Switch to the new coresight bindings for hardware ports
Cc: linux-omap@vger.kernel.org
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses 26MHz oscillator for the twl4030 HFCLK.
This way we will not depend on the bootloader to configure the
CFG_BOOT:HFCLK_FREQ
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in OMAP dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace deprecated "vmmc_aux" with the generic "vqmmc" binding for
MMC IO supply.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Beagleboard-xM has a LAN9514 USB hub and ethernet controller,
connected to port 2 of the OMAP EHCI controller. The board however has
no EEPROM to store the ethernet MAC address, which is programmed by the
boot loader.
To allow Linux to use the same MAC address as the boot loader (or for
that matter any fixed MAC address), we need a node in the device tree
for the ethernet controller that the boot loader can update at runtime
with a local-mac-address property. Add it, along with an alias for the
ethernet controller to let the boot loader locate it easily.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-beagle-xm.dtb:
"encoder@0 has a unit name, but no reg property"
"encoder@0/ports/port@0/endpoint@0 has a unit name, but no reg property"
"encoder@0/ports/port@1/endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" boolean property to enable the wakeup
source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the pinmux IOPAD macros to define the register absolute physical
address instead of the offset from the padconf base address. This
makes the DTS easier to read since matches the addresses listed in
the Technical Reference Manual.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Many OMAP2+ DTS are not using the defined constants to express
the GPIO polarity. Replace these so the DTS are easier to read.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVNzKFAAoJEIwa5zzehBx3JtEP/1g89CW7iZHAUyIiC+jtgqck
ASoplr13DLD0HWjjWITX3zm7J/iY57YjEv14tHH/xmrh5YCCZ+mRLqiD/Plnv0Zv
JdJRRJv/NMnMlu/tA1aBO326JOt2Vw+3YngmYayDpoRzVifx2YTJLbu2difa+6rM
vN6FpOE6U5jkvM16+gqxKxyx0tGIQz9cTn+9q2V1fDS++vZ2VvqfB5pTNul3BKAF
OVCNFJ/EUE9EPMPbmgDjYmNE/POj64kF32n7NBEQz2Z+nwDNxDAecfF356hV7o5g
JsFLNK+4c2QQqBL775xzCf5kK+n/V2cFEpDica+hU70AdWsjdAlUFrbOsWGUJLRi
4Blrv8GRxEKeOCs8AFKYCM+z3zf2ais7JMteD2VW26ywCwpUt+QEZTUVHRHU3NYQ
BMI7uyTGIH2GyLyS+Av3vikza8IbDIwlYuuDpXhCJSXXgKSnbzCrpjkhyGLccBJR
k3qgUwPJVw9hP1qaaNgvb7p9oNhTP2yLl3fQ68WqI7QWIupW0/s12INhzFFgt6zU
Nzcx010ku9yMeMMGtfiNgA3cMln+Ysfs1UIUOMQ36zP1PCtHJkZgwtZzTsBE4A04
KqmiLL/+7qsconEhEanmDzTpeXiNzERnOKSSqVN7Fwp89GEFJLrWpHSXI+8SBTHC
fB54LRTNYdlcoN0QshcT
=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
The coresight-default-sink configuration option has been
removed from the framework. As such remove it from DT and bindings.
Signed-off-by: Kaixu Xia <xiakaixu@huawei.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ti,codec property is not used (parsed) in omap-twl4030 driver. The ti,twl4030-audio
which ti,codec points by phandle is mfd driver and device for ASoC codec is created
w/o DT compatible string. Removing all references in DT files.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently supporting ETM and ETB. Support for TPIU
and SDTI are yet to be added.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is no longer needed as the device specific wake-up event
can now be specified with interrupts-extended property where
the second interrupt is the pinctrl-single register, such as
the UART3 RX pin.
Note that twl4030_omap3.dtsi needs to set WAKEUPENABLE for
off-idle to properly trigger the PMIC scripts. And GPIO pins
still need to set WAKEUPENABLE for wake-up events.
Signed-off-by: Tony Lindgren <tony@atomide.com>
N900 now seems to shut down the external oscillator when hitting
off-idle.
And Beagle XM seems to have OSC_EN pin connected to allow shutting
down the oscillator looking at the schematics. The oscillator
output is cut off in off-idle and you can monitor it from R56 on
the bottom side of the board near the power jack. Note that for
beagle we need to also enable the UART wake-up event, the others
have that enabled in earlier patches.
OMAP37XX EVM (TMDSEVM3730) does not seem to have twl4030 clken
pin connected, so there is no point trying to enable shutting
down of the oscillator on it for the extra latency it adds.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DT data for OMAP3 Beagle-xM board. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
In omap3.dtsi disable all mcbsp nodes and board dts files can explicitly
enable the mcbsp they are using.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap3_pmx_core pinmux device in the device tree handles the system
controller module (SCM) PADCONFS fonction. Its control registers are
split in two distinct areas, with other SCM registers in-between. Those
other registers can't thus be requested by other drivers as the memory
region gets reserved by the pinmux driver.
Split the omap3_pmx_core device tree node in two for the two memory
regions. The second region address and size depends on the SoC model.
The change in omap3.dtsi fixes an "external abort on non-linefetch" when
doing
cat /sys/kernel/debug/pinctrl/.../pins
on a Nokia N900.
Note that the core2 padconf region is different for 3430 vs 3630,
and does not exist on 3517 as noted by Nishanth Menon <nm@ti.com>.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-By: Sebastian Reichel <sre@debian.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated for 3430 vs 3630 core2 based on Nishant's patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beagle (rev. C4) and Beagle-XM (all revs) need VAUX2 1.8V supply
for the USB PHY.
As the generic PHY driver can't handle more than one supply
at the moment, we configure this supply to be always on.
This will cause a very small power impact if the USB host subsystem
is not in use, about 76.86 micro-W + LDO power.
Older Beagle boards (prior to C4) don't have VAUX2 connected anywhere,
so there won't be any functional impact on those boards other than
some additional LDO power consumption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
We need the fixes in v3.12-rc5, dts changes in omap-for-v3.13/dt, and
the platform data quirk changes in omap-for-v3.13/quirk to start
removing omap3 board files without breaking things.
Provide RESET GPIO and Power regulator for the USB PHY,
the USB Host port mode and the PHY device for the controller.
Also provide pin multiplexer information for USB host pins.
We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
SoC family definitions at the moment are reactive to board needs
as a result, beagle-xm would matchup with ti,omap3 which invokes
omap3430_init_early instead of omap3630_init_early. Obviously, this is
the wrong behavior.
With clock node dts conversion, we get the following warnings before
system hangs as a result and 3630 based platforms fails to boot
(uart4 clocks are only present in OMAP3630 and not present in
OMAP3430):
...
omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
omap_hwmod: uart4: cannot _init_clocks
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434
_init+0x6c/0x80()
omap_hwmod: uart4: couldn't init clocks
...
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: timer12: enabled state can only be entered from
initialized, idle, or disabled state
...
WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224
_idle+0xd4/0xf8()
omap_hwmod: timer12: idle state can only be entered from enabled state
WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: uart4: enabled state can only be entered from
initialized, idle, or disabled state
So, add specific compatiblity for 3630 to allow match for Beagle-XM
platform.
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: left out ti,omap343x, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Updated the usb_otg_hs dt data to include the *phy* and *phy-names*
binding in order for the driver to use the new generic PHY framework.
Also updated the Documentation to include the binding information.
The PHY binding information can be found at
Documentation/devicetree/bindings/phy/phy-bindings.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The beagle and beagle-xm entries were inside the same double quote.
Split them to have two distinct entries.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
On most OMAP3 platforms, the twl4030 IRQ line is connected to the
SYS_NIRQ line on OMAP. Add another DTS include file
(twl4030_omap3.dtsi) for boards that hook up the twl4030 this way
to include.
This allows RTC wake from off-mode to work again on OMAP3-based
platforms with twl4030. Tested on 3530/Beagle, 3730/Beagle-xM,
3530/Overo, 3730/Overo-STORM.
Special thanks to Florian Vaussard for suggesting use of preprocessor
feature.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Using the gpio-keys bindings, configure the user button on Beagle
boards. Since the user button is enabled as a wakeup source, also
ensure the GPIO pin is mux'd correctly and has IO ring wakeups enabled,
so it can also wakeup from off mode.
Special thanks to Florian Vaussard for suggesting the preprocessor
feature.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Ensure the console uart (UART3) on these boards is mux'd correctly, and
IO ring wakeup is enabled.
This is needed for serial console wakeups when using DT boot.
Thanks to Florian Vaussard for suggestion to use preprocessor
features.
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
If a board isn't using twl4030, then dtc will complain about the missing
phandle (which is in twl4030.dtsi). Move the phy declaration to the dts
files.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define VDD1 regulator in twl4030 DT and mark it as the supply for the
various OMAP34xx/35xx/36xx/37xx platforms (all use TWL4030 variants with
VDD1 supplying the CPU).
NOTE: This currently will use I2C1 bus communication path to set the
voltage in device tree boot. In the legacy non device tree boot, we
continue to use twl-common.c which bypasses I2C1 bus communication path
and uses I2C4 bus path using OMAP voltage libraries. We should
eventually be able to use I2C4 path once we have voltage regulator for
OMAP which is capable of using the voltage controller/voltage processor
IP blocks.
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add usb otg data node in omap4/omap3 device tree file. Also update
the node with board specific setting in omapx-<board>.dts file.
The dt data specifies among others the interface type (ULPI or UTMI),
mode which is mostly OTG, power that specifies the amount of power
this can supply when in host mode.
The information about usb otg node is available @
Documentation/devicetree/bindings/usb/omap-usb.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
We have proper driver stack to handle the pmu_stat LED which is connected
PWMB of twl4030.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add a minimal dts for original OMAP3430/3530 version of the Beagle board. This
version of the Beagle board has 256MB of DDR and features the same TWL4030
power management IC (PMIC) as the Beagle board XM.
Given that the Beagle and Beagle-XM boards use the same PMIC, move the
definition of the VSIM regulator into the TWL4030.dtsi file so that we do not
need to duplicate in the Beagle board dts file.
This has been boot tested on an OMAP3530 Beagle board and verifing that the
SD/MMC interface is working with a SD card.
V2 changes
- Rebased upon of devel-dt
- Corrected copyright date in omap3-beagle.dts file
- Added LED support after verifing that Beagle and Beagle XM have the same LED
configuration
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
The extra serial port is not available on 34xx. And the current
omap3-beagle.dts file is for omap3-beagle-xm.dts as it lists 512MB
of memory.
Please somebody submit a new omap3-beagle.dts for the original 34xx
BeagleBoard after testing it properly.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
