There are currently no users of the clk_ctrl2_present member from the
platform data, so let's remove it.
Note, as some of the sh_mmcif variants may support clk_ctrl2, let's keep
the current code in the driver, which deals with this. For future support,
we should invent a DT binding instead, but let's leave that until it's
needed.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
There are currently no users of the ccs_unsupported member from the
platform data, so let's remove it.
Note, as some of the sh_mmcif variants may not support ccs, let's keep the
current code in the driver, which deals with this. For future support, we
should invent a DT binding instead, but let's leave that until it's needed.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Removing the callback also enables us to remove the sh_mmcif_get_cd()
altogether, as we convert to use mmc_gpio_get_cd() to the same kind of
work.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The current value means an mdelay(1) may execute up to 10000000 times,
which translates to around ~2.8 hours. This is probably not what the
orignal author had in mind. Let's instead use 10s, which is the same value
sh_mmcif is using for other timeouts.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sh_mmcif driver is already using a 10s request timeout. Let's also
inform the mmc core about this value, as there are situations when it
needs to know about it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sh_mmcif explicity checks for certain commands to decide when to
enable HW busy detection. Instead, it should only check the response type
as it tells if busy detection is needed.
In this way, the mmc core also gets full control whether it thinks busy
detection should be done or not. In some specific scenarios, like for
ERASE and STOP commands it may decide to fall back to use a CMD13 to poll
the card status instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable the capabilities which tells the mmc core to prevent sending SD and
SDIO commands during card initialization. In this way, we can also remove
the validation of non-supported commands in the ->request() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As there are two callers of sh_mmcif_set_power() and because its only
additional action is to check for a valid regulator, let's just remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Both from a runtime PM and clock management point of view, the ->set_ios()
code is unnecessary complex.
A suboptimal path is also executed when the mmc core requests a clock rate
of zero. As that happens during the card initialization phase, trying to
save power by decreasing the runtime PM usage count and gating the clock
via clk_disable_unprepare() is just superfluous.
Moreover, from a runtime PM point of view the core will anyway keep the
device active during the entire card initialization phase.
Restructure the code to rely on the ios->power_mode to understand when the
runtime PM usage count needs to be increased. Let's also deal with clock
rate changes by simply applying the rate.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
While accessing the device, make sure it stays active by increasing the
runtime PM usage count for it.
Let's also defer to enable runtime PM until we really need access to the
device. This also enables the error path in ->probe() to become simpler.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When compiling the sh_mmcif driver for ARM64, we currently
get a harmless build warning:
../drivers/mmc/host/sh_mmcif.c: In function 'sh_mmcif_request_dma_one':
../drivers/mmc/host/sh_mmcif.c:417:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)pdata->slave_id_tx :
^
../drivers/mmc/host/sh_mmcif.c:418:4: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(void *)pdata->slave_id_rx;
This could be worked around by adding another cast to uintptr_t, but
I decided to simplify the code a little more to avoid that. This
splits out the platform data using code into a separate function
and builds that only for CONFIG_SUPERH. This part still has a typecast
but does not need a second one. The SH platform code could be further
modified to pass a pointer directly as we do on other architectures
when we have a filter function.
The normal case is simplified further and now just calls
dma_request_slave_channel() directly without going through the
compat handling.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The clock should be enable when SDHI registers are accessed.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMCIF IP on R-Car series has parent clock which can be set several rate,
and it was not implemented on old SH-Mobile series (= SH-Mobile series
parent clock was fixed rate) R-Car series MMCIF can use more high speed
access if it setups parent clock. This patch adds parent clock setup
method. It will be used if DT has "max-frequency", and then, this driver
assumes it is booted on R-Car Gen2 or later SoC. Because SH-Mobile series
(which doesn't boot from DT) and R-Car series (which boots from DT) have
different divider.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Silence compiler warning]
Current sh_mmcif driver is using sh_mmcif_xxx and mmcif_xxx
for functions. This patch used sh_mmcif_xxx for all functions.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current sh_mmcif driver is directly using &host->pd->dev in all place.
It is not big problem, but it is unreadable, and it can be cause of
future bug. This patch adds new sh_mmcif_host_to_dev() and use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current sh_mmcif_clk_update() is called from probe() and set_ios(),
but, the purpose of later one is just clk_prepare_enable().
No need to setup mmc->f_max/f_min in many times.
This patch separe sh_mmcif_clk_update() into clk_prepare_enable()
and mmc->f_max/f_min setup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct sh_mmcif_host has 1) int clk, 2) struct clock *hclk,
and host->clk = clk_get_rate(host->hclk).
This int clk is not necessary. Let's remove it.
And, current hclk is confusable naming. Let's rename it to clk.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
changed the timeout value from 1000 jiffies to 1s. In the case where
HZ is 1000 the values are the same. However, for smaller HZ values the
timeout is now smaller, 1s instead of 10s in the case of HZ=100.
Since the timeout occurs in spite of a normal data transfer a timeout of
10s seems more appropriate. This restores the previous timeout in the
case where HZ=100 and results in an increase over the previous timeout
for larger values of HZ.
Fixes: f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[horms: rewrote changelog to refer to HZ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A command end interrupt should not be processed between command issue
and setting of wait_for flag. It expects already the flag to be set.
Therefore the exclusive control was added.
Signed-off-by: Kouichi Tomita <kouichi.tomita.yn@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If interruption of command already occurred, mrq pointer in dev_err()
would refer to NULL, because the host-state is changed to STATE_IDLE
and mrq pointer is changed to NULL by interrupt handler.
Therefore dev_err is moved after checking STATE_IDLE.
Signed-off-by: Kouichi Tomita <kouichi.tomita.yn@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current sh_mmcif sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The data register is 4 bytes wide, hardcode the DMA transfer size to
4 bytes in both directions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e5a233cb64 ("mmc: sh_mmcif:
Factorize DMA channel request and configuration code") incorrectly
set the destination address for both slave channels instead of setting
the source address for the receive channel. Fix that.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the error path items that are no longer needed. The mmc card-detect
code cleans up after itself (and registers with devm) and the host error
is the same as the clock disable.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The pm_runtime call should implicitly disable the device once the
probe is over if there is no explicit reference gained. There is no
need to call pm_runtime_suspend() before the pm_runtime_disable()
call.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use devm_request_threaded_irq() for the host interrupt handlers so we
do not have to worry about freeing them on exit or error. Tidies up the
exit path code for the driver.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the devm_clk_get() code to get the clock and allow it to be freed
automatically on release.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Start tidying the probe/release code by using devm_ioremap_resource() to
map the IO registers.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the initial print to show chip version and the bus rate it is
working at instead of the driver version. This is more useful information
as we already know which driver version from the kernel it is in.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Casting an integer to a void * generates a "cast to pointer from integer
of different size" warning. Cast the integer to an unsigned long first
to fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The channel request and configuration code is duplicated for the rx and
tx channels. Create a function that requests a single channel and call
it twice instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously only clk_enable|disable were being used. Adapt properly
to the clock API, by also using clk_prepare|unprepare.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some newer MMCIF IP revisions contain a CE_CLK_CTRL2 register, that has to
be set for proper operation. Support for this feature is added in a way to
preserve the current behaviour by default, i.e. when it is not enabled
in platform data. Patch is based on work by Nobuyuki HIRAI.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some earlier MMCIF IP revisions contained Command Completion Signal
support, which has been dropped again in modern versions. Sopport for
this feature is added in a way to preserve the current behaviour by
default, i.e. when it is not enabled in platform data. Patch is based
on work by Nobuyuki HIRAI.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
To use DMA in the Device Tree case the driver has to be modified
to use suitable API to obtain DMA channels.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sh_dma.h isn't needed in sh_mmcif.h, move it into sh_mmcif.c.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a debounce parameter to the mmc_gpio_request_cd() function that
enables GPIO debouncing when set to a non-zero value. This can be used
by MMC host drivers to enable debouncing on the card detect signal.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
