Northstar devices have MDIO bus that may contain various PHYs attached.
A common example is USB 3.0 PHY (that doesn't have an MDIO driver yet).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This uses CPU thermal sensor available on every Northstar chipset to
monitor temperature. We don't have any cooling or throttling so only a
critical trip was added.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
So far every Northstar device we have seen was using the same serial
console params (115200n8). It probably make the most sense to put it in
some proper dtsi files instead of repeating over and over for every
single device. As different boards may use different bootloaders it
seems the safest idea is to use board specific dtsi files.
Just in case some vendor decides to use different UART (parameters) this
can be always easily overwritten.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add I2C support to the bcm5301x Device Tree. Since no driver changes
are needed to enable this hardware, only the device tree changes are
required to make this functional.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for the ARM TWD Watchdog to the bcm5301x device tree. The
ARM TWD timer allocated the register space for the WDT, so this patch
necessitated shrinking that. Also, the GIC masks were added for these.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
GIC_PPI flags were misconfigured for the timers, resulting in errors
like:
[ 0.000000] GIC: PPI11 is secure or misconfigured
Changing them to being edge triggered corrects the issue
Suggested-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Fixes: d27509f1 ("ARM: BCM5301X: add dts files for BCM4708 SoC")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The iproc-qspi driver is the SPI driver that should be used going
forward. Modify the SPI DT entry to use this driver, and add an entry
in the bcm953012k DTS file to enable the SPI.
Tested on the bcm953012k board.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Netgear R8000 is a tri-band home router. It has three BCM43602 chipsets
two of them for 5 GHz band. Both seem the same and their firmwares
report the same set of channels. The problem is due to hardware / board
design there are extra limitations that should be respected.
First PHY should be used for U-NII-2 and U-NII-3. Third PHY should be
used for U-NII-1. Using them in a different way may result in wireless
not working or in noticeably reduced performance. Basic version of this
info was provided by Broadcom employee, then it has been verified by me
using original vendor firmware (which has limitations hardcoded in UI).
This patch uses recently introduced ieee80211-freq-limit property to
describe these limitations at DT level.
Referencing PCIe devices in DT required specifying all related bridges.
Below you can see (a bit complex) PCI tree from R8000 that explains all
entries that I needed to put in DT.
0000:00:00.0 14e4:8012 Bridge Device
└─ 0000:01:00.0 14e4:aa52 Network Controller
0001:00:00.0 14e4:8012 Bridge Device
└─ 0001:01:00.0 10b5:8603 Bridge Device
├─ 0001:02:01.0 10b5:8603 Bridge Device
│ └─ 0001:03:00.0 14e4:aa52 Network Controller
├─ 0001:02:02.0 10b5:8603 Bridge Device
│ └─ 0001:04:00.0 14e4:aa52 Network Controller
├─ 0001:02:03.0 000d:0000 0x000000
├─ 0001:02:04.0 000d:0000 0x000000
├─ 0001:02:05.0 000d:0000 0x000000
├─ 0001:02:06.0 000d:0000 0x000000
├─ (...)
├─ 0001:02:1d.0 000d:0000 0x000000
├─ 0001:02:1e.0 000d:0000 0x000000
└─ 0001:02:1f.0 000d:0000 0x000000
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There are 3 separated controllers, one per USB /standard/. With PHY
drivers in place they can be simply supported with generic drivers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Driver for Northstar USB 3.0 PHY has been recently added under the name
phy-bcm-ns-usb3. Add binding for it into the DT files.
The only slightly tricky part is BCM47094 which uses different PHY
version and requires different compatible value.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Driver for Northstar USB 2.0 PHY was added in 4.7-rc1 by:
commit d3feb40673 ("phy: bcm-ns-usb2: new driver for USB 2.0 PHY on
Northstar").
It should be used to let EHCI platform driver init PHY.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the DT node for the random number generator peripheral.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add interrupt mapping for the Switch Register Access Block. Only 12
interrupts are usable at the moment even though up to 32 are dedicated
to the SRAB.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the Switch Register Access Block which is a special piece of
hardware allowing us to perform indirect read/writes towards the
integrated BCM5301X Ethernet switch.
We also add the 4 Gigabit MAC Device Tree nodes within the brcm,bus-axi
bus node to get proper binding between the BCMA instantiated core and
the Device Tree nodes. We will need that to be able to reference
Ethernet Device Tree nodes in a future patch adding the switch ports
layout.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Controller is present on every BCM4708* board but only few devices have
serial flash attached so mark it as disabled by default.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
There are few devices that have USB power controlled using GPIO. Linux
USB host driver (bcma-hcd) already supports this by reading vcc-gpio
from DT. Set it properly for all known devices.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Replace current device tree dummy clocks with real clock support for
Broadcom Northstar SoCs.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
In the default Broadcom SDK the shared override is activated for this
cache controller, do the same in the upstream code. Data and
instruction prefetching is not activated by default for this cache
controller on the bcm53xx SoC, do it manually like it is done in the
vendor SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The driver for the PCIe controller was just added, this adds the
missing definition of the IRQ numbers to device tree. The driver itself
will be automatically detected by bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the NAND flash chip description for a standard chip found
connected to this SoC. This makes use of generic Broadcom NAND driver
with the iProc interface.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
IRQ support for Broadcom's bus-axi driver bcma was merged into John
Linville's wireless tree and will show up in 3.19. This patch makes use
of this feature in the DTS file for the the BCM5301X SoCs. I left the
PCIe controller out, because this still needs some discussion.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This has been successfully tested on Netgear R6250 and two other
development (unnamed) devices, all of them BCM4708 based.
We also got a possitive feedback from R7000 (BCM4709) tester.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
