This transfers the muxing and biasing of the ethernet-related
pins on the snowball over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the few remaining HREFv60 pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Put two extra configs into the device tree to handle the default
configuration of the display reset signals on the HREFv60plus,
move this over from the board file to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the control of muxing and enabling the IPGPIO (image
processor GPIO) from the static set-up to the device tree.
Use a hog as we have no device for the flash controller yet.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves some of the pin setup related to the CW1200 WLAN
module over to the device tree. As the driver is not yet
activated for the CW1200 WLAN we do not assign this pinctrl
state to any device node yet.
Get rid of the cmdline argument passing of a certain U9500
platform variant, as this is not supported by the kernel or
any device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves over the configuration of the GPIO keys (used for
proximity sensor and Hall effect sensor) from the static pin
configuration file to the device tree. As part of the exercise,
implement the GPIO keys properly in a per-UIB file as this
setup actually differs with each UIB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old HREFs (MOP500) were controlling an image-processor
GPIO (IPGPIO) by using hogs. Do the same thing with device tree
and get rid of the mop500_pins setting.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin mappings for the STM (System Trace Macrocell) are not
really used by anything: we have no driver for is and the settings
are not connected to any device. We can recreate the different
mux outputs in the device tree the day we need them. Drop these
for now.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the SKE keypad pin control table out of the board
file and into the device tree. This was previously set to be
active on all MOP500 and HREF boards but after reading the
schematic this seems incorrect: the HREFv60 and later uses
one of these for MC5 and no reference designs have the SKE
connected to any hardware so just leave the pins alone
in the power-on state.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the MCDE pin control table out of the board file
and into the device tree. Some pins and configs have been
marked as used by sub-devices or slaves to the MCDE, such
as I2C device 0-070 which is the HDMI interface circuit
AV8100, but the pins rather belong to the MCDE SOC block
as they come out of the main ASIC. The touch screen GPIO
is not related to MCDE so this gets deleted and need to
be tied to the respective touch screen (I2C) device
once that device is added instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the SPI pin control table out of the board file
and into the device tree. Move the specific setting for
SSP0 on the HREFprev60 into the prev60-specific DTS file.
The SPI2 configuration is not really connected to any device,
as it will conflict with GPIO218 which is used on all HREFs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the MUSB pin control table out of the board file
and into the device tree. Tie the config to the on-chip MUSB
device rather than the ab8500-usb device which is off-chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the input-pulled-up setting for GPIO217 as used
on the HREFs prior to v60 from the boardfile to the device
tree. GPIO218 is only used with the TVK UIB so move it to
that .dtsi file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add nodes for MSP0 and MSP2 on the HREF and Snowball
so we can reference the pins properly.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Define possible states also for I2C4 even if it's not
used by any board file at this time.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree.
We create a new .dtsi-file to be shared between all the
MOP500-related boards, that include all HREF variants and
the Snowball board. Assign pin states for HREF and Snowball
boards alike.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin definition file dates back to a time before the pin
control subsystem. The functions called inside that pin control
driver are now deleted. Let's get rid of this file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Removes the following warnings:
arch/arm/mach-ux500/board-mop500-pins.c:51:6: warning: 'slpm_in_nopull_wkup' defined but not used [-Wunused-variable]
arch/arm/mach-ux500/board-mop500-pins.c:63:6: warning: 'slpm_out_lo_wkup' defined but not used [-Wunused-variable]
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Linus Walleij <linux.walleij@linaro.org>
This adds pin control tables for the ABx500 (AB8500 and
AB8505) PMIC, which also happens to act as a multimedia
pin expander on the ux500 platforms.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update MSP1 pinctrl definitions in mop500_family_pinmap by removing
sleep state and setting default ones as pin hogs, as those are used by
both ux500-msp-i2s.1 and ux500-msp-i2s.3.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem
specific interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into
platform specific interface, or to get called from platform specific
code, as long as all information about the hardware is provided
through a device tree.
Most of the drivers we touch this time are for clocksource. Since
now most of them are part of drivers/clocksource, I expect that we
won't have to touch these again from arm-soc and can let the
clocksource maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the
merge conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface
for taking devices on the SoC out of reset or back into reset.
Patches to use this interface on i.MX follow later in this merge
window, and we are going to have other platforms (at least tegra
and sirf) get converted in 3.11. This will let us get rid of
platform specific callbacks in a number of platform independent
device drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZWk9
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
This removes <mach/hardware.h> and <mach/db8500-regs.h>
from the Ux500, merging them into the local include
"db8500-regs.h" in mach-ux500. There is some impact
outside the ux500 machine, but most of it is dealt with
in earlier patches.
Contains portions of a clean-up patch from Arnd Bergmann.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DB8500_PIN_SLEEP was defined twice, drop one of the two.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here we setup the GPIO pin responsible for illuminating the user
LED on the Snowball low-cost development board.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The wrong macro was used so we didn't really create an
idle state for these pins.
Signed-off-by: Julien Delacou <julien.delacou@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Recent pin changes produce this warning:
arch/arm/mach-ux500/board-mop500-pins.c:73:22:
error: 'out_hi_wkup_pdis' defined but not used
[-Werror=unused-variable]
Fix this by deleting the offending definition.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
GPIO31 and GPIO32 (CTS/RTS) are handled by the magnetometer and
shall not simultaneously be controlled by UART2.
Reported-by: Peter Nessrup <peter.nessrup@stericsson.com>
Signed-off-by: Jorgen Jonsson <jorgen.jonsson@stericsson.com>
Reviewed-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This merges the old <plat/pincfg.h> header into
<linux/platform_data/pinctrl-nomadik.h> and rids us of
yet one more <plat/*> include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the platform data header for the Nomadik pin controller
to <linux/platform_data/pinctrl-nomadik.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add the new stm pinctrl states
definitions for the Ux500 MOP500 series.
Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Changed a comment and ordered BIAS defines around a bit.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This defines the sleep states for the SDI (MMC/SD) interfaces
on the MOP500 reference designs.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old pinctrl table for the SKE keypad was using all the
wrong settings and positions. Fixing it up to one that works!
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>nn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some merge mishap has caused the DB8500_PIN_SLEEP() macro to
appear twice. Get rid of the suplus copy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds an idle state to the SPI pin control entry.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes up the pins used by the VSI interface to the HDMI
AV8100 encoder.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This defines the proper sleep states for all the I2C pins of
the MOP500 DB8500 ASIC setting.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This named the sleep mode pin configurations as *slpm* rather
than *sleep* to correspond better with the settings from the
datasheet. It also defines an optional sleep mode for the SPI
controller SPI2.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO216_AG12 is configured as a gpio for SPI2, so select
the spi2_oc1_2 pin group instead of spi2_oc1_1
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Due to specific constraint, pin HSIT_ACWAKE0_a is
not driven by HSI block but as a GPIO.
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MSP platform data callbacks use the old custom callbacks to
set the state of the pins, switch over to using pinctrl.
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
UART0 had a hack that enabled its pins on init and put it to
sleep on the exit callback. Replace this with the pinctrl calls
to do the same thing and update the runtime table with the two
apropriate states for runtime/active and idle.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At the beginning of the first patch series I included the custom
ux500 pin control system to make sure I could eventually replace
it with the standard subsystem driver. So now that we've done so,
let's remove it.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Ux500 family to use the pinctrl driver for
configuring pins.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This updates the Ux500 pin handling to take much more care when
applying pin settings for different platforms and peripherals.
This is an accumulation of a longer history of updates to the
MOP500 family pin file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement an API to allow a list of pincfgs to be remuxed to active
and sleep modes, for power saving. This is not exported on purpose,
because it is not to be called by drivers directly.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
