LOOKUP_F_IFACE is not set in the flags.
Cc: Wolfgang Nothdurft <netdev@linux-dude.de>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some embedded systems the EEPROM does not contain a valid MAC address.
In that case it is better to fallback to a generated mac address and
let init scripts fix the value later.
Reported-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
[Changed handcoded setup to use eth_hw_addr_random() and to save new address into HW]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason we were carrying the budget value around between the
various calls to napi->poll. If for example one of the drivers called had
a bug in which it returned a non-zero value for work this could result in
the budget value becoming negative.
Rather than carry around a value of budget that is 0 or less we can instead
just loop through and pass 0 to each napi->poll call. If any driver
returns a value for work done that is non-zero then we can report that
driver and continue rather than allowing a bad actor to make the budget
value negative and pass that negative value to napi->poll.
Note, the only actual change here is that instead of letting budget become
negative we are keeping it at 0 regardless of the value returned for work
since it should not be possible for the polling routine to do any actual
work with a budget of 0. So if the polling routine returns a non-0 value
we are just reporting it and continuing with a budget of 0 rather than
letting that work value be subtracted from the budget of 0.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise 4294967295 (MBit/s) (-1) will be printed when there is no link.
Documentation/ABI/testing/sysfs-class-net does not state if this shall be
signed or unsigned.
Also remove the now unused variable fmt_udec.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several functions can return negative value in case of error,
so their return type should be fixed as well as type of variables
to which this value is assigned.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaron Conole says:
====================
af_unix: return data from multiple SKBs on recv() with MSG_PEEK flag
This patch set implements a bugfix for kernel.org bugzilla #12323, allowing
MSG_PEEK to return all queued data on the unix domain socket, not just the
data contained in a single SKB.
This is the v3 version of this patch, which includes a suggested modification
by Eric Dumazet to convert the unix_sk() conversion macro to a static inline
function. These patches are independent and can be applied separately.
This set was tested over a 24-hour period, utilizing a loop continually
executing the bugzilla issue attached python code. It was instrumented with
a pr_err_once() ([ 13.798683] unix: went there at least one time).
v2->v3:
- Added Eric Dumazet's suggestion for #define to static inline
- Fixed an issue calling unix_state_lock() with an invalid argument
v3->v4:
- Eliminated an XXX comment
- Changed from goto unlock to explicit unix_state_unlock() and break
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
AF_UNIX sockets now return multiple skbs from recv() when MSG_PEEK flag
is set.
This is referenced in kernel bugzilla #12323 @
https://bugzilla.kernel.org/show_bug.cgi?id=12323
As described both in the BZ and lkml thread @
http://lkml.org/lkml/2008/1/8/444 calling recv() with MSG_PEEK on an
AF_UNIX socket only reads a single skb, where the desired effect is
to return as much skb data has been queued, until hitting the recv
buffer size (whichever comes first).
The modified MSG_PEEK path will now move to the next skb in the tree
and jump to the again: label, rather than following the natural loop
structure. This requires duplicating some of the loop head actions.
This was tested using the python socketpair python code attached to
the bugzilla issue.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Eric Dumazet this change replaces the
#define with a static inline function to enjoy
complaints by the compiler when misusing the API.
Signed-off-by: Aaron Conole <aconole@bytheb.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the bridge vlan implementation to use rhashtables
instead of bitmaps. The main motivation behind this change is that we
need extensible per-vlan structures (both per-port and global) so more
advanced features can be introduced and the vlan support can be
extended. I've tried to break this up but the moment net_port_vlans is
changed and the whole API goes away, thus this is a larger patch.
A few short goals of this patch are:
- Extensible per-vlan structs stored in rhashtables and a sorted list
- Keep user-visible behaviour (compressed vlans etc)
- Keep fastpath ingress/egress logic the same (optimizations to come
later)
Here's a brief list of some of the new features we'd like to introduce:
- per-vlan counters
- vlan ingress/egress mapping
- per-vlan igmp configuration
- vlan priorities
- avoid fdb entries replication (e.g. local fdb scaling issues)
The structure is kept single for both global and per-port entries so to
avoid code duplication where possible and also because we'll soon introduce
"port0 / aka bridge as port" which should simplify things further
(thanks to Vlad for the suggestion!).
Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port
rhashtable, if an entry is added to a port it'll get a pointer to its
global context so it can be quickly accessed later. There's also a
sorted vlan list which is used for stable walks and some user-visible
behaviour such as the vlan ranges, also for error paths.
VLANs are stored in a "vlan group" which currently contains the
rhashtable, sorted vlan list and the number of "real" vlan entries.
A good side-effect of this change is that it resembles how hw keeps
per-vlan data.
One important note after this change is that if a VLAN is being looked up
in the bridge's rhashtable for filtering purposes (or to check if it's an
existing usable entry, not just a global context) then the new helper
br_vlan_should_use() needs to be used if the vlan is found. In case the
lookup is done only with a port's vlan group, then this check can be
skipped.
Things tested so far:
- basic vlan ingress/egress
- pvids
- untagged vlans
- undef CONFIG_BRIDGE_VLAN_FILTERING
- adding/deleting vlans in different scenarios (with/without global ctx,
while transmitting traffic, in ranges etc)
- loading/removing the module while having/adding/deleting vlans
- extracting bridge vlan information (user ABI), compressed requests
- adding/deleting fdbs on vlans
- bridge mac change, promisc mode
- default pvid change
- kmemleak ON during the whole time
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT says:
====================
net: mvneta: Switch to per-CPU irq and make rxq_def useful
As stated in the first version: "this patchset reworks the Marvell
neta driver in order to really support its per-CPU interrupts, instead
of faking them as SPI, and allow the use of any RX queue instead of
the hardcoded RX queue 0 that we have currently."
Following the review which has been done, Maxime started adding the
CPU hotplug support. I continued his work a few weeks ago and here is
the result.
Since the 1st version the main change is this CPU hotplug support, in
order to validate it I powered up and down the CPUs while performing
iperf. I ran the tests during hours: the kernel didn't crash and the
network interfaces were still usable. Of course it impacted the
performance, but continuously power down and up the CPUs is not
something we usually do.
I also reorganized the series, the 3 first patches should go through
the irq subsystem, whereas the 4 others should go to the network
subsystem.
However, there is a runtime dependency between the two parts. Patch 5
depend on the patch 3 to be able to use the percpu irq.
Thanks,
Gregory
PS: Thanks to Willy who gave me some pointers on how to deal with the
NAPI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the switch to per-CPU interrupts, we lost the ability to set which
CPU was going to receive our RX interrupt, which was now only the CPU on
which the mvneta_open function was run.
We can now assign our queues to their respective CPUs, and make sure only
this CPU is going to handle our traffic.
This also paves the road to be able to change that at runtime, and later on
to support RSS.
[gregory.clement@free-electrons.com]: hardened the CPU hotplug support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver allows to change the default RX queue trough the rxq_def
kernel parameter.
However, the current code doesn't allow to have any value but 0. It is
actively checked for in the driver's probe because the drivers makes a
number of assumption and takes a number of shortcuts in order to just use
that RX queue.
Remove these limitations in order to be able to specify any available
queue.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that our interrupt controller is allowing us to use per-CPU interrupts,
actually use it in the mvneta driver.
This involves obviously reworking the driver to have a CPU-local NAPI
structure, and report for incoming packet using that structure.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU_MAP register is duplicated for each CPUs at different addresses,
each instance being at a different address.
However, the code so far was using CONFIG_NR_CPUS to initialise the CPU_MAP
registers for each registers, while the SoCs embed at most 4 CPUs.
This is especially an issue with multi_v7_defconfig, where CONFIG_NR_CPUS
is currently set to 16, resulting in writes to registers that are not
CPU_MAP.
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPIC driver currently has a list of interrupts to handle as per-cpu.
Since the timer, fabric and neta interrupts were the only per-cpu
interrupts in the system, we can now remove the switch and just check for
the hardware irq number to determine whether a given interrupt is per-cpu
or not.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers might use the per-cpu interrupts and still might be built as a
module. Export request_percpu_irq an free_percpu_irq to these user, which
also make it consistent with enable/disable_percpu_irq that were exported.
Reported-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation of request_percpu_irq is confusing and suggest that the
interrupt is not enabled at all, while it is actually enabled on the local
CPU.
Clarify that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network namespace is easiliy available in state->net so use it.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Don't make ip6_route_me_harder guess which network namespace
it is routing in, pass the network namespace in.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Don't make ip_route_me_harder guess which network namespace
it is routing in, pass the network namespace in.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ip6t_SYNPROXY already does this and this is needed so that we have a
struct net that can be passed down into ip_route_me_harder, so
that ip_route_me_harder can stop guessing it's context.
Along the way pass snet into synproxy_send_client_synack as this
is the only caller of synprox_send_tcp that is not passed snet
already.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The network namespace is needed when routing a packet.
Stop making nf_afinfo.reroute guess which network namespace
is the proper namespace to route the packet in.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is needed so struct net can be pushed down into
ip_route_me_harder.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI error: init_volumes: not enough PEBs, required 706, available 686
UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1)
UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM
UBI error: ubi_init: cannot attach mtd1
If available PEBs are not enough when initializing volumes, return -ENOSPC
directly. If available PEBs are not enough when initializing WL, return
-ENOSPC instead of -ENOMEM.
Cc: stable@vger.kernel.org
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
Make sure that data_size is less than LEB size.
Otherwise a handcrafted UBI image is able to trigger
an out of bounds memory access in ubi_compare_lebs().
Cc: stable@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: David Gstir <david@sigma-star.at>
Move pxamci to mmc slot-gpio API to fix interrupt request.
It fixes the case where the card detection is on a gpio expander, on I2C
for example on zylonite board. In this case, the card detect netsted
interrupt is called from a threaded interrupt. The request_irq() fails,
because a hard irq cannot be a nested interrupt from a threaded
interrupt (set __setup_irq()).
This was tested on zylonite and mioa701 boards.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In recent allwinner kernel sources the mmc clk-delay settings have been
slightly tweaked, and for sun9i they are completely different then what
we are using.
This commit brings us in sync with what allwinner does, fixing problems
accessing sdcards on some A33 devices (and likely others).
For pre sun9i hardware this makes the following changes:
-At 400Khz change the sample delay from 7 to 0 (introduced in A31 sdk)
-At 50 Mhz change the sample delay from 5 to 4 (introduced in A23 sdk)
This also drops the clk-delay calculation for clocks > 50 MHz, we do
not need this as we've: mmc->f_max = 50000000, and the delays in the
old code were not correct (at 100 MHz the delay must be a multiple of 60,
at 200 MHz a multiple of 120).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When CONFIG_GPIOLIB is unset, its stubs will return -ENOSYS. That means
when the mmc core parses DT for CD/WP GPIOs via mmc_of_parse(), -ENOSYS
becomes propagated to the caller. Typically this means that the mmc host
driver fails to probe.
As the CD/WP GPIOs are already treated as optional, let's extend that to
cover the case when CONFIG_GPIOLIB is unset.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Fixes: 16b23787fc ("mmc: sdhci-of-arasan: Call OF parsing for MMC")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Seemingly innocuous sctp_trans_state_to_prio_map[] array
is way bigger than it looks, since
"[SCTP_UNKNOWN] = 2" expands into "[0xffff] = 2" !
This patch replaces it with switch() statement.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Neil Horman <nhorman@tuxdriver.com>
CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
CC: linux-sctp@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed that the compiler (gcc version 4.8.5 20150623 (Red Hat 4.8.5-4) (GCC))
generated suboptimal assembler code in eth_get_headlen().
This early return coding style is usually not an issue, on super scalar CPUs,
but the compiler choose to put the return statement after this very unlikely
branch, thus creating larger jump down to the likely code path.
Performance wise, I could measure slightly less L1-icache-load-misses
and less branch-misses, and an improvement of 1 nanosec with an IP-forwarding
use-case with 257 bytes packets with ixgbe (CPU i7-4790K @ 4.00GHz).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small chance that tunnel_free() is called before tunnel->del_work scheduled
resulting in a zero pointer dereference.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Application limited streams such as thin streams, that transmit small
amounts of payload in relatively few packets per RTT, can be prevented
from growing the CWND when in congestion avoidance. This leads to
increased sojourn times for data segments in streams that often transmit
time-dependent data.
Currently, a connection is considered CWND limited only after having
successfully transmitted at least one packet with new data, while at the
same time failing to transmit some unsent data from the output queue
because the CWND is full. Applications that produce small amounts of
data may be left in a state where it is never considered to be CWND
limited, because all unsent data is successfully transmitted each time
an incoming ACK opens up for more data to be transmitted in the send
window.
Fix by always testing whether the CWND is fully used after successful
packet transmissions, such that a connection is considered CWND limited
whenever the CWND has been filled. This is the correct behavior as
specified in RFC2861 (section 3.1).
Cc: Andreas Petlund <apetlund@simula.no>
Cc: Carsten Griwodz <griff@simula.no>
Cc: Jonas Markussen <jonassm@ifi.uio.no>
Cc: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Cc: Mads Johannessen <madsjoh@ifi.uio.no>
Signed-off-by: Bendik Rønning Opstad <bro.devel+kernel@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for ethtool get time stamp ioctl, which is used by
tcpdump to get the supported time stamp types
eg: tcpdump -i eth5 -J
Time stamp types for eth5 (use option -j to set):
host (Host)
adapter_unsynced (Adapter, not synced with system time)
Adds support for adapter unsynced mode, by adding SIOCSHWTSTAMP support
in driver.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the compilation error with arm allmodconfig, this error
generated due to unavailability of readq() on 32-bit platform which was
found during net-next daily compilation. In the same time, fix all the
hns drivers compilation warnings.
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: zhaungyuzeng <Yisen.zhuang@huawei.com>
Signed-off-by: kenneth Lee <liguozhu@hisilicon.com>
Signed-off-by: yankejian <yankejian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert pxaficp_ir to dmaengine. As pxa architecture is shifting from
raw DMA registers access to pxa_dma dmaengine driver, convert this
driver to dmaengine.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the pxa IRDA driver to readl and writel primitives, and remove
another set of direct registers access. This leaves only the DMA
registers access, which will be dealt with dmaengine conversion.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using directly the OS timer through direct register access,
use the standard sched_clock(), which will end up in OSCR reading
anyway.
This is a first step for direct access register removal and machine
specific code removal from this driver.
This commit changes the behavior, as previously the minimum turnaround
time was counted in 76ns steps, while with this patch it is counted in
microsecond steps. The strictly equal formula would have been :
while ((sched_clock() - si->last_clk) * 76 < mtt)
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to have FEATURES_NEED_QUIESCE defined as we
can simply use NETIF_F_RXCSUM instead as done in other parts
of the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
