Add a node for the UART part of WiLink chip.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For the ti-cpufreq driver we need a clear separation between omap34 and omap36 families
since they have different silicon revisions and efuses.
So far ti,omap3630/ti,omap36xx is just an additional flag to ti,omap3 while omap34 has no
required entry.
Therefore we can not match omap34 boards properly.
This needs to add ti,omap3430 and ti,omap3630 where it is missing.
We also clean up some instances of missing ti,am3517 so that we can rely on
seeing either one of:
ti,am3517
ti,omap3430
ti,omap3630
in addition to ti,omap3.
We leave ti,omap34xx and ti,omap36xx untouched for compatibility.
The script to do the conversion is:
manually fix am3517_mt_ventoux.dts
find arch/arm/boot/dts -name '*.dts*' -exec fgrep -q '"ti,omap34xx"' {} \; ! -exec fgrep -q '"ti,omap3430"' {} \; -exec sed -i '' 's/"ti,omap34xx"/"ti,omap3430", "ti,omap34xx"/' {} \;
find arch/arm/boot/dts -name '*.dts*' -exec fgrep -q '"ti,omap36xx"' {} \; ! -exec fgrep -q '"ti,omap3630"' {} \; -exec sed -i '' 's/"ti,omap36xx"/"ti,omap3630", "ti,omap36xx"/' {} \;
find arch/arm/boot/dts \( -name 'omap*.dts*' -o -name 'logic*.dts*' \) -exec fgrep -q '"ti,omap3"' {} \; ! -exec fgrep -q '"ti,omap3630"' {} \; ! -exec fgrep -q '"ti,omap36xx"' {} \; ! -exec fgrep -q '"ti,am3517"' {} \; ! -exec fgrep -q '"ti,omap34xx"' {} \; ! -exec fgrep -q '"ti,omap3430"' {} \; -exec sed -i '' 's/"ti,omap3"/"ti,omap3430", "ti,omap3"/' {} \;
So if your out-of-tree omap3 board does not show any OPPs, please check
the compatibility entry and update if needed.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wl1835mod.pdf data sheet says this pretty clearly for WL_IRQ line:
"WLAN SDIO out-of-band interrupt line. Set to rising edge (active high)
by default."
And it seems this interrupt can be optionally configured to use falling
edge too since commit bd763482c8 ("wl18xx: wlan_irq: support platform
dependent interrupt types").
On omap4, if the wlcore interrupt is configured as level instead of edge,
L4PER will stop doing hardware based idling after ifconfig wlan0 down is
done and the WL_EN line is pulled down.
The symptoms show up with L4PER status registers no longer showing the
IDLEST bits as 2 but as 0 for all the active GPIO banks and for
L4PER_CLKCTRL. Also the l4per_pwrdm RET count stops increasing in
the /sys/kernel/debug/pm_debug/count.
While there is also probably a GPIO related issue that needs to be
still fixed, this change gets us to the point where we can have L4PER
idling.
I'm guessing wlcore was at some point configured to use level interrupts
because of edge handling issues in gpio-omap. However, with the recent
fixes to gpio-omap the edge interrupts seem to be working just fine.
Let's change it for all omap boards with wlcore interrupt set as level.
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Eyal Reizer <eyalr@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com updated comments a bit for gpio issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
I see that people are still sending emails to my old address (that no
longer exists) since is the one mentioned in the IGEP DTS. Replace it
with my current email address to avoid this.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace all the pdata-quirks for setting wl12xx/wl18xx
platform data with proper DT definitions.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the new hardware revision of the IGEPv2. Basically, the new
revision F replaces the old Wifi module for a Wilink8 based module.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
