Using mod_delayed_work() allows to simplify handling delayed work and
removes the need for the sync parameter in phy_trigger_machine().
Also introduce a helper phy_queue_state_machine() to encapsulate the
low-level delayed work calls. No functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is one step in allowing phylib to make use of link_mode bitmaps,
instead of u32 for supported and advertised features. Convert the phy
drivers to use bitmaps to indicates the features they support.
Build bitmap equivalents of the u32 values at runtime, and have the
drivers point to the appropriate bitmap. These bitmaps are shared, and
we don't want a driver to modify them. So mark them __ro_after_init.
Within phylib, the features bitmap is currently turned back into a
u32. This will be removed once the whole of phylib, and the drivers
are converted to use bitmaps.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phydev_info() and make use of it within the phy drivers and core
code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all new style LINK_MODE bits can be converted into old style
SUPPORTED bits. We need to warn when such a conversion is attempted.
Add a helper for this.
Convert all pr_warn() calls to phydev_warn() where possible.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink has some useful helpers to working with linkmode bitmaps.
Move them to there own header so other code can use them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have MAC drivers open code the test, add a helper in
phylib. This will help when we change the type of phydev->supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when Pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool can be used to enable/disable pause. Add a helper to configure
the PHY when asym pause is supported.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members, add a
helper function for MACs supporting Pause, but not Asym Pause.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for checking whether polling is used to detect PHY status
changes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some network drivers include functionality to speed down the PHY when
suspending and just waiting for a WoL packet because this saves energy.
This functionality is quite generic, therefore let's factor it out to
phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In struct phy_device we have a number of flags being defined as type
bool. Similar to e.g. struct pci_dev we can save some space by using
bit-fields.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c59530d0d5 ("net: Move PHY statistics code into PHY
library helpers") we made net/core/ethtool.c reference symbols which are
part of the library which can be modular. David introduced a temporary
fix with 1ecd6e8ad9 ("phy: Temporary build fix after phylib changes.")
which would prevent such modularity.
This is not desireable of course, so instead, just inline the functions
into include/linux/phy.h to keep both options available.
Fixes: c59530d0d5 ("net: Move PHY statistics code into PHY library helpers")
Fixes: 1ecd6e8ad9 ("phy: Temporary build fix after phylib changes.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make it possible for network device drivers that do not
necessarily have a phy_device attached, but still report PHY statistics,
have a preliminary refactoring consisting in creating helper functions
that encapsulate the PHY device driver knowledge within PHYLIB.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For some phy devices, even though they don't support the MMD extended
register access, it does have some side effect if we are trying to
read/write the MMD registers via indirect method. So introduce general
dummy stubs for MMD register access which these devices can use to avoid
such side effect.
Fixes: b6b5e8a691 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 664fcf123a (net: phy: Threaded interrupts allow some simplification)
the phy_interrupt system was changed to use a traditional threaded
interrupt scheme instead of a workqueue approach.
With this change, the phy status check moved into phy_change, which
did not report back to the caller whether or not the interrupt was
handled. This means that, in the case of a shared phy interrupt,
only the first phydev's interrupt registers are checked (since
phy_interrupt() would always return IRQ_HANDLED). This leads to
interrupt storms when it is a secondary device that's actually the
interrupt source.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the conflicts were cases of overlapping changes.
In net/core/devlink.c, we have to make care that the
resouce size_params have become a struct member rather
than a pointer to such an object.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove a fair amount of duplication in the different 10G PHY
drivers, export all gen10g_* functions to be able to make use of those.
While we are at it, rename gen10g_soft_reset() to gen10g_no_soft_reset()
to illustrate what it does.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
commit f5e64032a7 ("net: phy: fix resume handling") changes the
locking semantics for phy_resume() such that the caller now needs to
hold the phy mutex. Not all call sites were adopted to this new
semantic, resulting in warnings from the added
WARN_ON(!mutex_is_locked(&phydev->lock)). Rather than change the
semantics, add a __phy_resume() and restore the old behavior of
phy_resume().
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: f5e64032a7 ("net: phy: fix resume handling")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the recent introduction of phy_modify add helpers for setting
and clearing bits in PHY registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I see two issues with parameter new_link:
1. It's not needed. See also phy_interrupt(), works w/o this parameter.
phy_mac_interrupt sets the state to PHY_CHANGELINK and triggers the
state machine which then calls phy_read_status. And phy_read_status
updates the link state.
2. phy_mac_interrupt is used in interrupt context and getting the link
state may sleep (at least when having to access the PHY registers
via MDIO bus).
So let's remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phy_modify() convenience accessor to complement the mdiobus
counterpart.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a set of paged phy register accessors which are inherently safe in
their design against other accesses interfering with the paged access.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add unlocked versions of the bus accessors, which allows access to the
bus with all the tracing. These accessors validate that the bus mutex
is held, which is a basic requirement for all mii bus accesses.
Also added is a read-modify-write unlocked accessor with the same
locking requirements.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to convert the result of the autonegotiation advertisment
into the PHYs speed and duplex settings. If the result is full duplex,
also extract the pause mode settings from the link partner advertisment.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add reporting of the MDI swap to the Marvell 10G PHY driver by providing
a generic implementation for the standard 10GBASE-T pair swap register
and polarity register. We also support reading the MDI swap status for
1G and below from a PCS register.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs need the refclk to be a continuous clock. Therefore they don't
allow turning it off and on again during operation. Nonetheless such a
clock switching is performed by some ETH drivers (namely FEC [1]) for
power saving reasons. An example for an affected PHY is the
SMSC/Microchip LAN8720 in "REF_CLK In Mode".
In order to provide a uniform method to overcome this problem this patch
adds a new phy_driver flag (PHY_RST_AFTER_CLK_EN) and corresponding
function phy_reset_after_clk_enable() to the phylib. These should be
used to trigger reset of the PHY after the refclk is switched on again.
[1] commit e8fcfcd568 ("net: fec: optimize the clock management to save power")
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY devices sometimes do have their reset signal (maybe even power
supply?) tied to some GPIO and sometimes it also does happen that a boot
loader does not leave it deasserted. So far this issue has been attacked
from (as I believe) a wrong angle: by teaching the MAC driver to manipulate
the GPIO in question; that solution, when applied to the device trees, led
to adding the PHY reset GPIO properties to the MAC device node, with one
exception: Cadence MACB driver which could handle the "reset-gpios" prop
in a PHY device subnode. I believe that the correct approach is to teach
the 'phylib' to get the MDIO device reset GPIO from the device tree node
corresponding to this device -- which this patch is doing...
Note that I had to modify the AT803x PHY driver as it would stop working
otherwise -- it made use of the reset GPIO for its own purposes...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
[geert: Propagate actual errors from fwnode_get_named_gpiod()]
[geert: Avoid destroying initial setup]
[geert: Consolidate GPIO descriptor acquiring code]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use phy_interface_mode_is_8023z() helper to identify the
interface modes that use 802.3z negotiation. Use it in phylink's
phylink_mac_an_restart().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commits c974bdbc3e "net: phy: Use threaded IRQ, to allow IRQ from
sleeping devices" and 664fcf123a "net: phy: Threaded interrupts allow
some simplification" all relevant code pieces run in process context
anyway and I don't think we need the disabling of interrupts any longer.
Interestingly enough, latter commit already removed the comment
explaining why interrupts need to be temporarily disabled.
On my system phy interrupt mode works fine with this patch.
However I may miss something, especially in the context of shared phy
interrupts, therefore I'd appreciate if more people could test this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
read_status and config_aneg are the only mandatory callbacks and most
of the time the generic implementation is used by drivers.
So make the core fall back to the generic version if a driver doesn't
implement the respective callback.
Also currently the core doesn't seem to verify that drivers implement
the mandatory calls. If a driver doesn't do so we'd just get a NPE.
With this patch this potential issue doesn't exit any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously phy_id was u32 and phy_id_mask was unsigned int. As the
phy_id_mask defines the important bits of the phy_id (and is therefore
the same size) these two variables should be the same data type.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we create a LED trigger for any link speed known to a PHY.
These triggers only fire when their exact link speed had been negotiated
(they aren't cumulative, that is, they don't fire for "their or any higher"
link speed).
What we are missing, however, is a trigger which will fire on any link
speed known to the PHY. Such trigger can then be used for implementing a
poor man's substitute of the "link" LED on boards that lack it.
Let's add it.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, we need to do additional work between the PHY coming up and
marking the carrier present - for example, we may need to wait for the
PHY to MAC link to finish negotiation. This changes phylib to provide
a notification function pointer which avoids the built-in
netif_carrier_on() and netif_carrier_off() functions.
Standard ->adjust_link functionality is provided by hooking a helper
into the new ->phy_link_change method.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_lookup_setting() provides useful functionality in ethtool code
outside phylib. Move it to phy-core and allow it to be re-used (eg,
in phylink) rather than duplicated elsewhere. Note that this supports
the larger linkmode space.
As we move the phy settings table, we also need to move the guts of
phy_supported_speeds() as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other code would like to make use of this, so make the speed and duplex
string generation visible, and place it in a separate file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e5a03bfd87 ("phy: Add an mdio_device structure")
introduced a spurious trailing semicolon. Remove it.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add set_loopback in phy_driver, which is used by MAC
driver to enable or disable phy loopback. it also add a generic
genphy_loopback function, which use BMCR loopback bit to enable
or disable loopback.
Signed-off-by: Lin Yun Sheng <linyunsheng@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Device Tree binding has been updated, update the PHY
library phy_interface_t and phy_modes to support the "internal" PHY
interface type.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4c5e7a2c05 ("dt-bindings: mdio: Clarify binding document")
declared that a MDIO reset GPIO property should have only a single GPIO
reference/specifier, however the supporting code was left intact, still
burdening the kernel with now apparently useless loops -- get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XAUI allows XGMII to reach an extended distance by using a XGXS layer at
each end of the MAC to PHY link, operating over four Serdes lanes.
10GBASE-KR is a single lane Serdes backplane ethernet connection method
with autonegotiation on the link. Some PHYs use this to connect to the
ethernet interface at 10G speeds, switching to other connection types
when utilising slower speeds.
10GBASE-KR is also used for XFI and SFI to connect to XFP and SFP fiber
modules.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_restart_aneg() can only restart autonegotiation on clause 22
PHYs. Add a phy_restart_aneg() function which selects between the
clause 22 and clause 45 restart functionality depending on the PHY
type and whether the Clause 45 PHY supports the Clause 22 register set.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic helpers for 802.3 clause 45 PHYs for >= 10Gbps support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused, so remove it.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet drivers will attach/connect to a PHY device before calling
register_netdevice() which is responsible for calling netdev_register_kobject()
which would do the network device's kobject initialization. In such a case,
sysfs_create_link() would return -ENOENT because the network device's kobject
is not ready yet, and we would fail to connect to the PHY device.
In order to keep things simple and symetrical, we just take the success path as
indicative of the ability to access the network device's kobject, and create
the second link if that's the case.
Fixes: 5568363f0c ("net: phy: Create sysfs reciprocal links for attached_dev/phydev")
Reported-by: Woojung Hung <Woojung.Huh@microchip.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
