Add a new host controller driver method, reset_device(), that the USB core
will use to notify the host of a successful device reset. The call may
fail due to out-of-memory errors; attempt the port reset sequence again if
that happens. Update hub_port_init() to allow resetting a configured
device.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is reset, the xHCI hardware must know, in order to match
the device state and disable all endpoints except control endpoint 0.
Issue a Reset Device command after a USB device is successfully reset.
Wait on the command to finish, and then cache or free the disabled
endpoint rings.
There are four different USB device states that the xHCI hardware tracks:
- disabled/enabled - device connection has just been detected,
- default - the device has been reset and has an address of 0,
- addressed - the device has a non-zero address but no configuration has
been set,
- configured - a set configuration succeeded.
The USB core may issue a port reset when a device is in any state, but the
Reset Device command will fail for a 0.96 xHC if the device is not in the
addressed or configured state. Don't consider this failure as an error,
but don't free any endpoint rings if this command fails.
A storage driver may request that the USB device be reset during error
handling, so use GPF_NOIO instead of GPF_KERNEL while allocating memory
for the Reset Device command.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the hub emulation code to allow ports on an xHCI root hub to be
disabled. Add the code to clear the port enabled/disabled bit, and clear
the port enabled/disabled change bit. Like EHCI, the port cannot be
enabled by setting the port enabled/disabled bit. Instead, a port is
enabled by the host controller after a reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor the code to clear the port change bits in the port status
register. All port status change bits are write one to clear.
Remove a redundant port status read that was supposed to unblock any
posted writes. We read the port after the write to get the updated status
for debugging, so the port read after that is unnecessary.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All commands that can be issued to the xHCI hardware can come back with
vendor-specific "informational" completion codes. These are to be treated
like a successful completion code. Refactor out the code to test for the
range of these codes and print debugging messages.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xhci_command structure is the basic structure for issuing commands to
the xHCI hardware. It contains a struct completion (so that the issuing
function can wait on the command), command status, and a input context
that is used to pass information to the hardware. Not all commands need
the input context, so make it optional to allocate. Allow
xhci_free_container_ctx() to be passed a NULL input context, to make
freeing the xhci_command structure simple.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor out the code to cache or free endpoint rings from recently
dropped or disabled endpoints. This code will be used by a new function
to reset a device and disable all endpoints except control endpoint 0.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we fail to queue an evaluate context command or a configure endpoint
command to the command ring in xhci_configure_endpoint(), we need to
remove the xhci_command structure from the device's command list before
returning. If the command is left on the command list, it will sit there
indefinitely, blocking commands submitted after this fails.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1316) adds some error checking to usb_submit_urb().
It's conditional on CONFIG_USB_DEBUG, so it won't affect normal users.
The new check makes sure that the actual type of the endpoint
described by urb->pipe agrees with the type encoded in the pipe value.
The USB error code documentation is updated to include the code
returned by the new check, and the usbfs SUBMITURB handler is updated
to use the correct pipe type when legacy user code tries to submit a
bulk transfer to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My distro kernel (Fedora Rawhide) started throwing warnings from DMA API
checker, so I have no choice but band-aid it quick. There's no attempt
to reuse DMA buffers. Control messages are only sent rarely anyway.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hardware reports wrong interrupt. Although such a situation should not
happen, the compiler complains about this access.
This patch adds a sanity check and generates warning to detect such
issues.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On various mxc boards, the intial ULPI reads resulted in a timeout
which prevented the transceiver to be identified and thus the ehci
device to be probed.
Initializing the hardware lines connected to the transceiver (through
pdata->init call) before actually enabling clocks and configuring
registers in the devices fixes this problem.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed CS5 and CS6 from data bits since these are not supported
in FTDI hardware.
Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Latency timeout was read but never stored on port probe. When
ASYNC_LOW_LATENCY was cleared the device timeout would get set to 0
rather than the default 16ms.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We always push characters to ldisc immediately regardless of
ASYNC_LOW_LATENCY.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resubmitting read urb fails with -EPERM if completion handler runs while
urb is being killed on close. This should not be reported as an error.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changes:
Return an empty string for modulation
when there is no connection
Fix sysfs unload race conditions
Log firmware load process, remove delay
Add new configuration interface
Remove cxacru-cf.bin
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This has never worked properly because wsize passed to
cxacru_cm() is incorrectly set to the number of values
instead of the data bytes. The maximum number of values
that can be set at once is 7 which means the device will
not get enough data to work with and none of the
configuration values will be used.
At least one existing cxacru-cf.bin file contains invalid
data which will prevent the modem from syncing properly.
Fixing it is likely to break existing systems, and the
new sysfs interface for setting configuration parameters
can provide the same functionality. A script is provided
to convert from the original format.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modem can be configured using CM_REQUEST_CARD_DATA_SET,
although CM_REQUEST_CARD_DATA_GET does not return any data.
Tested by setting the modulation (0x0a) option.
There is a list of parameters in the following archive,
but the meaning of many of them is not well documented:
http://sourceforge.net/project/shownotes.php?release_id=301825
This source also indicates that the highest parameter set
is 0x4a but this varies by model so an arbitrary limit of
0x7f has been used (the index is a 32-bit integer).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Firmware writing takes 256ms per 4KB with OHCI, which
is very slow compared to 7ms per 4KB with UHCI.
Until I have access to a hardware USB analyser it may
not be possible to determine why this happens.
Instead of appearing to do nothing, log progress when
writing firmware and then log the ATM device information
when finished. Remove an unnecessary 4 second delay.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These commands were found by accident... fortunately
it still works even if the flash memory is erased,
despite having no USB device IDs.
Some example sysfs code for raw command access:
http://simon.arlott.org/pub/cxacru/raw.c
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is possible for usb_get_intfdata() to return NULL if
sysfs is accessed while the module is being unloaded or
the device is being removed.
Move the access code to an inline function in usbatm.h,
and return -ENODEV if any of the pointers are NULL.
It should not be possible for the instance data or atm
device to be invalid until after unbind() completes and
the sysfs attributes have been removed.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When attempting to read data that is not actually
an array of values, the length may be negative
which causes an Oops due to a likely access off
the end of the data array.
This bug should not occur under normal use unless
the device returns an invalid response.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there is no connection, return an empty string
instead of "0" for the connection modulation.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a Full / Low speed only USB host for the i.MX21.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
block: don't access jiffies when initialising io_context
cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
block: fix for "Consolidate phys_segment and hw_segment limits"
cfq-iosched: quantum check tweak
blktrace: perform cleanup after setup error
blkdev: fix merge_bvec_fn return value checks
cfq-iosched: requests "in flight" vs "in driver" clarification
cciss: Fix problem with scatter gather elements in the scsi half of the driver
cciss: eliminate unnecessary pointer use in cciss scsi code
cciss: do not use void pointer for scsi hba data
cciss: factor out scatter gather chain block mapping code
cciss: fix scatter gather chain block dma direction kludge
cciss: simplify scatter gather code
cciss: factor out scatter gather chain block allocation and freeing
cciss: detect bad alignment of scsi commands at build time
cciss: clarify command list padding calculation
cfq-iosched: rethink seeky detection for SSDs
cfq-iosched: rework seeky detection
block: remove padding from io_context on 64bit builds
block: Consolidate phys_segment and hw_segment limits
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (252 commits)
ASoC: Check progress when reporting periods from i.MX FIQ handler
ASoC: Remove a unused variables from i.MX FIQ runtime data
ALSA: hda - Add/fix ALC269 FSC and Quanta models
ALSA: hda - Add ALC670 codec support
OMAP4: PMIC: Add support for twl6030 codec
ALSA: hda - remove unnecessary msleep on power state transitions
usb/gadget/{f_audio,gmidi}.c: follow recent changes in audio.h
ASoC: fsi: Modify over/under run error settlement
ASoC: OMAP4: Add McPDM platform driver
ASoC: OMAP4: Add support for McPDM
ASoC: OMAP: data_type and sync_mode configurable in audio dma
ALSA: hda - Add missing description in HD-Audio-Models.txt
ALSA: add support for Macbook Air 2,1 internal speaker
ALSA: usbaudio: consolidate header files
ALSA: usbmixer: bail out early when parsing audio class v2 descriptors
ALSA: usbaudio: implement basic set of class v2.0 parser
ALSA: usbaudio: introduce new types for audio class v2
ALSA: usbaudio: parse USB descriptors with structs
ALSA: hda - enable snoop for Intel Cougar Point
ALSA: hda - Remove identical definitions for macmini3 model
...
Set power.async_suspend for USB devices, endpoints and interfaces,
allowing them to be suspended and resumed asynchronously during
system sleep transitions.
The power.async_suspend flag is also set for devices that don't have
suspend or resume callbacks, because otherwise they would make the
main suspend/resume thread wait for their "asynchronous" children
(during suspend) or parents (during resume), effectively negating the
possible gains from executing these devices' suspend and resume
callbacks asynchronously.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1331) adds non-tree ordering constraints needed for
proper resume of PCI USB host controllers from hibernation. The main
issue is that non-high-speed devices must not be resumed before the
high-speed root hub, because it is the ehci_bus_resume() routine which
takes care of handing the device connection over to the companion
controller. If the device resume is attempted before the handover
then the device won't be found and it will be treated as though it had
disconnected.
The patch adds a new field to the usb_bus structure; for each
full/low-speed bus this field will contain a pointer to the companion
high-speed bus (if one exists). It is used during normal device
resume; if the hs_companion pointer isn't NULL then we wait for the
root-hub device on the hs_companion bus.
A secondary issue is that an EHCI controlller shouldn't be resumed
before any of its companions. On some machines I have observed
handovers failing if the companion controller is reinitialized after
the handover. Thus, the EHCI resume routine must wait for the
companion controllers to be resumed.
The patch also fixes a small bug in usb_hcd_pci_probe(); an error path
jumps to the wrong label, causing a memory leak.
[rjw: Fixed compilation for CONFIG_PM_SLEEP unset.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The five-second delay can be rather annoying, and makes the system
appear much less responsive when you connect a USB drive.
It's also not entirely clear that it is needed - the settling delay has
at least historically been an issue on some Apple iPods, for example,
and some devices have been reported to need even more than the old 5s
delay.
But before we penalize them all, let's see how bad it really is. Some
of the reasons for long delays seem to be actual historical kernel bugs
that should probably never have been papered over with a delay in the
first place (there's a Ubuntu bug report for 2.6.20 about a NULL pointer
dereference unless 'delay_use' is 8 or more, for example).
It also looks like some distros have already shipped with delay_use=0,
so the five second default may well be totally historical.
In other words: "Let's see if anybody screams".
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Some structs in linux/usb/audio.h have got new names to mark them as
part of version 1.0 of the USB audio standard. Follow these changes
in the gadget drivers.
Note that this header and the ALSA USB driver will undergo some
refactoring soon, so there might be another update to the gadgets as
well.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
eem_wrap() is sending a sentinel CRC, but it didn't indicate that to
the host, it should zero bit 14 (bmCRC) in the EEM packet header,
instead of setting it.
Also remove a redundant crc calculation in eem_unwrap().
Signed-off-by: Steve Longerbeam <stevel@netspectrum.com>
Acked-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With CONFIG_USB_ULPI=y, CONFIG_USB<=m, CONFIG_PCI=n and
CONFIG_USB_OTG_UTILS=n, which is the default used for mx31moboard,
the build for all mx3 platforms fails because drivers/usb/otg/ulpi.c
where otg_ulpi_create is defined is not compiled.
Build error:
arch/arm/mach-mx3/built-in.o: In function `mxc_board_init':
kzmarm11.c:(.init.text+0x73c): undefined reference to `otg_ulpi_create'
kzmarm11.c:(.init.text+0x1020): undefined reference to `otg_ulpi_create'
This isn't a strong dependency as drivers/usb/otg/ulpi.c doesn't
use functions defined in drivers/usb/otg/otg.o and is only needed
to get ulpi.o linked into the kernel image.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
g_multi used CONFIG_USB_ETH_RNDIS to check if RNDIS option was requested
where it should check for CONFIG_USB_G_MULTI_RNDIS. As a result, RNDIS
was never present in g_multi regardless of configuration.
This fixes changes made in commit 396cda90d2.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After kfifo rework FHCI fails to build:
CC drivers/usb/host/fhci-tds.o
drivers/usb/host/fhci-tds.c: In function 'fhci_ep0_free':
drivers/usb/host/fhci-tds.c:108: error: used struct type value where scalar is required
drivers/usb/host/fhci-tds.c:118: error: used struct type value where scalar is required
drivers/usb/host/fhci-tds.c:128: error: used struct type value where scalar is required
This is because kfifos are no longer pointers in the ep struct.
So, instead of checking the pointers, we should now check if kfifo
is initialized.
Reported-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for Dell Computer Corp. Wireless 5720 VZW Mobile
Broadband (EVDO Rev-A) Minicard GPS Port. I stole the name from lsusb,
but my card does not have a GPS on it (at least not that I can make
function). I'm sure the patch is whitespace damaged but the one line
addition should be fairly straightforward nonetheless.
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the USB product ID of KAIREN's USB VGA Adaptor,
USB20SVGA-MB-PLUS, to sisusbvga work with it.
Signed-off-by: Tanaka Akira <akr@fsij.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
1. There are two msleep calls inside two spin lock sections, need to unlock
and lock again after msleep.
2. Save a extra status reg setting.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB gadget controller drivers normally export their driver registration
function, allowing modular builds of the individual gadget drivers so
do so for s3c-hsotg, fixing builds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The build of r8a66597-udc was failing on ARM since IS_ERR() and
PTR_ERR() weren't protyped. Presumably err.h is being pulled in by
another header on other platforms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- add FTDI device IDs for several ELV devices and NXTCam of Lego Mindstorms NXT
- add hopefully helpful new_id comment
- remove less helpful "Due to many user requests for multiple ELV devices we enable
them by default." comment (we simply add _all_ known devices - an
enduser shouldn't have to fiddle with obscure module parameters...).
- add myself to DRIVER_AUTHOR
The missing NXTCam ID has been found at
http://www.unixboard.de/vb3/showthread.php?t=44155
, ELV devices taken from ELV Windows .inf file.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the subclass and protocol entries from a Microtech
entry in unusual_devs.h. This was reported by <ryck@pacbell.net>.
Greg, please apply.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
added new device pid (PAPOUCH_AD4USB_PID) to ftdi_sio.h and ftdi_sio.c
AD4USB measuring converter is a 4-input A/D converter which enables the
user to measure to four current inputs ranging from 0(4) to 20 mA or
voltage between 0 and 10 V. The measured values are then transferred to
a superior system in digital form. The AD4USB communicates via USB.
Powered is also via USB. datasheet in english is here:
http://www.papouch.com/shop/scripts/pdf/ad4usb_en.pdf
Signed-off-by: Radek Liboska <liboska@uochb.cas.cz>
I notice that the processcompl_compat() function seems to be leaking the
'struct async *as' in the error paths.
I think that the calling convention is fundamentally buggered. The
caller is the one that did the "reap_as()" to get the as thing, the
caller should be the one to free it too.
Freeing it in the caller also means that it very clearly always gets
freed, and avoids the need for any "free in the error case too".
From: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Marcus Meissner <meissner@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We need to only copy the data received by the device to userspace, not
the whole kernel buffer, which can contain "stale" data.
Thanks to Marcus Meissner for pointing this out and testing the fix.
Reported-by: Marcus Meissner <meissner@suse.de>
Tested-by: Marcus Meissner <meissner@suse.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current root hub polling code exhibits a spinlock recursion on the
private controller lock. r8a66597_root_hub_control() is called from
r8a66597_timer() which grabs the lock and disables IRQs. The following
chain emerges:
r8a66597_timer() <-- lock taken
r8a66597_root_hub_control()
r8a66597_check_syssts()
usb_hcd_poll_rh_status() <-- acquires the same lock
/* insert death here */
The entire chain requires IRQs to be disabled, so we just unlock and
relock around the call to usb_hcd_poll_rh_status() while leaving the
IRQ state unchanged.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
