Pull timers and timekeeping updates from Thomas Gleixner:
- Core infrastucture work for Y2038 to address the COMPAT interfaces:
+ Add a new Y2038 safe __kernel_timespec and use it in the core
code
+ Introduce config switches which allow to control the various
compat mechanisms
+ Use the new config switch in the posix timer code to control the
32bit compat syscall implementation.
- Prevent bogus selection of CPU local clocksources which causes an
endless reselection loop
- Remove the extra kthread in the clocksource code which has no value
and just adds another level of indirection
- The usual bunch of trivial updates, cleanups and fixlets all over the
place
- More SPDX conversions
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
clocksource/drivers/mxs_timer: Switch to SPDX identifier
clocksource/drivers/timer-imx-tpm: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Switch to SPDX identifier
clocksource/drivers/timer-imx-gpt: Remove outdated file path
clocksource/drivers/arc_timer: Add comments about locking while read GFRC
clocksource/drivers/mips-gic-timer: Add pr_fmt and reword pr_* messages
clocksource/drivers/sprd: Fix Kconfig dependency
clocksource: Move inline keyword to the beginning of function declarations
timer_list: Remove unused function pointer typedef
timers: Adjust a kernel-doc comment
tick: Prefer a lower rating device only if it's CPU local device
clocksource: Remove kthread
time: Change nanosleep to safe __kernel_* types
time: Change types to new y2038 safe __kernel_* types
time: Fix get_timespec64() for y2038 safe compat interfaces
time: Add new y2038 safe __kernel_timespec
posix-timers: Make compat syscalls depend on CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_COMPAT_32BIT_TIME
time: Introduce CONFIG_64BIT_TIME in architectures
compat: Enable compat_get/put_timespec64 always
...
Pull x86 RAS updates from Thomas Gleixner:
- Fix a stack out of bounds write in the MCE error injection code.
- Avoid IPIs during CPU hotplug to read the MCx_MISC block address from
a remote CPU. That's fragile and pointless because the block
addresses are the same on all CPUs. So they can be read once and
local.
- Add support for MCE broadcasting on newer VIA Centaur CPUs.
* 'ras-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/MCE/AMD: Read MCx_MISC block addresses on any CPU
x86/MCE: Fix stack out-of-bounds write in mce-inject.c: Flags_read()
x86/MCE: Enable MCE broadcasting on new Centaur CPUs
Pull irq updates from Thomas Gleixner:
- Consolidation of softirq pending:
The softirq mask and its accessors/mutators have many implementations
scattered around many architectures. Most do the same things
consisting in a field in a per-cpu struct (often irq_cpustat_t)
accessed through per-cpu ops. We can provide instead a generic
efficient version that most of them can use. In fact s390 is the only
exception because the field is stored in lowcore.
- Support for level!?! triggered MSI (ARM)
Over the past couple of years, we've seen some SoCs coming up with
ways of signalling level interrupts using a new flavor of MSIs, where
the MSI controller uses two distinct messages: one that raises a
virtual line, and one that lowers it. The target MSI controller is in
charge of maintaining the state of the line.
This allows for a much simplified HW signal routing (no need to have
hundreds of discrete lines to signal level interrupts if you already
have a memory bus), but results in a departure from the current idea
the kernel has of MSIs.
- Support for Meson-AXG GPIO irqchip
- Large stm32 irqchip rework (suspend/resume, hierarchical domains)
- More SPDX conversions
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
ARM: dts: stm32: Add exti support to stm32mp157 pinctrl
ARM: dts: stm32: Add exti support for stm32mp157c
pinctrl/stm32: Add irq_eoi for stm32gpio irqchip
irqchip/stm32: Add suspend/resume support for hierarchy domain
irqchip/stm32: Add stm32mp1 support with hierarchy domain
irqchip/stm32: Prepare common functions
irqchip/stm32: Add host and driver data structures
irqchip/stm32: Add suspend support
irqchip/stm32: Add falling pending register support
irqchip/stm32: Checkpatch fix
irqchip/stm32: Optimizes and cleans up stm32-exti irq_domain
irqchip/meson-gpio: Add support for Meson-AXG SoCs
dt-bindings: interrupt-controller: New binding for Meson-AXG SoC
dt-bindings: interrupt-controller: Fix the double quotes
softirq/s390: Move default mutators of overwritten softirq mask to s390
softirq/x86: Switch to generic local_softirq_pending() implementation
softirq/sparc: Switch to generic local_softirq_pending() implementation
softirq/powerpc: Switch to generic local_softirq_pending() implementation
softirq/parisc: Switch to generic local_softirq_pending() implementation
softirq/ia64: Switch to generic local_softirq_pending() implementation
...
Pull x86 dax updates from Ingo Molnar:
"This contains x86 memcpy_mcsafe() fault handling improvements the
nvdimm tree would like to make more use of"
* 'x86-dax-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm/memcpy_mcsafe: Define copy_to_iter_mcsafe()
x86/asm/memcpy_mcsafe: Add write-protection-fault handling
x86/asm/memcpy_mcsafe: Return bytes remaining
x86/asm/memcpy_mcsafe: Add labels for __memcpy_mcsafe() write fault handling
x86/asm/memcpy_mcsafe: Remove loop unrolling
Pull x86 debug updates from Ingo Molnar:
"This contains the x86 oops code printing reorganization and cleanups
from Borislav Betkov, with a particular focus in enhancing opcode
dumping all around"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/dumpstack: Explain the reasoning for the prologue and buffer size
x86/dumpstack: Save first regs set for the executive summary
x86/dumpstack: Add a show_ip() function
x86/fault: Dump user opcode bytes on fatal faults
x86/dumpstack: Add loglevel argument to show_opcodes()
x86/dumpstack: Improve opcodes dumping in the code section
x86/dumpstack: Carve out code-dumping into a function
x86/dumpstack: Unexport oops_begin()
x86/dumpstack: Remove code_bytes
Pull x86 cleanups from Ingo Molnar:
"Misc cleanups"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apm: Fix spelling mistake: "caculate" -> "calculate"
x86/mtrr: Rename main.c to mtrr.c and remove duplicate prefixes
x86: Remove pr_fmt duplicate logging prefixes
x86/early-quirks: Rename duplicate define of dev_err
x86/bpf: Clean up non-standard comments, to make the code more readable
Pull x86 build updates from Ingo Molnar:
"A handful of build system (Makefile, linker script) cleanups by
Masahiro Yamada"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/build/vdso: Put generated linker scripts to $(obj)/
x86/build/vdso: Remove unnecessary export in Makefile
x86/build/vdso: Remove unused $(vobjs-nox32) in Makefile
x86/build: Remove no-op macro VMLINUX_SYMBOL()
Pull x86 asm updates from Ingo Molnar:
- better support (non-atomic) 64-bit readq()/writeq() variants (Andy
Shevchenko)
- __clear_user() micro-optimization (Alexey Dobriyan)
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/io: Define readq()/writeq() to use 64-bit type
x86/asm/64: Micro-optimize __clear_user() - Use immediate constants
Trivial fix to spelling mistake in hmi_error_types text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Trivial fix to spelling mistake in bootx_printf message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull x86 boot updates from Ingo Molnar:
- Centaur CPU updates (David Wang)
- AMD and other CPU topology enumeration improvements and fixes
(Borislav Petkov, Thomas Gleixner, Suravee Suthikulpanit)
- Continued 5-level paging work (Kirill A. Shutemov)
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Mark __pgtable_l5_enabled __initdata
x86/mm: Mark p4d_offset() __always_inline
x86/mm: Introduce the 'no5lvl' kernel parameter
x86/mm: Stop pretending pgtable_l5_enabled is a variable
x86/mm: Unify pgtable_l5_enabled usage in early boot code
x86/boot/compressed/64: Fix trampoline page table address calculation
x86/CPU: Move x86_cpuinfo::x86_max_cores assignment to detect_num_cpu_cores()
x86/Centaur: Report correct CPU/cache topology
x86/CPU: Move cpu_detect_cache_sizes() into init_intel_cacheinfo()
x86/CPU: Make intel_num_cpu_cores() generic
x86/CPU: Move cpu local function declarations to local header
x86/CPU/AMD: Derive CPU topology from CPUID function 0xB when available
x86/CPU: Modify detect_extended_topology() to return result
x86/CPU/AMD: Calculate last level cache ID from number of sharing threads
x86/CPU: Rename intel_cacheinfo.c to cacheinfo.c
perf/events/amd/uncore: Fix amd_uncore_llc ID to use pre-defined cpu_llc_id
x86/CPU/AMD: Have smp_num_siblings and cpu_llc_id always be present
x86/Centaur: Initialize supported CPU features properly
Disassociate the exec_key from a VMA if the VMA permission is not
PROT_EXEC anymore. Otherwise the exec_only key continues to be
associated with the vma, causing unexpected behavior.
The problem was reported on x86 by Shakeel Butt, which is also
applicable on powerpc.
Fixes: 5586cf61e1 ("powerpc: introduce execute-only pkey")
Cc: stable@vger.kernel.org # v4.16+
Reported-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: Ram Pai <linuxram@us.ibm.com>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull perf updates from Ingo Molnar:
"Kernel side changes:
- x86 Intel uncore driver cleanups and enhancements (Kan Liang)
- group scheduling and other fixes (Song Liu
- store frame pointer in the sample traces for better profiling
(Alexey Budankov)
- compat fixes/enhancements (Eugene Syromiatnikov)
Tooling side changes, which you can build and install in a single step
via:
make -C tools/perf clean install
perf annotate:
- Support 'perf annotate --group' for non-explicit recorded event
"groups", showing multiple columns, one for each event, just like
when dealing with explicit event groups (those enclosed with {})
(Jin Yao)
- Record min/max LBR cycles (>= Skylake) and add 'perf annotate' TUI
hotkey to show it (c) (Jin Yao)
perf bpf:
- Add infrastructure to help in writing eBPF C programs to be used
with '-e name.c' type events in tools such as 'record' and 'trace',
with headers for common constructs and an examples directory that
will get populated as we add more such helpers and the 'perf bpf'
(Arnaldo Carvalho de Melo)
perf stat:
- Display time in precision based on std deviation (Jiri Olsa)
- Add --table option to display time of each run (Jiri Olsa)
- Display length strings of each run for --table option (Jiri Olsa)
perf buildid-cache:
- Add --list and --purge-all options (Ravi Bangoria)
perf test:
- Let 'perf test list' display subtests (Hendrik Brueckner)
perf pti:
- Create extra kernel maps to help in decoding samples in x86 PTI
entry trampolines (Adrian Hunter)
- Copy x86 PTI entry trampoline sections in the kcore copy used for
annotation and intel_pt CPU traces decoding (Adrian Hunter)
... and a lot of other fixes, enhancements and cleanups I did not
list, see the shortlog and git log for details"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
perf/x86/intel/uncore: Clean up client IMC uncore
perf/x86/intel/uncore: Expose uncore_pmu_event*() functions
perf/x86/intel/uncore: Support IIO free-running counters on SKX
perf/x86/intel/uncore: Add infrastructure for free running counters
perf/x86/intel/uncore: Add new data structures for free running counters
perf/x86/intel/uncore: Correct fixed counter index check in generic code
perf/x86/intel/uncore: Correct fixed counter index check for NHM
perf/x86/intel/uncore: Introduce customized event_read() for client IMC uncore
perf/x86: Store user space frame-pointer value on a sample
perf/core: Wire up compat PERF_EVENT_IOC_QUERY_BPF, PERF_EVENT_IOC_MODIFY_ATTRIBUTES
perf/core: Fix bad use of igrab()
perf/core: Fix group scheduling with mixed hw and sw events
perf kcore_copy: Amend the offset of sections that remap kernel text
perf kcore_copy: Copy x86 PTI entry trampoline sections
perf kcore_copy: Get rid of kernel_map
perf kcore_copy: Iterate phdrs
perf kcore_copy: Layout sections
perf kcore_copy: Calculate offset from phnum
perf kcore_copy: Keep a count of phdrs
perf kcore_copy: Keep phdr data in a list
...
Pull locking updates from Ingo Molnar:
- Lots of tidying up changes all across the map for Linux's formal
memory/locking-model tooling, by Alan Stern, Akira Yokosawa, Andrea
Parri, Paul E. McKenney and SeongJae Park.
Notable changes beyond an overall update in the tooling itself is the
tidying up of spin_is_locked() semantics, which spills over into the
kernel proper as well.
- qspinlock improvements: the locking algorithm now guarantees forward
progress whereas the previous implementation in mainline could starve
threads indefinitely in cmpxchg() loops. Also other related cleanups
to the qspinlock code (Will Deacon)
- misc smaller improvements, cleanups and fixes all across the locking
subsystem
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
locking/rwsem: Simplify the is-owner-spinnable checks
tools/memory-model: Add reference for 'Simplifying ARM concurrency'
tools/memory-model: Update ASPLOS information
MAINTAINERS, tools/memory-model: Update e-mail address for Andrea Parri
tools/memory-model: Fix coding style in 'lock.cat'
tools/memory-model: Remove out-of-date comments and code from lock.cat
tools/memory-model: Improve mixed-access checking in lock.cat
tools/memory-model: Improve comments in lock.cat
tools/memory-model: Remove duplicated code from lock.cat
tools/memory-model: Flag "cumulativity" and "propagation" tests
tools/memory-model: Add model support for spin_is_locked()
tools/memory-model: Add scripts to test memory model
tools/memory-model: Fix coding style in 'linux-kernel.def'
tools/memory-model: Model 'smp_store_mb()'
tools/memory-order: Update the cheat-sheet to show that smp_mb__after_atomic() orders later RMW operations
tools/memory-order: Improve key for SELF and SV
tools/memory-model: Fix cheat sheet typo
tools/memory-model: Update required version of herdtools7
tools/memory-model: Redefine rb in terms of rcu-fence
tools/memory-model: Rename link and rcu-path to rcu-link and rb
...
Pull EFI updates from Ingo Molnar:
- decode x86 CPER data (Yazen Ghannam)
- ignore unrealistically large option ROMs (Hans de Goede)
- initialize UEFI secure boot state during Xen dom0 boot (Daniel Kiper)
- additional minor tweaks and fixes.
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/capsule-loader: Don't output reset log when reset flags are not set
efi/x86: Ignore unrealistically large option ROMs
efi/x86: Fold __setup_efi_pci32() and __setup_efi_pci64() into one function
efi: Align efi_pci_io_protocol typedefs to type naming convention
efi/libstub/tpm: Make function efi_retrieve_tpm2_eventlog_1_2() static
efi: Decode IA32/X64 Context Info structure
efi: Decode IA32/X64 MS Check structure
efi: Decode additional IA32/X64 Bus Check fields
efi: Decode IA32/X64 Cache, TLB, and Bus Check structures
efi: Decode UEFI-defined IA32/X64 Error Structure GUIDs
efi: Decode IA32/X64 Processor Error Info Structure
efi: Decode IA32/X64 Processor Error Section
efi: Fix IA32/X64 Processor Error Record definition
efi/cper: Remove the INDENT_SP silliness
x86/xen/efi: Initialize UEFI secure boot state during dom0 boot
Pull RCU updates from Ingo Molnar:
- updates to the handling of expedited grace periods
- updates to reduce lock contention in the rcu_node combining tree
[ These are in preparation for the consolidation of RCU-bh,
RCU-preempt, and RCU-sched into a single flavor, which was
requested by Linus in response to a security flaw whose root cause
included confusion between the multiple flavors of RCU ]
- torture-test updates that save their users some time and effort
- miscellaneous fixes
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
rcu/x86: Provide early rcu_cpu_starting() callback
torture: Make kvm-find-errors.sh find build warnings
rcutorture: Abbreviate kvm.sh summary lines
rcutorture: Print end-of-test state in kvm.sh summary
rcutorture: Print end-of-test state
torture: Fold parse-torture.sh into parse-console.sh
torture: Add a script to edit output from failed runs
rcu: Update list of rcu_future_grace_period() trace events
rcu: Drop early GP request check from rcu_gp_kthread()
rcu: Simplify and inline cpu_needs_another_gp()
rcu: The rcu_gp_cleanup() function does not need cpu_needs_another_gp()
rcu: Make rcu_start_this_gp() check for out-of-range requests
rcu: Add funnel locking to rcu_start_this_gp()
rcu: Make rcu_start_future_gp() caller select grace period
rcu: Inline rcu_start_gp_advanced() into rcu_start_future_gp()
rcu: Clear request other than RCU_GP_FLAG_INIT at GP end
rcu: Cleanup, don't put ->completed into an int
rcu: Switch __rcu_process_callbacks() to rcu_accelerate_cbs()
rcu: Avoid __call_rcu_core() root rcu_node ->lock acquisition
rcu: Make rcu_migrate_callbacks wake GP kthread when needed
...
- A few time-related fixes:
- off-by-one calendar month on some classes of machines,
- Y2038 preparation,
- Build fix for ndelay() being called with a 64-bit type,
- Revive 64-bit get_user(), which is used by some Android code,
- Defconfig updates,
- Fix for a long-standing fatal bug in iounmap() on '020/030, which
was actually fixed in 2.4.23, but never in 2.5.x and later,
- Default DMA mask to avoid warning splats,
- Minor fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iF4EABYIAAYFAlsU83oACgkQisJQ/WRJ8XC+tAD/TC++gQlSUbz5ZSjZ95aGZl1O
nHjOHQpnae/R9pNFjogA/imtboTg7ukyx9Qnv7q47G8w7wGyxS+QHVTa6Hr2tEEF
=8PWk
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.18-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- a few time-related fixes:
- off-by-one calendar month on some classes of machines
- Y2038 preparation
- build fix for ndelay() being called with a 64-bit type
- revive 64-bit get_user(), which is used by some Android code
- defconfig updates
- fix for a long-standing fatal bug in iounmap() on '020/030, which was
actually fixed in 2.4.23, but never in 2.5.x and later
- default DMA mask to avoid warning splats
- minor fixes and cleanups
* tag 'm68k-for-v4.18-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Set default dma mask for platform devices
m68k/mm: Adjust VM area to be unmapped by gap size for __iounmap()
m68k/defconfig: Update defconfigs for v4.17-rc3
m68k/uaccess: Revive 64-bit get_user()
m68k: Implement ndelay() as an inline function to force type checking/casting
zorro: Add a blank line after declarations
m68k: Use read_persistent_clock64() consistently
m68k: Fix off-by-one calendar month
m68k: Fix style, spelling, and grammar in siginfo_build_tests()
m68k/mac: Fix SWIM memory resource end address
Pull siginfo updates from Eric Biederman:
"This set of changes close the known issues with setting si_code to an
invalid value, and with not fully initializing struct siginfo. There
remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64
and x86 to get the code that generates siginfo into a simpler and more
maintainable state. Most of that work involves refactoring the signal
handling code and thus careful code review.
Also not included is the work to shrink the in kernel version of
struct siginfo. That depends on getting the number of places that
directly manipulate struct siginfo under control, as it requires the
introduction of struct kernel_siginfo for the in kernel things.
Overall this set of changes looks like it is making good progress, and
with a little luck I will be wrapping up the siginfo work next
development cycle"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
signal/sh: Stop gcc warning about an impossible case in do_divide_error
signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions
signal/um: More carefully relay signals in relay_signal.
signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR}
signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code
signal/signalfd: Add support for SIGSYS
signal/signalfd: Remove __put_user from signalfd_copyinfo
signal/xtensa: Use force_sig_fault where appropriate
signal/xtensa: Consistenly use SIGBUS in do_unaligned_user
signal/um: Use force_sig_fault where appropriate
signal/sparc: Use force_sig_fault where appropriate
signal/sparc: Use send_sig_fault where appropriate
signal/sh: Use force_sig_fault where appropriate
signal/s390: Use force_sig_fault where appropriate
signal/riscv: Replace do_trap_siginfo with force_sig_fault
signal/riscv: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_fault where appropriate
signal/parisc: Use force_sig_mceerr where appropriate
signal/openrisc: Use force_sig_fault where appropriate
signal/nios2: Use force_sig_fault where appropriate
...
The RISC-V ISA defines a core set of performance counters that must
exist on all processors along with a standard way to add more
performance counters.
This patch set adds preliminary perf support for RISC-V systems. Long
term we'll move to model where all PMUs can be built into the kernel at
the same time, detected at runtime (possibly via device tree), and
provided to userspace. Since we currently only support the ISA-mandated
performance counters there's no need to detect anything right now.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
This patch provide a basic PMU, riscv_base_pmu, which supports two
general hardware event, instructions and cycles. Furthermore, this
PMU serves as a reference implementation to ease the portings in
the future.
riscv_base_pmu should be able to run on any RISC-V machine that
conforms to the Priv-Spec. Note that the latest qemu model hasn't
fully support a proper behavior of Priv-Spec 1.10 yet, but work
around should be easy with very small fixes. Please check
https://github.com/riscv/riscv-qemu/pull/115 for future updates.
Cc: Nick Hu <nickhu@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Signed-off-by: Alan Kao <alankao@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Pull aio updates from Al Viro:
"Majority of AIO stuff this cycle. aio-fsync and aio-poll, mostly.
The only thing I'm holding back for a day or so is Adam's aio ioprio -
his last-minute fixup is trivial (missing stub in !CONFIG_BLOCK case),
but let it sit in -next for decency sake..."
* 'work.aio-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
aio: sanitize the limit checking in io_submit(2)
aio: fold do_io_submit() into callers
aio: shift copyin of iocb into io_submit_one()
aio_read_events_ring(): make a bit more readable
aio: all callers of aio_{read,write,fsync,poll} treat 0 and -EIOCBQUEUED the same way
aio: take list removal to (some) callers of aio_complete()
aio: add missing break for the IOCB_CMD_FDSYNC case
random: convert to ->poll_mask
timerfd: convert to ->poll_mask
eventfd: switch to ->poll_mask
pipe: convert to ->poll_mask
crypto: af_alg: convert to ->poll_mask
net/rxrpc: convert to ->poll_mask
net/iucv: convert to ->poll_mask
net/phonet: convert to ->poll_mask
net/nfc: convert to ->poll_mask
net/caif: convert to ->poll_mask
net/bluetooth: convert to ->poll_mask
net/sctp: convert to ->poll_mask
net/tipc: convert to ->poll_mask
...
A piece of fixup code is currently shared by __copy_user and
__clear_user. It first disables the access to user-space memory
and then returns the "n" argument, which represents #(bytes not processed).
However,__copy_user's "n" is in register a2, while __clear_user's in a1,
and thus it causes errors for programs like setdomainname02 testcase in LTP.
This patch fixes this issue by separating their fixup code and returning
the right value for the kernel to handle a relative fault properly.
Signed-off-by: Alan Kao <alankao@andestech.com>
Cc: Greentime Hu <greentime@andestech.com>
Cc: Zong Li <zong@andestech.com>
Cc: Vincent Chen <vincentc@andestech.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
including:
- Extensive RST conversions and organizational work in the
memory-management docs thanks to Mike Rapoport.
- An update of Documentation/features from Andrea Parri and a script to
keep it updated.
- Various LICENSES updates from Thomas, along with a script to check SPDX
tags.
- Work to fix dangling references to documentation files; this involved a
fair number of one-liner comment changes outside of Documentation/
...and the usual list of documentation improvements, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----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=I6FG
-----END PGP SIGNATURE-----
Merge tag 'docs-4.18' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There's been a fair amount of work in the docs tree this time around,
including:
- Extensive RST conversions and organizational work in the
memory-management docs thanks to Mike Rapoport.
- An update of Documentation/features from Andrea Parri and a script
to keep it updated.
- Various LICENSES updates from Thomas, along with a script to check
SPDX tags.
- Work to fix dangling references to documentation files; this
involved a fair number of one-liner comment changes outside of
Documentation/
... and the usual list of documentation improvements, typo fixes, etc"
* tag 'docs-4.18' of git://git.lwn.net/linux: (103 commits)
Documentation: document hung_task_panic kernel parameter
docs/admin-guide/mm: add high level concepts overview
docs/vm: move ksm and transhuge from "user" to "internals" section.
docs: Use the kerneldoc comments for memalloc_no*()
doc: document scope NOFS, NOIO APIs
docs: update kernel versions and dates in tables
docs/vm: transhuge: split userspace bits to admin-guide/mm/transhuge
docs/vm: transhuge: minor updates
docs/vm: transhuge: change sections order
Documentation: arm: clean up Marvell Berlin family info
Documentation: gpio: driver: Fix a typo and some odd grammar
docs: ranoops.rst: fix location of ramoops.txt
scripts/documentation-file-ref-check: rewrite it in perl with auto-fix mode
docs: uio-howto.rst: use a code block to solve a warning
mm, THP, doc: Add document for thp_swpout/thp_swpout_fallback
w1: w1_io.c: fix a kernel-doc warning
Documentation/process/posting: wrap text at 80 cols
docs: admin-guide: add cgroup-v2 documentation
Revert "Documentation/features/vm: Remove arch support status file for 'pte_special'"
Documentation: refcount-vs-atomic: Update reference to LKMM doc.
...
- replaceme the force_dma flag with a dma_configure bus method.
(Nipun Gupta, although one patch is іncorrectly attributed to me
due to a git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few cleanups
to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
-----BEGIN PGP SIGNATURE-----
iQI/BAABCAApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAlsU1hwLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYPraxAAocC7JiFKW133/VugCtGA1x9uE8DPHealtsWTAeEq
KOOB3GxWMU2hKqQ4km5tcfdWoGJvvab6hmDXcitzZGi2JajO7Ae0FwIy3yvxSIKm
iH/ON7c4sJt8gKrXYsLVylmwDaimNs4a6xfODoCRgnWuovI2QrrZzupnlzPNsiOC
lv8ezzcW+Ay/gvDD/r72psO+w3QELETif/OzR/qTOtvLrVabM06eHmPQ8Wb98smu
/UPMMv6/3XwQnxpxpdyqN+p/gUdneXithzT261wTeZ+8gDXmcWBwHGcMBCimcoBi
FklW52moazIPIsTysqoNlVFsLGJTeS4p2D3BLAp5NwWYsLv+zHUVZsI1JY/8u5Ox
mM11LIfvu9JtUzaqD9SvxlxIeLhhYZZGnUoV3bQAkpHSQhN/xp2YXd5NWSo5ac2O
dch83+laZkZgd6ryw6USpt/YTPM/UHBYy7IeGGHX/PbmAke0ZlvA6Rae7kA5DG59
7GaLdwQyrHp8uGFgwze8P+R4POSk1ly73HHLBT/pFKnDD7niWCPAnBzuuEQGJs00
0zuyWLQyzOj1l6HCAcMNyGnYSsMp8Fx0fvEmKR/EYs8O83eJKXi6L9aizMZx4v1J
0wTolUWH6SIIdz474YmewhG5YOLY7mfe9E8aNr8zJFdwRZqwaALKoteRGUxa3f6e
zUE=
=6Acj
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- replace the force_dma flag with a dma_configure bus method. (Nipun
Gupta, although one patch is іncorrectly attributed to me due to a
git rebase bug)
- use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai)
- remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the
right thing for bounce buffering.
- move dma-debug initialization to common code, and apply a few
cleanups to the dma-debug code.
- cleanup the Kconfig mess around swiotlb selection
- swiotlb comment fixup (Yisheng Xie)
- a trivial swiotlb fix. (Dan Carpenter)
- support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt)
- add a new generic dma-noncoherent dma_map_ops implementation and use
it for arc, c6x and nds32.
- improve scatterlist validity checking in dma-debug. (Robin Murphy)
- add a struct device quirk to limit the dma-mask to 32-bit due to
bridge/system issues, and switch x86 to use it instead of a local
hack for VIA bridges.
- handle devices without a dma_mask more gracefully in the dma-direct
code.
* tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits)
dma-direct: don't crash on device without dma_mask
nds32: use generic dma_noncoherent_ops
nds32: implement the unmap_sg DMA operation
nds32: consolidate DMA cache maintainance routines
x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag
x86/pci-dma: remove the explicit nodac and allowdac option
x86/pci-dma: remove the experimental forcesac boot option
Documentation/x86: remove a stray reference to pci-nommu.c
core, dma-direct: add a flag 32-bit dma limits
dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs
dma-debug: check scatterlist segments
c6x: use generic dma_noncoherent_ops
arc: use generic dma_noncoherent_ops
arc: fix arc_dma_{map,unmap}_page
arc: fix arc_dma_sync_sg_for_{cpu,device}
arc: simplify arc_dma_sync_single_for_{cpu,device}
dma-mapping: provide a generic dma-noncoherent implementation
dma-mapping: simplify Kconfig dependencies
riscv: add swiotlb support
riscv: only enable ZONE_DMA32 for 64-bit
...
Add support for "VMWRITE to any supported field in the VMCS" and
enable this feature by default in L1's IA32_VMX_MISC MSR. If userspace
clears the VMX capability bit, the old behavior will be restored.
Note that this feature is a prerequisite for kvm in L1 to use VMCS
shadowing, once that feature is available.
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Disallow changes to the VMX capability MSRs while the vCPU is in VMX
operation. Although this does break the existing API, it helps to
avoid some potentially tricky situations for which there is no
architected behavior.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
'Commit d0659d946b ("KVM: x86: add option to advance tscdeadline
hrtimer expiration")' advances the tscdeadline (the timer is emulated
by hrtimer) expiration in order that the latency which is incurred
by hypervisor (apic_timer_fn -> vmentry) can be avoided. This patch
adds the advance tscdeadline expiration support to which the tscdeadline
timer is emulated by VMX preemption timer to reduce the hypervisor
lantency (handle_preemption_timer -> vmentry). The guest can also
set an expiration that is very small (for example in Linux if an
hrtimer feeds a expiration in the past); in that case we set delta_tsc
to 0, leading to an immediately vmexit when delta_tsc is not bigger than
advance ns.
This patch can reduce ~63% latency (~4450 cycles to ~1660 cycles on
a haswell desktop) for kvm-unit-tests/tscdeadline_latency when testing
busy waits.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nga/
-----END PGP SIGNATURE-----
Merge tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
- clean up how we pass around gfp_t and
blk_mq_req_flags_t (Christoph)
- prepare us to defer scheduler attach (Christoph)
- clean up drivers handling of bounce buffers (Christoph)
- fix timeout handling corner cases (Christoph/Bart/Keith)
- bcache fixes (Coly)
- prep work for bcachefs and some block layer optimizations (Kent).
- convert users of bio_sets to using embedded structs (Kent).
- fixes for the BFQ io scheduler (Paolo/Davide/Filippo)
- lightnvm fixes and improvements (Matias, with contributions from Hans
and Javier)
- adding discard throttling to blk-wbt (me)
- sbitmap blk-mq-tag handling (me/Omar/Ming).
- remove the sparc jsflash block driver, acked by DaveM.
- Kyber scheduler improvement from Jianchao, making it more friendly
wrt merging.
- conversion of symbolic proc permissions to octal, from Joe Perches.
Previously the block parts were a mix of both.
- nbd fixes (Josef and Kevin Vigor)
- unify how we handle the various kinds of timestamps that the block
core and utility code uses (Omar)
- three NVMe pull requests from Keith and Christoph, bringing AEN to
feature completeness, file backed namespaces, cq/sq lock split, and
various fixes
- various little fixes and improvements all over the map
* tag 'for-4.18/block-20180603' of git://git.kernel.dk/linux-block: (196 commits)
blk-mq: update nr_requests when switching to 'none' scheduler
block: don't use blocking queue entered for recursive bio submits
dm-crypt: fix warning in shutdown path
lightnvm: pblk: take bitmap alloc. out of critical section
lightnvm: pblk: kick writer on new flush points
lightnvm: pblk: only try to recover lines with written smeta
lightnvm: pblk: remove unnecessary bio_get/put
lightnvm: pblk: add possibility to set write buffer size manually
lightnvm: fix partial read error path
lightnvm: proper error handling for pblk_bio_add_pages
lightnvm: pblk: fix smeta write error path
lightnvm: pblk: garbage collect lines with failed writes
lightnvm: pblk: rework write error recovery path
lightnvm: pblk: remove dead function
lightnvm: pass flag on graceful teardown to targets
lightnvm: pblk: check for chunk size before allocating it
lightnvm: pblk: remove unnecessary argument
lightnvm: pblk: remove unnecessary indirection
lightnvm: pblk: return NVM_ error on failed submission
lightnvm: pblk: warn in case of corrupted write buffer
...
NX can set the 3rd bit in CR register for XER[SO] (Summary overflow)
which is not related to paste request. The current paste function
returns failure for a successful request when this bit is set. So mask
this bit and check the proper return status.
Fixes: 2392c8c8c0 ("powerpc/powernv/vas: Define copy/paste interfaces")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We don't need to share PVH GDT layout with other GDTs, especially
since we now have a PVH-speciific entry (for stack canary segment).
Define PVH's own selectors.
(As a side effect of this change we are also fixing improper
reference to __KERNEL_CS)
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
We are making calls to C code (e.g. xen_prepare_pvh()) which may use
stack canary (stored in GS segment).
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
There are no longer any platforms that use Marvell's mv64x60
hostbridges so remove the supporting kernel code.
CC: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are no longer any platforms that use Marvell's mv64x60
hostbridges so remove the supporting boot code.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are no longer any platforms that use Marvell's mv64x60's i2c
controller so remove its driver.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Mark Greer <<a href="mailto:mgreer@animalcreek.com">mgreer@animalcreek.com</a>><br>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are no longer any platforms that use Marvell's MPSC serial
controller so remove its driver.
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The C2K platform appears to be orphaned so remove code supporting it.
CC: Remi Machet <rmachet@nvidia.com>
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Acked-by: Remi Machet <remi@machet.us>
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
At the time being, memcmp() compares two chunks of memory
byte per byte.
This patch optimises the comparison by comparing word by word.
On the same way as commit 15c2d45d17 ("powerpc: Add 64bit
optimised memcmp"), this patch moves memcmp() into a dedicated
file named memcmp_32.S
A small benchmark performed on an 8xx comparing two chuncks
of 512 bytes performed 100000 times gives:
Before : 5852274 TB ticks
After: 1488638 TB ticks
This is almost 4 times faster
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rewrite clear_user() on the same principle as memset(0), making use
of dcbz to clear complete cache lines.
This code is a copy/paste of memset(), with some modifications
in order to retrieve remaining number of bytes to be cleared,
as it needs to be returned in case of error.
On the same way as done on PPC64 in commit 17968fbbd1
("powerpc: 64bit optimised __clear_user"), the patch moves
__clear_user() into a dedicated file string_32.S
On a MPC885, throughput is almost doubled:
Before:
~# dd if=/dev/zero of=/dev/null bs=1M count=1000
1048576000 bytes (1000.0MB) copied, 18.990779 seconds, 52.7MB/s
After:
~# dd if=/dev/zero of=/dev/null bs=1M count=1000
1048576000 bytes (1000.0MB) copied, 9.611468 seconds, 104.0MB/s
On a MPC8321, throughput is multiplied by 2.12:
Before:
root@vgoippro:~# dd if=/dev/zero of=/dev/null bs=1M count=1000
1048576000 bytes (1000.0MB) copied, 6.844352 seconds, 146.1MB/s
After:
root@vgoippro:~# dd if=/dev/zero of=/dev/null bs=1M count=1000
1048576000 bytes (1000.0MB) copied, 3.218854 seconds, 310.7MB/s
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
arch_vtime_task_switch() is a small function which is called
only from vtime_common_task_switch(), so it is worth inlining
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When compiled with GCC 8.1, vmlinux is significantly bigger than
with GCC 4.8.
When looking at the generated code with objdump, we notice that
all functions and loops when a 16 bytes alignment. This significantly
increases the size of the kernel. It is pointless and even
counterproductive as on the 8xx 'nop' also consumes one clock cycle.
Size of vmlinux with GCC 4.8:
text data bss dec hex filename
5801948 1626076 457796 7885820 7853fc vmlinux
Size of vmlinux with GCC 8.1:
text data bss dec hex filename
6764592 1630652 456476 8851720 871108 vmlinux
Size of vmlinux with GCC 8.1 and this patch:
text data bss dec hex filename
6331544 1631756 456476 8419776 8079c0 vmlinux
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Improve __csum_partial by interleaving loads and adds.
On a 8xx, it brings neither improvement nor degradation.
On a 83xx, it brings a 25% improvement.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
commit 87a156fb18 ("Align hot loops of some string functions")
degraded the performance of string functions by adding useless
nops
A simple benchmark on an 8xx calling 100000x a memchr() that
matches the first byte runs in 41668 TB ticks before this patch
and in 35986 TB ticks after this patch. So this gives an
improvement of approx 10%
Another benchmark doing the same with a memchr() matching the 128th
byte runs in 1011365 TB ticks before this patch and 1005682 TB ticks
after this patch, so regardless on the number of loops, removing
those useless nops improves the test by 5683 TB ticks.
Fixes: 87a156fb18 ("Align hot loops of some string functions")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use fault_in_pages_readable() to prefault user context
instead of open coding
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 885 familly processors don't have the Real Time Clock
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Variable div is set but never used. Remove it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
reloc_offset() is the same as add_reloc_offset(0)
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current implementation of from64to32() gives a poor result:
0000000000000270 <.from64to32>:
270: 38 00 ff ff li r0,-1
274: 78 69 00 22 rldicl r9,r3,32,32
278: 78 00 00 20 clrldi r0,r0,32
27c: 7c 60 00 38 and r0,r3,r0
280: 7c 09 02 14 add r0,r9,r0
284: 78 09 00 22 rldicl r9,r0,32,32
288: 7c 00 4a 14 add r0,r0,r9
28c: 78 03 00 20 clrldi r3,r0,32
290: 4e 80 00 20 blr
This patch modifies from64to32() to operate in the same
spirit as csum_fold()
It swaps the two 32-bit halves of sum then it adds it with the
unswapped sum. If there is a carry from adding the two 32-bit halves,
it will carry from the lower half into the upper half, giving us the
correct sum in the upper half.
The resulting code is:
0000000000000260 <.from64to32>:
260: 78 60 00 02 rotldi r0,r3,32
264: 7c 60 1a 14 add r3,r0,r3
268: 78 63 00 22 rldicl r3,r3,32,32
26c: 4e 80 00 20 blr
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
stale_map[] bits are only set in steal_context_smp() so
on UP processors this map is useless. Only manage it for SMP
processors.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
last_context is 16 on the 8xx, 65535 on the 47x and 255 on other ones.
The kernel is exclusively built for the 8xx, for the 47x or for
another processor so the last context can be defined as a constant
depending on the processor.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Reformat old comment]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
no_selective_tlbil hence the use of either steal_all_contexts()
or steal_context_up() depends on the subarch, it won't change
during run. Only the 8xx uses steal_all_contexts and CONFIG_PPC_8xx
is exclusive of other processors.
This patch replaces the test of no_selective_tlbil global var by
a test of CONFIG_PPC_8xx selection. It avoids the test and
removes unnecessary code.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
First context is now 1 for all supported platforms, so it
can be made a constant.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Direction is already checked in all calling functions in
include/linux/dma-mapping.h and also in called function __dma_sync()
So really no need to check it once more here.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
emulate_step() tests are failing if VSX is not supported or disabled.
emulate_step_test: lxvd2x : FAIL
emulate_step_test: stxvd2x : FAIL
If !CPU_FTR_VSX, emulate_step() failure is expected and testcase should
PASS with a valid justification. After patch:
emulate_step_test: lxvd2x : PASS (!CPU_FTR_VSX)
emulate_step_test: stxvd2x : PASS (!CPU_FTR_VSX)
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
emulate_step() is not checking runtime VSX feature flag before
emulating an instruction. This is causing kernel crash when kernel
is compiled with CONFIG_VSX=y but running on a machine where VSX
is not supported or disabled. Ex, while running emulate_step tests
on P6 machine:
Oops: Exception in kernel mode, sig: 4 [#1]
NIP [c000000000095c24] .load_vsrn+0x28/0x54
LR [c000000000094bdc] .emulate_loadstore+0x167c/0x17b0
Call Trace:
0x40fe240c7ae147ae (unreliable)
.emulate_loadstore+0x167c/0x17b0
.emulate_step+0x25c/0x5bc
.test_lxvd2x_stxvd2x+0x64/0x154
.test_emulate_step+0x38/0x4c
.do_one_initcall+0x5c/0x2c0
.kernel_init_freeable+0x314/0x4cc
.kernel_init+0x24/0x160
.ret_from_kernel_thread+0x58/0xb4
With fix:
emulate_step_test: lxvd2x : FAIL
emulate_step_test: stxvd2x : FAIL
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have barrier_nospec as mitigation so print it in
cpu_show_spectre_v1() when enabled.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Our syscall entry is done in assembly so patch in an explicit
barrier_nospec.
Based on a patch by Michal Suchanek.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Based on the x86 commit doing the same.
See commit 304ec1b050 ("x86/uaccess: Use __uaccess_begin_nospec()
and uaccess_try_nospec") and b3bbfb3fb5 ("x86: Introduce
__uaccess_begin_nospec() and uaccess_try_nospec") for more detail.
In all cases we are ordering the load from the potentially
user-controlled pointer vs a previous branch based on an access_ok()
check or similar.
Base on a patch from Michal Suchanek.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check what firmware told us and enable/disable the barrier_nospec as
appropriate.
We err on the side of enabling the barrier, as it's no-op on older
systems, see the comment for more detail.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Note that unlike RFI which is patched only in kernel the nospec state
reflects settings at the time the module was loaded.
Iterating all modules and re-patching every time the settings change
is not implemented.
Based on lwsync patching.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Based on the RFI patching. This is required to be able to disable the
speculation barrier.
Only one barrier type is supported and it does nothing when the
firmware does not enable it. Also re-patching modules is not supported
So the only meaningful thing that can be done is patching out the
speculation barrier at boot when the user says it is not wanted.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A no-op form of ori (or immediate of 0 into r31 and the result stored
in r31) has been re-tasked as a speculation barrier. The instruction
only acts as a barrier on newer machines with appropriate firmware
support. On older CPUs it remains a harmless no-op.
Implement barrier_nospec using this instruction.
mpe: The semantics of the instruction are believed to be that it
prevents execution of subsequent instructions until preceding branches
have been fully resolved and are no longer executing speculatively.
There is no further documentation available at this time.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This now has new code in it written by Nick and I, and switch to a
SPDX tag.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
This allows eg. the RCU stall detector, or the soft/hardlockup
detectors to trigger a backtrace on all CPUs.
We implement this by sending a "safe" NMI, which will actually only
send an IPI. Unfortunately the generic code prints "NMI", so that's a
little confusing but we can probably live with it.
If one of the CPUs doesn't respond to the IPI, we then print some info
from it's paca and do a backtrace based on its saved_r1.
Example output:
INFO: rcu_sched detected stalls on CPUs/tasks:
2-...0: (0 ticks this GP) idle=1be/1/4611686018427387904 softirq=1055/1055 fqs=25735
(detected by 4, t=58847 jiffies, g=58, c=57, q=1258)
Sending NMI from CPU 4 to CPUs 2:
CPU 2 didn't respond to backtrace IPI, inspecting paca.
irq_soft_mask: 0x01 in_mce: 0 in_nmi: 0 current: 3623 (bash)
Back trace of paca->saved_r1 (0xc0000000e1c83ba0) (possibly stale):
Call Trace:
[c0000000e1c83ba0] [0000000000000014] 0x14 (unreliable)
[c0000000e1c83bc0] [c000000000765798] lkdtm_do_action+0x48/0x80
[c0000000e1c83bf0] [c000000000765a40] direct_entry+0x110/0x1b0
[c0000000e1c83c90] [c00000000058e650] full_proxy_write+0x90/0xe0
[c0000000e1c83ce0] [c0000000003aae3c] __vfs_write+0x6c/0x1f0
[c0000000e1c83d80] [c0000000003ab214] vfs_write+0xd4/0x240
[c0000000e1c83dd0] [c0000000003ab5cc] ksys_write+0x6c/0x110
[c0000000e1c83e30] [c00000000000b860] system_call+0x58/0x6c
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Currently the options we have for sending NMIs are not necessarily
safe, that is they can potentially interrupt a CPU in a
non-recoverable region of code, meaning the kernel must then panic().
But we'd like to use smp_send_nmi_ipi() to do cross-CPU calls in
situations where we don't want to risk a panic(), because it doesn't
have the requirement that interrupts must be enabled like
smp_call_function().
So add an API for the caller to indicate that it wants to use the NMI
infrastructure, but doesn't want to do anything "unsafe".
Currently that is implemented by not actually calling cause_nmi_ipi(),
instead falling back to an IPI. In future we can pass the safe
parameter down to cause_nmi_ipi() and the individual backends can
potentially take it into account before deciding what to do.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
A CPU that gets stuck with interrupts hard disable can be difficult to
debug, as on some platforms we have no way to interrupt the CPU to
find out what it's doing.
A stop-gap is to have the CPU save it's stack pointer (r1) in its paca
when it hard disables interrupts. That way if we can't interrupt it,
we can at least trace the stack based on where it last disabled
interrupts.
In some cases that will be total junk, but the stack trace code should
handle that. In the simple case of a CPU that disable interrupts and
then gets stuck in a loop, the stack trace should be informative.
We could clear the saved stack pointer when we enable interrupts, but
that loses information which could be useful if we have nothing else
to go on.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
set_fs() sets the addr_limit, which is used in access_ok() to
determine if an address is a user or kernel address.
Some code paths use set_fs() to temporarily elevate the addr_limit so
that kernel code can read/write kernel memory as if it were user
memory. That is fine as long as the code can't ever return to
userspace with the addr_limit still elevated.
If that did happen, then userspace can read/write kernel memory as if
it were user memory, eg. just with write(2). In case it's not clear,
that is very bad. It has also happened in the past due to bugs.
Commit 5ea0727b16 ("x86/syscalls: Check address limit on user-mode
return") added a mechanism to check the addr_limit value before
returning to userspace. Any call to set_fs() sets a thread flag,
TIF_FSCHECK, and if we see that on the return to userspace we go out
of line to check that the addr_limit value is not elevated.
For further info see the above commit, as well as:
https://lwn.net/Articles/722267/https://bugs.chromium.org/p/project-zero/issues/detail?id=990
Verified to work on 64-bit Book3S using a POC that objdumps the system
call handler, and a modified lkdtm_CORRUPT_USER_DS() that doesn't kill
the caller.
Before:
$ sudo ./test-tif-fscheck
...
0000000000000000 <.data>:
0: e1 f7 8a 79 rldicl. r10,r12,30,63
4: 80 03 82 40 bne 0x384
8: 00 40 8a 71 andi. r10,r12,16384
c: 78 0b 2a 7c mr r10,r1
10: 10 fd 21 38 addi r1,r1,-752
14: 08 00 c2 41 beq- 0x1c
18: 58 09 2d e8 ld r1,2392(r13)
1c: 00 00 41 f9 std r10,0(r1)
20: 70 01 61 f9 std r11,368(r1)
24: 78 01 81 f9 std r12,376(r1)
28: 70 00 01 f8 std r0,112(r1)
2c: 78 00 41 f9 std r10,120(r1)
30: 20 00 82 41 beq 0x50
34: a6 42 4c 7d mftb r10
After:
$ sudo ./test-tif-fscheck
Killed
And in dmesg:
Invalid address limit on user-mode return
WARNING: CPU: 1 PID: 3689 at ../include/linux/syscalls.h:260 do_notify_resume+0x140/0x170
...
NIP [c00000000001ee50] do_notify_resume+0x140/0x170
LR [c00000000001ee4c] do_notify_resume+0x13c/0x170
Call Trace:
do_notify_resume+0x13c/0x170 (unreliable)
ret_from_except_lite+0x70/0x74
Performance overhead is essentially zero in the usual case, because
the bit is checked as part of the existing _TIF_USER_WORK_MASK check.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It's called 'fs' for historical reasons, it's named after the x86 'FS'
register. But we don't have to use that name for the member of
thread_struct, and in fact arch/x86 doesn't even call it 'fs' anymore.
So rename it to 'addr_limit', which better reflects what it's used
for, and is also the name used on other arches.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In PPC_PTRACE_GETHWDBGINFO and PPC_PTRACE_SETHWDEBUG we do an
access_ok() check and then __copy_{from,to}_user().
Instead we should just use copy_{from,to}_user() which does all that
for us and is less error prone.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The EEH report functions now share a fair bit of code around the start
and end of each function.
So factor out as much as possible, and move the traversal into a
custom function. This also allows accurate debug to be generated more
easily.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
[mpe: Format with clang-format]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If a device without a driver is recovered via EEH, the flag
EEH_DEV_NO_HANDLER is incorrectly left set on the device after
recovery, because the test in eeh_report_resume() for the existence of
a bound driver is done before the flag is cleared. If a driver is
later bound, and EEH experienced again, some of the drivers EEH
handers are not called.
To correct this, clear the flag unconditionally after EEH processing
is complete.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To ease future refactoring, extract calls to eeh_enable_irq() and
eeh_disable_irq() from the various report functions. This makes
the report functions initial sequences more similar, as well as making
the IRQ changes visible when reading eeh_handle_normal_event().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To ease future refactoring, extract setting of the channel state
from the report functions out into their own functions. This increases
the amount of code that is identical across all of the report
functions.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The same test is done in every EEH report function, so factor it out.
Since eeh_dev_removed() needs to be moved higher up in the file,
simplify it a little while we're at it.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a for_each-style macro for iterating through PEs without the
boilerplate required by a traversal function. eeh_pe_next() is now
exported, as it is now used directly in place.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As EEH event handling progresses, a cumulative result of type
pci_ers_result is built up by (some of) the eeh_report_*() functions
using either:
if (rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
if (*res == PCI_ERS_RESULT_NONE) *res = rc;
or:
if ((*res == PCI_ERS_RESULT_NONE) ||
(*res == PCI_ERS_RESULT_RECOVERED)) *res = rc;
if (*res == PCI_ERS_RESULT_DISCONNECT &&
rc == PCI_ERS_RESULT_NEED_RESET) *res = rc;
(Where *res is the accumulator.)
However, the intent is not immediately clear and the result in some
situations is order dependent.
Address this by assigning a priority to each result value, and always
merging to the highest priority. This renders the intent clear, and
provides a stable value for all orderings.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
[mpe: Minor formatting (clang-format)]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To aid debugging, add a message to show when EEH processing for a PE
will be done at the device's parent, rather than directly at the
device.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The traversal functions eeh_pe_traverse() and eeh_pe_dev_traverse()
both provide their first argument as void * but every single user casts
it to the expected type.
Change the type of the first parameter from void * to the appropriate
type, and clean up all uses.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Correct two cases where eeh_pcid_get() is used to reference the driver's
module but the reference is dropped before the driver pointer is used.
In eeh_rmv_device() also refactor a little so that only two calls to
eeh_pcid_put() are needed, rather than three and the reference isn't
taken at all if it wasn't needed.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a single log line at the end of successful EEH recovery, so that
it's clear that event processing has finished.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since thread-imc internally use the core-imc hardware infrastructure
and is depended on it, having thread-imc in the kernel in the
absence of core-imc is trivial. Patch disables thread-imc, if
core-imc is not registered.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace the direct return statement in imc_mem_init() with goto, to adhere
to the kernel coding style.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When any of the IMC (In-Memory Collection counter) devices fail
to initialize, imc_common_mem_free() frees set of memory. In doing so,
pmu_ptr pointer is also freed. But pmu_ptr pointer is used in subsequent
function (imc_common_cpuhp_mem_free()) which is wrong. Patch here reorders
the code to avoid such access.
Also free the memory which is dynamically allocated during imc
initialization, wherever required.
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The device node obtained with of_find_compatible_node() should be
released by calling of_node_put(). But it was not released when
of_get_property() failed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
[mpe: Invert the sense of the if so we only need one return path]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Structure platform_driver does not need to set the owner field, as this
will be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The GETFIELD and SETFIELD macros in xive-regs.h aren't used except for
a single instance of GETFIELD, so replace that and remove them.
These macros are also defined in vas.h, so either those should be
eventually replaced or the macros moved into bitops.h.
Signed-off-by: Russell Currey <ruscur@russell.cc>
[mpe: Rewrite the assignment to 'he' to avoid ffs() etc.]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
to_tm() is now completely unused, the only reference being in the
_dump_time() helper that is also unused. This removes both, leaving
the rest of the powerpc RTC code y2038 safe to as far as the hardware
supports.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
update_persistent_clock() is deprecated because it suffers from overflow
in 2038 on 32-bit architectures. This changes powerpc to use the
update_persistent_clock64() replacement, and to pass down 64-bit
timestamps consistently.
This is now simpler, as we no longer have to worry about the offset
numbers in tm_year and tm_mon that are different between the Linux
conventions and RTAS.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Looking through the remaining users of the deprecated mktime()
function, I found the powerpc rtc handlers, which use it in
place of rtc_tm_to_time64().
To clean this up, I'm changing over the read_persistent_clock()
function to the read_persistent_clock64() variant, and change
all the platform specific handlers along with it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The to_tm() helper function operates on a signed integer for the time,
so it will suffer from overflow in 2038, even on 64-bit kernels.
Rather than fix that function, this replaces its use in the rtas
procfs implementation with the standard rtc_time64_to_tm() helper
that is very similar but is not affected by the overflow.
In order to actually support long times, the parser function gets
changed to 64-bit user input and output as well. Note that the tm_mon
and tm_year representation is slightly different, so we have to manually
add an offset here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In order to use the rtc_tm_to_time64() and rtc_time64_to_tm()
helper functions in later patches, we have to ensure that
CONFIG_RTC_LIB is always built-in.
Note that this symbol only controls a couple of helper functions,
not the actual RTC subsystem, which remains optional and is
enabled with CONFIG_RTC_CLASS.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Needed on Amiga X1000 with SB600.
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When inserting SLB entries for EA above 512TB, we need to hard disable irq.
This will make sure we don't take a PMU interrupt that can possibly touch
user space address via a stack dump. To prevent this, we need to hard disable
the interrupt.
Also add a comment explaining why we don't need context synchronizing isync
with slbmte.
Fixes: f384796c4 ("powerpc/mm: Add support for handling > 512TB address in SLB miss")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With split pmd page table lock enabled, we don't use mm->page_table_lock when
updating pmd entries. This patch update hugetlb path to use the right lock
when inserting huge page directory entries into page table.
ex: if we are using hugepd and inserting hugepd entry at the pmd level, we
use pmd_lockptr, which based on config can be split pmd lock.
For update huge page directory entries itself we use mm->page_table_lock. We
do have a helper huge_pte_lockptr() for that.
Fixes: 675d99529 ("powerpc/book3s64: Enable split pmd ptlock")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently we do not have an isync, or any other context synchronizing
instruction prior to the slbie/slbmte in _switch() that updates the
SLB entry for the kernel stack.
However that is not correct as outlined in the ISA.
From Power ISA Version 3.0B, Book III, Chapter 11, page 1133:
"Changing the contents of ... the contents of SLB entries ... can
have the side effect of altering the context in which data
addresses and instruction addresses are interpreted, and in which
instructions are executed and data accesses are performed.
...
These side effects need not occur in program order, and therefore
may require explicit synchronization by software.
...
The synchronizing instruction before the context-altering
instruction ensures that all instructions up to and including that
synchronizing instruction are fetched and executed in the context
that existed before the alteration."
And page 1136:
"For data accesses, the context synchronizing instruction before the
slbie, slbieg, slbia, slbmte, tlbie, or tlbiel instruction ensures
that all preceding instructions that access data storage have
completed to a point at which they have reported all exceptions
they will cause."
We're not aware of any bugs caused by this, but it should be fixed
regardless.
Add the missing isync when updating kernel stack SLB entry.
Cc: stable@vger.kernel.org
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Flesh out change log with more ISA text & explanation]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The stores to update the SLB shadow area must be made as they appear
in the C code, so that the hypervisor does not see an entry with
mismatched vsid and esid. Use WRITE_ONCE for this.
GCC has been observed to elide the first store to esid in the update,
which means that if the hypervisor interrupts the guest after storing
to vsid, it could see an entry with old esid and new vsid, which may
possibly result in memory corruption.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When a single-threaded process has a non-local mm_cpumask, try to use
that point to flush the TLBs out of other CPUs in the cpumask.
An IPI is used for clearing remote CPUs for a few reasons:
- An IPI can end lazy TLB use of the mm, which is required to prevent
TLB entries being created on the remote CPU. The alternative is to
drop lazy TLB switching completely, which costs 7.5% in a context
switch ping-pong test betwee a process and kernel idle thread.
- An IPI can have remote CPUs flush the entire PID, but the local CPU
can flush a specific VA. tlbie would require over-flushing of the
local CPU (where the process is running).
- A single threaded process that is migrated to a different CPU is
likely to have a relatively small mm_cpumask, so IPI is reasonable.
No other thread can concurrently switch to this mm, because it must
have been given a reference to mm_users by the current thread before it
can use_mm. mm_users can be asynchronously incremented (by
mm_activate or mmget_not_zero), but those users must use remote mm
access and can't use_mm or access user address space. Existing code
makes the this assumption already, for example sparc64 has reset
mm_cpumask using this condition since the start of history, see
arch/sparc/kernel/smp_64.c.
This reduces tlbies for a kernel compile workload from 0.90M to 0.12M,
tlbiels are increased significantly due to the PID flushing for the
cleaning up remote CPUs, and increased local flushes (PID flushes take
128 tlbiels vs 1 tlbie).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Implementing pte_update with pte_xchg (which uses cmpxchg) is
inefficient. A single larx/stcx. works fine, no need for the less
efficient cmpxchg sequence.
Then remove the memory barriers from the operation. There is a
requirement for TLB flushing to load mm_cpumask after the store
that reduces pte permissions, which is moved into the TLB flush
code.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The ISA suggests ptesync after setting a pte, to prevent a table walk
initiated by a subsequent access from missing that store and causing a
spurious fault. This is an architectual allowance that allows an
implementation's page table walker to be incoherent with the store
queue.
However there is no correctness problem in taking a spurious fault in
userspace -- the kernel copes with these at any time, so the updated
pte will be found eventually. Spurious kernel faults on vmap memory
must be avoided, so a ptesync is put into flush_cache_vmap.
On POWER9 so far I have not found a measurable window where this can
result in more minor faults, so as an optimisation, remove the costly
ptesync from pte updates. If an implementation benefits from ptesync,
it would be better to add it back in update_mmu_cache, so it's not
done for things like fork(2).
fork --fork --exec benchmark improved 5.2% (12400->13100).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Prefetch the faulting address in update_mmu_cache to give the page
table walker perhaps 100 cycles head start as locks are dropped and
the interrupt completed.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This matches other architectures, when we know there will be no
further accesses to the address (e.g., for teardown), page table
entries can be cleared non-atomically.
The comments about NMMU are bogus: all MMU notifiers (including NMMU)
are released at this point, with their TLBs flushed. An NMMU access at
this point would be a bug.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the case of a spurious fault (which can happen due to a race with
another thread that changes the page table), the default Linux mm code
calls flush_tlb_page for that address. This is not required because
the pte will be re-fetched. Hash does not wire this up to a hardware
TLB flush for this reason. This patch avoids the flush for radix.
>From Power ISA v3.0B, p.1090:
Setting a Reference or Change Bit or Upgrading Access Authority
(PTE Subject to Atomic Hardware Updates)
If the only change being made to a valid PTE that is subject to
atomic hardware updates is to set the Refer- ence or Change bit to
1 or to add access authorities, a simpler sequence suffices
because the translation hardware will refetch the PTE if an access
is attempted for which the only problems were reference and/or
change bits needing to be set or insufficient access authority.
The nest MMU on POWER9 does not re-fetch the PTE after such an access
attempt before faulting, so address spaces with a coprocessor
attached will continue to flush in these cases.
This reduces tlbies for a kernel compile workload from 0.95M to 0.90M.
fork --fork --exec benchmark improved 0.5% (12300->12400).
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Radix flushes the TLB when updating ptes to increase permissiveness
of protection (increase access authority). Book3S does not require
TLB flushing in this case, and it is not done on hash. This patch
avoids the flush for radix.
>From Power ISA v3.0B, p.1090:
Setting a Reference or Change Bit or Upgrading Access Authority
(PTE Subject to Atomic Hardware Updates)
If the only change being made to a valid PTE that is subject to
atomic hardware updates is to set the Reference or Change bit to 1
or to add access authorities, a simpler sequence suffices because
the translation hardware will refetch the PTE if an access is
attempted for which the only problems were reference and/or change
bits needing to be set or insufficient access authority.
The nest MMU on POWER9 does not re-fetch the PTE after such an access
attempt before faulting, so address spaces with a coprocessor
attached will continue to flush in these cases.
This reduces tlbies for a kernel compile workload from 1.28M to 0.95M,
tlbiels from 20.17M 19.68M.
fork --fork --exec benchmark improved 2.77% (12000->12300).
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When relaxing access (read -> read_write update), pte needs to be marked invalid
to handle a nest MMU bug. We also need to do a tlb flush after the pte is
marked invalid before updating the pte with new access bits.
We also move tlb flush to platform specific __ptep_set_access_flags. This will
help us to gerid of unnecessary tlb flush on BOOK3S 64 later. We don't do that
in this patch. This also helps in avoiding multiple tlbies with coprocessor
attached.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In later patch, we use the vma and psize to do tlb flush. Do the prototype
update in separate patch to make the review easy.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In later patch we will update them which require them to be moved
to pgtable-radix.c. Keeping the function in radix.h results in
compile warning as below.
./arch/powerpc/include/asm/book3s/64/radix.h: In function ‘radix__ptep_set_access_flags’:
./arch/powerpc/include/asm/book3s/64/radix.h:196:28: error: dereferencing pointer to incomplete type ‘struct vm_area_struct’
struct mm_struct *mm = vma->vm_mm;
^~
./arch/powerpc/include/asm/book3s/64/radix.h:204:6: error: implicit declaration of function ‘atomic_read’; did you mean ‘__atomic_load’? [-Werror=implicit-function-declaration]
atomic_read(&mm->context.copros) > 0) {
^~~~~~~~~~~
__atomic_load
./arch/powerpc/include/asm/book3s/64/radix.h:204:21: error: dereferencing pointer to incomplete type ‘struct mm_struct’
atomic_read(&mm->context.copros) > 0) {
Instead of fixing header dependencies, we move the function to pgtable-radix.c
Also the function is now large to be a static inline . Doing the
move in separate patch helps in review.
No functional change in this patch. Only code movement.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In a later patch, we want to update __ptep_set_access_flags take page size
arg. This makes ptep_set_access_flags only work with mmu_virtual_psize.
To simplify the code make huge_ptep_set_access_flags directly call
__ptep_set_access_flags so that we can compute the hugetlb page size in
hugetlb function.
Now that ptep_set_access_flags won't be called for hugetlb remove
the is_vm_hugetlb_page() check and add the assert of pte lock
unconditionally.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The function removes the process element from NPU cache.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current implementation of TID allocation, using a global IDR, may
result in an errant process starving the system of available TIDs.
Instead, use task_pid_nr(), as mentioned by the original author. The
scenario described which prevented it's use is not applicable, as
set_thread_tidr can only be called after the task struct has been
populated.
In the unlikely event that 2 threads share the TID and are waiting,
all potential outcomes have been determined safe.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Switch the use of TIDR on it's CPU feature, rather than assuming it
is available based on architecture.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds a CPU feature bit to show whether the CPU has
the TIDR register available, enabling as_notify/wait in userspace.
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Using irq_work for processing OPAL event interrupts is not necessary.
irq_work is typically used to schedule work from NMI context, a
softirq may be more appropriate. However OPAL events are not
particularly performance or latency critical, so they can all be
invoked by kopald.
This patch removes the irq_work queueing, and instead wakes up
kopald when there is an event to be processed. kopald processes
interrupts individually, enabling irqs and calling cond_resched
between each one to minimise latencies.
Event handlers themselves should still use threaded handlers,
workqueues, etc. as necessary to avoid high interrupts-off latencies
within any single interrupt.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Although it is often possible to recover a CPU that was interrupted
from OPAL with a system reset NMI, it's undesirable to interrupt them
for a few reasons. Firstly because dump/debug code itself needs to
call firmware, so it could hang on a lock or possibly corrupt a
per-cpu data structure if it or another CPU was interrupted from
OPAL. Secondly, the kexec crash dump code will not return from
interrupt to unwind the OPAL call.
Call OPAL_QUIESCE with QUIESCE_HOLD before sending an NMI IPI to
another CPU, which wait for it to leave firmware (or time out) to
avoid this problem in normal conditions. Firmware bugs may still
result in a timeout and interrupting OPAL, but that is the best
option (stops the CPU, and possibly allows firmware to be debugged).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When the soft enabled flag was changed to a soft disable mask, xmon
and register dump code was not updated to reflect that, which is
confusing ('SOFTE: 1' previously meant interrupts were soft enabled,
currently it means the opposite, the general interrupt type has been
disabled).
Fix this by using the name irqmask, and printing it in hex.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When soft enabled was changed to irq disabled mask, this test missed
being converted (although the equivalent book3s test was converted).
The PMU drivers consider it an NMI when they take a PMI while general
interrupts are disabled. This change restores that behaviour.
Fixes: 01417c6cc7 ("powerpc/64: Change soft_enabled from flag to bitmask")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
These are not local timer interrupts but IPIs. It's good to be able
to see how timer offloading is behaving, so split these out into
their own category.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Large decrementers (e.g., POWER9) can take a very long time to wrap,
so when the timer iterrupt handler sets the decrementer to max so as
to avoid taking another decrementer interrupt when hard enabling
interrupts before running timers, it effectively disables the soft
NMI coverage for timer interrupts.
Fix this by using the traditional 31-bit value instead, which wraps
after a few seconds. masked interrupt code does the same thing, and
in normal operation neither of these paths would ever wrap even the
31 bit value.
Note: the SMP watchdog should catch timer interrupt lockups, but it
is preferable for the local soft-NMI to catch them, mainly to avoid
the IPI.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The broadcast tick recipient can call tick_receive_broadcast rather
than re-running the full timer interrupt.
It does not have to check for the next event time, because the sender
already determined the timer has expired. It does not have to test
irq_work_pending, because that's a direct decrementer interrupt and
does not go through the clock events subsystem. And it does not have
to read PURR because that was removed with the previous patch.
This results in no code size change, but both the decrementer and
broadcast path lengths are reduced.
Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For SPLPAR, lparcfg provides a sum of PURR registers for all CPUs.
Currently this is done by reading PURR in context switch and timer
interrupt, and storing that into a per-CPU variable. These are summed
to provide the value.
This does not work with all timer schemes (e.g., NO_HZ_FULL), and it
is sub-optimal for performance because it reads the PURR register on
every context switch, although that's been difficult to distinguish
from noise in the contxt_switch microbenchmark.
This patch implements the sum by calling a function on each CPU, to
read and add PURR values of each CPU.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Book3S minimum supported ISA version now requires mtmsrd L=1. This
instruction does not require bits other than RI and EE to be supplied,
so __hard_irq_enable() and __hard_irq_disable() does not have to read
the kernel_msr from paca.
Interrupt entry code already relies on L=1 support.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This check does not catch IRQ soft mask bugs, but this option is
slightly more suitable than TRACE_IRQFLAGS.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
irq_work_raise should not cause a decrementer exception unless it is
called from NMI context. Doing so often just results in an immediate
masked decrementer interrupt:
<...>-550 90d... 4us : update_curr_rt <-dequeue_task_rt
<...>-550 90d... 5us : dbs_update_util_handler <-update_curr_rt
<...>-550 90d... 6us : arch_irq_work_raise <-irq_work_queue
<...>-550 90d... 7us : soft_nmi_interrupt <-soft_nmi_common
<...>-550 90d... 7us : printk_nmi_enter <-soft_nmi_interrupt
<...>-550 90d.Z. 8us : rcu_nmi_enter <-soft_nmi_interrupt
<...>-550 90d.Z. 9us : rcu_nmi_exit <-soft_nmi_interrupt
<...>-550 90d... 9us : printk_nmi_exit <-soft_nmi_interrupt
<...>-550 90d... 10us : cpuacct_charge <-update_curr_rt
The soft_nmi_interrupt here is the call into the watchdog, due to the
decrementer interrupt firing with irqs soft-disabled. This is
harmless, but sub-optimal.
When it's not called from NMI context or with interrupts enabled, mark
the decrementer pending in the irq_happened mask directly, rather than
having the masked decrementer interupt handler do it. This will be
replayed at the next local_irq_enable. See the comment for details.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When IODA2 creates a PE, it creates an IOMMU table with it_ops::free
set to pnv_ioda2_table_free() which calls pnv_pci_ioda2_table_free_pages().
Since iommu_tce_table_put() calls it_ops::free when the last reference
to the table is released, explicit call to pnv_pci_ioda2_table_free_pages()
is not needed so let's remove it.
This should fix double free in the case of PCI hotuplug as
pnv_pci_ioda2_table_free_pages() does not reset neither
iommu_table::it_base nor ::it_size.
This was not exposed by SRIOV as it uses different code path via
pnv_pcibios_sriov_disable().
IODA1 does not inialize it_ops::free so it does not have this issue.
Fixes: c5f7700bbd ("powerpc/powernv: Dynamically release PE")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
match_string() returns the index of an array for a matching string,
which can be used instead of open coded variant.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
GCC 8.1 emits warnings such as the following. As arch/powerpc code is
built with -Werror, this breaks the build with GCC 8.1.
In file included from arch/powerpc/kernel/pci_64.c:23:
./include/linux/syscalls.h:233:18: error: 'sys_pciconfig_iobase' alias
between functions of incompatible types 'long int(long int, long
unsigned int, long unsigned int)' and 'long int(long int, long int,
long int)' [-Werror=attribute-alias]
asmlinkage long sys##name(__MAP(x,__SC_DECL,__VA_ARGS__)) \
^~~
./include/linux/syscalls.h:222:2: note: in expansion of macro '__SYSCALL_DEFINEx'
__SYSCALL_DEFINEx(x, sname, __VA_ARGS__)
This patch inhibits those warnings.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Trim change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
GCC 8.1 warns about possible string truncation:
arch/powerpc/kernel/nvram_64.c:1042:2: error: 'strncpy' specified
bound 12 equals destination size [-Werror=stringop-truncation]
strncpy(new_part->header.name, name, 12);
arch/powerpc/platforms/ps3/repository.c:106:2: error: 'strncpy'
output truncated before terminating nul copying 8 bytes from a
string of the same length [-Werror=stringop-truncation]
strncpy((char *)&n, text, 8);
Fix it by using memcpy(). To make that safe we need to ensure the
destination is pre-zeroed. Use kzalloc() in the nvram code and
initialise the u64 to zero in the ps3 code.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Use kzalloc() in the nvram code, flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This is a branch with a mixture of mm, x86 and powerpc commits all
relating to some minor cross-arch pkeys consolidation. The x86/mm
changes have been reviewed by Ingo & Dave Hansen and the tree has been
in linux-next for some weeks without issue.
We ended up with an ugly conflict between fixes and next in ftrace.h
involving multiple nested ifdefs, and the automatic resolution is
wrong. So merge fixes into next so we can fix it up.
A final few MIPS fixes for 4.17:
- Drop Lantiq gphy reboot/remove reset (4.14)
- prctl(PR_SET_FP_MODE): Disallow PRE without FR (4.0)
- ptrace(PTRACE_PEEKUSR): Fix 64-bit FGRs (3.15)
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS7lRNBWUYtqfDOVL41zuSGKxAj8gUCWxHFOwAKCRA1zuSGKxAj
8i39AQCX9phkffpRDnA1e/MiGGeRZ5+f9FBOzuS1x2nzdUagoQD9FzWxdcx57Syj
ye0kUtmc/wm8U6kz3qC3OInSeVuIEQg=
=3NGM
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_4.17_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from James Hogan:
"A final few MIPS fixes for 4.17:
- drop Lantiq gphy reboot/remove reset (4.14)
- prctl(PR_SET_FP_MODE): Disallow PRE without FR (4.0)
- ptrace(PTRACE_PEEKUSR): Fix 64-bit FGRs (3.15)"
* tag 'mips_fixes_4.17_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: ptrace: Fix PTRACE_PEEKUSR requests for 64-bit FGRs
MIPS: prctl: Disallow FRE without FR with PR_SET_FP_MODE requests
MIPS: lantiq: gphy: Drop reboot/remove reset asserts
This is to avoid potential merging conflicts between commit 55e3748e89
("arm64: KVM: Add ARCH_WORKAROUND_2 support for guests") and the KVM
tree.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
* R-Mobile A1 (r8a7740) SoC
- Describe CEU, IRQC, SYS-DMAC and USB devices
- Cleanup for consistency with other Renesas SoCs and enhanced maintainability
+ Stop grouping clocks under a "clocks" subnode
+ Add soc node
+ Sort subnodes of root and soc nodes
* RZ/A1H (r7s72100) SoC
- Describe CEU device
* R-Car Gen2, RZ/G1 and RZ/A1H SoCs
- Add PMU device nodes
Geert Uytterhoeven says: "This patch series enables support for the ARM
Performance Monitor Units in Cortex-A7, Cortex-A9, and Cortex-A15 CPU
cores on Renesas RZ/A1, R-Car Gen2, and RZ/G1 SoCs. This allows for
better performance analysis using the "perf" tool."
* RZ/A1H (r7s72100) SoC
- Correct interrupt types
Geert Uytterhoeven says "RZ/A1H peripherals use a mix of level and edge
interrupts.
This patch series corrects the interrupt types for watchdog and RTC from
edge to level, to match the datasheet."
* R-Mobile APE6 (r8a73a4) APE4EVM board and SH-Mobile AG5 (sh73a0) SoC
- Use generic disable-wp instead of now deprecated
toshiba,mmc-wrprotect-disable property
* EMMA Mobile EV2 (emev2) and SH-Mobile AG5 (sh73a0) SoCs
- Add missing interrupt-affinity to PMU
Geert Uytterhoeven says "The Cortex-A9 PMU nodes on SH-Mobile AG5 and
Emma Mobile EV2 reference two interrupts, but lack interrupt-affinity
properties, leading to:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
This series adds the missing properties to fix this."
* R-Car H2 (r8a7790) and R-Mobile APE6 (r8a73a4) SoCs
- Correct mask for GIC PPI interrupts
Geert Uytterhoeven says "R-Car H2 and R-Mobile APE6 contain four
Cortex-A15 and four Cortex-A7 cores, hence the second interrupt
specifier cell for Private Peripheral Interrupts should use
"GIC_CPU_MASK_SIMPLE(8)", to make sure interrupts can be delivered to
all 8 processor cores.
This brings the predecessors of R-Car Gen3 in line with what we're
doing on other big.LITTLE SoCs, like R-Car H3 and M3-W."
* Alt board for R-Car E2 (r8a7794) SoC
* RBoards for -Car Gen2 SoCs and kzm9d board for EMMA Mobile EV2 (emev2) SoC
- Drop unnecessary address properties from VIN port nodes
These are unnecessary as the nodes to not have bus addresses.
* R-Car H2 (r8a7790), M2-W (r8a7791), M2-N (r8a7793) and E2 (r8a7794) SoCs
- Describe FDP1 instances
* iW-RainboW-G23S board for RZ/G1C (r8a77470) SoC
- Initial SoC and board support
- Enable EtherAVB
- Describe all SCIF devices
* Boards for R-Car Gen2 SoCs
- Enable watchdog support
Geert Uytterhoeven says "This patch series enables the builtin watchdog
timer on R-Car Gen2 SoCs on all supported boards, and builds on top of
Fabrizio's "[RFC v4 00/26] Fix watchdog on Renesas R-Car Gen2 and
RZ/G1"."
* R-Car Gen2 and RZ/G1 SoCs
- Describe watchdog devices
- For R-Car Gen2 this involves updating the SMP routine side as
it is changed by a driver updated to allow watchdog device support
* Wheat board for V2H (r8a7792) SoC
- Correct ADV7513 address usage
Kieran Bingham says "The r8a7792 Wheat board has two ADV7513 devices
sharing a single I2C bus, however in low power mode the ADV7513 will
reset it's slave maps to use the hardware defined default addresses.
The ADV7511 driver was adapted to allow the two devices to be
registered correctly - but it did not take into account the fault
whereby the devices reset the addresses.
This results in an address conflict between the device using the
default addresses, and the other device if it is in low-power-mode.
Repair this issue by moving both devices away from the default address
definitions."
-----BEGIN PGP SIGNATURE-----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=LV2P
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/late
Renesas ARM Based SoC DT Updates for v4.18
* R-Mobile A1 (r8a7740) SoC
- Describe CEU, IRQC, SYS-DMAC and USB devices
- Cleanup for consistency with other Renesas SoCs and enhanced maintainability
* RZ/A1H (r7s72100) SoC
- Describe CEU device
* R-Car Gen2, RZ/G1 and RZ/A1H SoCs
- Add PMU device nodes
* RZ/A1H (r7s72100) SoC
- Correct interrupt types
* R-Mobile APE6 (r8a73a4) APE4EVM board and SH-Mobile AG5 (sh73a0) SoC
- Use generic disable-wp instead of now deprecated
toshiba,mmc-wrprotect-disable property
* EMMA Mobile EV2 (emev2) and SH-Mobile AG5 (sh73a0) SoCs
- Add missing interrupt-affinity to PMU
* R-Car H2 (r8a7790) and R-Mobile APE6 (r8a73a4) SoCs
- Correct mask for GIC PPI interrupts
* R-Car H2 (r8a7790), M2-W (r8a7791), M2-N (r8a7793) and E2 (r8a7794) SoCs
- Describe FDP1 instances
* R-Car Gen2 and RZ/G1 SoCs
- Describe watchdog devices
- For R-Car Gen2 this involves updating the SMP routine side as
it is changed by a driver updated to allow watchdog device support
* Alt board for R-Car E2 (r8a7794) SoC
* RBoards for -Car Gen2 SoCs and kzm9d board for EMMA Mobile EV2 (emev2) SoC
* iW-RainboW-G23S board for RZ/G1C (r8a77470) SoC
- Initial SoC and board support
- Enable EtherAVB
- Describe all SCIF devices
* Boards for R-Car Gen2 SoCs
- Enable watchdog support
* Wheat board for V2H (r8a7792) SoC
- Correct ADV7513 address usage
* tag 'renesas-dt-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (69 commits)
ARM: dts: r8a7740: Add CEU1
ARM: dts: r8a7740: Add CEU0
ARM: dts: r8a7745: Add PMU device node
ARM: dts: r8a7743: Add PMU device node
ARM: dts: r8a7794: Add PMU device node
ARM: dts: r8a7793: Add PMU device node
ARM: dts: r8a7792: Add PMU device node
ARM: dts: r8a7791: Add PMU device node
ARM: dts: r8a7790: Add PMU device nodes
ARM: dts: r7s72100: Add PMU device node
ARM: dts: r7s72100: Correct RTC interrupt types
ARM: dts: r7s72100: Correct watchdog timer interrupt type
ARM: dts: emev2: Add missing interrupt-affinity to PMU node
ARM: dts: sh73a0: Add missing interrupt-affinity to PMU node
ARM: dts: r8a73a4: Correct mask for GIC PPI interrupts
ARM: dts: r8a7790: Correct mask for GIC PPI interrupts
ARM: shmobile: r8a7794: alt: add EEPROM to DTS
ARM: dts: kzm9d: Drop unnecessary address properties from gpio_keys node
ARM: dts: silk: Drop unnecessary address properties from vin port node
ARM: dts: alt: Drop unnecessary address properties from vin port node
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Cleanups:
- Corresct whitespace
- sort subnodes of the root and soc nodes
* R-Car M3-N (r8a77965) SoC
- Describe MSIOF SPI, PWM, SDHI and I2C devices in DT
- Add thermal support
* R-Car H3 (r8a7795) and R-Car M3-W (r8a7796) SoCs
- Decrease temperature hysteresis
Niklas Söderlund says "... decrease the hysteresis from 2C to 1C for
the two boards we have described upstream. They have no dependencies
and are ready to be accepted if the review is in favor of them."
* R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs
- Add address properties to rcar_sound port nodes
The rcar_sound port nodes have unit names and thus should have register
properties.
* R-Car H3 (r8a7795), M3-W (r8a7796) V3M (r8a77970) and D3 (r8a77995) SoCs
- Enable IPMMU devices
Magnus Damm says "Following the policy of using DT to describe the
hardware and not software support state, this series makes sure all
IPMMU devices are enabled in DT for SoCs such as r8a7795, r8a7796,
r8a77970 and r8a77995."
* R-Car M3-N (r8a77965) and V3H (r8a77980) SoCs
- Use sysc binding macros
These can be used now that they are present in Linus's tree.
This is a simple replacement of numeric values with symbolic ones.
- Describe USB2 and USB3 devices in DT
* R-Car V3M (r8a77970) SoC
- Add SMP Support
Geert Uytterhoeven says "This patch series enables SMP support on the
R-Car V3M SoC, by adding the second Cortex-A53 CPU core. It also adds
the performance monitor unit, and links it to both CPU cores."
- Correct IPMMU DS1 bit number
Magnus Damm says "Judging by "R-Car-Gen3-rev0.80" IPMMU IMSSTR register
documentation for [R-Car V3M] the DS1 bit field should be bit 0."
* R-Car V3H (r8a77980) SoC
- Use CPG clock binding macros
These can be used now that they are present in Linus's tree.
This is a simple replacement of numeric values with symbolic ones.
* R-Car V3H (r8a77980) and V3M (r8a77970) SoCs
- Disable EtherAVB
Sergei Shtylov says "I'm fixing the issue in the EtherAVB device nodes
in the R8A779{7|8}0 device trees that missed the "status" prop, usually
disabling the SoC devices in anticipation that the board device trees
enable the devices according to their needs. There should be no issues
with the current R8A779{7|8}0 board device trees, as all of them use
EtherAVB anyway, so I'm sending the patches generated against the
'devel' branch..."
* R-Car D3 (r8a77995) SoC
- Describe VIN4 in DT
* Ebisu board with R-Car E3 (r8a77990) SoC
- Initial support:
+ PSCI
+ CPU (single)
+ Cache controller
+ Main clocks and controller
+ Interrupt controller
+ Timer
+ PMU
+ Reset controller
+ Product register
+ System controller
+ UART for console
* Salvator-XS boards with R-Car H3 (r8a7795) SoC
- Enable USB2.0 channel 3
* Salvator-X and Salvator-XS boards with M3-N (r8a77965) SoC
- Enable DU
Kieran Bingham "This series enables the DU for the M3-N R8A77965 SoC,
and provides output on the VGA and HDMI connectors.
LVDS is not yet supported or tested."
* Salvator-X and Salvator-XS boards with
R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs
- Enable nable VIN, CSI-2 and ADV7482
Niklas Söderlund says "This series enable capture for H3, M3-W, M3-N
Salvator-X and Salvator-XS boards. It also adds the VIN and CSI-2 nodes
for V3M, but as the ADV7482 is on the V3M expansion boards I have
chosen not include that enablement in this series."
- Add PMIC DDR Backup Power config
Geert Uytterhoeven says " The ROHM BD9571MWV PMIC on the Renesas
Salvator-X(S) and ULCB development boards supports DDR Backup Power,
which means that the DDR power rails can be kept powered while the main
SoC is powered down.
For this to function correctly, the DDR Backup Power configuration
must be described in DT, which is the topic of this series:
- The first patch adds the missing device node for the BD9571 PMIC on
the ULCB boards,
- The last two patches add DDR Backup Mode configuration for
Salvator-X(S) and ULCB."
- Add EEPROM
Wolfram Sang says "Add the EEPROM found on Salvator-X and -XS boards
for H3, M3-W, and M3-N on the IIC_DVFS bus."
- Enable HDMI Sound
* Salvator-X and Salvator-XS boards with
R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs, and
Draak board with R-Car D3 (r8a77995) SoC
- Consistently name EtherAVB mdio pin group
Geert Uytterhoeven says "When initial support was added for R-Car H3,
the MDIO pin was forgotten, and the MDC pin got its own group named
"mdc". During the addition of support for R-Car M3-W, this mistake was
noticed. But as R-Car H3 and M3-W are pin compatible, and can be
mounted on the same boards, the decision was made to just add the MDIO
pin to the existing "mdc" group. Later this was extended to R-Car H3
ES2.0, and M3-N, because of pin compatibility, and to R-Car D3, in the
name of consistency among R-Car Gen3 SoCs.
However, this decision keeps on being questioned when adding new SoC
support. Hence bite the bullet and admit our mistake, and rename the
pin group from "mdc" to "mdio", like on R-Car Gen2 SoCs."
* Ebisu board with R-Car E3 (r8a77990) SoC
- Initial support: Memory, Main crystal, Serial console
- Enable Ethernet
- Revise PSCI node
Yoshihiro Shimoda says "The basic support patch 2d2dbadba421 ("arm64:
dts: renesas: Add Renesas R8A77990 SoC support") lacks the compatible
"arm,psci-1.0" in the psci node."
- Revise cache controller node
Yoshihiro Shimoda says "The cache controller node should not have
unit-addresses and reg properties."
* V3HSK board with R-Car V3H (r8a77980) SoC
- Initial board device tree
Sergei Shtylov says "Add the initial device tree for the V3H Starter
Kit board. The board has 1 debug serial port (SCIF0); include support
for it, so that the serial console can work."
- Enable PFC support and use for EtherAVB
* V3MSK board with R-Car V3M (r8a77970) SoC
- Add DU/LVDS/HDMI support
Sergei Shtylyov says "Define the V3M Starter Kit board dependent part
of the DU and LVDS device nodes. Also add the device nodes for Thine
THC63LVD1024 LVDS decoder and Analog Devices ADV7511W HDMI
transmitter..."
- Enable PFC for EtherAVB
* Condor board with R-Car V3H (r8a77980) SoC
- Enable eMMC
Sergei Shtylyov says "We're adding the R8A77980 MMC (SDHI)
device nodes and then enable eMMC support on the Condor board."
- Enable PFC support and use for EtherAVB and SCIF0
* Eagle board with R-Car V3M (r8a77970) SoC
- Enable HDMI output
* Eagle board with R-Car V3M (r8a77970) SoC and
Condor board with R-Car V3H (r8a77980) SoC
- Enable CAN-FD
Adds the CAN-FD device nodes so the DT SoC files and enables
single channel CAN-FD support in DT board files.
-----BEGIN PGP SIGNATURE-----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=4IoI
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/late
Renesas ARM64 Based SoC DT Updates for v4.18
* Cleanups:
- Correct whitespace
- sort subnodes of the root and soc nodes
* R-Car M3-N (r8a77965) SoC
- Describe MSIOF SPI, PWM, SDHI and I2C devices in DT
- Add thermal support
* R-Car H3 (r8a7795) and R-Car M3-W (r8a7796) SoCs
- Decrease temperature hysteresis
* R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs
- Add address properties to rcar_sound port nodes
* R-Car H3 (r8a7795), M3-W (r8a7796) V3M (r8a77970) and D3 (r8a77995) SoCs
- Enable IPMMU devices
* R-Car M3-N (r8a77965) and V3H (r8a77980) SoCs
- Use sysc binding macros
- Describe USB2 and USB3 devices in DT
* R-Car V3M (r8a77970) SoC
- Add SMP Support
- Correct IPMMU DS1 bit number
* R-Car V3H (r8a77980) SoC
- Use CPG clock binding macros
* R-Car V3H (r8a77980) and V3M (r8a77970) SoCs
- Disable EtherAVB
* R-Car D3 (r8a77995) SoC
- Describe VIN4 in DT
* Ebisu board with R-Car E3 (r8a77990) SoC
- Initial support
* Salvator-XS boards with R-Car H3 (r8a7795) SoC
- Enable USB2.0 channel 3
* Salvator-X and Salvator-XS boards with M3-N (r8a77965) SoC
- Enable DU
* Salvator-X and Salvator-XS boards with
R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs
- Enable nable VIN, CSI-2 and ADV7482
- Add PMIC DDR Backup Power config
- Add EEPROM
- Enable HDMI Sound
* Salvator-X and Salvator-XS boards with
R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs, and
Draak board with R-Car D3 (r8a77995) SoC
- Consistently name EtherAVB mdio pin group
* Ebisu board with R-Car E3 (r8a77990) SoC
- Initial support: Memory, Main crystal, Serial console
- Enable Ethernet
- Revise PSCI node
- Revise cache controller node
* V3HSK board with R-Car V3H (r8a77980) SoC
- Initial board device tree
- Enable PFC support and use for EtherAVB
* V3MSK board with R-Car V3M (r8a77970) SoC
- Add DU/LVDS/HDMI support
- Enable PFC for EtherAVB
* Condor board with R-Car V3H (r8a77980) SoC
- Enable eMMC
- Enable PFC support and use for EtherAVB and SCIF0
* Eagle board with R-Car V3M (r8a77970) SoC
- Enable HDMI output
* Eagle board with R-Car V3M (r8a77970) SoC and
Condor board with R-Car V3H (r8a77980) SoC
- Enable CAN-FD
* tag 'renesas-arm64-dt-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (102 commits)
arm64: dts: renesas: salvator-common: Add ADV7482 support
arm64: dts: renesas: salvator-common: enable VIN
arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7795-es1: add CSI-2 node
arm64: dts: renesas: r8a7795: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a77965: add I2C support
arm64: dts: renesas: r8a77990: ebisu: Enable EthernetAVB
arm64: dts: renesas: r8a77990: Add EthernetAVB device nodes
arm64: dts: renesas: r8a77990: Add GPIO device nodes
arm64: dts: renesas: r8a77990: Add PFC device node
arm64: dts: renesas: initial V3HSK board device tree
arm64: dts: renesas: r8a77980: disable EtherAVB
arm64: dts: renesas: r8a77970: disable EtherAVB
arm64: dts: renesas: r8a77995: Add VIN4
arm64: dts: renesas: r8a77980: add resets property to CAN-FD node
arm64: dts: renesas: r8a77970: Add Cortex-A53 PMU node
arm64: dts: renesas: r8a77970: Add secondary CA53 CPU core
arm64: dts: renesas: r8a77965: Add SDHI device nodes
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- change to phase out at24 eeprom platform data
- add a missing wakeup pin on pxa320 SoCs
-----BEGIN PGP SIGNATURE-----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=/4US
-----END PGP SIGNATURE-----
Merge tag 'pxa-for-4.18' of https://github.com/rjarzmik/linux into next/soc
This is is the pxa changes for v4.18 cycle :
- change to phase out at24 eeprom platform data
- add a missing wakeup pin on pxa320 SoCs
* tag 'pxa-for-4.18' of https://github.com/rjarzmik/linux:
ARM: pxa3xx: enable external wakeup pins
ARM: pxa: stargate2: use device properties for at24 eeprom
Signed-off-by: Olof Johansson <olof@lixom.net>
The register address should be the full address of the rng, not the
offset from the start of the SCU.
Fixes: 5daa8212c0 ("ARM: dts: aspeed: Describe random number device")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
According to the Intel Software Developers' Manual, Vol. 4, Order No.
335592, these macros have been reversed since they were added in the
initial turbostat commit. The reversed definitions were presumably
copied from turbostat.c to this file.
Fixes: 9c63a650bb ("tools/power/x86/turbostat: share kernel MSR #defines")
Signed-off-by: Matt Turner <mattst88@gmail.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Len Brown <len.brown@intel.com>
ENET "ipg" clock should be IMX7D_ENETx_IPG_ROOT_CLK
rather than IMX7D_ENET_AXI_ROOT_CLK which is for ENET bus
clock.
Based on Andy Duan's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
This cleans up the error handling a lot, as this code will never get
hit.
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim KrÄmář" <rkrcmar@redhat.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Eric Auger <eric.auger@redhat.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: kvm-ppc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: kvmarm@lists.cs.columbia.edu
Cc: kvm@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The kvm struct has been bloating. For example, it's tens of kilo-bytes
for x86, which turns out to be a large amount of memory to allocate
contiguously via kzalloc. Thus, this patch does the following:
1. Uses architecture-specific routines to allocate the kvm struct via
vzalloc for x86.
2. Switches arm to __KVM_HAVE_ARCH_VM_ALLOC so that it can use vzalloc
when has_vhe() is true.
Other architectures continue to default to kalloc, as they have a
dependency on kalloc or have a small-enough struct kvm.
Signed-off-by: Marc Orr <marcorr@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use new return type vm_fault_t for fault handler. For
now, this is just documenting that the function returns
a VM_FAULT value rather than an errno. Once all instances
are converted, vm_fault_t will become a distinct type.
commit 1c8f422059 ("mm: change return type to vm_fault_t")
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Lazy context-switching of FPSIMD registers on arm64
- Allow virtual redistributors to be part of two or more MMIO ranges
-----BEGIN PGP SIGNATURE-----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=DUmC
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM updates for 4.18
- Lazy context-switching of FPSIMD registers on arm64
- Allow virtual redistributors to be part of two or more MMIO ranges
Fix the below crash on Book3E 64. pgtable_page_dtor expects struct
page *arg.
Also call the destructor on non book3s platforms correctly. This frees
up the split PTL locks correctly if we had allocated them before.
Call Trace:
.kmem_cache_free+0x9c/0x44c (unreliable)
.ptlock_free+0x1c/0x30
.tlb_remove_table+0xdc/0x224
.free_pgd_range+0x298/0x500
.shift_arg_pages+0x10c/0x1e0
.setup_arg_pages+0x200/0x25c
.load_elf_binary+0x450/0x16c8
.search_binary_handler.part.11+0x9c/0x248
.do_execveat_common.isra.13+0x868/0xc18
.run_init_process+0x34/0x4c
.try_to_run_init_process+0x1c/0x68
.kernel_init+0xdc/0x130
.ret_from_kernel_thread+0x58/0x7c
Fixes: 702346768 ("powerpc/mm/nohash: Remove pte fragment dependency from nohash")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In commit eae5f709a4 ("powerpc: Add __printf verification to
prom_printf") __printf attribute was added to prom_printf(), which
means GCC started warning about type/format mismatches. As part of
that commit we changed some "%lx" formats to "%llx" where the type is
actually unsigned long long.
Unfortunately prom_printf() doesn't know how to print "%llx", it just
prints a literal "lx", eg:
reserved memory map:
lx - lx
lx - lx
prom_printf() also doesn't know how to print "%u" (only "%lu"), it
just prints a literal "u", eg:
Max number of cores passed to firmware: u (NR_CPUS = 2048)
Instead of:
Max number of cores passed to firmware: 2048 (NR_CPUS = 2048)
This commit adds support for the missing formatters.
Fixes: eae5f709a4 ("powerpc: Add __printf verification to prom_printf")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Stateful CPU architecture extensions may require the signal frame
to grow to a size that exceeds the arch's MINSIGSTKSZ #define.
However, changing this #define is an ABI break.
To allow userspace the option of determining the signal frame size
in a more forwards-compatible way, this patch adds a new auxv entry
tagged with AT_MINSIGSTKSZ, which provides the maximum signal frame
size that the process can observe during its lifetime.
If AT_MINSIGSTKSZ is absent from the aux vector, the caller can
assume that the MINSIGSTKSZ #define is sufficient. This allows for
a consistent interface with older kernels that do not provide
AT_MINSIGSTKSZ.
The idea is that libc could expose this via sysconf() or some
similar mechanism.
There is deliberately no AT_SIGSTKSZ. The kernel knows nothing
about userspace's own stack overheads and should not pretend to
know.
For arm64:
The primary motivation for this interface is the Scalable Vector
Extension, which can require at least 4KB or so of extra space
in the signal frame for the largest hardware implementations.
To determine the correct value, a "Christmas tree" mode (via the
add_all argument) is added to setup_sigframe_layout(), to simulate
addition of all possible records to the signal frame at maximum
possible size.
If this procedure goes wrong somehow, resulting in a stupidly large
frame layout and hence failure of sigframe_alloc() to allocate a
record to the frame, then this is indicative of a kernel bug. In
this case, we WARN() and no attempt is made to populate
AT_MINSIGSTKSZ for userspace.
For arm64 SVE:
The SVE context block in the signal frame needs to be considered
too when computing the maximum possible signal frame size.
Because the size of this block depends on the vector length, this
patch computes the size based not on the thread's current vector
length but instead on the maximum possible vector length: this
determines the maximum size of SVE context block that can be
observed in any signal frame for the lifetime of the process.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Now that the kernel SVE support is reasonably mature, it is
excessive to default sve_max_vl to the invalid value -1 and then
sprinkle WARN_ON()s around the place to make sure it has been
initialised before use. The cpufeatures code already runs pretty
early, and will ensure sve_max_vl gets initialised.
This patch initialises sve_max_vl to something sane that will be
supported by every SVE implementation, and removes most of the
sanity checks.
The checks in find_supported_vector_length() are retained for now.
If anything goes horribly wrong, we are likely to trip a check here
sooner or later.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The powerpc toolchain can compile combinations of 32/64 bit and
big/little endian, so it's convenient to consider, e.g.,
`CC -m64 -mbig-endian`
To be the C compiler for the purpose of invoking it to build target
artifacts. So overriding the CC variable to include these flags works
for this purpose.
Unfortunately that is not compatible with the way the proposed new
Kconfig macro language will work.
After previous patches in this series, these flags can be carefully
passed in using flags instead.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Switch VDSO32 build over to use CROSS32_COMPILE directly, and have
it pass in -m32 after the standard c_flags. This allows endianness
overrides to be removed and the endian and bitness flags moved into
standard flags variables.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some 64-bit toolchains uses the wrong ISA variant for compiling 32-bit
kernels, even with -m32. Debian's powerpc64le is one such case, and
that is because it is built with --with-cpu=power8.
So when cross compiling a 32-bit kernel with a 64-bit toolchain, set
-mcpu=powerpc initially, which is the generic 32-bit powerpc machine
type and scheduling model. CPU and platform code can override this
with subsequent -mcpu flags if necessary.
This is not done for 32-bit toolchains otherwise it would override
their defaults, which are presumably set appropriately for the
environment (moreso than a 64-bit cross compiler).
This fixes a lot of build failures due to incompatible assembly when
compiling 32-bit kernel with the Debian powerpc64le 64-bit toolchain.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
By default, sparse assumes a 64bit machine when compiled on x86-64
and 32bit when compiled on anything else.
This can of course create all sort of problems for the other archs, like
issuing false warnings ('shift too big (32) for type unsigned long'), or
worse, failing to emit legitimate warnings.
Fix this by adding the -m32/-m64 flag, depending on CONFIG_64BIT,
to CHECKFLAGS in the main Makefile (and so for all archs).
Also, remove the now unneeded -m32/-m64 in arch specific Makefiles.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We need to migrate PR KVM during transaction and userspace will use
kvmppc_get_one_reg_pr()/kvmppc_set_one_reg_pr() APIs to get/set
transaction checkpoint state. This patch adds support for that.
So far, QEMU on PR KVM doesn't fully function for migration but the
savevm/loadvm can be done against a RHEL72 guest. During savevm/
loadvm procedure, the kvm ioctls will be invoked as well.
Test has been performed to savevm/loadvm for a guest running
a HTM test program:
https://github.com/justdoitqd/publicFiles/blob/master/test-tm-mig.c
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
In both HV and PR KVM, the KVM_SET_REGS/KVM_GET_REGS ioctl should
be able to perform without the vcpu loaded.
Since the vcpu mutex locking/unlock has been moved out of vcpu_load()
/vcpu_put(), KVM_SET_REGS/KVM_GET_REGS don't need to do ioctl with
the vcpu loaded anymore. This patch removes vcpu_load()/vcpu_put()
from KVM_SET_REGS/KVM_GET_REGS ioctl.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Since the vcpu mutex locking/unlock has been moved out of vcpu_load()
/vcpu_put(), KVM_GET_ONE_REG and KVM_SET_ONE_REG doesn't need to do
ioctl with loading vcpu anymore. This patch removes vcpu_load()/vcpu_put()
from KVM_GET_ONE_REG and KVM_SET_ONE_REG ioctl.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Although we already have kvm_arch_vcpu_async_ioctl() which doesn't require
ioctl to load vcpu, the sync ioctl code need to be cleaned up when
CONFIG_HAVE_KVM_VCPU_ASYNC_IOCTL is not configured.
This patch moves vcpu_load/vcpu_put down to each ioctl switch case so that
each ioctl can decide to do vcpu_load/vcpu_put or not independently.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently guest kernel doesn't handle TAR facility unavailable and it
always runs with TAR bit on. PR KVM will lazily enable TAR. TAR is not
a frequent-use register and it is not included in SVCPU struct.
Due to the above, the checkpointed TAR val might be a bogus TAR val.
To solve this issue, we will make vcpu->arch.fscr tar bit consistent
with shadow_fscr when TM is enabled.
At the end of emulating treclaim., the correct TAR val need to be loaded
into the register if FSCR_TAR bit is on.
At the beginning of emulating trechkpt., TAR needs to be flushed so that
the right tar val can be copied into tar_tm.
Tested with:
tools/testing/selftests/powerpc/tm/tm-tar
tools/testing/selftests/powerpc/ptrace/ptrace-tm-tar (remove DSCR/PPR
related testing).
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently PR KVM doesn't support transaction memory in guest privileged
state.
This patch adds a check at setting guest msr, so that we can never return
to guest with PR=0 and TS=0b10. A tabort will be emulated to indicate
this and fail transaction immediately.
[paulus@ozlabs.org - don't change the TM_CAUSE_MISC definition, instead
use TM_CAUSE_KVM_FAC_UNAV.]
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently privileged-state guest will be run with TM disabled.
Although the privileged-state guest cannot initiate a new transaction,
it can use tabort to terminate its problem state's transaction.
So it is still necessary to emulate tabort. for privileged-state guest.
Tested with:
https://github.com/justdoitqd/publicFiles/blob/master/test_tabort.c
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch adds host emulation when guest PR KVM executes "trechkpt.",
which is a privileged instruction and will trap into host.
We firstly copy vcpu ongoing content into vcpu tm checkpoint
content, then perform kvmppc_restore_tm_pr() to do trechkpt.
with updated vcpu tm checkpoint values.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch adds support for "treclaim." emulation when PR KVM guest
executes treclaim. and traps to host.
We will firstly do treclaim. and save TM checkpoint. Then it is
necessary to update vcpu current reg content with checkpointed vals.
When rfid into guest again, those vcpu current reg content (now the
checkpoint vals) will be loaded into regs.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently kvmppc_handle_fac() will not update NV GPRs and thus it can
return with GUEST_RESUME.
However PR KVM guest always disables MSR_TM bit in privileged state.
If PR privileged-state guest is trying to read TM SPRs, it will
trigger TM facility unavailable exception and fall into
kvmppc_handle_fac(). Then the emulation will be done by
kvmppc_core_emulate_mfspr_pr(). The mfspr instruction can include a
RT with NV reg. So it is necessary to restore NV GPRs at this case, to
reflect the update to NV RT.
This patch make kvmppc_handle_fac() return GUEST_RESUME_NV for TM
facility unavailable exceptions in guest privileged state.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently the kernel doesn't use transaction memory.
And there is an issue for privileged state in the guest that:
tbegin/tsuspend/tresume/tabort TM instructions can impact MSR TM bits
without trapping into the PR host. So following code will lead to a
false mfmsr result:
tbegin <- MSR bits update to Transaction active.
beq <- failover handler branch
mfmsr <- still read MSR bits from magic page with
transaction inactive.
It is not an issue for non-privileged guest state since its mfmsr is
not patched with magic page and will always trap into the PR host.
This patch will always fail tbegin attempt for privileged state in the
guest, so that the above issue is prevented. It is benign since
currently (guest) kernel doesn't initiate a transaction.
Test case:
https://github.com/justdoitqd/publicFiles/blob/master/test_tbegin_pr.c
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The mfspr/mtspr on TM SPRs(TEXASR/TFIAR/TFHAR) are non-privileged
instructions and can be executed by PR KVM guest in problem state
without trapping into the host. We only emulate mtspr/mfspr
texasr/tfiar/tfhar in guest PR=0 state.
When we are emulating mtspr tm sprs in guest PR=0 state, the emulation
result needs to be visible to guest PR=1 state. That is, the actual TM
SPR val should be loaded into actual registers.
We already flush TM SPRs into vcpu when switching out of CPU, and load
TM SPRs when switching back.
This patch corrects mfspr()/mtspr() emulation for TM SPRs to make the
actual source/dest be the actual TM SPRs.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The math registers will be saved into vcpu->arch.fp/vr and corresponding
vcpu->arch.fp_tm/vr_tm area.
We flush or giveup the math regs into vcpu->arch.fp/vr before saving
transaction. After transaction is restored, the math regs will be loaded
back into regs.
If there is a FP/VEC/VSX unavailable exception during transaction active
state, the math checkpoint content might be incorrect and we need to do
treclaim./load the correct checkpoint val/trechkpt. sequence to retry the
transaction. That will make our solution complicated. To solve this issue,
we always make the hardware guest MSR math bits (shadow_msr) consistent
with the MSR val which guest sees (kvmppc_get_msr()) when guest msr is
with tm enabled. Then all FP/VEC/VSX unavailable exception can be delivered
to guest and guest handles the exception by itself.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The transaction memory checkpoint area save/restore behavior is
triggered when VCPU qemu process is switching out/into CPU, i.e.
at kvmppc_core_vcpu_put_pr() and kvmppc_core_vcpu_load_pr().
MSR TM active state is determined by TS bits:
active: 10(transactional) or 01 (suspended)
inactive: 00 (non-transactional)
We don't "fake" TM functionality for guest. We "sync" guest virtual
MSR TM active state(10 or 01) with shadow MSR. That is to say,
we don't emulate a transactional guest with a TM inactive MSR.
TM SPR support(TFIAR/TFAR/TEXASR) has already been supported by
commit 9916d57e64 ("KVM: PPC: Book3S PR: Expose TM registers").
Math register support (FPR/VMX/VSX) will be done at subsequent
patch.
Whether TM context need to be saved/restored can be determined
by kvmppc_get_msr() TM active state:
* TM active - save/restore TM context
* TM inactive - no need to do so and only save/restore
TM SPRs.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Suggested-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch adds 2 new APIs, kvmppc_save_tm_sprs() and
kvmppc_restore_tm_sprs(), for the purpose of TEXASR/TFIAR/TFHAR
save/restore.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch adds 2 new APIs: kvmppc_copyto_vcpu_tm() and
kvmppc_copyfrom_vcpu_tm(). These 2 APIs will be used to copy from/to TM
data between VCPU_TM/VCPU area.
PR KVM will use these APIs for treclaim. or trechkpt. emulation.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
PR KVM host usually runs with TM enabled in its host MSR value, and
with non-transactional TS value.
When a guest with TM active traps into PR KVM host, the rfid at the
tail of kvmppc_interrupt_pr() will try to switch TS bits from
S0 (Suspended & TM disabled) to N1 (Non-transactional & TM enabled).
That will leads to TM Bad Thing interrupt.
This patch manually sets target TS bits unchanged to avoid this
exception.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
According to ISA specification for RFID, in MSR TM disabled and TS
suspended state (S0), if the target MSR is TM disabled and TS state is
inactive (N0), rfid should suppress this update.
This patch makes the RFID emulation of PR KVM consistent with this.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
MSR TS bits can be modified with non-privileged instruction such as
tbegin./tend. That means guest can change MSR value "silently" without
notifying host.
It is necessary to sync the TM bits to host so that host can calculate
shadow msr correctly.
Note, privileged mode in the guest will always fail transactions so we
only take care of problem state mode in the guest.
The logic is put into kvmppc_copy_from_svcpu() so that
kvmppc_handle_exit_pr() can use correct MSR TM bits even when preemption
occurs.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
PowerPC TM functionality needs MSR TM/TS bits support in hardware level.
Guest TM functionality can not be emulated with "fake" MSR (msr in magic
page) TS bits.
This patch syncs TM/TS bits in shadow_msr with the MSR value in magic
page, so that the MSR TS value which guest sees is consistent with actual
MSR bits running in guest.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
This patch simulates interrupt behavior per Power ISA while injecting
interrupt in PR KVM:
- When interrupt happens, transactional state should be suspended.
kvmppc_mmu_book3s_64_reset_msr() will be invoked when injecting an
interrupt. This patch performs this ISA logic in
kvmppc_mmu_book3s_64_reset_msr().
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Currently __kvmppc_save/restore_tm() APIs can only be invoked from
assembly function. This patch adds C function wrappers for them so
that they can be safely called from C function.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
kvmppc_save_tm() invokes store_fp_state/store_vr_state(). So it is
mandatory to turn on FP/VSX/VMX MSR bits for its execution, just
like what kvmppc_restore_tm() did.
Previously HV KVM has turned the bits on outside of function
kvmppc_save_tm(). Now we include this bit change in kvmppc_save_tm()
so that the logic is cleaner. And PR KVM can reuse it later.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
HV KVM and PR KVM need different MSR source to indicate whether
treclaim. or trecheckpoint. is necessary.
This patch add new parameter (guest MSR) for these kvmppc_save_tm/
kvmppc_restore_tm() APIs:
- For HV KVM, it is VCPU_MSR
- For PR KVM, it is current host MSR or VCPU_SHADOW_SRR1
This enhancement enables these 2 APIs to be reused by PR KVM later.
And the patch keeps HV KVM logic unchanged.
This patch also reworks kvmppc_save_tm()/kvmppc_restore_tm() to
have a clean ABI: r3 for vcpu and r4 for guest_msr.
During kvmppc_save_tm/kvmppc_restore_tm(), the R1 need to be saved
or restored. Currently the R1 is saved into HSTATE_HOST_R1. In PR
KVM, we are going to add a C function wrapper for
kvmppc_save_tm/kvmppc_restore_tm() where the R1 will be incremented
with added stackframe and save into HSTATE_HOST_R1. There are several
places in HV KVM to load HSTATE_HOST_R1 as R1, and we don't want to
bring risk or confusion by TM code.
This patch will use HSTATE_SCRATCH2 to save/restore R1 in
kvmppc_save_tm/kvmppc_restore_tm() to avoid future confusion, since
the r1 is actually a temporary/scratch value to be saved/stored.
[paulus@ozlabs.org - rebased on top of 7b0e827c69 ("KVM: PPC: Book3S HV:
Factor fake-suspend handling out of kvmppc_save/restore_tm", 2018-05-30)]
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Prevent speculation at the syscall table decoding by clamping the index
used to zero on invalid system call numbers, and using the csdb
speculative barrier.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Add an implementation of the array_index_mask_nospec() function for
mitigating Spectre variant 1 throughout the kernel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Add assembly and C macros for the new CSDB instruction.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Now that all our infrastructure is in place, let's expose the
availability of ARCH_WORKAROUND_2 to guests. We take this opportunity
to tidy up a couple of SMCCC constants.
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to forward the guest's ARCH_WORKAROUND_2 calls to EL3,
add a small(-ish) sequence to handle it at EL2. Special care must
be taken to track the state of the guest itself by updating the
workaround flags. We also rely on patching to enable calls into
the firmware.
Note that since we need to execute branches, this always executes
after the Spectre-v2 mitigation has been applied.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to offer ARCH_WORKAROUND_2 support to guests, we need
a bit of infrastructure.
Let's add a flag indicating whether or not the guest uses
SSBD mitigation. Depending on the state of this flag, allow
KVM to disable ARCH_WORKAROUND_2 before entering the guest,
and enable it when exiting it.
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
As we're going to require to access per-cpu variables at EL2,
let's craft the minimum set of accessors required to implement
reading a per-cpu variable, relying on tpidr_el2 to contain the
per-cpu offset.
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
If running on a system that performs dynamic SSBD mitigation, allow
userspace to request the mitigation for itself. This is implemented
as a prctl call, allowing the mitigation to be enabled or disabled at
will for this particular thread.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to allow userspace to be mitigated on demand, let's
introduce a new thread flag that prevents the mitigation from
being turned off when exiting to userspace, and doesn't turn
it on on entry into the kernel (with the assumption that the
mitigation is always enabled in the kernel itself).
This will be used by a prctl interface introduced in a later
patch.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On a system where firmware can dynamically change the state of the
mitigation, the CPU will always come up with the mitigation enabled,
including when coming back from suspend.
If the user has requested "no mitigation" via a command line option,
let's enforce it by calling into the firmware again to disable it.
Similarily, for a resume from hibernate, the mitigation could have
been disabled by the boot kernel. Let's ensure that it is set
back on in that case.
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to avoid checking arm64_ssbd_callback_required on each
kernel entry/exit even if no mitigation is required, let's
add yet another alternative that by default jumps over the mitigation,
and that gets nop'ed out if we're doing dynamic mitigation.
Think of it as a poor man's static key...
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We're about to need the mitigation state in various parts of the
kernel in order to do the right thing for userspace and guests.
Let's expose an accessor that will let other subsystems know
about the state.
Reviewed-by: Julien Grall <julien.grall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
