Tested by lyakh on IRC
zd1211 chip 1740:2000 v4721 high 00-02-6f AL7230B_RF pa0 g---
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for another Airoha RF which is present in some
ZD1211 adapters. This RF supports 802.11a as well as 802.11b/g, but 802.11a
connectivity is not yet supported by this driver.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch synchronizes our code to some recent vendor driver modifications.
A new PHY layout is supported, some values are tweaked, and the AL2230 is now
programmed over a new interface which is many times faster.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor driver resets the IFS value every time the channel changes,
to this one.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The vendor driver chooses this value based on an ifndef ASIC,
and ASIC is never defined.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Please include the attached patch that adds support for a new PHY to the
sis900 driver. See also Bugzilla 6919.
Signed-off-by: Daniele Venzano <venza@brownhat.org>
--
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Enabling PXA DMA for the smc91x on the logicpd pxa270 produces
unacceptable interference with the TFT panel, so disable it. Also
delete the lpd270 versions of the SMC_{in,out}[bl]() macros, as they
aren't used, since the board only supports 16bit accesses.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On the 88E805X chipsets (used in laptops), the PHY was not getting powered
out of shutdown properly. The variable reg1 was getting reused incorrectly.
This is probably the cause of the bug.
http://bugzilla.kernel.org/show_bug.cgi?id=6471
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Dummy RDMA are always enabled on device startup since commit
9a71db721a (to work around buggy
PCIe chipsets which do not implement resending properly). But,
we also need to always re-enable them when resuming the device.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch uses the sundance_reset function everywhere a reset is done,
and adds a link to the archives of the original mailing list.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revised version of the forcedeth NAPI support.
This version is based against netdev-2.6#upstream
(after the MAC patches from Ayaz today).
Can't use nv_disable_hw_interrupts because NAPI only wants to
mask off receive irq's and leave the others alone.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch will correct the mac address and set a flag to indicate that
it is already corrected in case nv_probe is called again. For example,
when you use kexec to restart the kernel.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves the mac address setup/teardown to the
nv_probe/nv_remove functions. This fixes WOL wakeup since on nv_close we
would reverse the mac address. Also, bonding driver will reset address
after nv_close is called.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
'mdio_reset' has bad side effects that moves the phy_id.
DL10022-based cards work properly without 'mdio_reset'.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a subtle race condition between tg3_start_xmit() and tg3_tx()
discovered by Herbert Xu <herbert@gondor.apana.org.au>:
CPU0 CPU1
tg3_start_xmit()
if (tx_ring_full) {
tx_lock
tg3_tx()
if (!netif_queue_stopped)
netif_stop_queue()
if (!tx_ring_full)
update_tx_ring
netif_wake_queue()
tx_unlock
}
Even though tx_ring is updated before the if statement in tg3_tx() in
program order, it can be re-ordered by the CPU as shown above. This
scenario can cause the tx queue to be stopped forever if tg3_tx() has
just freed up the entire tx_ring. The possibility of this happening
should be very rare though.
The following changes are made:
1. Add memory barrier to fix the above race condition.
2. Eliminate the private tx_lock altogether and rely solely on
netif_tx_lock. This eliminates one spinlock in tg3_start_xmit()
when the ring is full.
3. Because of 2, use netif_tx_lock in tg3_tx() before calling
netif_wake_queue().
4. Change TX_BUFFS_AVAIL to an inline function with a memory barrier.
Herbert and David suggested using the memory barrier instead of
volatile.
5. Check for the full wake queue condition before getting
netif_tx_lock in tg3_tx(). This reduces the number of unnecessary
spinlocks when the tx ring is full in a steady-state condition.
6. Update version to 3.65.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
All caller of netdev_alloc_skb need to assign skb->dev shortly
afterwards. Move it into common code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
More changes to prevent losing status and causing hangs.
The hardware is smarter than I gave it credit for.
Clearing the status IRQ causes the status state machine to
toggle an IRQ if needed and post any more transmits.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recent vendor driver and customer reports show more devices.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When writing the firmware to the NIC, the FIFO is 256-bytes long,
so we use 256-bytes chunks and a read to wait until the previous
write is done.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent phylib from freeing PHY IRQ twice on closing an eth device:
phy_disconnect() first calls phy_stop_interrupts(), then it calls
phy_stop_machine() which in turn calls phy_stop_interrupts() making the
kernel complain on each bootup...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains some of the bug fixes and enhancements done to
s2io driver. Following are the brief description of changes
1. code cleanup to handle gso modification better
2. Move repeated code in rx path, to a common function
s2io_chk_rx_buffers()
3. Bug fix in MSI interrupt
4. clear statistics when card is down
5. Avoid linked list traversing in lro aggregation.
6. Use pci_dma_sync_single_for_cpu for buffer0 in case of 2/3
buffer mode.
7. ethtool tso get/set functions to set clear NETIF_F_TSO6
8. Stop LRO aggregation when we receive ECN notification
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains some of the bug fixes and enhancements done to
s2io driver. Following are the brief description of changes
1. Introduced macro "S2IO_PARM_INT" for declaring integer load parameter
2. UDP_RR test failure, memset txdl after Tx completion
3. PXE boot may leave adapter in unknown state so do reset in probe.
4. Add Tx completion code in netpoll
5. In s2io_vpd_read() move array vpd_data[] to pointer, saves stack memory
6. Fix bug in ethtool online test
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Otherwise we allow building appletalk drivers in-kernel when
CONFIG_ATALK is modular. That doesn't work because these drivers use
symbols such as "alloc_talkdev" which is exported from code built
by CONFIG_ATALK.
Noticed by Toralf Förster.
Signed-off-by: David S. Miller <davem@davemloft.net>
I had problems with my AVM Fritz!Box access point. It appeared
that the AP deauthorized me and the softmac didn't reconnect me.
This patch handles the problem.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Discovered a problem while accessing www.python.org on my PPC32.
The problem was pretty consistent for all sticks. The reason was
that while testing for the length info tag, I ignored the
endianess of the host system.
Please recognize that converting the constant to little endian, we
create faster code.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is never called in interrupt context, and it doesn't
matter if it is called in IRQ context or not.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently the ZD1211 doesn't mind, but the ZD1211B absolutely must be
told that encryption is happening in software.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We'll be needing these at some point...
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There has been a problem in the radiotap header. Monitor mode
works now with tcpdump 3.94 + libpcap 0.9.4. ethereal 0.99.0 +
libpcap 0.9.4 is broken, because it doesn't find the right offset
for the IEEE 802.11 header.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix-up missing mac_suspended initialization which resulted from
Linville's sloppy patch mangling.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
removes the unneeded local variable rc
replace pci_module_init() with pci_register_driver()
two coding style issues on switch
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use __le32 to indicate byte order of hardware ring elements
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
drivers/net/forcedeth.c | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the coding style of the nForce Ethernet driver.
- typedef's should not be used
- variable names should not be capitialized
- structure tags should be lower case
- add whitespace near keywords
- don't add paren's to switch cases
- remove paren's from return
- don't use __constant_ntohs unless necessary.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
drivers/net/forcedeth.c | 246 ++++++++++++++++++++++++------------------------
1 file changed, 123 insertions(+), 123 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Okay, Fix both typo's in one patch .The impact is that the incorrect value
was being computed for blinking LED and interrupt moderation values.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Always do a dummy RDMA after loading the firmware to work around
buggy PCIe chipsets which do not implement resending properly.
This is so cheap as to be almost free, and should never have been
conditional on the tx boundary != 4096.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a complementary network driver for our ISP4XXX parts.
There is a concurrent effort underway to get the iSCSI driver (qla4xxx)
integrated upstream as well.
I have been through several iterations with the linux-netdev list and have had
much response from Stephen Hemminger.
- Built and tested using kernel 2.6.17-rc4.
- The chip supports two ethernet and two iSCSI functions.
- The functions ql_sem_lock, ql_sem_spinlock, ql_sem_unlock, and
ql_wait_for_drvr_lock are used to protect resources that are shared across
the network and iSCSI functions. This protection is mostly during chip
initialization and resets, but also include link management.
- The PHY/MII are not exported through ethtool due to the fact that the
iSCSI function will control the common link at least 50% of the time.
This driver has been through several iterations on the netdev list and we feel
this driver is ready for inclusion in the upstream kernel.
It has been built and tested on x86 and PPC64 platforms.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This minor patch for wireless-2.6 (softmac) adjusts the parameters of
the wireless statistics to improve the display of programs such as the
"Wireless Network Information" applet of KDE. Thanks to Dan Williams
and Jean Tourrilhes for valuable help in setting up the return of
info in dBm.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite of the bcm43xx initialization routines.
This fixes several issues:
* up-down-up-down-up... stale data issue
(May fix some DHCP issues)
* Fix the init vs IRQ handler race (and remove the workaround)
* Fix init for cards with multiple cores (APHY)
As softmac has no internal PHY handling (unlike dscape),
this adds the file "phymode" to sysfs.
The active PHY can be selected by writing either a, b or g
to this file. Current PHY can be determined by reading from it.
* Fix the controller restart code.
Controller restart can now also be triggered through
echo 1 > /debug/bcm43xx/ethX/restart
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes mac_suspend reference counting for
ifconfig up
ifconfig down
ifconfig up
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Microoptimization:
This reduces the udelay in bcm43xx_mac_suspend.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Suspend MAC (and make MAC-suspend refcounting) when doing
long periodic work.
On long periodic work, we disable IRQs on the device, so
we don't want the MAC to stay operating and probably miss
packets due do non-delivery of interrupts.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add WE-19 capabilities to prism54 fullmac driver so that it supports the
necessary Wireless Extensions WPA calls. Convert reporting of WPA/RSN
Generic Information Elements to IWEVGENIE rather than pre-WE-19
IWEVCUSTOM as well.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless.h discourages using SIOCGIWNAME to publish the driver name
which the interface belongs to. Use SIOCGIWNICKN instead.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw2200 uses // comments, and uses them for removing unneeded
code. Clean it up a bit.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When determining whether there's a key to set or not, orinoco should be
looking at the key length, not the key data. Otherwise confusion reigns
when trying to set TX key only, passing in zero-length key, but non-NULL
pointer. Key length takes precedence over non-NULL key data.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johann Uhrmann reported a bcm43xx crash and Michael Buesch tracked
it down to a problem with the new shared key auth code (recursive
calls into the driver)
This patch (effectively Michael's patch with a couple of small
modifications) solves the problem by sending the authentication
challenge response frame from a workqueue entry.
I also removed a lone \n from the bcm43xx messages relating to
authentication mode - this small change was previously discussed but
not patched in.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver airo (for Cisco Wlan-Cards) complains about "failed to load
transform for AES", when it is loaded and CRYPTO_AES is not selected
in Kconfig.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1201 has nasty tendency to emit magicall anti-wifi cloud when it is
inserted into slot, but not used.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle dev_alloc_skb() failures when initializing the RX rings.
Without proper handling, the driver will crash when using a partial
ring.
Thanks to Stephane Doyon <sdoyon@max-t.com> for reporting the bug and
providing the initial patch.
Howie Xu <howie@vmware.com> also reported the same issue.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tg3_restart_hw() to handle failures when re-initializing the
device.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It before entering in the loop for freeing the other ifb devices.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pci_register_driver instead of pci_module_init. Use PCI_DEVICE macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WAN: Fixed a problem with PPP/raw HDLC/X.25 protocols not doing
netif_dormant_off() at startup.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The via-velocity driver reports incorrect speed and link detected status
as viewed by ethtool (and probably other tools). This patch fixes those
incorrect reports and prettifies a long line.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The 8390 drivers use disable_irq() as a locking primitive, which means these
uses need lockdep specific annotation that they are used as such.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Get rid of the MODULE stuff. Could have rewritten to use modern interfaces
but the copyright message of this BSD licensed code isn't interesting enough
to be watched on every bootup, in every syslog.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert selection of serial line header compression to use CONFIG_SLHC
rather than makefile ifeq uglyness. This makes it easier to select
the SLHC module from other code.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With this patch TX queue descriptors are not chained per default any more.
The pointer to next descriptor is set only when next descriptor is prepaired
for transfer. Also the mechanism of checking wether Spider is ready has been
changed: it checks not for CARDOWNED flag in status of previous descriptor
but for a TXDMAENABLED flag in Spider's register.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We want to intitialize addr instead of data register first.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When sky2 driver gets lots of received packets at once, it can get stuck.
The NAPI poll routine gets called back to keep going, but since no IRQ bits
are set it doesn't make progress.
Increase version, since this is serious enough problem that I want to be
able to tell new from old problems.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A panic was reported when receiving 1522 size packets if using
the default MTU. we should set the initial rx buffer length to the
value that e1000changemtu sets so that we can receive any packet
that would not be dropped by LPE=0.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke.jan.h.kok@intel.com>
After removing the hardware CRC stripping which causes problems with
SOL and related issues, we need to compensate for this changed size.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The original suggested fix for netpoll was found to be racy on SMP
kernels. While it is highly unlikely that this race would ever be seen
in the real world due to current netpoll usage models, we implemented
this updated fix to address concerns.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
* HEAD:
[NET]: fix __sk_stream_mem_reclaim
[Bluetooth] Fix deadlock in the L2CAP layer
[Bluetooth] Let BT_HIDP depend on INPUT
[Bluetooth] Avoid NULL pointer dereference with tty->driver
[Bluetooth] Remaining transitions to use kzalloc()
[WAN]: converting generic HDLC to use netif_dormant*()
[IPV4]: Fix error handling for fib_insert_node call
[NETROM] lockdep: fix false positive
[ROSE] lockdep: fix false positive
[AX.25]: Optimize AX.25 socket list lock
[IPCOMP]: Fix truesize after decompression
[IPV6]: Use ipv6_addr_src_scope for link address sorting.
[TCP] tcp_highspeed: Fix AI updates.
[MAINTAINERS]: Add proper entry for TC classifier
[NETROM]: Drop lock before calling nr_destroy_socket
[NETROM]: Fix locking order when establishing a NETROM circuit.
[AX.25]: Fix locking of ax25 protocol function list.
[IPV6]: order addresses by scope
When the driver handles multiple packets per NAPI poll, it is
better to reload the receive ring, then tell the hardware. Otherwise,
under packet storm with flow control, the driver/hardware will degrade
down to one packet getting through per pause-exchange.
Likewise on transmit, don't wakeup until a little more than minimum
ring space is available.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The documentation says we need to wait after turning on the PHY.
Also, don't enable WOL by default.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The changes to handle suspend/resume didn't handle the case where
a dual port card has the first port down, but the second is running.
In this driver, all NAPI polling is done on the primary port.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since sky2_reset gets call from sky2_resume it shouldn't be tagged
with devinit.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to correct broken collision threshold mask in (same problem
as sky2 driver). Should be three bits wide, but the mask only allows
for 1 bit to be set.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to correct broken collision threshold mask in (same problem
as sky2 driver). Should be three bits wide, but the mask only allows
for 1 bit to be set.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Patch to correct broken collision threshold mask in sky2 driver. Should be
three bits wide, but the mask only allows for 1 bit to be set.
Thanks & Regards
Neil
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
sky2.h | 2 +-
1 files changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Morton wrote:
> All these functions return error codes, and we're not checking them. We
> should. So there's a patch which marks all these things as __must_check,
> which causes around 1,500 new warnings.
>
The following patch fixes such a warning in myri10ge.
Check pci_enable_device() return value in myri10ge_resume().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We need to specify a Versatile-specific SMC_IRQ_FLAGS value or the new
generic IRQ layer will complain thusly:
No IRQF_TRIGGER set_type function for IRQ 25 (<NULL>)
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There were some tso bugs that only showed up with heavy load and 16kB
pages that this patch fixes by making the driver's internal use count
of descriptors match the count that it was estimating it needed using
the DESC_NEEDED macro. This bug caused NETDEV_WATCHDOG resets aka
tx timeouts.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
subsystem_configurations array is only used by an __init function,
therefore it should be marked __initdata, not __devinitdata.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/8139cp.c: In function 'cp_init_one':
drivers/net/8139cp.c:1919: warning: format '%lx' expects type 'long unsigned int', but argument 4 has type 'resource_size_t'
drivers/net/8139cp.c:1919: warning: format '%lx' expects type 'long unsigned int', but argument 5 has type 'resource_size_t'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Modification and bug fixes with respect to irq registration.
- Enable interrupts after request_irq
- Restored MSI data register value at driver unload time
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use the new names.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch defines the watermark registers and fixes up the use of this
register.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the definition for the deferral registers and fixes up
the use of these registers.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch converts generic HDLC (and WAN drivers using it) from
hdlc_set_carrier() to netif_dormant*() interface.
WAN hardware drivers should now use netif_carrier_on|off() like
other network drivers.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bpqether is encapsulating AX.25 frames into ethernet frames. There is a
virtual bpqether device paired with each ethernet devices, so it's normal
to pass through dev_queue_xmit twice for each frame which triggers the
locking detector.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use release_firmware() to free requested resources.
According to Documentation/firmware_class/README the request_firmware()
call should be followed by a release_firmware(). Some drivers do not
however free the firmware previously allocated with request_firmware().
This patch tries to fix this by making sure that release_firmware() is used
as expected.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on a patch by Matthieu CASTET.
zd1211 chip 079b:004a v4330 high 00-60-b3 AL2230_RF pa0 g--
zd1211b chip 079b:0062 v4810 high 00-60-b3 AL2230_RF pa0 g--
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch improves the statistics returned from
bcm43xx_get_wireless_stats. The signal level comes from smoothing the
"rssi" value returned by the firmware after it is converted into a
dBm value by the driver. The quality value is a hack derived from the
smoothed level and an assumed RX_POWER_MAX of -10 dBM. The noise value
is still the one calculated from the clean-room formula. On my system,
this is roughly -65 dBm, which seems too high.
The revised version uses the ieee80211 spinlock to protect traversing
of the network list.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds voluntary preemption points into the
PHY calibration loops to allow non-CONFIG_PREEMPT machines
to not suffer from huge delays.
CONFIG_PREEMPT machines are already fine, because all this
code is run in non-atomic process context.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As many people don't seem to like the locking "obfuscation"
in the bcm43xx driver, this patch removes it.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will reimplement halt-clearing later, when we have periodic
housekeeping routines in place. This will do as a temporary fix, the
EPIPE case has not yet been seen.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An assert statement near the start of handle_irq_noise in the softmac
version of bcm43xx_main.c is there to protect against out of bound
addressing using variable bcm->noisecalc.nr_samples. The arrays in
question have a dimension of 8, thus the value must be < 8.
Signed-Off-By: Larry.Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the wrapper function skb_is_gso which can be used instead
of directly testing skb_shinfo(skb)->gso_size. This makes things a little
nicer and allows us to change the primary key for indicating whether an skb
is GSO (if we ever want to do that).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Coverity checker spotted, that from the changes from commit
898b1d16f8 the
if (ret)
platform_driver_unregister(&ali_ircc_driver);
was dead code.
This patch changes this function to what seems to have been the
intention.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the AMD 8131 bridge to the list of chipsets that reorder writes.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
> stack backtrace:
> [<f9099d31>] rtl8139_start_xmit+0xd9/0xff [8139too]
> [<c11ad5ea>] netpoll_send_skb+0x98/0xea
This seems to be a real deadlock...
So netpoll_send_skb takes the _xmit_lock, which is all nitty gritty
but then rtl8139_start_xmit comes around while that lock is taken, and
does
spin_unlock_irq(&tp->lock);
which.. enables interrupts and softirqs; this is quite bad because the
xmit lock is taken in softirq context for the watchdog like this:
[<c1200376>] _spin_lock+0x23/0x32
[<c11af282>] dev_watchdog+0x14/0xb1
[<c101dab2>] run_timer_softirq+0xf2/0x14a
[<c101a691>] __do_softirq+0x55/0xb0
[<c1004a8d>] do_softirq+0x58/0xbd
Which would deadlock now that the spin_unlock_irq() has enabled
irqs/softirqs while the _xmit_lock is still held.
The patch below turns this into a irqsave/irqrestore pair so that
interrupts don't get enabled unconditionally.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver source code is not the preferred place to store change history.
Acked-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the IRQ line, the tx_boundary, and whether Write-combining and MSI
are enabled to the list of parameters that are exported to ethtool.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Displaying the interface name when listing the device parameters
at the end of myri10ge_probe is not a good idea since udev might
rename the interface soon afterwards.
Print the bus id instead, using dev_info().
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The workaround for the AER capability of the nVidia chipset has been
removed, we don't need this PCI id anymore. Drop it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The pm_state field in the myri10ge_priv structure is unused. Drop it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove dead entry from net wan Kconfig and net wan Makefile.. This entry is
left over from 2.4 where synclink used syncppp driver directly. synclink
drivers now use generic HDLC
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- updated MAINTAINERS entry to new format
- updated Jan-Pascal's (ACKed) and my email address
- driver cleanup/modernization (runtime-, not hardware-tested)
[bunk@stusta.de: build fix]
Signed-off-by: Andreas Mohr <andi@lisas.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jan-Pascal van Best <jvbest@qv3pluto.leidenuniv.nl>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Barry K. Nathan reported the following lockdep warning:
[ 197.343948] BUG: warning at kernel/lockdep.c:1856/trace_hardirqs_on()
[ 197.345928] [<c010329b>] show_trace_log_lvl+0x5b/0x105
[ 197.346359] [<c0103896>] show_trace+0x1b/0x20
[ 197.346759] [<c01038ed>] dump_stack+0x1f/0x24
[ 197.347159] [<c012efa2>] trace_hardirqs_on+0xfb/0x185
[ 197.348873] [<c029b009>] _spin_unlock_irq+0x24/0x2d
[ 197.350620] [<e09034e8>] do_tx_done+0x171/0x179 [ns83820]
[ 197.350895] [<e090445c>] ns83820_irq+0x149/0x20b [ns83820]
[ 197.351166] [<c013b4b8>] handle_IRQ_event+0x1d/0x52
[ 197.353216] [<c013c6c2>] handle_level_irq+0x97/0xe1
[ 197.355157] [<c01048c3>] do_IRQ+0x8b/0xac
[ 197.355612] [<c0102d9d>] common_interrupt+0x25/0x2c
this is caused because the ns83820 driver re-enables irq flags
in hardirq context.
While legal in theory, in practice it should only be done if the
hardware is really old and has some very high overhead in its ISR.
(such as PIO IDE)
For modern hardware, running ISRs with irqs enabled is discouraged,
because 1) new hardware is fast enough to not cause latency problems
2) allowing the nesting of hardware interrupts only 'spreads out'
the handling of the current ISR, causing extra cachemisses that would
otherwise not happen. Furthermore, on architectures where ISRs share
the kernel stacks, enabling interrupts in ISRs introduces a much
higher kernel-stack-nesting and thus kernel-stack-overflow risk.
3) not managing irq-flags via the _irqsave / _irqrestore variants
is dangerous: it's easy to forget whether one function nests inside
another, and irq flags might be mismanaged.
In the few cases where re-enabling interrupts in an ISR is considered
useful (and unavoidable), it has to be taught to the lock validator
explicitly (because the lock validator needs the "no ISR ever enables
hardirqs" artificial simplification to keep the IRQ/softirq locking
dependencies manageable).
This teaching is done via the explicit use local_irq_enable_in_hardirq().
On a stock kernel this maps to local_irq_enable(). If the lock validator
is enabled then this does not enable interrupts.
Now, the analysis of drivers/net/ns83820.c's irq flags use: the
irq-enabling in irq context seems intentional, but i dont think it's
justified. Furthermore, the driver suffers from problem #3 above too,
in ns83820_tx_timeout() it disables irqs via local_irq_save(), but
then it calls do_tx_done() which does a spin_unlock_irq(),
re-enabling for a function that does not expect it! While currently
this bug seems harmless (only some debug printout seems to be
affected by it), it's nevertheless something to be fixed.
So this patch makes the ns83820 ISR irq-flags-safe, and cleans up
do_tx_done() use and locking to avoid the ns83820_tx_timeout() bug.
From: Arjan van de Ven <arjan@linux.intel.com>
ns83820_mib_isr takes the misc_lock in IRQ context. All other places that
do this in the ISR already use _irqsave versions, make this consistent at
least. At some point in the future someone should audit the driver to see
if all _irqsave's in the ISR can go away, this is generally an iffy/fragile
proposition though; for now get it safe, simple and consistent.
From: Arjan van de Ven <arjan@linux.intel.com>
ok this is a real driver deadlock:
The ns83820 driver enabled interrupts (by unlocking the misc_lock with
_irq) while still holding the rx_info.lock, which is required to be irq
safe since it's used in the ISR like this:
writel(1, dev->base + IER);
spin_unlock_irq(&dev->misc_lock);
kick_rx(ndev);
spin_unlock_irq(&dev->rx_info.lock);
This is can cause a deadlock if an irq was pending at the first
spin_unlock_irq already, or if one would hit during kick_rx().
Simply remove the first _irq solves this
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More cleanup to pcnet32_loopback_test to release receive buffers if
device is not up. Created common routine to free rx buffers.
Tested ia32 and ppc64
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Suspend the chip if possible rather than stop and discard all tx and rx
frames, when changing the mcast list or entering/leaving promiscuous
mode. Created common pcnet32_suspend routine.
Tested ia32 and ppc64
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix pcnet32_set_ringparam to handle memory allocation errors without
leaving the adapter in an inoperative state and null pointers waiting to
be dereferenced.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On 2006-03-08 Eric Sesterhenn wrote:
converts drivers/net to kzalloc usage.
Don Fry modified it to use netif_msg_drv. Tested ia32 and ppc64.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
