Inserting IPv6 CFP rules complicates the code a little bit in that we
need to insert two rules side by side and chain them to match a full
IPv6 tuple (src, dst IPv6 + port + protocol).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bcm_sf2 EEE-related functions to the b53 driver because this is shared
code amongst Gigabit capable switch, only 5325 and 5365 are too old to support
that.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7278 has only 128 entries while BCM7445 has the full 256 entries set,
fix that.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Starfigther 2 driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring classification rules using the
ethtool::rxnfc API. This is useful to program the switch's CFP/TCAM to
redirect specific packets to specific ports/queues for instance. For
now, we allow any kind of IPv4 5-tuple matching.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse the "brcm,use-bcm-hdr" boolean property during ports
identification to fill a bitmask of ports that should have Broadcom tags
enabled. This is needed in some configurations where per-packet metadata
can be exchanged using Broadcom tags between the switch and an on-chip
acceleration device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting a new device with a slightly different
register layout, affecting the SWITCH_REG and SWITCH_CORE address
spaces, perform a few preparatory steps:
- allow matching the compatible string against a data description
- convert the SWITCH_REG register accesses into an indirection table
- prepare for supporting a SWITCH_CORE register alignment requirement
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point inlining the 32-bit direct register read/write part,
just infer it from the existing macro. This will make it easier to
centralize the address rewriting that we are going to introduce later
on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While migrating the bcm_sf2 driver to use b53_common, we left a small
piece untouched where we kept our local copy of the per-port
port_vlan_ctl bitmask value. This value is now maintained by b53_device
so we need to use it instead of our local (and now stale) copy of it.
Fixes: f458995b9a ("net: dsa: bcm_sf2: Utilize core B53 driver when possible")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access the priv member of the dsa_switch structure directly, instead of
having an unnecessary helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we are using b53_common for most VLAN, FDB and bridge
operations, delete all the redundant code that we had in bcm_sf2.c to
keep only the integration specific logic that we have to deal with:
power management, link management and the external interfaces (RGMII,
MDIO).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom Starfighter2 is almost entirely register compatible with
B53, yet for historical reasons came up first in the tree and is now
being updated to utilize b53_common.c to the fullest extent possible. A
few things need to be adjusted to allow that:
- the switch "core" registers currently operate on a 32-bit address,
whereas b53 passes a page + reg pair to offset from, so we need to
convert that, thankfully there is a generic formula to do that
- the link managemenent is not self contained with the B53/CORE register
set, but instead is in the SWITCH_REG block which is part of the
integration glue logic, so we keep that entirely custom here because
this really is part of the existing bcm_sf2 implementation
- there are additional power management constraints on the port's
memories that make us keep the port_enable/disable callbacks custom
for now, also, we support tagging whereas b53_common does not support
that yet
All the VLAN and bridge code is entirely identical though so, avoid
duplicating it. Other things will be migrated in the future like EEE and
possibly Wake-on-LAN.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We kept shadow copies of which interrupt sources we have enabled and
disabled, but due to an order bug in how intrl2_mask_clear was defined,
we could run into the following scenario:
CPU0 CPU1
intrl2_1_mask_clear(..)
sets INTRL2_CPU_MASK_CLEAR
bcm_sf2_switch_1_isr
read INTRL2_CPU_STATUS and masks with stale
irq1_mask value
updates irq1_mask value
Which would make us loop again and again trying to process and interrupt
we are not clearing since our copy of whether it was enabled before
still indicates it was not. Fix this by updating the shadow copy first,
and then unasking at the HW level.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring VLANs on the Broadcom Starfigther2 switch.
This is all done through the bridge vlan facility just like other DSA
drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register a slave MDIO bus which allows us to divert problematic
read/writes towards conflicting pseudo-PHY address (30). Do no longer
rely on DSA's slave_mii_bus, but instead provide our own implementation
which offers more flexibility as to what to do, and when to register it.
We need to register it by the time we are able to get access to our
memory mapped registers, which is not until drv->setup() time. In order
to avoid forward declarations, we need to re-order the function bodies a
bit.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some DSA drivers may or may not support multiple software bridges on top
of an hardware switch.
It is more convenient for them to access the bridge's net_device for
finer configuration.
Removing the need to craft and access a bitmask also simplifies the
code.
This patch changes the signature of bridge related functions, update DSA
drivers, and removes dsa_slave_br_port_mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the current driver mostly supports BCM7445 which has a hardcoded
location for its MoCA port on port 7 and port 0 for its internal PHY,
this is not necessarily true for all other chips out there such as
BCM3390 for instance.
Walk the list of ports from Device Tree, get their port number ("reg"
property), and then parse the "phy-mode" property and initialize two
internal variables: moca_port and a bitmask of internal PHYs. Since we
use interrupts for the MoCA port, we introduce two helper functions to
enable/disable interrupts and do this at the appropriate bank (INTRL2_0
or INTRL2_1).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.
The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro to write 64-bits quantities to the 32-bits register swapped
the value and offsets arguments, we want to preserve the ordering of the
arguments with respect to how writel() is implemented for instance:
value first, offset/base second.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the bridge join, leave and set_stp callbacks by making that
we do the following:
- when a port joins the bridge, all existing ports in the bridge get
their VLAN control register updated with that joining port
- the joining port is including all existing bridge ports in its own
VLAN control register
The leave operation is fairly similar, special care must be taken to
make sure that port leaving the bridging is not removing itself from its
own VLAN control register.
Since the various BR_* states apply directly to our HW semantics, we
just need to translate these constants into their corresponding HW
settings, and voila!
We make sure to trigger a fast-ageing process for ports that are
joining/leaving the bridge and transition from incompatible states, this
is equivalent to triggering an ARL flush for that port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading 64-bits register was not working because we inverted the steps
between reading the lower 32-bits of the register and reading the upper
32-bits. Swapping these operations is how the HW guarantees that 64-bits
reads are latched correctly. We only have a handful of 64-bits registers
for now, mostly MIB counters, so the imapct is low.
Fixes: 246d7f773c ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When EEE is enabled, negotiate this feature with the PHY and make sure
that the capability checking, local EEE advertisement, link partner EEE
advertisement and auto-negotiation resolution returned by phy_init_eee()
is positive, and enable EEE at the switch level.
While querying the current EEE settings, verify the low-power indication
and indicate its status.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for Wake-on-LAN to work properly, we query the parent network
device Wake-on-LAN features and advertise those. Similarly, when
configuring Wake-on-LAN on a per-port network interface, we make sure
that we do not accept something the master network devices does not
support.
Finally, we need to maintain a bitmask of the ports enabled for
Wake-on-LAN to prevent the suspend() callback from disabling a port that
is used for waking up the system.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated BCM7xxx PHY contains no useful revision information
in its MII_PHYSID2 bits 3:0, that information is instead contained in
the SWITCH_REG_PHY_REVISION register.
Read this register, store its value, and return it by implementing the
dsa_switch::get_phy_flags() callback accordingly. The register layout is
already matching what the BCM7xxx PHY driver is expecting to find.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom Starfigther 2 switch chip using a DSA
driver. This switch driver supports the following features:
- configuration of the external switch port interface: MII, RevMII,
RGMII and RGMII_NO_ID are supported
- support for the per-port MIB counters
- support for link interrupts for special ports (e.g: MoCA)
- powering up/down of switch memories to conserve power when ports are
unused
Finally, update the compatible property for the DSA core code to match
our switch top-level compatible node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
