The platform specific wake-up interrupt is optional. Don't print
an error message in case it is missing, merely inform the user in
this case.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch add qca_set_bdaddr() to set the device
address for latest Qualcomm Bluetooth chipset wcn3990 and above.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom controller on aries S5PV210 boards sends out a couple of
unknown packets after the firmware is loaded. This will cause
logging of errors such as:
Bluetooth: hci0: Frame reassembly failed (-84)
This is probably also the case with other boards, as there are related
Android userspace patches for custom ROMs such as
https://review.lineageos.org/#/c/LineageOS/android_system_bt/+/142721/
Since this appears to be intended behaviour, treated them as diagnostic
packets.
Note that this is another variant of commit 01d5e44ace
("Bluetooth: hci_bcm: Handle empty packet after firmware loading")
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On many devices the RTL8723BS device gets reset during suspend/resume,
causing it to lose its firmware and all state.
Testing has shown it drops back to communicating at 115200 bps and sends
sync-request packages, indicating it has been fully reset.
This commit fixes this by queueing a reprobe on resume.
This mirrors how USB RTL BT devices, which have the same problem, are
handled in the btusb driver, there we set the USB_QUIRK_RESET_RESUME for
all RTL devices, which also causes a reprobe on resume. The only difference
is that here we need to do the reprobe ourselves.
Since we are doing a full reprobe on resume now, we can also turn off the
device on suspend to save power while suspended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for vendor specific suspend / resume callbacks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Trivial fix to clean up an indentation issue, remove spaces
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
HCI_QUIRK_RESET_ON_CLOSE quirk is required for BT v1.0 based devices,
to send a reset command to the chip during hci device close. Serdev
architecture is used for the latest BT chips, which doesn't require to
send the reset command during close. If still chips required reset
command during close, it would be better enabling it in the vendor
probes or in proto setup.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The barriers are redundant because atomic_test_and_clear_bit() already
provides the required full ordering for the cases in question (that is,
when the bit is cleared).
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM43430A0 has the default MAC address 43:43:A0:12:1F:AC if none
is given. This address was found when enabling Bluetooth on a bunch of
boards with the AMPAK AP6210 module, all sharing the same address. It
also contains the sequence 4343A0, which is suspicious as that is also
the name the chip identifies itself as.
Add this to the list of default MAC addresses and leave it to the user
to configure a valid one.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM4330 chip is a 802.11 a/b/g/n + Bluetooth 4.0 + HS controller.
This patch adds a compatible string match to the serdev driver for the
Bluetooth part of the chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM20702A1 chip is a single-chip Bluetooth 4.0 controller and
transceiver. It is found in the AMPAK AP6210 WiFi+BT package.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The datasheets for BCM20702 and BCM43438 both have power up time
sequence graphs, however they are slightly different. Both chips
also have an internal power-on-reset, which holds the chip in reset
for a short time after the regulators are enabled.
For the BCM20702, the time period from when the regulators are enabled,
until the chip settles and comes out of sleep state, is 6564 ~ 8171 us.
For the BCM43438, the graph only shows the time period from when the
regulators are enabled until the chip responds by driving the host's
CTS line low, assuming the host has already driven its RTS line low.
This is shown to be 6.5 sleep cycles, with the sleep clock at 32.768
kHz. This is around 2 ms.
Wait a full 10 ms after the regulators are enabled to account for signal
rising times.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO.
The former provides overall power for the chip, while the latter powers
the I/O pins and buffers.
Model these two as regulator supplies, and let the driver manage them
in the same way as it does the clock supply.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth controllers support a secondary LPO clock at
32.768 kHz. This external clock provides low power timing, and also
a way to detect the frequency of the main reference clock. On many
designs without NVRAM and a non-default reference clock, this must
be used or the controller will not function correctly.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Originally the device tree binding only specified one clock reference,
with the name "extclk". The driver simply retrieves the clock without
bothering to specify a name.
Since we added a second clock to the binding, we need to fetch the
clocks by name now. First we try the new name "txco", then fall back
to the old name "extclk", and finally try retrieving a clock without
using any name, to cover any instances where a bad device tree or
firmware worked by accident.
In the last case, we should take care that we don't get the same
clock twice when we add support for the "lpo" clock.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver currently checks the clk pointer for an error condition, as
returned by clk_get, before every invocation of the clk consumer API.
This is redundant if the goal is simply to ignore the errors, thereby
making the clk optional. The clk consumer API already checks if the
pointer is NULL or not.
Simplify the code a bit by assigning NULL to the clk pointer if the
error condition is one we want to ignore, which is every error except
deferred probing.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On some systems that actually have the bluetooth controller wired up
with an extra clock signal, it's possible the bluetooth controller
probes before the clock provider. clk_get would return a defer probe
error, which was not handled by this driver.
Handle this properly, so that these systems can work reliably.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull tty ioctl updates from Al Viro:
"This is the compat_ioctl work related to tty ioctls.
Quite a bit of dead code taken out, all tty-related stuff gone from
fs/compat_ioctl.c. A bunch of compat bugs fixed - some still remain,
but all more or less generic tty-related ioctls should be covered
(remaining issues are in things like driver-private ioctls in a pcmcia
serial card driver not getting properly handled in 32bit processes on
64bit host, etc)"
* 'work.tty-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (53 commits)
kill TIOCSERGSTRUCT
change semantics of ldisc ->compat_ioctl()
kill TIOCSER[SG]WILD
synclink_gt(): fix compat_ioctl()
pty: fix compat ioctls
compat_ioctl - kill keyboard ioctl handling
gigaset: add ->compat_ioctl()
vt_compat_ioctl(): clean up, use compat_ptr() properly
gigaset: don't try to printk userland buffer contents
dgnc: don't bother with (empty) stub for TCXONC
dgnc: leave TIOC[GS]SOFTCAR to ldisc
remove fallback to drivers for TIOCGICOUNT
dgnc: break-related ioctls won't reach ->ioctl()
kill the rest of tty COMPAT_IOCTL() entries
dgnc: TIOCM... won't reach ->ioctl()
isdn_tty: TCSBRK{,P} won't reach ->ioctl()
kill capinc_tty_ioctl()
take compat TIOC[SG]SERIAL treatment into tty_compat_ioctl()
synclink: reduce pointless checks in ->ioctl()
complete ->[sg]et_serial() switchover
...
BCM43430 devices soldered onto the PCB (non-removable)
use an UART connection for bluetooth.
But also advertise btsdio support on their 3th sdio function.
Signed-off-by: Cho, Yu-Chen <acho@suse.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
First of all, make it return int. Returning long when native method
had never allowed that is ridiculous and inconvenient.
More importantly, change the caller; if ldisc ->compat_ioctl() is NULL
or returns -ENOIOCTLCMD, tty_compat_ioctl() will try to feed cmd and
compat_ptr(arg) to ldisc's native ->ioctl().
That simplifies ->compat_ioctl() instances quite a bit - they only
need to deal with ioctls that are neither generic tty ones (those
would get shunted off to tty_ioctl()) nor simple compat pointer ones.
Note that something like TCFLSH won't reach ->compat_ioctl(),
even if ldisc ->ioctl() does handle it - it will be recognized
earlier and passed to tty_ioctl() (and ultimately - ldisc ->ioctl()).
For many ldiscs it means that NULL ->compat_ioctl() does the
right thing. Those where it won't serve (see e.g. n_r3964.c) are
also easily dealt with - we need to handle the numeric-argument
ioctls (calling the native instance) and, if such would exist,
the ioctls that need layout conversion, etc.
All in-tree ldiscs dealt with.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.
Signed-off-by: David S. Miller <davem@davemloft.net>
As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:
kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)
Signed-off-by: Kees Cook <keescook@chromium.org>
When there is an error in either ath3k_load_firmware() or
ath3k_load_fwfile(), the inlined function ath3k_log_failed_loading() is
called receiving the error returned and both the block size requested to
load and the size actually loaded. These values are printed in an error
message using the macro BT_ERR.
This patch changes that function in order to print the variable "count"
as well, to show more information when a failing firmware loading
operation happens. The calls to the older function were changed to the
new one.
This event is being monitored in a laptop with an adapter which
identifies itself as 0cf3:0036, where sometimes there are errors in the
firmware loading process.
Signed-off-by: Luiz Carlos Ramos <lramos.prof@yahoo.com.br>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
observed sometimes data is coming with unaligned address from kernel
BT stack. If unaligned address is passed, some data in payload is
stripped when packet is loading to firmware and this results, BT
connection timeout is happening.
sh# hciconfig hci0 up
Can't init device hci0: hci0 command 0x0c03 tx timeout
Fixed this by moving the data to aligned address.
Signed-off-by: Sanjay Kumar Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This device is included in the RTL8822CU combination wifi and BT part,
as well as the BT part of the RTL8822CE.
The necessary firmware has been submitted to the linux-firmware
project.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fixed error in space required before paranthesis
in drivers/bluetooth/hci_serdev.c
Signed-off-by: Jagdish Tirumala <t.jag587@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch enables power off support for hci down and power on support
for hci up. As wcn3990 power sources are ignited by regulators, we will
turn off them during hci down, i.e. an complete power off of wcn3990.
So while hci up, will call vendor setup which will turn on the regulators,
requests BT chip version and download the firmware.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Intel "new" controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Don't populate the array extension_sig on the stack but instead make it
static. Makes the object code smaller by 75 bytes:
Before:
text data bss dec hex filename
14325 4920 0 19245 4b2d drivers/bluetooth/btrtl.o
After:
text data bss dec hex filename
14186 4984 0 19170 4ae2 drivers/bluetooth/btrtl.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This will help to check the status of protocol while dequeuing an
skb packet. In some instaces we will end up kernel crash,
where proto close is called and we trying to dequeue an packet.
[ 500.142902] [<ffffff80080f9ce4>] do_raw_spin_lock+0x1c/0xe0
[ 500.148643] [<ffffff80088f1c7c>] _raw_spin_lock_irqsave+0x38/0x48
[ 500.154917] [<ffffff8008780ce8>] skb_dequeue+0x28/0x84
[ 500.160209] [<ffffff8000ad6f48>] 0xffffff8000ad6f48
[ 500.165230] [<ffffff8000ad6610>] 0xffffff8000ad6610
[ 500.170257] [<ffffff80080c7ce8>] process_one_work+0x238/0x3e4
[ 500.176174] [<ffffff80080c8330>] worker_thread+0x2bc/0x3d4
[ 500.181821] [<ffffff80080cdabc>] kthread+0x138/0x140
[ 500.186945] [<ffffff80080844e0>] ret_from_fork+0x10/0x18
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Clearing HCI_UART_PROTO_READY will avoid usage of proto function pointers
before running the proto close function pointer. There is chance of kernel
crash, due to usage of non proto close function pointers after proto close.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Removed serdev_device_open/close functions from qca_open/close as
they are called in hci_uart_register_device() and
hci_uart_unregister_device() functions.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The percpu_rw_semaphore is not currently freed, and this leads to
a crash when the stale rcu callback is invoked. DEBUG_OBJECTS
detects this.
ODEBUG: free active (active state 1) object type: rcu_head hint: (null)
------------[ cut here ]------------
WARNING: CPU: 1 PID: 2024 at debug_print_object+0xac/0xc8
PC is at debug_print_object+0xac/0xc8
LR is at debug_print_object+0xac/0xc8
Call trace:
[<ffffff80082e2c2c>] debug_print_object+0xac/0xc8
[<ffffff80082e40b0>] debug_check_no_obj_freed+0x1e8/0x228
[<ffffff8008191254>] kfree+0x1cc/0x250
[<ffffff80083cc03c>] hci_uart_tty_close+0x54/0x108
[<ffffff800832e118>] tty_ldisc_close.isra.1+0x40/0x58
[<ffffff800832e14c>] tty_ldisc_kill+0x1c/0x40
[<ffffff800832e3dc>] tty_ldisc_release+0x94/0x170
[<ffffff8008325554>] tty_release_struct+0x1c/0x58
[<ffffff8008326400>] tty_release+0x3b0/0x490
[<ffffff80081a3fe8>] __fput+0x88/0x1d0
[<ffffff80081a418c>] ____fput+0xc/0x18
[<ffffff80080c0624>] task_work_run+0x9c/0xc0
[<ffffff80080a9e24>] do_exit+0x24c/0x8a0
[<ffffff80080aa4e0>] do_group_exit+0x38/0xa0
[<ffffff80080aa558>] __wake_up_parent+0x0/0x28
[<ffffff8008082c00>] el0_svc_naked+0x34/0x38
---[ end trace bfe08cbd89098cdf ]---
Signed-off-by: Hermes Zhang <chenhuiz@axis.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case memory resources for *fw* were allocated, release them before
return.
Addresses-Coverity-ID: 1472611 ("Resource leak")
Fixes: 7237c4c9ec ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
At the moment we only support ACPI enumeration for serial port attached
RTL bluetooth controllers.
This commit adds a dependency on ACPI to the BT_HCIUART_RTL configuration
option, fixing the following warning when ACPI is not enabled:
drivers/bluetooth/hci_h5.c:920:22: warning: 'rtl_vnd' defined but not used
Cc: Arnd Bergmann <arnd@arndb.de>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We're supposed to pass the number of elements in the mtk_recv_pkts, not
the number of bytes.
Fixes: 7237c4c9ec ("Bluetooth: mediatek: Add protocol support for MediaTek serial devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Like all the other UART protocols, introduce a configuration option for
Realtek based serial devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a driver based on serdev driver for the MediaTek serial protocol
based on running H:4, which can enable the built-in Bluetooth device inside
MT7622 SoC.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Using HCI_VENDOR_PKT for vendor specific events does work since it has
also the value 0xff, but it is actually the packet type indicator
constant and not the event constant. So introduce HCI_EV_VENDOR and
use it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This driver was recently updated to use serdev, so add the appropriate
dependency. Without this one can get compiler warnings like this if
CONFIG_SERIAL_DEV_BUS is not enabled:
CC [M] drivers/bluetooth/hci_h5.o
drivers/bluetooth/hci_h5.c:934:36: warning: ‘h5_serdev_driver’ defined but not used [-Wunused-variable]
static struct serdev_device_driver h5_serdev_driver = {
^~~~~~~~~~~~~~~~
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support to set voltage/current of various regulators
to power up/down Bluetooth chip wcn3990.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In function qca_setup, we set initial and operating speeds for Qualcomm
Bluetooth SoC's. This block of code is common across different
Qualcomm Bluetooth SoC's. Instead of duplicating the code, created
a wrapper function to set the speeds. So that future coming SoC's
can use these wrapper functions to set speeds.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Redefinition of qca_uart_setup will help future Qualcomm Bluetooth
SoC, to use the same function instead of duplicating the function.
Added new arguments soc_type and soc_ver to the functions.
These arguments will help to decide type of firmware files
to be loaded into Bluetooth chip.
soc_type holds the Bluetooth chip connected to APPS processor.
soc_ver holds the Bluetooth chip version.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some of the QCA BTSoC ROME functions, are used for different versions
or different make of BTSoC's. Instead of duplicating the same functions
for new chip, update names of the functions that are used for both
chips to keep this generic and would help in future when we would have
new BT SoC. To have generic text in logs updated from ROME to QCA where
ever possible. This avoids confusion to user, when using the future
Qualcomm Bluetooth SoC's. Updated BT_DBG, BT_ERR and BT_INFO with
bt_dev_dbg, bt_dev_err and bt_dev_info where ever applicable.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for the enable and device-wake GPIOs used on ACPI enumerated
RTL8723BS devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement support for the RTL8723BS chip.
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
[hdegoede@redhat.com: Port from bt3wire.c to hci_h5.c, drop broken GPIO code]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Allow vendor-specific setup, open, and close functions to be defined.
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
[hdegoede@redhat.com: Port from bt3wire.c to hci_h5.c, drop dt support]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add basic support for serdev enumerated devices, note sine this does
not (yet) declare any of / ACPI ids to bind to atm this is a nop.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The contents of the rtl_bt/rtlXXXX_config.bin file may be board specific
allow the caller of btrtl_initialize to specify a postfix identifying
the board, which if specified will make btrtl_initialize look for
rtl_bt/rtlXXXX_config-<postfix>.bin instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Realtek RTL8723BS and RTL8723DS chipsets are SDIO wifi chips. They
also contain a Bluetooth module which is connected via UART to the host.
Realtek's userspace initialization tool (rtk_hciattach) differentiates
these two via the HCI version and revision returned by the
HCI_OP_READ_LOCAL_VERSION command.
Additionally we apply these checks only the for UART devices. Everything
else is assumed to be a "RTL8723B" which was originally supported by the
driver (communicating via USB).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The UART settings are embedded in the config blob. This has to be parsed
to successfully initialize the Bluetooth part of the RTL8723BS (which is
an SDIO chip, but the Bluetooth part is connected via UART).
The Realtek "rtl8723bs_bt" and "rtl8723ds_bt" userspace Bluetooth UART
initialization tools (rtk_hciattach) use the following sequence:
- send H5 sync pattern (already supported by hci_h5)
- get LMP version (already supported by btrtl)
- get ROM version (already supported by btrtl)
- load the firmware and config for the current chipset (already
supported by btrtl)
- read UART settings from the config blob (part of this patch)
- send UART settings via a vendor command to the device (which changes
the baudrate of the device and enables or disables flow control
depending on the config)
- change the baudrate and flow control settings on the host
- send the firmware and config blob to the device (already supported by
btrtl)
Sending the last firmware and config blob download command
(rtl_download_cmd) fails if the UART settings are not updated
beforehand. This is presumably because the device applies the config
right after the firmware and config blob download - which means that at
this point the host is using different UART settings than the device
(which will obviously result in non-working communication).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Consistently use rtl_dev_err and rtl_dev_info everywhere for messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This prepares the btrtl code so it can be used to initialize Bluetooth
modules connected via UART (these are found for example on the RTL8723BS
and RTL8723DS SDIO chips, which come with an embedded UART Bluetooth
module).
The Realtek "rtl8723bs_bt" and "rtl8723ds_bt" userspace Bluetooth UART
initialization tools (rtk_hciattach) use the following sequence:
1) send H5 sync pattern (already supported by hci_h5)
2) get LMP version (already supported by btrtl)
3) get ROM version (already supported by btrtl)
4) load the firmware and config for the current chipset (already
supported by btrtl)
5) read UART settings from the config blob (currently not supported)
6) send UART settings via a vendor command to the device (which changes
the baudrate of the device and enables or disables flow control
depending on the config)
7) change the baudrate and flow control settings on the host
8) send the firmware and config blob to the device (already supported by
btrtl)
The main reason why the initialization has to be split is step #7. This
requires changes to the underlying "bus", which should be kept outside
of the "generic" btrtl driver.
The idea for this split is borrowed from the btbcm driver but adjusted
where needed (the btrtl driver for example needs two blobs: firmware and
config, while the btbcm only needs one).
This also prepares the code for step #5 (parsing the config blob) by
centralizing the code which loads the firmware and config blobs and
storing the result in the new struct btrtl_device_info.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes the firmware names show up in modinfo.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace the BT_ERR functions with bt_dev_err to get a consistent error
printout that always prefixes the HCI device identifier.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Issue description: Intel 7265 shares the same RF with Wifi and BT.
In the shutdown scenario turn off BT, followed by turn WiFi off
and on causing error in RF calibration in WiFi Module
Solution: before shutdown BT ensure any RF activity to clear by
HCI reset command.
Reference Logs:
ERR kernel: [ 386.193284] iwlwifi 0000:01:00.0: Failed to run INIT calibrations: -5
ERR kernel: [ 386.193298] iwlwifi 0000:01:00.0: Failed to run INIT ucode: -5
ERR kernel: [ 386.193309] iwlwifi 0000:01:00.0: Failed to start RT ucode: -5
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Singed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
qca_open() and qca_set_baudrate() are never called in atomic context.
They call kzalloc() and bt_skb_alloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
inject_cmd_complete() is only called by intel_dequeue(),
which is never called in atomic context.
inject_cmd_complete() calls bt_skb_alloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
inject_cmd_complete() is only called by btusb_send_frame_intel(),
which is set to hdev->send, and hdev->send() is never
called in atomic context.
inject_cmd_complete() calls bt_skb_alloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btmrvl_sdio_card_to_host() is never called in atomic context.
It calls bt_skb_alloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bpa10x_send_frame() is only set to hdev->send, and hdev->send() is never
called in atomic context.
bpa10x_send_frame() calls usb_alloc_urb(), kmalloc() and usb_submit_urb()
with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bluecard_hci_set_baud_rate() is never called in atomic context.
bluecard_hci_set_baud_rate() is only by bluecard_hci_open(), which is
set to hdev->open, and hdev->open() is never called in atomic context.
bluecard_hci_set_baud_rate() calls bt_skb_alloc() with GFP_ATOMIC,
which is not necessary. GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
bfusb_send_frame() is only set to hdev->send, and hdev->send() is never
called in atomic context.
bfusb_send_frame() calls bt_skb_alloc() with GFP_ATOMIC, which is not
necessary. GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The USB completion callback does not disable interrupts while acquiring
the ->lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave variant of the locking primitives.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This breaks the build as this header is not meant to be used in this
way.
./include/linux/unaligned/access_ok.h:8:28: error: redefinition of ‘get_unaligned_le16’
static __always_inline u16 get_unaligned_le16(const void *p)
^~~~~~~~~~~~~~~~~~
In file included from drivers/bluetooth/hci_nokia.c:32:
./include/linux/unaligned/le_struct.h:7:19: note: previous definition of ‘get_unaligned_le16’ was here
static inline u16 get_unaligned_le16(const void *p)
Use asm/unaligned.h instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
Init hci_uart->init_ready so that hci_uart_init_ready() works properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make hci_uart_register_device() and hci_uart_unregister_device() call
serdev_device_close()/open() themselves instead of relying on the various
hci_uart drivers to do this for them.
Besides reducing code complexity, this also ensures correct error checking
of serdev_device_open(), which was missing in a few drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For reasons explained in detail in commit 3611f4d2a5 ("hci_ldisc:
fix null pointer deref") the hci_uart_close() functions sets
hci_dev->flush to NULL.
But the device may be re-opened after a close, this commit restores the
hci_dev->flush callback on open().
Note this commit also moves the nearly empty defition of hci_uart_open()
a bit down in the file to avoid the need for forward declaring
hci_uart_flush().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Re-use kstrtol_from_user() instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixes the following warning during boot:
do not call blocking ops when !TASK_RUNNING; state=1 set at
[<(ptrval)>] qca_setup+0x194/0x750 [hci_uart]
WARNING: CPU: 2 PID: 1878 at kernel/sched/core.c:6135
__might_sleep+0x7c/0x88
In qca_set_baudrate(), the current task state is set to
TASK_UNINTERRUPTIBLE before going to sleep for 300ms. It was then
restored to TASK_INTERRUPTIBLE. This patch sets the current task state
back to TASK_RUNNING instead.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Dell Inspiron 5565 uses a QCA Rome chip which needs to be reset
(and have its firmware reloaded) for bluetooth to work after
suspend/resume.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=15750392
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
checkpatch.pl shows a warning for these unnecessary curly braces.
so just removed those curly braces.
Signed-off-by: Vaibhav Murkute <vaibhavmurkute88@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since commit 3c47d19ff4 ("drivers: base: add coredump driver ops")
it is possible to initiate a device coredump from user-space. This
patch adds support for it in btmrvl_sdio adding the .coredump()
driver callback. This makes dump through debugfs obsolete so removing
it.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In commit f44cb4b19e ("Bluetooth: btusb: Fix quirk for Atheros
1525/QCA6174") we tried to address the non-working Atheros BT devices
by changing the quirk from BTUSB_ATH3012 to BTUSB_QCA_ROME. This made
such devices working while it turned out to break other existing chips
with the very same USB ID, hence it was reverted afterwards.
This is another attempt to tackle the issue. The essential point to
use BTUSB_QCA_ROME is to apply the btusb_setup_qca() and do RAM-
patching. And the previous attempt failed because btusb_setup_qca()
returns -ENODEV if the ROM version doesn't match with the expected
ones. For some devices that have already the "correct" ROM versions,
we may just skip the setup procedure and continue the rest.
So, the first fix we'll need is to add a check of the ROM version in
the function to skip the setup if the ROM version looks already sane,
so that it can be applied for all ath devices.
However, the world is a bit more complex than that simple solution.
Since BTUSB_ATH3012 quirk checks the bcdDevice and bails out when it's
0x0001 at the beginning of probing, so the device probe always aborts
here.
In this patch, we add another check of ROM version again, and if the
device needs patching, the probe continues. For that, a slight
refactoring of btusb_qca_send_vendor_req() was required so that the
probe function can pass usb_device pointer directly before allocating
hci_dev stuff.
Fixes: commit f44cb4b19e ("Bluetooth: btusb: Fix quirk for Atheros 1525/QCA6174")
Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1082504
Tested-by: Ivan Levshin <ivan.levshin@microfocus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds rampatch download compatibility for ROME >= 3.2.
Starting with ROME 3.2, the 'download mode' field of the rampatch
header indicates if the controller acknowledges (or not) the received
rampatch segments. If not, we need to send all the segments without
expecting any event from the controller (except for the last segment).
Goal is (I assume) to speed-up rampatch download.
This fixes BT on Dragonboard-600c P2 which includes the following BT
controller:
hci0: ROME Patch Version Request
hci0: Product:0x00000008
hci0: Patch :0x00000111
hci0: ROM :0x00000302
hci0: SOC :0x00000023
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When both CONFIG_BT_HCIUART_INTEL and CONFIG_BT_HCIUART_BCM are not
selected, sparse complains like this:
drivers/bluetooth/hci_ldisc.c:437:9: warning: switch with no cases
Fix the sparse warning by proving a default switch case.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initialize hw_name to "BCM", this avoids the need for a number of NULL
checks on hw_name later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_setup_patchram() starts with initializing the controller (and
getting the firmware filename) and then after loading the firmware,
does a re-init. This almost entirely duplicates the code in
btbcm_initialize(), use that function instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_finalize() does a re-init of the controller, which is almost the
same as the initial init. Modify btbcm_initialize() so that it can be
used for this re-init and modify btbcm_finalize() to use it.
As an added bonus this also makes the dev_info from btbcm_finalize()
use the proper hw_name instead of always printing "BCM".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Make btbcm_initialize() also work for USB connected device,
btbcm_initialize() and btbcm_setup_patchram() are quite similar,
this is a preparation patch for making btbcm_setup_patchram() use
btbcm_initialize() to remove the code duplication.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We are using the same loop in both the UART and USB bus cases, refactor
things a bit to share the loop.
This is mostly meant to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btbcm_setup_patchram() was using the upper nibble of the revision code to
determine if we are dealing with an uart or USB connected bcm-bt device,
but just as btbcm_initialize() has started accepting 1 and 2 as uart
connected devices, I've now encountered an USB connected device (0a5c:216c)
which has 0 in the upper nibble. So it seems that the upper nibble is not
really a reliable indicator of the bus type.
Instead check hdev->bus which does give us a reliable indication. This
fixes the patchram code trying to load the patchram by the fallback BCM.hcd
filename, now it correctly requests BCM43142A0-0a5c-216c.hcd.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for Qualcomm serial slave devices. Probe the serial device,
retrieve its maximum speed and register a new hci uart device.
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
AOSP use userspace firmware loader to load firmwares, which will
return -EAGAIN in case qca/rampatch_00440302.bin is not found.
Since there is no rampatch for dragonboard820c QCA controller
revision, just make it work as is.
CC: Loic Poulain <loic.poulain@linaro.org>
CC: Nicolas Dechesne <nicolas.dechesne@linaro.org>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johan Hedberg <johan.hedberg@gmail.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
HCI RX/TX byte counters were only incremented when sending ACL packets.
To reflect the real HCI traffic, we need to increment these counters on
HCI events and HCI commands as well.
Increment error counter on rpmsg errors.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Interrupts specified through an "Interrupt" ACPI resource (versus through
a "GpioInt" resource) are now always assumed to be active low.
When this change was originally made the Thinkpad 8 quirk was kept around
because it was uncertain if the Thinkpad 8 uses an "Interrupt" or a
"GpioInt" resource.
Bug https://bugzilla.kernel.org/show_bug.cgi?id=196701 has a DSDT for the
Thinkpad 8 attached and it uses an "Interrupt" resource, so the quirk is
not necessary and the quirk, as well as the irq-active-low quirk handling
code can be removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Meegopad T08 hdmi-stick (think Intel computestick) has a brcm43430
wifi/bt combo chip. The BCM2E90 ACPI device describing the BT part does
contain a valid ActiveLow GpioInt entry, but the GPIO it points to never
goes low, so either the IRQ pin is not connected, or the ACPI resource-
table points to the wrong GPIO.
Eitherway things will not work if we try to use the specified IRQ, this
commits adds a DMI based broken-irq blacklist and disables use of the IRQ
and thus also runtime-pm for devices on this list.
This blacklist starts with the the Meegopad T08, fixing bluetooth not
working on this hdmi-stick. Since this is not a battery powered device
the loss of runtime-pm is not really an issue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Dell XPS 13 9360 uses a QCA Rome chip which needs to be reset
(and have its firmware reloaded) for bluetooth to work after
suspend/resume.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Cc: stable@vger.kernel.org
Cc: Garrett LeSage <glesage@redhat.com>
Reported-and-tested-by: Garrett LeSage <glesage@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jeremy Cline correctly points out in rhbz#1514836 that a device where the
QCA rome chipset needs the USB_QUIRK_RESET_RESUME quirk, may also ship
with a different wifi/bt chipset in some configurations.
If that is the case then we are needlessly penalizing those other chipsets
with a reset-resume quirk, typically causing 0.4W extra power use because
this disables runtime-pm.
This commit moves the DMI table check to a btusb_check_needs_reset_resume()
helper (so that we can easily also call it for other chipsets) and calls
this new helper only for QCA_ROME chipsets for now.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Cc: stable@vger.kernel.org
Cc: Jeremy Cline <jcline@redhat.com>
Suggested-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit f44cb4b19e ("Bluetooth: btusb: Fix quirk for Atheros
1525/QCA6174") is causing bluetooth to no longer work for several
people, see: https://bugzilla.redhat.com/show_bug.cgi?id=1568911
So lets revert it for now and try to find another solution for
devices which need the modified quirk.
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA Rome controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Vic Wei <vwei@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As Interrupt resource specified IRQs are now assumed to be always
active-low the DMI quirk for the MINIX Z83-4 is no longer required.
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With patch 279c936153 the btuart_cs driver has been deprecated in
favor of serial_cs + hci_uart combination.
static struct pcmcia_device_id btuart_ids[] = {
/* don't use this driver. Use serial_cs + hci_uart instead */
PCMCIA_DEVICE_NULL
};
Intead of keeping it around, just remove it since it is not even
assigned to any PCMCIA identifiers anymore.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When adding the alignment and padding support for H:4 packet processing
for the Nokia driver, it broke the h4_recv_buf usage within bpa10x
driver. To fix this use a separate helper function and placing it into a
dedicated h4_recv.h header file.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCILL or eHCILL protocol from TI is actually an H:4 protocol with a
few extra events and thus can also use the h4_recv_buf helper. Instead
of open coding the same funtionality add the extra events to the packet
description table and use h4_recv_buf.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that we need just an ACPI HID in the table, and the driver auto-
configures itself otherwise, we can easily add a bunch of known ACPI HIDs.
This avoids having to add these 1 by 1 as devices with one are encountered
by users.
This commit may seem as if it simply adds all IDs between BCM2E00-BCM2EAC,
but that is not true, all these IDs were found in actual .inf files and
the range is not entirely continuous, the following IDs are not added:
BCM2E6A, BCM2E6C, BCM2E8F and BCM2E91 because I did not see these in any
.inf files. As for the large amount of IDs this seems to be caused by
Broadcom using a separate ID for every bluetooth module using their
chips. E.g. BCM2EA6 seems to be specifically for the Raspberry Pi 3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since I've been doing a lot of work on Linux Bay Trail / Cherry Trail
support, I've gathered a collection of ACPI DSDTs from about 50 such
machines.
Looking at these DSTDs many have an ACPI device entry describing a bcm
bluetooth device (often disabled in the DSDT), quite a few of these ACPI
device entries have a resource-table where the order does not match with
the order currently associated with the HID of that entry in the
bcm_acpi_match table.
Looking at the Windows .inf files, there is nothing indicating a specific
order there, so I believe that there is no 1:1 mapping between the ACPI
HID and the order in which the resources are listed.
Therefor this commit replaces the hardcoded mapping based on ACPI HID,
with code which actually checks in which order the resources are listed
and bases the gpio-mapping on that.
This should ensure that we always pick the right mapping and this will
make adding new ACPI HIDs to the driver easier.
This has been tested on the following devices:
-Asus T100CHI BCM2E39 / brcmfmac43241b4-sdio / BCM4324B3-37.4M.hcd
-Asus T100TA BCM2E39 / brcmfmac43241b4-sdio / BCM4324B3-37.4M.hcd
-Asus T200TA BCM2E65 / brcmfmac43340-sdio / BCM43341B0-37.4M.hcd
-Jumper ezPad mini 3 BCM2E74 / brcmfmac43430a0-sdio / BCM4343A0-26M.hcd
-Acer Iconia Tab8 w1-8 BCM2E83 / brcmfmac4330-sdio / BCM4330B1-26M.hcd
-Chuwi Vi8 plus(CWI519) BCM2EAA / brcmfmac43430-sdio / BCM43430A1-26M.hcd
Which together cover all 3 combinations of using an Interrupt resource /
GpioInt resource as first resource / GpioInt resource as last resource.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We declare the same set of const acpi_gpio_params twice with different
names, besides the needless duplication this naming leads to a sortof
double indirection which also makes it harder to see how the mapping is
actually setup.
This commit renames the first set to have generic names, which better
describe the contents of the mapping and drops the second set.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add 6 new ACPI HIDs to enable bluetooth on devices using these HIDs,
I've tested the following HIDs / devices:
BCM2E74: Jumper ezPad mini 3
BCM2E83: Acer Iconia Tab8 w1-810
BCM2E90: Meegopad T08
BCM2EAA: Chuwi Vi8 plus (CWI519)
The reporter of Red Hat bugzilla 1554835 has tested:
BCM2E84: Lenovo Yoga2
The reporter of kernel bugzilla 274481 has tested:
BCM2E38: Toshiba Encore
Note the Lenovo Yoga2 and Toshiba Encore also needs the earlier patch to
treat all Interrupt ACPI resources as active low.
Cc: stable@vger.kernel.org
Buglink: https://bugzilla.kernel.org/attachment.cgi?id=274481
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1554835
Reported-and-tested-by: Robert R. Howell <rhowell@uwyo.edu>
Reported-and-tested-by: Christian Herzog <daduke@daduke.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Older devices with a serdev attached bcm bt hci, use an Interrupt ACPI
resource to describe the IRQ (rather then a GpioInt resource).
These device seem to all claim the IRQ is active-high and seem to all need
a DMI quirk to treat it as active-low. Instead simply always assume that
Interrupt resource specified IRQs are always active-low.
This fixes the bt device not being able to wake the host from runtime-
suspend on the: Asus T100TAM, Asus T200TA, Lenovo Yoga2 and the Toshiba
Encore, without the need to add 4 new DMI quirks for these models.
This also allows us to remove 2 DMI quirks for the Asus T100TA and Asus
T100CHI series. Likely the 2 remaining quirks can also be removed but I
could not find a DSDT of these devices to verify this.
Cc: stable@vger.kernel.org
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=198953
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1554835
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The struct hcill_cmd to create an skb with a single u8 is pointless. So
just use skb_put_u8 instead.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The variable "payload" will eventually be set to an appropriate pointer
a bit later. Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The local variable "ret" will be set to an appropriate value a bit later.
Thus omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In case the shutdown GPIO is not wired up, it is impossible to reset the
Bluetooth controller to its original state. This include the initial
default baud rate which leads to issues when reloading the module or
when something unexpected happens. To avoid any kind of runtime
deadlocks, stick with the initial default baud rate.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some GPIO controller drivers request sleepable context and so can't
be accessed from IRQ context. Using gpiod_set/get_value accessors
with such controller leads to a kernel warning since they are
reserved for atomic context (according to the documentation).
Use the postfixed _cansleep version instead, indicating that context
is safe for sleeping if necessary. Note that this is the case here
since we never toggle the gpio neither from IRQ nor from a spinlocked
section.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The linkage between the bluetooth driver and the wireless
driver is not defined properly, leading to build problems
such as:
warning: (BT_HCIRSI) selects RSI_COEX which has unmet direct dependencies (NETDEVICES && WLAN && WLAN_VENDOR_RSI && BT_HCIRSI && RSI_91X)
drivers/net/wireless/rsi/rsi_91x_main.o: In function `rsi_read_pkt':
(.text+0x205): undefined reference to `rsi_bt_ops'
As the dependency is actually the reverse (RSI_91X uses
the BT_RSI driver, not the other way round), this changes
the dependency to match, and enables the bluetooth driver
from the RSI_COEX symbol.
Fixes: 38aa4da504 ("Bluetooth: btrsi: add new rsi bluetooth driver")
Acked-by; Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJatkBHAAoJEG4XJFUm622bKuwH/1cPOfTDDd/kFdRSht0rkj0J
PJ+OxdlbnPuXU7R9juDo5r3WeNoyiXvsdKNYGchn9XIEq2BN1jzOzcE7FYs1IwKs
UPZ6gUgF4+wD5eL1tmiWd+P8CSMVVYAdUGE+CjXOdUT08s5NsIm4Uv86ry/nm7gI
DkrkdlRjqDb6Dx8M35kX9AguR1QHz2KmOu2htPomHzDONrD99z8FaqZQHg4oyNAX
yIvidDcDRYmMoHfkifJiuuUxnRgD935tM6QECYjGKXLnCDb9KklCaabe77lAH39M
EGI7Z6teZrvv5IozpGgPnUjr+hjgoiXxfQmFyXOZAmuSDHbxudYMfOd7KtQ18W0=
=ySDb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
The biggest changes are the bluetooth related patches to the rsi
driver. It adds a new bluetooth driver which communicates directly
with the wireless driver and the interface is defined in
include/net/rsi_91x.h.
Major changes:
wl1251
* read the MAC address from the NVS file
rtlwifi
* enable mac80211 fast-tx support
mt76
* add capability to select tx/rx antennas
mt7601
* let mac80211 validate rx CCMP Packet Number (PN)
rsi
* bluetooth: add new btrsi driver
* btcoex support with the new btrsi driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The IRQ output of the bcm bt-device is really a level IRQ signal, which
signals a logical high as long as the device's buffer contains data. Since
the draining in the buffer is done in the tty driver, we cannot (easily)
wait in a threaded interrupt handler for the draining, after which the
IRQ should go low again.
So instead we treat the IRQ as an edge interrupt. This opens the window
for a theoretical race where we wakeup, read some data and then autosuspend
*before* the IRQ has gone (logical) low, followed by the device just at
that moment receiving more data, causing the IRQ to stay high and we never
see an edge.
Since we call pm_runtime_mark_last_busy() on every received byte, there
should be plenty time for the IRQ to go (logical) low before we ever
suspend, so this should never happen, but after commit 43fff76834
("Bluetooth: hci_bcm: Streamline runtime PM code"), which has been reverted
since, this was actually happening causing the device to get stuck in
runtime suspend.
The bcm bt-device actually has a workaround for this, if we set the
pulsed_host_wake flag in the sleep parameters, then the device monitors
if the host is draining the buffer and if not then after a timeout the
device will pulse the IRQ line, causing us to see an edge, fixing the
stuck in suspend condition.
This commit sets the pulsed_host_wake flag to fix the (mostly theoretical)
race caused by us treating the IRQ as an edge IRQ.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit 43fff76834 ("Bluetooth: hci_bcm: Streamline runtime
PM code"). The commit msg for this commit states "No functional change
intended.", but replacing:
pm_runtime_get();
pm_runtime_mark_last_busy();
pm_runtime_put_autosuspend();
with:
pm_request_resume();
Does result in a functional change, pm_request_resume() only calls
pm_runtime_mark_last_busy() if the device was suspended before the call.
This results in the following happening:
1) Device is runtime suspended
2) Device drives host_wake IRQ logically high as it starts receiving data
3) bcm_host_wake() gets called, causes the device to runtime-resume,
current time gets marked as last_busy time
4) After 5 seconds the autosuspend timer expires and the dev autosuspends
as no one has been calling pm_runtime_mark_last_busy(), the device was
resumed during those 5 seconds, so all the pm_request_resume() calls
while receiving data and/or bcm_host_wake() calls were nops
5) If 4) happens while the device has (just received) data in its buffer to
be read by the host the IRQ line is *already* / still logically high
when we autosuspend and since we use an edge triggered IRQ, the IRQ
will never trigger, causing the device to get stuck in suspend
Therefor this commit has to be reverted, so that we avoid the device
getting stuck in suspend.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Redpine bluetooth driver is a thin driver which depends on
'rsi_91x' driver for transmitting and receiving packets
to/from device. It creates hci interface when attach() is
called from 'rsi_91x' module.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1fdb926974 ("Bluetooth: btusb: Use DMI matching for QCA
reset_resume quirking"), added the Lenovo Yoga 920 to the
btusb_needs_reset_resume_table.
Testing has shown that this is a false positive and the problems where
caused by issues with the initial fix: commit fd865802c6 ("Bluetooth:
btusb: fix QCA Rome suspend/resume"), which has already been reverted.
So the QCA Rome BT in the Yoga 920 does not need a reset-resume quirk at
all and this commit removes it from the btusb_needs_reset_resume_table.
Note that after this commit the btusb_needs_reset_resume_table is now
empty. It is kept around on purpose, since this whole series of commits
started for a reason and there are actually broken platforms around,
which need to be added to it.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1514836
Fixes: 1fdb926974 ("Bluetooth: btusb: Use DMI matching for QCA ...")
Cc: stable@vger.kernel.org
Cc: Brian Norris <briannorris@chromium.org>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kevin Fenzi <kevin@scrye.com>
Suggested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the devicetree binding the shutdown and device wake
GPIOs are optional. Since commit 3e81a4ca51 ("Bluetooth: hci_bcm:
Mandate presence of shutdown and device wake GPIO") this driver
won't probe anymore on Raspberry Pi 3 and Zero W (no device wake GPIO
connected). So fix this regression by reverting this commit partially.
Fixes: 3e81a4ca51 ("Bluetooth: hci_bcm: Mandate presence of shutdown and device wake GPIO")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-02-15
Here's the first bluetooth-next pull request targetting the 4.17 kernel
release.
- Fixes & cleanups to Atheros and Marvell drivers
- Support for two new Realtek controllers
- Support for new Intel Bluetooth controller
- Fix for supporting multiple slave-role Bluetooth LE connections
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Bluetooth parts of RTL8723D and RTL8723B share the same lmp
subversion, thus we need to check both lmp subversion and hci revision
to distinguish the two. The same situation is true for RTL8821A and
RTL8821C. Accordingly, the selection code is revised.
To improve maintainability, a new id_table struct is defined, and an
array of such structs is constructed. Adding a new device can thus be
as simple as adding another value to the table.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Asus Z370-I contains a Realtek RTL8822BE device with an associated
BT chip using a USB ID of 0b05:185c. This device is added to the driver.
Signed-off-by: Hon Weng Chong <honwchong@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
download_firmware() is never called from atomic context.
It is only called by ll_setup() that is called only via function pointer
"->setup" used in hci_uart_setup() in drivers/bluetooth/hci_serdev.c and
drivers/bluetooth/hci_ldisc.c. hci_uart_setup() is called only
via function pointer "->setup" used in hci_dev_do_open()
in net/bluetooth/hci_core.c.
All of the above functions do not enter atomic context.
Besides, ll_setup() calls msleep() and hci_dev_do_open calls mutex_lock().
So it indicates that all the above functions call functions that can sleep.
Despite never getting called from atomic context, download_firmware()
calls mdelay() for busy wait.
That is not necessary and can be replaced with msleep to avoid busy wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After checking all possible call chains to btmrvl_send_sync_cmd(),
my tool finds that this function is never called in atomic context,
namely never in an interrupt handler or holding a spinlock.
And it calls wait_event_interruptible_timeout() after bt_skb_alloc(),
so it indicates that btmrvl_send_sync_cmd()
can call function which can sleep.
Thus GFP_ATOMIC is not necessary, and it can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
ath_wakeup_ar3k() is never called from atomic context.
It is only called by ath_hci_uart_work() that is only called in
ath_open() via INIT_WORK().
All of the above functions do not enter atomic context along the way.
Despite never getting called from atomic context, ath_wakeup_ar3k() calls
mdelay() for busy wait.
That is not necessary and can be replaced with msleep to avoid busy wait.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch fixed warning:
WARNING: Prefer using '"%s...", __func__' to using 'ath3k_disconnect', this function's name, in a string
#568: FILE: drivers/bluetooth/ath3k.c:568:
+ BT_DBG("ath3k_disconnect intf %p", intf);
Signed-off-by: Maxim Zhukov <mussitantesmortem@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Do not need to initialize variables, because further on the code they
fall into the snprintf.
Signed-off-by: Maxim Zhukov <mussitantesmortem@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replaced the numbers with a readable define.
Signed-off-by: Maxim Zhukov <mussitantesmortem@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
