Before adding forward-skbs to the coding buffer, the buffer is searched
for a potential coding opportunity. If one is found, the two packets are
network coded and transmitted right away. If not, the forward-skb is
added to the buffer.
Network coded packets are transmitted with information about the two
receivers and the two coded packets. The first receiver is given by the
MAC header, while the second is given in the payload/bat-header. The
second receiver uses promiscuous mode to receive the packet and check
the second destination.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.
In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <--- p2 ---- Node R Node B
4. Node A Node R ---- p1 ---> Node B
With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <- p1 x p2 - Node R - p1 x p2 -> Node B
The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:
Node A Node B
| \ / |
| p1 p2 |
| \ / |
p1 > Node R < p2
| |
| / \ |
| p1 x p2 p1 x p2 |
v / \ v
/ \
Node C < > Node D
More information is available on the open-mesh.org wiki[1].
This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.
[1] http://www.open-mesh.org/projects/batman-adv/wiki/Catwoman
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When processing the unregister notify for a hard interface, removing
the sysfs files may lead to a circular deadlock (rtnl mutex <->
s_active).
To overcome this problem, postpone the sysfs removal in a worker.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
When the Bridge Loop Avoidance component is not compiled-in, its boolean switch
should be not compiled as well. This patch surrounds the switch with a proper
ifdef.
This behaviour was introduced by 9fd6b0615b5499b270d39a92b8790e206cf75833
("batman-adv: add bridge loop avoidance compile option")
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Acked-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The current translation table mechanism is not suitable for multicast
addresses and we are currently flooding such frames anyway.
Therefore this patch prevents multicast MAC addresses being added to the
translation table.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ETH_P_BATMAN ethertype is now defined kernel-wide. Use it instead
of the private BATADV_ETH_P_BATMAN define.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The logic in the BLA mechanism may decide to drop broadcast packets
because the node may still be in the setup phase. For this reason,
further broadcast processing like the early client detection mechanism
must be done only after the BLA check.
This patches moves the invocation to BLA before any other broadcast
processing.
This was introduced 30cfd02b60
("batman-adv: detect not yet announced clients")
Reported-by: Glen Page <glen.page@thet.net>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
tt_poss_change is a node-wide flag which tells whether the node is in a roaming
state (a client recently moved to/away from it) in order to let it apply special
re-routing rules. However this flag does not give a clear idea of the current
state because it is not possible to understand *which client* is actually
involved in the roaming. For this reason a better approach has been chosen:
instead of using a node-wide variable, the roaming state is now given by a
per-tt_entry ROAM flag which, in case of packet coming through the node, tells
the node whether the real destination is in roaming state or not.
With this flag change, batadv_check_unicast_ttvn() has also been rearranged in
order to better fit the new re-routing logic and to be much more readable.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This patch adds a runtime switch that enables the user to turn the DAT feature
on or off at runtime
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In case of an ARP message going in or out the soft_iface, it is intercepted and
a special action is performed. In particular the DHT helper functions previously
implemented are used to store all the ARP entries belonging to the network in
order to provide a fast and unicast lookup instead of the classic broadcast
flooding mechanism.
Each node stores the entries it is responsible for (following the DHT rules) in
its soft_iface ARP table. This makes it possible to reuse the kernel data
structures and functions for ARP management.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The current unicast packet type does not contain the orig source address. This
patches add a new unicast packet (called UNICAST_4ADDR) which provides two new
fields: the originator source address and the subtype (the type of the data
contained in the packet payload). The former is useful to identify the node
which injected the packet into the network and the latter is useful to avoid
creating new unicast packet types in the future: a macro defining a new subtype
will be enough.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
We have seen this to break networks when used with bridge loop
avoidance. As we can't see any benefit from sending these ancient frames
via our mesh, we just drop them.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Transmissions over batman-adv devices always start another nested transmission
over devices attached to the batman-adv interface. These devices usually use
the ethernet lockdep class for the tx_queue lock which is also set by default
for all batman-adv devices. Lockdep will detect a nested locking attempt of two
locks with the same class and warn about a possible deadlock.
This is the default and expected behavior and should not alarm the locking
correctness prove mechanism. Therefore, the locks for all netdevice specific tx
queues get a special batman-adv lock class to avoid a false positive for each
transmission.
Reported-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
Into function interface_set_mac_addr, the function tt_local_add was
invoked before updating dev->dev_addr. The new MAC address was not
tagged as NoPurge.
Signed-off-by: Def <def@laposte.net>
In order to understand where a broadcast packet is coming from and use
this information to detect not yet announced clients, this patch modifies the
interface_rx() function by passing a new argument: the orig node
corresponding to the node that originated the received packet (if known).
This new argument if not NULL for broadcast packets only (other packets does not
have source field).
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The structure batadv_priv grows everytime a new feature is introduced. It gets
hard to find the parts of the struct that belongs to a specific feature. This
becomes even harder by the fact that not every feature uses a prefix in the
member name.
The variables for bridge loop avoidence, gateway handling, translation table
and visualization server are moved into separate structs that are included in
the bat_priv main struct.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the gateway functionality is used, some broadcast packets (DHCP
requests) may be transmitted as unicast packets. As the bridge loop
avoidance code now only considers the payload Ethernet destination,
it may drop the DHCP request for clients which are claimed by other
backbone gateways, because it falsely infers from the broadcast address
that the right backbone gateway should havehandled the broadcast.
Fix this by checking and delegating the batman-adv packet type used
for transmission.
Reported-by: Guido Iribarren <guidoiribarren@buenosaireslibre.org>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
The reserved fields in batman-adv packets are not set to a constant value. The
content of these memory regions is leaked unintentionally to the network.
This regression was introduced in 3b27ffb00f
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The "bat_" prefix in the source files implementing the batman-adv sysfs and
debugfs interface doesn't have a special meaning and are only used by these
files and files that implement the actual B.A.T.M.A.N. path finding algorithm.
The prefix is better suited to mark files that are used to implement the main
part of the path finding. All other files should not use it and therefore gets
renamed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
All non-static symbols of batman-adv were prefixed with batadv_ to avoid
collisions with other symbols of the kernel. Other symbols of batman-adv
should use the same prefix to keep the naming scheme consistent.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv doesn't follow the style for multiline comments that David S. Miller
prefers. All comments should be reformatted to follow this consistent style to
make the code slightly more readable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv can be compiled as part of the kernel instead of an module. In that
case the linker will see all non-static symbols of batman-adv and all other
non-static symbols of the kernel. This could lead to symbol collisions. A
prefix for the batman-adv symbols that defines their private namespace avoids
such a problem.
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Added additional counters in a bat_stats structure, which are exported
through the ethtool api. The counters are specific to batman-adv and
includes:
forwarded packets and bytes
management packets and bytes (aggregated OGMs at this point)
translation table packets
New counters are added by extending "enum bat_counters" in types.h and
adding corresponding descriptive string(s) to bat_counters_strings in
soft-iface.c.
Counters are increased by calling batadv_add_counter() and incremented
by one by calling batadv_inc_counter().
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Instead of using sizeof(struct ethhdr) it is strongly recommended to use the
kernel macro ETH_HLEN. This patch substitute each occurrence of the former
expressione with the latter one.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The define CONFIG_BATMAN_ADV_BLA switches the bridge loop avoidance
on - skip it, and the bridge loop avoidance is not compiled in.
This is useful if binary size should be saved or the feature is
not needed.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
This second version of the bridge loop avoidance for batman-adv
avoids loops between the mesh and a backbone (usually a LAN).
By connecting multiple batman-adv mesh nodes to the same ethernet
segment a loop can be created when the soft-interface is bridged
into that ethernet segment. A simple visualization of the loop
involving the most common case - a LAN as ethernet segment:
node1 <-- LAN --> node2
| |
wifi <-- mesh --> wifi
Packets from the LAN (e.g. ARP broadcasts) will circle forever from
node1 or node2 over the mesh back into the LAN.
With this patch, batman recognizes backbone gateways, nodes which are
part of the mesh and backbone/LAN at the same time. Each backbone
gateway "claims" clients from within the mesh to handle them
exclusively. By restricting that only responsible backbone gateways
may handle their claimed clients traffic, loops are effectively
avoided.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The functionality is to be replaced by an improved implementation,
so first clean up.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Remove dev_addr in interface_setup(), it's not needed anymore.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: use bitops, adapt to eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To increase readability the has_timed_out() functions has been introduced.
This patch converts existing time_after() calls to use this wrapper
function (if applicable).
This patch also converts all timeouts to miliseconds to be consistent.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
All batman-adv packets have a common 3 byte header. It can be used to share
some code between different code paths, but it was never explicit stated that
this header has to be always the same for all packets. Therefore, new code
changes always have the problem that they may accidently introduce regressions
by moving some elements around.
A new structure is introduced that contains the common header and makes it
easier visible that these 3 bytes have to be the same for all on-wire packets.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When entering softif_create(), the rtnl lock has already been acquired
by store_mesh_iface().
(store_mesh_iface() -> hardif_enable_interface() -> softif_create)
In case of an error, we should therefore call unregister_netdevice()
instead of unregister_netdev().
unregister_netdev() tries to acquire the rtnl lock itself and deadlocks
in this situation. unregister_netdevice() assumes that the rtnl lock
is already been held.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
corrects a critical bug of the GW feature. This bug made all the unicast
packets destined to a GW to be sent as broadcast. This bug is present even if
the sender GW feature is configured as OFF. It's an urgent bug fix and should
be committed as soon as possible.
This was a regression introduced by 43676ab590
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Removing unnecessary messages saves code and text.
Site specific OOM messages are duplications of a generic MM
out of memory message and aren't really useful, so just
delete them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
The follow-up routing code changes are going to introduce additional
routing packet types which make this distinction necessary.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
If a node has to send a packet issued by a WIFI client to another WIFI client,
the packet is dropped.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When a node receives a unicast packet it checks if the source and the
destination client can communicate or not due to the AP isolation
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Clients connected through a 802.11 device are now marked with the
TT_CLIENT_WIFI flag. This flag is also advertised with the tt
announcement.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Several typos have been corrected and some sentences have been rephrased
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Almost all of these have long outstayed their welcome.
And for every one of these macros, there are 10 features for which we
didn't add macros.
Let's just delete them all, and get out of habit of doing things this
way.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
In order to make possible to use the broadcast list for delayed sendings
the "delay" parameter is now provided instead of using 1 as hardcoded
value.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
If a client issues a DHCPREQUEST for renewal, the packet is dropped
if the old destination (the old gateway for the client) TQ is smaller
than the current best gateway TQ less GW_THRESHOLD
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
With the current client announcement implementation, in case of roaming,
an update is triggered on the new AP serving the client. At that point
the new information is spread around by means of the OGM broadcasting
mechanism. Until this operations is not executed, no node is able to
correctly route traffic towards the client. This obviously causes packet
drops and introduces a delay in the time needed by the client to recover
its connections.
A new packet type called ROAMING_ADVERTISEMENT is added to account this
issue.
This message is sent in case of roaming from the new AP serving the
client to the old one and will contain the client MAC address. In this
way an out-of-OGM update is immediately committed, so that the old node
can update its global translation table. Traffic reaching this node will
then be redirected to the correct destination utilising the fresher
information. Thus reducing the packet drops and the connection recovery
delay.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The client announcement mechanism informs every mesh node in the network
of any connected non-mesh client, in order to find the path towards that
client from any given point in the mesh.
The old implementation was based on the simple idea of appending a data
buffer to each OGM containing all the client MAC addresses the node is
serving. All other nodes can populate their global translation tables
(table which links client MAC addresses to node addresses) using this
MAC address buffer and linking it to the node's address contained in the
OGM. A node that wants to contact a client has to lookup the node the
client is connected to and its address in the global translation table.
It is easy to understand that this implementation suffers from several
issues:
- big overhead (each and every OGM contains the entire list of
connected clients)
- high latencies for client route updates due to long OGM trip time and
OGM losses
The new implementation addresses these issues by appending client
changes (new client joined or a client left) to the OGM instead of
filling it with all the client addresses each time. In this way nodes
can modify their global tables by means of "updates", thus reducing the
overhead within the OGMs.
To keep the entire network in sync each node maintains a translation
table version number (ttvn) and a translation table checksum. These
values are spread with the OGM to allow all the network participants to
determine whether or not they need to update their translation table
information.
When a translation table lookup is performed in order to send a packet
to a client attached to another node, the destination's ttvn is added to
the payload packet. Forwarding nodes can compare the packet's ttvn with
their destination's ttvn (this node could have a fresher information
than the source) and re-route the packet if necessary. This greatly
reduces the packet loss of clients roaming from one AP to the next.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
char was used in different places to store information without really
using the characteristics of that data type or by ignoring the fact that
char has not a well defined signedness.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
interface_tx is not used outside of soft-interface.c and thus doesn't
need to be declared inside soft-interface.h
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Usually rcu_dereference isn't necessary in situations were the
RCU-protected data structure cannot change, but sparse and lockdep still
need a similar functionality for analysis. rcu_dereference_protected
implements the reduced version which should be used to support the
dynamic and static analysis.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Documentation/CodingStyle recommends to use the form
p = kmalloc(sizeof(*p), ...);
to calculate the size of a struct and not the version where the struct
name is spelled out to prevent bugs when the type of p changes. This
also seems appropriate for manipulation of buffers when they are
directly associated with p.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
batman-adv uses pointers which are marked as const and should not
violate that type qualifier by passing it to functions which force a
cast to the non-const version.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
It is slightly irritating that comments after a long line span over
multiple lines without any code. It is easier to put them before the
actual code and reduce the number of lines which the eye has to read.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
To be coherent, all the functions/variables/constants have been renamed
to the TranslationTable style
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
hardif_list_lock is unneccessary because we already ensure that no
multiple admin operations can take place through rtnl_lock.
hardif_list_lock only adds additional overhead and complexity.
Critical functions now check whether they are called with rtnl_lock
using ASSERT_RTNL.
It indirectly fixes the problem that orig_hash_del_if() expects that
only one interface is deleted from hardif_list at a time, but
hardif_remove_interfaces() removes all at once and then calls
orig_hash_del_if().
Reported-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The bridge loop detection for batman-adv allows the bat0 interface
to be bridged into an ethernet segment which other batman-adv nodes
are connected to. In order to also allow multiple VLANs on top of
the bat0 interface to be bridged into the ethernet segment this
patch extends the aforementioned bridge loop detection.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The RCU callback softif_neigh_free_rcu() just calls kfree(), so we can
use kfree_rcu() instead of call_rcu().
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Marek Lindner <lindner_marek@yahoo.de>
Cc: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Sven Eckelmann <sven@narfation.org>
The rcu protected macros rcu_dereference() and rcu_assign_pointer()
for the bat_priv->primary_if need to be used, as well as spin/rcu locking.
Otherwise we might end up using a primary_if pointer pointing to already
freed memory.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like other virtual interfaces, e.g. br0, we don't need a transmit
queue. Packets should only be queued on real interfaces which are
underneath. In practice this patch makes little difference since the
virtual interfaces can accept packets as fast as they come, but the
patch will avoid bufferbloat questions to the mailling lists in the
future.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Add get/set wrapper functions for softif_neigh and
use rcu functions to manipulate the pointers.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When trying to associate a net_device with another net_device which
already exists, batman-adv assumes that this interface is a fully
initialized batman mesh interface without checking it. The behaviour
when accessing data behind netdev_priv of a random net_device is
undefined and potentially dangerous.
Reported-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
When printing the soft interface table the number of entries in the
softif neigh list are first being counted and a fitting buffer
allocated. After that the softif neigh list gets locked again and
the buffer printed - which has the following two issues:
For one thing, the softif neigh list might have grown when reacquiring
the rcu lock, which results in writing outside of the allocated buffer.
Furthermore 31 Bytes are not enough for printing an entry with a vid
of more than 2 digits.
The manual buffering is unnecessary, we can safely print to the seq
directly during the rcu_read_lock().
Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
It might be possible that 2 threads access the same data in the same
rcu grace period. The first thread calls call_rcu() to decrement the
refcount and free the data while the second thread increases the
refcount to use the data. To avoid this race condition all refcount
operations have to be atomic.
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Remove duplicate inclusion of "send.h" and "routing.h" from
net/batman-adv/soft-interface.c
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
types.h is included by main.h, which is included at the beginning of any
other c-file anyway. Therefore this commit removes those duplicate
inclussions.
Signed-off-by: Linus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
B.A.T.M.A.N. (better approach to mobile ad-hoc networking) is a routing
protocol for multi-hop ad-hoc mesh networks. The networks may be wired or
wireless. See http://www.open-mesh.org/ for more information and user space
tools.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
