All the debug prints have been replaced with pr_debug(). Thus, the dependency on
dss_debug variable is replaced with dyndbg in dynamic debugging mode and DEBUG
flag otherwise. So, the dss_debug variable is removed along with checks for
DEBUG flag.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The printk in DSSDBG function definition is replaced with dynamic debug enabled
pr_debug(). The use of dynamic debugging provides more flexibility as each debug
statement can be enabled or disabled dynamically on basis of source filename,
line number, module name etc., by writing to a control file in debugfs
filesystem. For better understanding please refer to
Documentation/dynamic-debug-howto.txt.
The DSSDBGF() differs from DSSDBG() by providing function name. However,
function name, line number, module name and thread ID can be printed through
dynamic debug by setting appropriate flags 'f','l','m' and 't' in the debugfs
control file. So, DSSDBGF instances are replaced with DSSDBG.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The config option CONFIG_OMAP2_DSS_DEBUG_SUPPORT has been removed and replaced
with CONFIG_OMAP2_DSS_DEBUG and CONFIG_OMAP2_DSS_DEBUGFS. CONFIG_OMAP2_DSS_DEBUG
enables DEBUG flag and CONFIG_OMAP2_DSS_DEBUGFS enables creation of debugfs for
OMAPDSS. Both the config options are disabled by default and can be enabled
independently of one another as per convenience.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In OMAPDSS the DEBUG flag is set only after the OMAPDSS module is called, for
which the debugging capabilities are available only after its proper
initialization. As a result of which tracking of bugs prior to or during initial
process becomes difficult. So, the definition of DEBUG is being moved to the
corresponding Makefile.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add functions to enable writeback, and set/check state of GO bit. These bits are
identical in behaviour with the corresponding overlay manager bits. Configure
them in a similar way to mgr_enable() and mgr_go_* functions. Add a helper to
get the FRAMEDONE irq corresponding to writeback.
Signed-off-by: Archit Taneja <archit@ti.com>
Configure some of the writeback specific parameters in dispc_wb_setup(). The
writeback parameters configured are:
truncation: This needs to be set if the color depth input to writeback is more
than the color depth of the color mode we want to store in memory.
writeback mode: This configures whether we want to use writeback in mem to mem
or capture mode. This information will be directly passed by APPLY later.
Signed-off-by: Archit Taneja <archit@ti.com>
Create struct omap_dss_writeback_info, this is similar to omap_overlay_info,
the major difference is that there is no parameter which describes the input
size to writeback, this is because this is always fixed, and decided by the
connected overlay or overlay manager. One more difference is that screen_width
is renamed to buf_width, to give the value of stride the writeback buffer has.
Call dispc_ovl_setup_common() through dispc_wb_setup() to configure overlay-like
parameters. The parameters in dispc_ovl_setup_common() which do not hold for
writeback are filled passed as zeroes or false, the code takes care of not
configuring them as they won't possess the needed overlay caps.
Signed-off-by: Archit Taneja <archit@ti.com>
Writeback can take input from either one of the overlays, or one of the overlay
managers. Add an enum which represents the channel_in for writeback, and maps
to the register field programming.
Add a function to configure channel in for writeback. This will be used later in
APPLY.
Signed-off-by: Archit Taneja <archit@ti.com>
The scalers of overlays and writeback do not have any constraints on downscale
ratio when operating in memory to memory mode.
This is because in memory to memory mode, we aren't connected to a display which
needs data output at the rate of pixel clock. The scalers can perform as much
downscaling as needed, the rate at which the scaler outputs is adjusted
accordingly.
Relax constraints related to downscaling based on whether the input overlays are
connected to writeback in memory to memory mode. We pass a mem_to_mem boolean
parameter to dispc_ovl_setup() from APPLY. This is currently set to false, this
will later be configured to the correct value based on whether the overlay is
connected to writeback or not. Do the same later for writeback when writeback is
configured.
In the scaling calculation code, we calculate the minimum amount of core clock we
need to achieve the required downscaling. If we are in memory to memory mode, we
set this to a very small value(1 in this case), this value would always be
lesser than the actual DISPC core clock value, and hence the scaling checks
would succeed.
We take care that pixel clock isn't calculated for writeback and the overlays
connected to it when in memory to memory mode. A pixel clock in such cases
doesn't make sense.
Signed-off-by: Archit Taneja <archit@ti.com>
The struct omap_overlay_info passed to dispc_ovl_setup() is used to configure
DISPC registers. It shouldn't modify the overlay_info structure. The pos_y field
was being changed in dispc_ovl_setup in the case of interlaced displays. Fix
this and const qualifier to the omap_overlay_info argument.
Signed-off-by: Archit Taneja <archit@ti.com>
Links between DSS entities are made in dss_init_connections() when a panel
device is registered, and are removed in dss_uninit_connections() when the
device is unregistered. Modify these functions to incorporate the addition of
outputs.
The fields in omap_dss_device struct gives information on which output and
manager to connect to. The desired manager and output pointers are retrieved and
prepared to form the desired links. The output is linked to the device, and then
the manager to the output.
A helper function omapdss_get_output_from_device() is created to retrieve the
output from the display by checking it's type, and the module id in case of DSI.
Signed-off-by: Archit Taneja <archit@ti.com>
Add set_output/unset_output ops for overlay managers, these form links between
managers and outputs. Create a function in dss features which tell all the
output instances that connect to a manager, use it when a manager tries to set
an output. Add a constraint of not unsetting an output when the manager is
enabled.
Keep the omap_dss_device pointer and set/unset_device ops in overlay_manager for
now to not break things. Keep the dss feature function get_supported_displays
as it's used in some places. These will be removed later.
Signed-off-by: Archit Taneja <archit@ti.com>
The current OMAPDSS design contains 3 software entities: Overlays, Managers and
Devices. These map to pipelines, overlay managers and the panels respectively in
hardware. One or more overlays connect to a manager to represent a composition,
the manager connects to a device(generally a display) to display the content.
The part of DSS hardware which isn't represented by any of the above entities
are interfaces/outputs that connect to an overlay manager, i.e blocks like DSI,
HDMI, VENC and so on. Currently, an overlay manager directly connects to the
display, and the output to which it is actually connected is ignored. The panel
driver of the display is responsible of calling output specific functions to
configure the output.
Adding outputs as a new software entity gives us the following benefits:
- Have exact information on the possible connections between managers and
outputs: A manager can't connect to each and every output, there only limited
hardware links between a manager's video port and some of the outputs.
- Remove hacks related to connecting managers and devices: Currently, default
links between managers and devices are set in a not so clean way. Matching is
done via comparing the device type, and the display types supported by the
manager. This isn't sufficient to establish all the possible links between
managers, outputs and devices in hardware.
- Make panel drivers more generic: The DSS panel drivers currently call
interface/output specific functions to configure the hardware IP. When making
these calls, the driver isn't actually aware of the underlying output. The
output driver extracts information from the panel's omap_dss_device pointer
to figure out which interface it is connected to, and then configures the
corresponding output block. An example of this is when a DSI panel calls
dsi functions, the dsi driver figures out whether the panel is connected
to DSI1 or DSI2. This isn't correct, and having output as entities will
give the panel driver the exact information on which output to configure.
Having outputs also gives the opportunity to make panel drivers generic
across different platforms/SoCs, this is achieved as omap specific output
calls can be replaced by ops of a particular output type.
- Have more complex connections between managers, outputs and devices: OMAPDSS
currently doesn't support use cases like 2 outputs connect to a single
device. This can be achieved by extending properties of outputs to connect to
more managers or devices.
- Represent writeback as an output: The writeback pipeline fits well in OMAPDSS
as compared to overlays, managers or devices.
Add a new struct to represent outputs. An output struct holds pointers to the
manager and device structs to which it is connected. Add functions which can
register/unregister an output, or look for one. Create an enum which represent
each output instance.
Signed-off-by: Archit Taneja <archit@ti.com>
This series adds basic OMAP5 DSS functionality, mainly related to DSS core, DPI
and DSI.
* omap5-dss:
OMAPDSS: DSI: make OMAP2_DSS_DSI depend on ARCH_OMAP5
OMAPDSS: DSI: Add code to disable PHY DCC
OMAPDSS: DSI: Add new linebuffer size for OMAP5
OMAPDSS: DSI: Add FEAT_DSI_PLL_REFSEL
OMAPDSS: DSI: Add FEAT_DSI_PLL_SELFREQDCO
OMAPDSS: Add support for DPI source selection
OMAPDSS: move dss feats to the end of dss.c
OMAPDSS: Add basic omap5 features to dss and dispc
OMAPDSS: DSI: improve DSI clock calcs for DISPC
We can select the video source for DPI output as follows:
OMAP2/3: always LCD1
OMAP4: LCD2 or DIGIT
OMAP5: LCD1/LCD2/LCD3/DIGIT
This patch adds support to select the source, and makes dpi.c call the
function to set the source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Anders <x0132446@ti.com>
We currently create omap_dss_devices statically in board files, and use
those devices directly in the omapdss driver. This model prevents us
from having the platform data (which the dssdevs in board files
practically are) as read-only, and it's also different than what we will
use with device tree.
This patch changes the model to be in line with DT model: we allocate
the dssdevs dynamically, and initialize them according to the data in
the board file's dssdev (basically we memcopy the dssdev fields).
The allocation and registration is done in the following steps in the
output drivers:
- Use dss_alloc_and_init_device to allocate and initialize the device.
The function uses kalloc and device_initialize to accomplish this.
- Call dss_copy_device_pdata to copy the data from the board file's
dssdev
- Use dss_add_device to register the device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cleanup dss_recheck_connections, move and rename it to a static
dss_init_connections function inside display.c. Improve the function to
return errors, and implement a matching dss_uninit_connections that can
be used to free the mgr->dssdev link.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have boards with multiple panel devices connected to the same
physical output, of which only one panel can be enabled at one time.
Examples of these are Overo, where you can use different daughter boards
that have different LCDs, and 3430SDP which has an LCD and a DVI output
and a physical switch to select the active display.
These are supported by omapdss so that we add all the possible display
devices at probe, but the displays are inactive until somebody enables
one. At this point the panel driver starts using the DSS, thus reserving
the physcal resource and excluding the other panels.
This is problematic:
- Panel drivers can't allocate their resources properly at probe(),
because the resources can be shared with other panels. Thus they can
be only reserved at enable time.
- Managing this in omapdss is confusing. It's not natural to have
child devices, which may not even exist (for example, a daughterboard
that is not connected).
Only some boards have multiple displays per output, and of those, only
very few have possibility of switching the display during runtime.
Because of the above points:
- We don't want to make omapdss and all the panel drivers more complex
just because some boards have complex setups.
- Only few boards support runtime switching, and afaik even then it's
not required. So we don't need to support runtime switching.
Thus we'll change to a model where we will have only one display device
per output and this cannot be (currently) changed at runtime. We'll
still have the possibility to select the display from multiple options
during boot with the default display option.
This patch accomplishes the above by changing how the output drivers
register the display device. Instead of registering all the devices
given from the board file, we'll only register one. If the default
display option is set, the output driver selects that display from its
displays. If the default display is not set, or the default display is
not one of the output's displays, the output driver selects the first
display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We used to have all the displays of the board in one list, and we made a
"displayX" directory in the sysfs, where X was the index of the display
in the list.
This doesn't work anymore with device tree, as there's no single list to
get the number from, and it doesn't work very well even with non-DT as
we need to do some tricks to get the index nowadays.
This patch changes omap_dss_register_device() so that it doesn't take
disp_num as a parameter anymore, but uses a private increasing counter
for the display number.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Separate sysfs code for managers to a separate file. This is a bit
cleaner, and will allow us later to easily switch off the sysfs support
via Kconfig option.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Separate sysfs code for overlays to a separate file. This is a bit
cleaner, and will allow us later to easily switch off the sysfs support
via Kconfig option.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Functions dss_calc_clock_rates() and dss_get_clock_div() are removed as these
functions have become redundant and no longer used.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The VENC driver currently relies on the omap_dss_device struct to configure the
video output polarity. This makes the VENC interface driver dependent on the
omap_dss_device struct.
Make the VENC driver data maintain it's own polarity field. A panel driver
is expected to call omapdss_venc_invert_vid_out_polarity() before enabling the
interface.
Signed-off-by: Archit Taneja <archit@ti.com>
The VENC driver currently relies on the omap_dss_device struct to configure the
venc type. This makes the VENC interface driver dependent on the omap_dss_device
struct.
Make the VENC driver data maintain it's own 'venc type' field. A panel driver
is expected to call omapdss_venc_set_type() before enabling the interface or
changing the type via display sysfs attributes.
Signed-off-by: Archit Taneja <archit@ti.com>
The SDI driver currently relies on the omap_dss_device struct to configure the
number of data pairs as specified by the panel. This makes the SDI interface
driver dependent on the omap_dss_device struct.
Make the SDI driver data maintain it's own data lines field. A panel driver
is expected to call omapdss_sdi_set_datapairs() before enabling the interface.
Even though we configure the number of data pairs here, this function would be
finally mapped to a generic interface op called set_data_lines. The datapairs
argument type has been changed from u8 to int at some places to be in sync with
the 'set_data_lines' ops of other interfaces.
Signed-off-by: Archit Taneja <archit@ti.com>
The current venc.c driver contains both the interface and panel driver code.
This makes the driver hard to read, and difficult to understand the work split
between the interface and panel driver and the how the locking works.
This also makes it easier to clearly define the VENC interface ops called by the
panel driver.
Split venc.c into venc.c and venc_panel.c representing the interface and panel
driver respectively. This split is done along the lines of the HDMI interface
and panel drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
The hdmi driver currently updates only the 'code' member of hdmi_config when
the op omapdss_hdmi_display_set_timing() is called by the hdmi panel driver.
The 'timing' field of hdmi_config is updated only when hdmi_power_on is called.
It makes more sense to configure the whole hdmi_config field in the set_timing
op called by the panel driver. This way, we don't need to call both functions
to ensure that our hdmi_config is configured correctly. Also, we don't need to
calculate hdmi_config during hdmi_power_on, or rely on the omap_video_timings
in the panel's omap_dss_device struct.
The default timings of the hdmi panel are represented in a cleaner form. Since
the hdmi output is now configured by it's own copy of timings (in
hdmi.ip_data.cfg), the panel driver needs to set it to a valid value before
enabling hdmi output. We now call omapdss_hdmi_set_timing() before enabling
hdmi output, this is done to atleast have the hdmi output configured to the
panel's default timings if the DSS user didn't call panel driver's set_timings()
op explicitly.
Signed-off-by: Archit Taneja <archit@ti.com>
The function dss_mgr_set_timings is supposed to apply timings passed by an
interface driver. It is not supposed to change the timings. Add const qualifier
to the omap_video_timings pointer argument in dss_mgr_set_timings().
Signed-off-by: Archit Taneja <archit@ti.com>
Replication logic for an overlay depends on the color mode in which it is
configured and the video port width of the manager it is connected to.
video port width now held in dss_lcd_mgr_config in the manager's private
data in APPLY. Use this instead of referring to the omap_dss_device connected to
the manager.
Replication is enabled in the case of TV manager, the video_port_width is set to
a default value of 24 for TV manager.
Make the replication checking an overlay function since it's more of an overlay
characteristic than a display characteristic.
Signed-off-by: Archit Taneja <archit@ti.com>
The LCD related manager configurations are a part of the manager's private data
in APPLY. Pass this to dss_lcd_mgr_config to dss_mgr_check and create a function
to check the validity of some of the configurations.
To check some of the configurations, we require information of interface to
which the manager output is connected. These can be added once interfaces are
represented as an entity.
Signed-off-by: Archit Taneja <archit@ti.com>
Replace the DISPC fuctions used to configure LCD channel related manager
parameters with dss_mgr_set_lcd_config() in APPLY. This function ensures that
the DISPC registers are written at the right time by using the shadow register
programming model.
The LCD manager configurations is stored as a private data of manager in APPLY.
It is treated as an extra info as it's the panel drivers which trigger this
apply via interface drivers, and not a DSS2 user like omapfb or omapdrm.
Storing LCD manager related properties in APPLY also prevents the need to refer
to the panel connected to the manager for information. This helps in making the
DSS driver less dependent on panel.
A helper function is added to check whether the manager is LCD or TV. The direct
DISPC register writes are removed from the interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Create a struct dss_lcd_mgr_config which holds LCD overlay manager related
parameters. These are currently partially contained in the omap_dss_device
connected to the manager, and the rest are in the interface driver.
The parameters are directly written to the DISPC registers in the interface
drivers. These should eventually be applied at the correct time using the
shadow register programming model. This struct would help in grouping these
parameters so that they can be applied together.
Signed-off-by: Archit Taneja <archit@ti.com>
dipsc_mgr_set_clock div has an int return type to report errors or success.
The function doesn't really check for errors and always returns 0. Change
the return type to void.
Checking for the correct DISPC clock divider ranges will be done when a DSS2
user does a manager apply. This support will be added later.
Signed-off-by: Archit Taneja <archit@ti.com>
Currently the interlace parameter passed to dispc_ovl_setup() is configured by
checking the display type, and set to true if the display type is VENC.
This isn't correct as other panels can take interlaced content too. The
omap_video_timings struct in manager's private data contains the info whether
the panel is in interlaced mode or not.
Signed-off-by: Archit Taneja <archit@ti.com>
dispc_mgr_set_pol_freq() configures the fields in the register DISPC_POL_FREQo.
All these fields have been moved to omap_video_timings struct, and are now
programmed in dispc_mgr_set_lcd_timings(). These will be configured when timings
are applied via dss_mgr_set_timings().
Remove dispc_mgr_set_pol_freq() and it's calls from the interface drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Remove configuration of Ac-bias pins
Ac-bias pins need to be configured only for passive matrix displays. Remove
acbi and acb fields in omap_dss_device and their configuration in panel
drivers. Don't program these fields in DISP_POL_FREQo register any more.
The panel driver for sharp-ls037v7dw01, and the panel config for
Innolux AT070TN8 in generic dpi panel driver set acb to a non zero value. This
is most likely carried over from the old omapfb driver which supported passive
matrix displays.
Cc: Thomas Weber <weber@corscience.de>
Signed-off-by: Archit Taneja <archit@ti.com>
Remove omap_lcd_display_type enum
The enum omap_lcd_display_type is used to configure the lcd display type in
DISPC. Remove this enum and always set display type to TFT by creating function
dss_mgr_set_lcd_type_tft().
Signed-off-by: Archit Taneja <archit@ti.com>
Remove clock constraints related to passive matrix displays.
There is a constraint (pcd_min should be 3) for passive matrix displays. Remove
this constraint in clock divider calculations as we won't support passive
matrix displays any more.
This cleans up the functions which calculate the clock dividers with DSI's PLL
or DSS_FCLK as the clock source.
Signed-off-by: Archit Taneja <archit@ti.com>
The current implementation of LCD channels and managers consists of a number of
if-else construct which has been replaced by a simpler interface. A constant
structure mgr_desc has been created in Display Controller (DISPC) module. The
mgr_desc contains for each channel its name, irqs and is initialized one time
with all registers and their corresponding fields to be written to enable
various features of Display Subsystem. This structure is later used by various
functions of DISPC which simplifies the further implementation of LCD channels
and its corresponding managers.
Signed-off-by: Chandrabhanu Mahapatra <cmahapatra@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There is a problem related to DSS FIFO thresholds and power management
on OMAP3. It seems that when the full PM hits in, we get underflows. The
core reason is unknown, but after experiments it looks like only
particular FIFO thresholds work correctly.
This bug is related to an earlier patch, which added special FIFO
threshold configuration for OMAP3, because DSI command mode output
didn't work with the normal threshold configuration.
However, as the above work-around worked fine for other output types
also, we currently always configure thresholds in this special way on
OMAP3. In theory there should be negligible difference with this special
way and the standard way. The first paragraph explains what happens in
practice.
This patch changes the driver to use the special threshold configuration
only when the output is a manual update display on OMAP3. This does
include RFBI displays also, and although it hasn't been tested (no
boards using RFBI) I suspect the similar behaviour is present there
also, as the DISPC side should work similarly for DSI command mode and
RFBI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Joe Woodward <jw@terrafix.co.uk>
Implement the DSS device driver audio support interface in the HDMI
panel driver and generic driver. The implementation relies on the
IP-specific functions that are defined at DSS probe time.
A mixed locking strategy is used. The panel's mutex is used when
the state of the panel is queried as required by the audio functions.
The audio state is protected using a spinlock as users of DSS HDMI
audio functionality might start/stop audio while holding a spinlock.
The mutex and the spinlock are held and released as needed by each
individual function to protect the panel state and the audio state.
Although the panel's audio_start functions does not check whether
the panel is active, the audio _ENABLED state can be reached only
from audio_enable, which does check the state of the panel. Also,
if the panel is ever disabled, the audio state will transition
to _DISABLED. Transitions are always protected by the audio lock.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Now that each output driver creates their own display devices, the
output drivers can also initialize those devices.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently the higher level omapdss platform driver gets the list of
displays in its platform data, and uses that list to create the
omap_dss_device for each display.
With DT, the logical way to do the above is to list the displays under
each individual output, i.e. we'd have "dpi" node, under which we would
have the display that uses DPI. In other words, each output driver
handles the displays that use that particular output.
To make the current code ready for DT, this patch modifies the output
drivers so that each of them creates the display devices which use that
output. However, instead of changing the platform data to suit this
method, each output driver is passed the full list of displays, and the
drivers pick the displays that are meant for them. This allows us to
keep the old platform data, and thus we avoid the need to change the
board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of having an ugly #ifdef mess in the core.c for creating debugfs
files, add a dss_debugfs_create_file() function that the dss drivers
can use to create the debugfs files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Initialize and uninitialize the output drivers by using arrays of
pointers to the init/uninit functions. This simplifies the code
slightly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the omapdss_core device is the parent for all other dss
devices, we don't need to use the dss_runtime_get/put anymore. Instead,
enabling omapdss_core will happen automatically when a child device is
enabled.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently have separate device/driver for each DSS HW module. The DPI
and SDI outputs are more or less parts of the DSS or DISPC hardware
modules, but in SW it makes sense to represent them as device/driver
pairs similarly to all the other outputs. This also makes sense for
device tree, as each node under dss will be a platform device, and
handling DPI & SDI somehow differently than the rest would just make the
code more complex.
This patch modifies the dpi.c and sdi.c to create drivers for the
platform devices.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
