Add struct fib_dump_filter for options on limiting which routes are
returned in a dump request. The current list is table id, protocol,
route type, rtm_flags and nexthop device index. struct net is needed
to lookup the net_device from the index.
Declare the filter for each route dump handler and plumb the new
arguments from dump handlers to ip_valid_fib_dump_req.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(the parameter in question is mark)
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NetworkManager likes to manage linklocal prefix routes and does so with
the NLM_F_APPEND flag, breaking attempts to simplify the IPv6 route
code and by extension enable multipath routes with device only nexthops.
Revert f34436a430 and these followup patches:
6eba08c362 ("ipv6: Only emit append events for appended routes").
ce45bded64 ("mlxsw: spectrum_router: Align with new route replace logic")
53b562df8c ("mlxsw: spectrum_router: Allow appending to dev-only routes")
Update the fib_tests cases to reflect the old behavior.
Fixes: f34436a430 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: David Ahern <dsahern@gmail.com>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-05-24
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Björn Töpel cleans up AF_XDP (removes rebind, explicit cache alignment from uapi, etc).
2) David Ahern adds mtu checks to bpf_ipv{4,6}_fib_lookup() helpers.
3) Jesper Dangaard Brouer adds bulking support to ndo_xdp_xmit.
4) Jiong Wang adds support for indirect and arithmetic shifts to NFP
5) Martin KaFai Lau cleans up BTF uapi and makes the btf_header extensible.
6) Mathieu Xhonneux adds an End.BPF action to seg6local with BPF helpers allowing
to edit/grow/shrink a SRH and apply on a packet generic SRv6 actions.
7) Sandipan Das adds support for bpf2bpf function calls in ppc64 JIT.
8) Yonghong Song adds BPF_TASK_FD_QUERY command for introspection of tracing events.
9) other misc fixes from Gustavo A. R. Silva, Sirio Balmelli, John Fastabend, and Magnus Karlsson
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring consistency to ipv6 route replace and append semantics.
Remove rt6_qualify_for_ecmp which is just guess work. It fails in 2 cases:
1. can not replace a route with a reject route. Existing code appends
a new route instead of replacing the existing one.
2. can not have a multipath route where a leg uses a dev only nexthop
Existing use cases affected by this change:
1. adding a route with existing prefix and metric using NLM_F_CREATE
without NLM_F_APPEND or NLM_F_EXCL (ie., what iproute2 calls
'prepend'). Existing code auto-determines that the new nexthop can
be appended to an existing route to create a multipath route. This
change breaks that by requiring the APPEND flag for the new route
to be added to an existing one. Instead the prepend just adds another
route entry.
2. route replace. Existing code replaces first matching multipath route
if new route is multipath capable and fallback to first matching
non-ECMP route (reject or dev only route) in case one isn't available.
New behavior replaces first matching route. (Thanks to Ido for spotting
this one)
Note: Newer iproute2 is needed to display multipath routes with a dev-only
nexthop. This is due to a bug in iproute2 and parsing nexthops.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine path MTU from a FIB lookup result. Logic is based on
ip6_dst_mtu_forward plus lookup of nexthop exception.
Add ip6_dst_mtu_forward to ipv6_stubs to handle access by core
bpf code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree, more relevant updates in this batch are:
1) Add Maglev support to IPVS. Moreover, store lastest server weight in
IPVS since this is needed by maglev, patches from from Inju Song.
2) Preparation works to add iptables flowtable support, patches
from Felix Fietkau.
3) Hand over flows back to conntrack slow path in case of TCP RST/FIN
packet is seen via new teardown state, also from Felix.
4) Add support for extended netlink error reporting for nf_tables.
5) Support for larger timeouts that 23 days in nf_tables, patch from
Florian Westphal.
6) Always set an upper limit to dynamic sets, also from Florian.
7) Allow number generator to make map lookups, from Laura Garcia.
8) Use hash_32() instead of opencode hashing in IPVS, from Vicent Bernat.
9) Extend ip6tables SRH match to support previous, next and last SID,
from Ahmed Abdelsalam.
10) Move Passive OS fingerprint nf_osf.c, from Fernando Fernandez.
11) Expose nf_conntrack_max through ctnetlink, from Florent Fourcot.
12) Several housekeeping patches for xt_NFLOG, x_tables and ebtables,
from Taehee Yoo.
13) Unify meta bridge with core nft_meta, then make nft_meta built-in.
Make rt and exthdr built-in too, again from Florian.
14) Missing initialization of tbl->entries in IPVS, from Cong Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like ip_dst_mtu_maybe_forward(), to avoid a dependency with ipv6.ko.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After 4832c30d54 ("net: ipv6: put host and anycast routes on device
with address") the comparison of idev does not add value since it
correlates to the nexthop device which is already compared. Remove
the idev comparison.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to 4832c30d54 ("net: ipv6: put host and anycast routes on device
with address") host routes and anycast routes were installed with the
device set to loopback (or VRF device once that feature was added). In the
older code dst.dev was set to loopback (needed for packet tx) and rt6i_idev
was used to denote the actual interface.
Commit 4832c30d54 changed the code to have dst.dev pointing to the real
device with the switch to lo or vrf device done on dst clones. As a
consequence of this change ip6_route_get_saddr can just pass the nexthop
device to ipv6_dev_get_saddr.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
addrconf_dst_alloc now returns a fib6_info. Update the name
and its users to reflect the change.
Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the prefix for fib6_info struct elements from rt6i_ to fib6_.
rt6i_pcpu and rt6i_exception_bucket are left as is given that they
point to rt6_info entries.
Rename only; not functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all code paths referencing a FIB entry from
rt6_info to fib6_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last step before flipping the data type for FIB entries:
- use fib6_info_alloc to create FIB entries in ip6_route_info_create
and addrconf_dst_alloc
- use fib6_info_release in place of dst_release, ip6_rt_put and
rt6_release
- remove the dst_hold before calling __ip6_ins_rt or ip6_del_rt
- when purging routes, drop per-cpu routes
- replace inc and dec of rt6i_ref with fib6_info_hold and fib6_info_release
- use rt->from since it points to the FIB entry
- drop references to exception bucket, fib6_metrics and per-cpu from
dst entries (those are relevant for fib entries only)
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 FIB will only contain FIB entries with exception routes added to
the FIB entry. Once this transformation is complete, FIB lookups will
return a fib6_info with the lookup functions still returning a dst
based rt6_info. The current code uses rt6_info for both paths and
overloads the rt6_info variable usually called 'rt'.
This patch introduces a new 'f6i' variable name for the result of the FIB
lookup and keeps 'rt' as the dst based return variable. 'f6i' becomes a
fib6_info in a later patch which is why it is introduced as f6i now;
avoids the additional churn in the later patch.
In addition, remove RTF_CACHE and dst checks from fib6 add and delete
since they can not happen now and will never happen after the data
type flip.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most FIB entries can be added using memory allocated with GFP_KERNEL.
Add gfp_flags to ip6_route_add and addrconf_dst_alloc. Code paths that
can be reached from the packet path (e.g., ndisc and autoconfig) or
atomic notifiers use GFP_ATOMIC; paths from user context (adding
addresses and routes) use GFP_KERNEL.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The router discovery code has a FIB entry and wants to validate the
gateway has a neighbor entry. Refactor the existing dst_neigh_lookup
for IPv6 and create a new function that takes the gateway and device
and returns a neighbor entry. Use the new function in
ndisc_router_discovery to validate the gateway.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce fib6_nh structure and move nexthop related data from
rt6_info and rt6_info.dst to fib6_nh. References to dev, gateway or
lwtstate from a FIB lookup perspective are converted to use fib6_nh;
datapath references to dst version are left as is.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass network namespace reference into route add, delete and get
functions.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move commonly used pattern of ip6_dst_store() usage to a separate
function - ip6_sk_dst_store_flow(), which will check the addresses
for equality using the flow information, before saving them.
There is no functional changes in this patch. In addition, it will
be used in the next patch, in ip6_sk_dst_lookup_flow().
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some operators prefer IPv6 path selection to use a standard 5-tuple
hash rather than just an L3 hash with the flow the label. To that end
add support to IPv6 for multipath hash policy similar to bf4e0a3db9
("net: ipv4: add support for ECMP hash policy choice"). The default
is still L3 which covers source and destination addresses along with
flow label and IPv6 protocol.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 does path selection for multipath routes deep in the lookup
functions. The next patch adds L4 hash option and needs the skb
for the forward path. To get the skb to the relevant FIB lookup
functions it needs to go through the fib rules layer, so add a
lookup_data argument to the fib_lookup_arg struct.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dissect flow in fwd path if fib rules require it. Controlled by
a flag to avoid penatly for the common case. Flag is set when fib
rules with sport, dport and proto match that require flow dissect
are installed. Also passes the dissected hash keys to the multipath
hash function when applicable to avoid dissecting the flow again.
icmp packets will continue to use inner header for hash
calculations.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In early time, when freeing a xdst, it would be inserted into
dst_garbage.list first. Then if it's refcnt was still held
somewhere, later it would be put into dst_busy_list in
dst_gc_task().
When one dev was being unregistered, the dev of these dsts in
dst_busy_list would be set with loopback_dev and put this dev.
So that this dev's removal wouldn't get blocked, and avoid the
kmsg warning:
kernel:unregister_netdevice: waiting for veth0 to become \
free. Usage count = 2
However after Commit 52df157f17 ("xfrm: take refcnt of dst
when creating struct xfrm_dst bundle"), the xdst will not be
freed with dst gc, and this warning happens.
To fix it, we need to find these xdsts that are still held by
others when removing the dev, and free xdst's dev and set it
with loopback_dev.
But unfortunately after flow_cache for xfrm was deleted, no
list tracks them anymore. So we need to save these xdsts
somewhere to release the xdst's dev later.
To make this easier, this patch is to reuse uncached_list to
track xdsts, so that the dev refcnt can be released in the
event NETDEV_UNREGISTER process of fib_netdev_notifier.
Thanks to Florian, we could move forward this fix quickly.
Fixes: 52df157f17 ("xfrm: take refcnt of dst when creating struct xfrm_dst bundle")
Reported-by: Jianlin Shi <jishi@redhat.com>
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Tested-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Before we convert IPv6 to use hash-threshold instead of modulo-N, we
first need each nexthop to store its region boundary in the hash
function's output space.
The boundary is calculated by dividing the output space equally between
the different active nexthops. That is, nexthops that are not dead or
linkdown.
The boundaries are rebalanced whenever a nexthop is added or removed to
a multipath route and whenever a nexthop becomes active or inactive.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, when the carrier of a netdev changes we should toggle
the 'linkdown' flag on all the nexthops using it as their nexthop
device.
This will later allow us to test for the presence of this flag during
route lookup and dump.
Up until commit 4832c30d54 ("net: ipv6: put host and anycast routes on
device with address") host and anycast routes used the loopback netdev
as their nexthop device and thus were not marked with the 'linkdown'
flag. The patch preserves this behavior and allows one to ping the local
address even when the nexthop device does not have a carrier and the
'ignore_routes_with_linkdown' sysctl is set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make IPv6 more in line with IPv4 we need to be able to respond
differently to different netdev events. For example, when a netdev is
unregistered all the routes using it as their nexthop device should be
flushed, whereas when the netdev's carrier changes only the 'linkdown'
flag should be toggled.
Currently, this is not possible, as the function that traverses the
routing tables is not aware of the triggering event.
Propagate the triggering event down, so that it could be used in later
patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch marked nexthops with the 'dead' and 'linkdown' flags.
Clear these flags when the netdev comes back up.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If all dst cache entries are stored in the exception table under the
main route, we have to go through them during fib6_age() when doing
garbage collecting.
Introduce a new function rt6_age_exception() which goes through all dst
entries in the exception table and remove those entries that are expired.
This function is called in fib6_age() so that all dst caches are also
garbage collected.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hash table into struct rt6_info in order to store dst caches
created by pmtu discovery and ip redirect in ipv6 routing code.
APIs to add dst cache, delete dst cache, find dst cache and update
dst cache in the hash table are implemented and will be used in later
commits.
This is a preparation work to move all cache routes into the exception
table instead of getting inserted into the fib6 tree.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forwarding or sending out an ICMPv6 error, look at the embedded
packet that triggered the error and compute a flow hash over its
headers.
This let's us route the ICMP error together with the flow it belongs to
when multipath (ECMP) routing is in use, which in turn makes Path MTU
Discovery work in ECMP load-balanced or anycast setups (RFC 7690).
Granted, end-hosts behind the ECMP router (aka servers) need to reflect
the IPv6 Flow Label for PMTUD to work.
The code is organized to be in parallel with ipv4 stack:
ip_multipath_l3_keys -> ip6_multipath_l3_keys
fib_multipath_hash -> rt6_multipath_hash
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The definition of an "anycast destination address" has been tweaked as a
side-effect of commit 2647a9b070 ("ipv6: Remove external dependency on
rt6i_gateway and RTF_ANYCAST"). The first address of a point-to-point
/127 subnet is now considered as an anycast address. This prevents
ICMPv6 errors to be returned to a sender of such a subnet and breaks
PMTU discovery.
This can be reproduced with:
ip link add name out6 type veth peer name in6
ip link add name out7 type veth peer name in7
ip link set mtu 1400 dev out7
ip link set mtu 1400 dev in7
ip netns add next-hop
ip netns add next-next-hop
ip link set netns next-hop dev in6
ip link set netns next-hop dev out7
ip link set netns next-next-hop dev in7
ip link set up dev out6
ip addr add 2001:db8:1::12/127 dev out6
ip netns exec next-hop ip link set up dev in6
ip netns exec next-hop ip link set up dev out7
ip netns exec next-hop ip addr add 2001:db8:1::13/127 dev in6
ip netns exec next-hop ip addr add 2001:db8:1::14/127 dev out7
ip netns exec next-hop ip route add default via 2001:db8:1::15
ip netns exec next-hop sysctl -qw net.ipv6.conf.all.forwarding=1
ip netns exec next-next-hop ip link set up dev in7
ip netns exec next-next-hop ip addr add 2001:db8:1::15/127 dev in7
ip netns exec next-next-hop ip addr add 2001:db8:1::50/128 dev in7
ip netns exec next-next-hop ip route add default via 2001:db8:1::14
ip netns exec next-next-hop sysctl -qw net.ipv6.conf.all.forwarding=1
ip route add 2001:db8:1::48/123 via 2001:db8:1::13
sleep 4
ping -M do -s 1452 -c 3 2001:db8:1::50 || true
ip route get 2001:db8:1::50
Before the patch, we get:
2001:db8:1::50 from :: via 2001:db8:1::13 dev out6 src 2001:db8:1::12 metric 1024 pref medium
After the patch, we get:
2001:db8:1::50 via 2001:db8:1::13 dev out6 src 2001:db8:1::12 metric 0
cache expires 578sec mtu 1400 pref medium
Fixes: 2647a9b070 ("ipv6: Remove external dependency on rt6i_gateway and RTF_ANYCAST")
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert reported a failure to add different mpls encaps in a multipath
route:
$ ip -6 route add 1234::/16 \
nexthop encap mpls 10 via fe80::1 dev ens3 \
nexthop encap mpls 20 via fe80::1 dev ens3
RTNETLINK answers: File exists
The problem is that the duplicate nexthop detection does not compare
lwtunnel configuration. Add it.
Fixes: 19e42e4515 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reported-by: João Taveira Araújo <joao.taveira@gmail.com>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmp6 dst route is currently ref counted during creation and will be
freed by user during its call of dst_release(). So no need of a garbage
collector for it.
Remove all icmp6 dst garbage collector related code.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a crash on init_net.ipv6.ip6_null_entry->rt6i_idev
since it is always NULL.
This is clearly wrong, we have code to initialize it to loopback_dev,
unfortunately the order is still not correct.
loopback_dev is registered very early during boot, we lose a chance
to re-initialize it in notifier. addrconf_init() is called after
ip6_route_init(), which means we have no chance to correct it.
Fix it by moving this initialization explicitly after
ipv6_add_dev(init_net.loopback_dev) in addrconf_init().
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the UID in routing lookups made by protocol connect() and
sendmsg() functions.
- Make sure that routing lookups triggered by incoming packets
(e.g., Path MTU discovery) take the UID of the socket into
account.
- For packets not associated with a userspace socket, (e.g., ping
replies) use UID 0 inside the user namespace corresponding to
the network namespace the socket belongs to. This allows
all namespaces to apply routing and iptables rules to
kernel-originated traffic in that namespaces by matching UID 0.
This is better than using the UID of the kernel socket that is
sending the traffic, because the UID of kernel sockets created
at namespace creation time (e.g., the per-processor ICMP and
TCP sockets) is the UID of the user that created the socket,
which might not be mapped in the namespace.
Tested: compiles allnoconfig, allyesconfig, allmodconfig
Tested: https://android-review.googlesource.com/253302
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, do not consider link state when validating next hops.
Currently, if the link is down default routes can fail to insert:
$ ip -6 ro add vrf blue default via 2100:2::64 dev eth2
RTNETLINK answers: No route to host
With this patch the command succeeds.
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make ip6_route_input_lookup available outside of ipv6 the module
similar to ip_route_input_noref in the IPv4 world.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VRF driver needs access to ip6_route_get_saddr code. Since it does
little beyond ipv6_dev_get_saddr and ipv6_dev_get_saddr is already
exported for modules move ip6_route_get_saddr to the header as an
inline.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 multicast and link-local addresses require special handling by the
VRF driver:
1. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.
2. fail sends/receives on a VRF device to/from a multicast address
(e.g, make ping6 ff02::1%<vrf> fail)
3. move the setting of the flow oif to the first dst lookup and revert
the change in icmpv6_echo_reply made in ca254490c8 ("net: Add VRF
support to IPv6 stack"). Linklocal/mcast addresses require use of the
skb->dev.
With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses work (icmp, tcp, and udp)
e.g.,
1. packets into VM with VRF config:
ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
ping6 -c3 ff02::1%br1
ssh -6 fe80::e0:f9ff:fe1c:b974%br1
2. packets going out a VRF enslaved device:
ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
ping6 -c3 ff02::1%eth1
ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivek reported a kernel exception deleting a VRF with an active
connection through it. The root cause is that the socket has a cached
reference to a dst that is destroyed. Converting the dst_destroy to
dst_release and letting proper reference counting kick in does not
work as the dst has a reference to the device which needs to be released
as well.
I talked to Hannes about this at netdev and he pointed out the ipv4 and
ipv6 dst handling has dst_ifdown for just this scenario. Rather than
continuing with the reinvented dst wheel in VRF just remove it and
leverage the ipv4 and ipv6 versions.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of ip6_dst_lookup_tail basically
ignore the egress ifindex match: if the saddr is set,
ip6_route_output() purposefully ignores flowi6_oif, due
to the commit d46a9d678e ("net: ipv6: Dont add RT6_LOOKUP_F_IFACE
flag if saddr set"), if the saddr is 'any' the first route lookup
in ip6_dst_lookup_tail fails, but upon failure a second lookup will
be performed with saddr set, thus ignoring the ifindex constraint.
This commit adds an output route lookup function variant, which
allows the caller to specify lookup flags, and modify
ip6_dst_lookup_tail() to enforce the ifindex match on the second
lookup via said helper.
ip6_route_output() becames now a static inline function build on
top of ip6_route_output_flags(); as a side effect, out-of-tree
modules need now a GPL license to access the output route lookup
functionality.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing the np->opt RCU conversion, I found that UDP/IPv6 was
using a mixture of xchg() and sk_dst_lock to protect concurrent changes
to sk->sk_dst_cache, leading to possible corruptions and crashes.
ip6_sk_dst_lookup_flow() uses sk_dst_check() anyway, so the simplest
way to fix the mess is to remove sk_dst_lock completely, as we did for
IPv4.
__ip6_dst_store() and ip6_dst_store() share same implementation.
sk_setup_caps() being called with socket lock being held or not,
we have to use sk_dst_set() instead of __sk_dst_set()
Note that I had to move the "np->dst_cookie = rt6_get_cookie(rt);"
in ip6_dst_store() before the sk_setup_caps(sk, dst) call.
This is because ip6_dst_store() can be called from process context,
without any lock held.
As soon as the dst is installed in sk->sk_dst_cache, dst can be freed
from another cpu doing a concurrent ip6_dst_store()
Doing the dst dereference before doing the install is needed to make
sure no use after free would trigger.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of doing the rt6->rt6i_node check whenever we need
to get the route's cookie. Refactor it into rt6_get_cookie().
It is a prep work to handle FLOWI_FLAG_KNOWN_NH and also
percpu rt6_info later.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
