When allocating space for 32-bit BARs, we previously limited RESOURCE
addresses so they would fit in 32 bits. However, the BUS address need not
be the same as the resource address, and it's the bus address that must fit
in the 32-bit BAR.
This patch adds:
- pci_clip_resource_to_region(), which clips a resource so it contains
only the range that maps to the specified bus address region, e.g., to
clip a resource to 32-bit bus addresses, and
- pci_bus_alloc_from_region(), which allocates space for a resource from
the specified bus address region,
and changes pci_bus_alloc_resource() to allocate space for 64-bit BARs from
the entire bus address region, and space for 32-bit BARs from only the bus
address region below 4GB.
If we had this window:
pci_root HWP0002:0a: host bridge window [mem 0xf0180000000-0xf01fedfffff] (bus address [0x80000000-0xfedfffff])
we previously could not put a 32-bit BAR there, because the CPU addresses
don't fit in 32 bits. This patch fixes this, so we can use this space for
32-bit BARs.
It's also possible (though unlikely) to have resources with 32-bit CPU
addresses but bus addresses above 4GB. In this case the previous code
would allocate space that a 32-bit BAR could not map.
Remove PCIBIOS_MAX_MEM_32, which is no longer used.
[bhelgaas: reworked starting from http://lkml.kernel.org/r/1386658484-15774-3-git-send-email-yinghai@kernel.org]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This adds pci_enable_msi_range(), which supersedes the pci_enable_msi()
and pci_enable_msi_block() MSI interfaces.
It also adds pci_enable_msix_range(), which supersedes the
pci_enable_msix() MSI-X interface.
The old interfaces have three categories of return values:
negative: failure; caller should not retry
positive: failure; value indicates number of interrupts that *could*
have been allocated, and caller may retry with a smaller request
zero: success; at least as many interrupts allocated as requested
It is error-prone to handle these three cases correctly in drivers.
The new functions return either a negative error code or a number of
successfully allocated MSI/MSI-X interrupts, which is expected to lead to
clearer device driver code.
pci_enable_msi(), pci_enable_msi_block() and pci_enable_msix() still exist
unchanged, but are deprecated and may be removed after callers are updated.
[bhelgaas: tweak changelog]
Suggested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
This creates an MSI-X counterpart for pci_msi_vec_count(). Device drivers
can use this function to obtain maximum number of MSI-X interrupts the
device supports and use that number in a subsequent call to
pci_enable_msix().
pci_msix_vec_count() supersedes pci_msix_table_size() and returns a
negative errno if device does not support MSI-X interrupts. After this
update, callers must always check the returned value.
The only user of pci_msix_table_size() was the PCI-Express port driver,
which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
The new pci_msi_vec_count() interface makes pci_enable_msi_block_auto()
superfluous.
Drivers can use pci_msi_vec_count() to learn the maximum number of MSIs
supported by the device, and then call pci_enable_msi_block().
pci_enable_msi_block_auto() was introduced recently, and its only user is
the AHCI driver, which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Device drivers can use this interface to obtain the maximum number of MSI
interrupts the device supports and use that number, e.g., in a subsequent
call to pci_enable_msi_block().
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
We store BAR information as a struct resource, which contains the CPU
address, not the bus address. Drivers often need the bus address, and
there's currently no convenient way to get it, so they often read the
BAR directly, or use the resource address (which doesn't work if there's
any translation between CPU and bus addresses).
Add pci_bus_address() to make this convenient.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/msi:
PCI/MSI: Make pci_enable_msi/msix() 'nvec' argument type as int
PCI/MSI: Return -ENOSYS for unimplemented interfaces, not -1
PCI/MSI: Return msix_capability_init() failure if populate_msi_sysfs() fails
s390/PCI: Remove superfluous check of MSI type
s390/PCI: Fix single MSI only check
PCI/MSI: Export MSI mode using attributes, not kobjects
Make pci_enable_msi_block(), pci_enable_msi_block_auto() and
pci_enable_msix() consistent with regard to the type of 'nvec' argument.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
The PCI MSI sysfs code is a mess with kobjects for things that don't really
need to be kobjects. This patch creates attributes dynamically for the MSI
interrupts instead of using kobjects.
Note, this removes a directory from sysfs. Old MSI kobjects:
pci_device
└── msi_irqs
└── 40
└── mode
New MSI attributes:
pci_device
└── msi_irqs
└── 40
As there was only one file "mode" with the kobject model, the interrupt
number is now a file that returns the "mode" of the interrupt (msi vs.
msix).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
* pci/vc:
PCI: Rename PCI_VC_PORT_REG1/2 to PCI_VC_PORT_CAP1/2
PCI: Add Virtual Channel to save/restore support
PCI: Add support for save/restore of extended capabilities
PCI: Add pci_wait_for_pending() (refactor pci_wait_for_pending_transaction())
While we don't really have any infrastructure for making use of VC
support, the system BIOS can configure the topology to non-default
VC values prior to boot. This may be due to silicon bugs, desire to
reserve traffic classes, or perhaps just BIOS bugs. When we reset
devices, the VC configuration may return to default values, which can
be incompatible with devices upstream. For instance, Nvidia GRID
cards provide a PCIe switch and some number of GPUs, all supporting
VC. The power-on default for VC is to support TC0-7 across VC0,
however some platforms will only enable TC0/VC0 mapping across the
topology. When we do a secondary bus reset on the downstream switch
port, the GPU is reset to a TC0-7/VC0 mapping while the opposite end
of the link only enables TC0/VC0. If the GPU attempts to use TC1-7,
it fails.
This patch attempts to provide complete support for VC save/restore,
even beyond the minimally required use case above. This includes
save/restore and reload of the arbitration table, save/restore and
reload of the port arbitration tables, and re-enabling of the
channels for VC, VC9, and MFVC capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Current save/restore is specific to standard capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We currently have two instance of this loop which waits for a pending bit
to clear in a status dword. Generalize the function for future users.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Prefer use of the direct definition of struct pci_device_id instead of
indirection via macro DEFINE_PCI_DEVICE_TABLE.
Update the PCI documentation to deprecate DEFINE_PCI_DEVICE_TABLE. Update
checkpatch adding --fix option.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Modify tg3_chip_reset() and tg3_close() to check if the PCI network
adapter device is accessible at all in order to skip poking it or
trying to handle a carrier loss in vain when that's not the case.
Introduce a special PCI helper function pci_device_is_present()
for this purpose.
Of course, this uncovers the lack of the appropriate RTNL locking
in tg3_suspend() and tg3_resume(), so add that locking in there
too.
These changes prevent tg3 from burning a CPU at 100% load level for
solid several seconds after the Thunderbolt link is disconnected from
a Matrox DS1 docking station.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pasting the verbatim PCI_(VENDOR|DEVICE)_* macros in the __pci_fixup_*
symbol names results in insanely long names such as
__pci_fixup_resumePCI_VENDOR_ID_SERVERWORKSPCI_DEVICE_ID_SERVERWORKS_HT1000SBquirk_disable_broadcom_boot_interrupt
When Link-Time Optimization adds its numeric suffix to such symbol, it
overflows the namebuf[KSYM_NAME_LEN] array in kernel/kallsyms.c. Use the
line number instead to create (nearly) unique symbol names.
Reported-by: Joe Mario <jmario@redhat.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Andi Kleen <ak@linux.intel.com>
Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This adds a pci_upstream_bridge() interface to find the PCI-to-PCI bridge
upstream from a device. This is typically just "dev->bus->self", but in
the case of a VF on a virtual bus, we have to start from the corresponding
PF. Returns NULL if there is no upstream PCI bridge, i.e., if the device
is on a root bus.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Some code assumes "bus->self == NULL" means the bus is a root bus. This
adds a comment explaining why this is incorrect ("virtual" buses added for
SR-IOV have "bus->self == NULL" but are not root buses).
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
No one uses "is_pcie" now; remove this obsolete member.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use normal kernel-doc "Returns:" instead of "retrun"
Assignment to bool is always 1 or 0 so the !! isn't necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
* pci/misc:
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
* pci/yinghai-assign-unassigned-v6:
PCI: Assign resources for hot-added host bridge more aggressively
PCI: Move resource reallocation code to non-__init
PCI: Delay enabling bridges until they're needed
PCI: Assign resources on a per-bus basis
PCI: Enable unassigned resource reallocation on per-bus basis
PCI: Turn on reallocation for unassigned resources with host bridge offset
PCI: Look for unassigned resources on per-bus basis
PCI: Drop temporary variable in pci_assign_unassigned_resources()
Platforms may want to provide architecture-specific functionality when
a PCI device is doing a hibernate transition. Add a weak symbol
pcibios_pm_ops that architectures can override to do so.
[bhelgaas: fold in return value checks from v2 patch]
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Based on a patch by Jon Mason (see URL below).
All users of pcie_bus_configure_settings() pass arguments of the form
"bus, bus->self->pcie_mpss". The "mpss" argument is redundant since we
can easily look it up internally. In addition, all callers check
"bus->self" for NULL, which we can also do internally.
This patch simplifies the interface and the callers. No functional change.
Reference: http://lkml.kernel.org/r/1317048850-30728-2-git-send-email-mason@myri.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Users of pci_reset_bus() and pci_reset_slot() need a way to probe
whether the bus or slot supports reset. Add trivial helper functions
and export them as vfio-pci will make use of these.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Sometimes pci_reset_function() is not sufficient. We have cases where
devices do not support any kind of reset, but there might be multiple
functions on the bus preventing pci_reset_function() from doing a
secondary bus reset. We also have cases where a device will advertise
that it supports a PM reset, but really does nothing on D3hot->D0
(graphics cards are notorious for this). These devices often also
have more than one function, so even blacklisting PM reset for them
wouldn't allow a secondary bus reset through pci_reset_function().
If a driver supports multiple devices it should have the ability to
induce a bus reset when it needs to. This patch provides that ability
through pci_reset_slot() and pci_reset_bus(). It's the caller's
responsibility when using these interfaces to understand that all of
the devices in or below the slot (or on or below the bus) will be
reset and therefore should be under control of the caller. PCI state
of all the affected devices is saved and restored around these resets,
but internal state of all of the affected devices is reset (which
should be the intention).
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
New routine to avoid duplication of code to wait for pending PCI
transactions to complete.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The new struct msi_chip is used to associated an MSI controller with a
PCI bus. It is automatically handed down from the root to its children
during bus enumeration.
This patch provides default (weak) implementations for the architecture-
specific MSI functions (arch_setup_msi_irq(), arch_teardown_msi_irq()
and arch_msi_check_device()) which check if a PCI device's bus has an
attached MSI chip and forward the call appropriately.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Daniel Price <daniel.price@gmail.com>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Move the secondary bus reset code from pci_parent_bus_reset() into its own
function. Export it as we'll later be calling it from hotplug controllers
and elsewhere.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A PCI Express device can potentially report a link width and speed which it will
not properly fulfill due to being plugged into a slower link higher in the
chain. This function walks up the PCI bus chain and calculates the minimum link
width and speed of this entire chain. This can be useful to enable a device to
determine if it has enough bandwidth for optimum functionality.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
pcie_link_width is the enum used to define the link width values for a pcie
device. This enum should not be contained solely in pci_hotplug.h, and this
patch moves it next to pci_bus_speed in pci.h
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When hot-adding an ACPI host bridge, use
pci_assign_unassigned_root_bus_resources() instead of
pci_assign_unassigned_bus_resources().
The former is more aggressive and will release and reassign existing
resources if necessary. This is safe at hot-add time because no drivers
are bound to devices below the new host bridge yet.
[bhelgaas: changelog, split __init changes out for reviewability]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We currently enable PCI bridges after scanning a bus and assigning
resources. This is often done in arch code.
This patch changes this so we don't enable a bridge until necessary, i.e.,
until we enable a PCI device behind the bridge. We do this in the generic
pci_enable_device() path, so this also removes the arch-specific code to
enable bridges.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Platforms may want to provide architecture-specific functionality when
a PCI device is released. Add a pcibios_release_device() call that
architectures can override to do so.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Here we introduce a new interface to replace alloc_pci_dev():
struct pci_dev *pci_alloc_dev(struct pci_bus *bus)
It takes a "struct pci_bus *" argument, so we can alloc a PCI device
on a target PCI bus, and it acquires a reference on the pci_bus.
We use pci_alloc_dev(NULL) to simplify the old alloc_pci_dev(),
and keep it for a while but mark it as __deprecated.
Holding a reference to the pci_bus ensures that referencing
pci_dev->bus is valid as long as the pci_dev is valid.
[bhelgaas: keep existing "return error early" structure in pci_alloc_dev()]
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
This function is meant to add a helper function that will determine if a PF
has any VFs that are currently assigned to a guest. We currently have been
implementing this function per driver, and going forward I would like to avoid
that by making this function generic and using this helper.
v2: Removed extern from declaration of pci_vfs_assigned in pci.h and return
0 if SR-IOV is disabled with is inline with other PCI SRIOV functions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* pci/gavin-msi-cleanup:
vfio-pci: Use cached MSI/MSI-X capabilities
vfio-pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
PCI: Remove "extern" from function declarations
PCI: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
PCI: Drop msi_mask_reg() and remove drivers/pci/msi.h
PCI: Use msix_table_size() directly, drop multi_msix_capable()
PCI: Drop msix_table_offset_reg() and msix_pba_offset_reg() macros
PCI: Drop is_64bit_address() and is_mask_bit_support() macros
PCI: Drop msi_data_reg() macro
PCI: Drop msi_lower_address_reg() and msi_upper_address_reg() macros
PCI: Drop msi_control_reg() macro and use PCI_MSI_FLAGS directly
PCI: Use cached MSI/MSI-X offsets from dev, not from msi_desc
PCI: Clean up MSI/MSI-X capability #defines
PCI: Use cached MSI-X cap while enabling MSI-X
PCI: Use cached MSI cap while enabling MSI interrupts
PCI: Remove MSI/MSI-X cap check in pci_msi_check_device()
PCI: Cache MSI/MSI-X capability offsets in struct pci_dev
PCI: Use u8, not int, for PM capability offset
[SCSI] megaraid_sas: Use correct #define for MSI-X capability
The patch caches the MSI and MSI-X capability offset in PCI device
(struct pci_dev) so that we needn't read it from the config space
upon enabling or disabling MSI or MSI-X interrupts.
[bhelgaas: moved pm_cap size change to separate patch]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Power Management Capability (PCI_CAP_ID_PM == 0x01) is defined by PCI
and must appear in the 256-byte PCI Configuration Space from 0-0xff. It
cannot be in the PCIe Extended Configuration space from 0x100-0xfff, so
we only need a u8 to hold its offset.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pci/cleanup:
PCI: Remove "extern" from function declarations
PCI: Warn about failures instead of "must_check" functions
PCI: Remove __must_check from definitions
PCI: Remove unused variables
PCI: Move cpci_hotplug_init() proto to header file
PCI: Make local functions/structs static
PCI: Fix missing prototype for pcie_port_acpi_setup()
Conflicts:
drivers/pci/hotplug/acpiphp.h
include/linux/pci.h
We had an inconsistent mix of using and omitting the "extern" keyword
on function declarations in header files. This removes them all.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/jiang-subdrivers:
PCI/ACPI: Remove support of ACPI PCI subdrivers
PCI: acpiphp: Protect acpiphp data structures from concurrent updates
PCI: acpiphp: Use normal list to simplify implementation
PCI: acpiphp: Do not use ACPI PCI subdriver mechanism
PCI: acpiphp: Convert acpiphp to be builtin only, not modular
PCI/ACPI: Handle PCI slot devices when creating/destroying PCI buses
x86/PCI: Implement pcibios_{add|remove}_bus() hooks
ia64/PCI: Implement pcibios_{add|remove}_bus() hooks
PCI/ACPI: Prepare stub functions to handle ACPI PCI (hotplug) slots
PCI: Add pcibios hooks for adding and removing PCI buses
PCI: acpiphp: Replace local macros with standard ACPI macros
PCI: acpiphp: Remove all functions even if function 0 doesn't exist
PCI: acpiphp: Use list_for_each_entry_safe() in acpiphp_sanitize_bus()
PCI: Clean up usages of pci_bus->is_added
PCI: When removing bus, always remove legacy files & unregister
On ACPI-based platforms, the pci_slot driver creates PCI slot devices
according to information from ACPI tables by registering an ACPI PCI
subdriver. The ACPI PCI subdriver will only be called when creating/
destroying PCI root buses, and it won't be called when hot-plugging
P2P bridges. It may cause stale PCI slot devices after hot-removing
a P2P bridge if that bridge has associated PCI slots. And the acpiphp
driver has the same issue too.
This patch introduces two hook points into the PCI core, which will
be invoked when creating/destroying PCI buses for PCI host and P2P
bridges. They could be used to setup/destroy platform dependent stuff
in a unified way, both at boot time and for PCI hotplug operations.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Myron Stowe <myron.stowe@redhat.com>
The __weak annotation on the pcibios_get_phb_of_node() declaration
causes *every* definition to be marked "weak." The linker then
selects one based on link order, which may be the wrong one.
Gabor found that on MIPS, the linker selected the generic implementation
from drivers/pci even though arch/mips supplied a definition without the
__weak annotation:
$ mipsel-openwrt-linux-readelf -s arch/mips/pci/built-in.o \
drivers/pci/built-in.o vmlinux.o | grep pcibios_get_phb_of_node
86: 0000046c 12 FUNC WEAK DEFAULT 2 pcibios_get_phb_of_node
1430: 00012e2c 104 FUNC WEAK DEFAULT 2 pcibios_get_phb_of_node
31898: 0017e4ec 104 FUNC WEAK DEFAULT 2 pcibios_get_phb_of_node
This removes the __weak annotation from the pcibios_get_phb_of_node()
declaration so arch-specific non-weak implementations work reliably.
Suggested-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It turns out that some UEFI systems provide apparently an apparently valid
PCI ROM BAR that turns out to contain garbage, so the attempt in 547b52463
to prefer the ROM from the BAR actually breaks a different set of machines.
As Linus pointed out, the graphics drivers are probably in the best
position to make this judgement, so this basically reverts 547b52463 and
f9a37be0f and adds a new helper function. Followup patches will add support
to nouveau and radeon for probing this ROM source if they can't find a ROM
from some other source.
[bhelgaas: added reporter and bugzilla pointers, s/f4eb5ff05/547b52463]
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=927451
Reference: http://lkml.kernel.org/r/kg69ef$vdb$1@ger.gmane.org
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Reported-by: Chris Murphy <bugzilla@colorremedies.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI defines PCI_DEVFN(), PCI_SLOT(), and PCI_FUNC() interfaces; however,
it doesn't have interfaces to return PCI bus and PCI device id. Drivers
(AMD IOMMU, and AER) implement module specific definitions for PCI_BUS()
and AMD_IOMMU driver also has a module specific interface to calculate PCI
device id from bus number and devfn.
Add PCI_BUS_NUM and PCI_DEVID interfaces to return PCI bus number and PCI
device id respectively to avoid the need for duplicate definitions in other
modules. AER driver code and AMD IOMMU driver define PCI_BUS. AMD IOMMU
driver defines an interface to calculate device id from bus number, and
devfn pair.
PCI_DEVFN(), PCI_SLOT(), and PCI_FUNC() interfaces are exported to
user-space via uapi/linux/pci.h. However, in the interest to keep the new
interfaces as kernel only and not export them to user-space unnecessarily,
added them to linux/pci.h instead.
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRKS3hAAoJEFmIoMA60/r8xxoP/j1CS4oCZAnBIVT9fKBkis+/
CENcfHIUKj6J9iMfJEVvqBELvqaLqtpeNwAGMcGPxV7VuT3K1QumChfaTpRDP0HC
VDRmrjcmfenEK+YPOG7acsrTyqk2wjpLOyu9MKRxtC5u7tF6376KQpkEFpO4haL4
eUHTxfE76OkrPBSvx3+PUSf6jqrvrNbjX8K6HdDVVlm3sVAQKmYJU/Wphv2NPOqa
CAMyCzEGybFjr8hDRwvWgr+06c718GMwQUbnrPdHXAe7lMNMrN/XVBmU9ABN3Aas
icd3lrDs+yPObgcO/gT8+sAZErCtdJ9zuHGYHdYpRbIQj/5JT4TMk7tw/Bj7vKY9
Mqmho9GR5YmYTRN9f1r+2n5AQ/KYWXJDrRNOnt5/ys5BOM3vwJ7WJ902zpSwtFQp
nLX+oD/hLfzpnoIQGDuBAoAXp2Kam3XWRgVvG78buRNrPj+kUzimk14a8qQeY+CB
El6UKuwi5Uv/qgs1gAqqjmZmsAkon2DnsRZa6Fl8NTkDlis7LY4gp9OU38ySFpB+
PhCmRyCZmDDqTVtwj6XzR3nPQ5LBSbvsTfgMxYMIUSXHa06tyb2q5p4mEIas0OmU
RKaP5xQqZuTgD8fbdYrx0xgSrn7JHt/j/X//Qs6unlLCWhlpm3LjJZKxyw2FwBGr
o4Lci+PiBh3MowCrju9D
=ER3b
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug
- Major overhaul of ACPI host bridge add/start (Rafael Wysocki, Yinghai Lu)
- Major overhaul of PCI/ACPI binding (Rafael Wysocki, Yinghai Lu)
- Split out ACPI host bridge and ACPI PCI device hotplug (Yinghai Lu)
- Stop caching _PRT and make independent of bus numbers (Yinghai Lu)
PCI device hotplug
- Clean up cpqphp dead code (Sasha Levin)
- Disable ARI unless device and upstream bridge support it (Yijing Wang)
- Initialize all hot-added devices (not functions 0-7) (Yijing Wang)
Power management
- Don't touch ASPM if disabled (Joe Lawrence)
- Fix ASPM link state management (Myron Stowe)
Miscellaneous
- Fix PCI_EXP_FLAGS accessor (Alex Williamson)
- Disable Bus Master in pci_device_shutdown (Konstantin Khlebnikov)
- Document hotplug resource and MPS parameters (Yijing Wang)
- Add accessor for PCIe capabilities (Myron Stowe)
- Drop pciehp suspend/resume messages (Paul Bolle)
- Make pci_slot built-in only (not a module) (Jiang Liu)
- Remove unused PCI/ACPI bind ops (Jiang Liu)
- Removed used pci_root_bus (Bjorn Helgaas)"
* tag 'pci-v3.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
PCI/ACPI: Don't cache _PRT, and don't associate them with bus numbers
PCI: Fix PCI Express Capability accessors for PCI_EXP_FLAGS
ACPI / PCI: Make pci_slot built-in only, not a module
PCI/PM: Clear state_saved during suspend
PCI: Use atomic_inc_return() rather than atomic_add_return()
PCI: Catch attempts to disable already-disabled devices
PCI: Disable Bus Master unconditionally in pci_device_shutdown()
PCI: acpiphp: Remove dead code for PCI host bridge hotplug
PCI: acpiphp: Create companion ACPI devices before creating PCI devices
PCI: Remove unused "rc" in virtfn_add_bus()
PCI: pciehp: Drop suspend/resume ENTRY messages
PCI/ASPM: Don't touch ASPM if forcibly disabled
PCI/ASPM: Deallocate upstream link state even if device is not PCIe
PCI: Document MPS parameters pci=pcie_bus_safe, pci=pcie_bus_perf, etc
PCI: Document hpiosize= and hpmemsize= resource reservation parameters
PCI: Use PCI Express Capability accessor
PCI: Introduce accessor to retrieve PCIe Capabilities Register
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
...
Provide an accessor to retrieve the PCI Express device's Capabilities
Register.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/yinghai-root-bus-hotplug:
PCI: Put pci_dev in device tree as early as possible
PCI: Skip attaching driver in device_add()
PCI: acpiphp: Keep driver loaded even if no slots found
PCI/ACPI: Print info if host bridge notify handler installation fails
PCI: acpiphp: Move host bridge hotplug to pci_root.c
PCI/ACPI: acpiphp: Rename alloc_acpiphp_hp_work() to alloc_acpi_hp_work()
PCI: Make device create/destroy logic symmetric
PCI: Fix reference count leak in pci_dev_present()
PCI: Set pci_dev dev_node early so IOAPIC irq_descs are allocated locally
PCI: Add root bus children dev's res to fail list
PCI: acpiphp: Add is_hotplug_bridge detection
Conflicts:
drivers/pci/pci.h
We want to add PCI devices to the device tree as early as possible but
delay attaching drivers.
device_add() adds a device to the device hierarchy and (via
device_attach()) attaches a matching driver and calls its .probe() method.
We want to separate adding the device to the hierarchy from attaching the
driver.
This patch does that by adding "match_driver" in struct pci_dev. When
false, we return failure from pci_bus_match(), which makes device_attach()
believe there's no matching driver.
Later, we set "match_driver = true" and call device_attach() again, which
now attaches the driver and calls its .probe() method.
[bhelgaas: changelog, explicitly init dev->match_driver,
fold device_attach() call into pci_bus_add_device()]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The new function pci_enable_msi_block_auto() tries to allocate
maximum possible number of MSIs up to the number the device
supports. It generalizes a pattern when pci_enable_msi_block()
is contiguously called until it succeeds or fails.
Opposite to pci_enable_msi_block() which takes the number of
MSIs to allocate as a input parameter,
pci_enable_msi_block_auto() could be used by device drivers to
obtain the number of assigned MSIs and the number of MSIs the
device supports.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/c3de2419df94a0f95ca1a6f755afc421486455e6.1353324359.git.agordeev@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The ACPI handles of PCI root bridges need to be known to
acpi_bind_one(), so that it can create the appropriate
"firmware_node" and "physical_node" files for them, but currently
the way it gets to know those handles is not exactly straightforward
(to put it lightly).
This is how it works, roughly:
1. acpi_bus_scan() finds the handle of a PCI root bridge,
creates a struct acpi_device object for it and passes that
object to acpi_pci_root_add().
2. acpi_pci_root_add() creates a struct acpi_pci_root object,
populates its "device" field with its argument's address
(device->handle is the ACPI handle found in step 1).
3. The struct acpi_pci_root object created in step 2 is passed
to pci_acpi_scan_root() and used to get resources that are
passed to pci_create_root_bus().
4. pci_create_root_bus() creates a struct pci_host_bridge object
and passes its "dev" member to device_register().
5. platform_notify(), which for systems with ACPI is set to
acpi_platform_notify(), is called.
So far, so good. Now it starts to be "interesting".
6. acpi_find_bridge_device() is used to find the ACPI handle of
the given device (which is the PCI root bridge) and executes
acpi_pci_find_root_bridge(), among other things, for the
given device object.
7. acpi_pci_find_root_bridge() uses the name (sic!) of the given
device object to extract the segment and bus numbers of the PCI
root bridge and passes them to acpi_get_pci_rootbridge_handle().
8. acpi_get_pci_rootbridge_handle() browses the list of ACPI PCI
root bridges and finds the one that matches the given segment
and bus numbers. Its handle is then used to initialize the
ACPI handle of the PCI root bridge's device object by
acpi_bind_one(). However, this is *exactly* the ACPI handle we
started with in step 1.
Needless to say, this is quite embarassing, but it may be avoided
thanks to commit f3fd0c8 (ACPI: Allow ACPI handles of devices to be
initialized in advance), which makes it possible to initialize the
ACPI handle of a device before passing it to device_register().
Accordingly, add a new __weak routine, pcibios_root_bridge_prepare(),
defaulting to an empty implementation that can be replaced by the
interested architecutres (x86 and ia64 at the moment) with functions
that will set the root bridge's ACPI handle before its dev member is
passed to device_register(). Make both x86 and ia64 provide such
implementations of pcibios_root_bridge_prepare() and remove
acpi_pci_find_root_bridge() and acpi_get_pci_rootbridge_handle() that
aren't necessary any more.
Included is a fix for breakage on systems with non-ACPI PCI host
bridges from Bjorn Helgaas.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Firmware may have assigned PCI BARs for hot-added devices, so reserve
those resources before trying to allocate more.
[bhelgaas: move empty weak definition here]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay Pandarathil)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=OE3Q
-----END PGP SIGNATURE-----
Merge tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI update from Bjorn Helgaas:
"Host bridge hotplug:
- Untangle _PRT from struct pci_bus (Bjorn Helgaas)
- Request _OSC control before scanning root bus (Taku Izumi)
- Assign resources when adding host bridge (Yinghai Lu)
- Remove root bus when removing host bridge (Yinghai Lu)
- Remove _PRT during hot remove (Yinghai Lu)
SRIOV
- Add sysfs knobs to control numVFs (Don Dutile)
Power management
- Notify devices when power resource turned on (Huang Ying)
Bug fixes
- Work around broken _SEG on HP xw9300 (Bjorn Helgaas)
- Keep runtime PM enabled for unbound PCI devices (Huang Ying)
- Fix Optimus dual-GPU runtime D3 suspend issue (Dave Airlie)
- Fix xen frontend shutdown issue (David Vrabel)
- Work around PLX PCI 9050 BAR alignment erratum (Ian Abbott)
Miscellaneous
- Add GPL license for drivers/pci/ioapic (Andrew Cooks)
- Add standard PCI-X, PCIe ASPM register #defines (Bjorn Helgaas)
- NumaChip remote PCI support (Daniel Blueman)
- Fix PCIe Link Capabilities Supported Link Speed definition (Jingoo
Han)
- Convert dev_printk() to dev_info(), etc (Joe Perches)
- Add support for non PCI BAR ROM data (Matthew Garrett)
- Add x86 support for host bridge translation offset (Mike Yoknis)
- Report success only when every driver supports AER (Vijay
Pandarathil)"
Fix up trivial conflicts.
* tag 'for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Use phys_addr_t for physical ROM address
x86/PCI: Add NumaChip remote PCI support
ath9k: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: Use standard #defines for PCIe Capability ASPM fields
iwlwifi: collapse wrapper for pcie_capability_read_word()
iwlegacy: Use standard #defines for PCIe Capability ASPM fields
iwlegacy: collapse wrapper for pcie_capability_read_word()
cxgb3: Use standard #defines for PCIe Capability ASPM fields
PCI: Add standard PCIe Capability Link ASPM field names
PCI/portdrv: Use PCI Express Capability accessors
PCI: Use standard PCIe Capability Link register field names
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
PCI: Add and use standard PCI-X Capability register names
PCI/PM: Keep runtime PM enabled for unbound PCI devices
xen-pcifront: Handle backend CLOSED without CLOSING
PCI: SRIOV control and status via sysfs (documentation)
PCI/AER: Report success only when every device has AER-aware driver
...
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
Use phys_addr_t rather than "void *" for physical memory address.
This removes casts and fixes a "cast from pointer to integer of different
size" warning on ppc44x_defconfig.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/mjg-pci-roms-from-efi:
x86: Use PCI setup data
PCI: Add support for non-BAR ROMs
PCI: Add pcibios_add_device
EFI: Stash ROMs if they're not in the PCI BAR
Platforms may provide their own mechanisms for obtaining ROMs. Add support
for using data provided by the platform in that case.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Platforms may want to provide architecture-specific functionality during
PCI enumeration. Add a pcibios_add_device() call that architectures can
override to do so.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p, __devint,
__devinitdata, __devinitconst, and _devexit are no longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an error is detected on a PCIe device which does not have an
AER-aware driver, prevent AER infrastructure from reporting
successful error recovery.
This is because the report_error_detected() function that gets
called in the first phase of recovery process allows forward
progress even when the driver for the device does not have AER
capabilities. It seems that all callbacks (in pci_error_handlers
structure) registered by drivers that gets called during error
recovery are not mandatory. So the intention of the infrastructure
design seems to be to allow forward progress even when a specific
callback has not been registered by a driver. However, if error
handler structure itself has not been registered, it doesn't make
sense to allow forward progress.
As a result of the current design, in the case of a single device
having an AER-unaware driver or in the case of any function in a
multi-function card having an AER-unaware driver, a successful
recovery is reported.
Typical scenario this happens is when a PCI device is detached
from a KVM host and the pci-stub driver on the host claims the
device. The pci-stub driver does not have error handling capabilities
but the AER infrastructure still reports that the device recovered
successfully.
The changes proposed here leaves the device(s)in an unrecovered state
if the driver for the device or for any device in the subtree
does not have error handler structure registered. This reflects
the true state of the device and prevents any partial recovery (or no
recovery at all) reported as successful.
[bhelgaas: changelog]
Signed-off-by: Vijay Mohan Pandarathil <vijaymohan.pandarathil@hp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linas Vepstas <linasvepstas@gmail.com>
Reviewed-by: Myron Stowe <myron.stowe@redhat.com>
- Also refactor the conditional to use the existing tg3_pci_tbl array.
- Set flags in the driver_data field of the pci_device_id structure to
identify these devices.
- Add PCI_DEVICE_SUB() to pci.h to declare PCI 4-part IDs to match these
devices.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pci/don-sriov:
PCI: Remove useless "!dev" tests
PCI: Use spec names for SR-IOV capability fields
PCI: Provide method to reduce the number of total VFs supported
PCI: SRIOV control and status via sysfs
PCI: Use is_visible() with boot_vga attribute for pci_dev
PCI: Add pci_device_type to pdev's device struct
Some implementations of SRIOV provide a capability structure
value of TotalVFs that is greater than what the software can support.
Provide a method to reduce the capability structure reported value
to the value the driver can support.
This ensures sysfs reports the current capability of the system,
hardware and software.
Example for its use: igb & ixgbe -- report 8 & 64 as TotalVFs,
but drivers only support 7 & 63 maximum.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Provide files under sysfs to determine the maximum number of VFs
an SR-IOV-capable PCIe device supports, and methods to enable and
disable the VFs on a per-device basis.
Currently, VF enablement by SR-IOV-capable PCIe devices is done
via driver-specific module parameters. If not setup in modprobe files,
it requires admin to unload & reload PF drivers with number of desired
VFs to enable. Additionally, the enablement is system wide: all
devices controlled by the same driver have the same number of VFs
enabled. Although the latter is probably desired, there are PCI
configurations setup by system BIOS that may not enable that to occur.
Two files are created for the PF of PCIe devices with SR-IOV support:
sriov_totalvfs Contains the maximum number of VFs the device
could support as reported by the TotalVFs register
in the SR-IOV extended capability.
sriov_numvfs Contains the number of VFs currently enabled on
this device as reported by the NumVFs register in
the SR-IOV extended capability.
Writing zero to this file disables all VFs.
Writing a positive number to this file enables that
number of VFs.
These files are readable for all SR-IOV PF devices. Writes to the
sriov_numvfs file are effective only if a driver that supports the
sriov_configure() method is attached.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_ext_cfg_avail() doesn't use the "struct pci_dev *" passed to
it, and there's no requirement that a host bridge even be represented
by a pci_dev. This drops the pci_ext_cfg_avail() parameter.
[bhelgaas: changelog]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It supports both PCI root bus and PCI bus under PCI bridge.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It is main portion of pci_rescan_bus().
Separate it out and prepare to use it for PCI root bus hot add later.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
* pci/trivial:
PCI: Drop duplicate const in DECLARE_PCI_FIXUP_SECTION
PCI: Drop bogus default from ARCH_SUPPORTS_MSI
PCI: cpqphp: Remove unreachable path
PCI: Remove bus number resource debug messages
PCI/AER: Print completion message at KERN_INFO to match starting message
PCI: Fix drivers/pci/pci.c kernel-doc warnings
* pci/stephen-const:
make drivers with pci error handlers const
scsi: make pci error handlers const
netdev: make pci_error_handlers const
PCI: Make pci_error_handlers const
This patch implements a weak function to return the default I/O or memory
window alignment for a P2P bridge. By default, I/O windows are aligned to
4KiB or 1KiB and memory windows are aligned to 4MiB. Some platforms, e.g.,
powernv, have special alignment requirements and can override
pcibios_window_alignment().
[bhelgaas: changelog]
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's redundant and makes sparse complain about it.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since pci_error_handlers is just a function table make it const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
* pci/bjorn-cleanup-remove:
PCI: Remove unused pci_dev_b()
sgi-agp: Use list_for_each_entry() for bus->devices traversal
parisc/PCI: Use list_for_each_entry() for bus->devices traversal
parisc/PCI: Enable PERR/SERR on all devices
frv/PCI: Use list_for_each_entry() for bus->devices traversal
PCI: Leave normal LIST_POISON in deleted list entries
PCI: Rename local variables to conventional names
PCI: Remove unused, commented-out, code
PCI: Stop and remove devices in one pass
PCI: Fold stop and remove helpers into their callers
PCI: Use list_for_each_entry() for bus->devices traversal
PCI: Remove pci_stop_and_remove_behind_bridge()
PCI: Don't export stop_bus_device and remove_bus_device interfaces
pcmcia: Use common pci_stop_and_remove_bus_device()
PCI: acpiphp: Use common pci_stop_and_remove_bus_device()
PCI: acpiphp: Stop disabling bridges on remove
The PCI Express Capability (PCIe spec r3.0, sec 7.8) comes in two
versions, v1 and v2. In v1 Capability structures (PCIe spec r1.0 and
r1.1), some fields are optional, so the structure size depends on the
device type.
This patch adds functions to access this capability so drivers don't
have to be aware of the differences between v1 and v2. Note that these
new functions apply only to the "PCI Express Capability," not to any of
the other "PCI Express Extended Capabilities" (AER, VC, ACS, MFVC, etc.)
Function pcie_capability_read_word/dword() reads the PCIe Capabilities
register and returns the value in the reference parameter "val". If
the PCIe Capabilities register is not implemented on the PCIe device,
"val" is set to 0.
Function pcie_capability_write_word/dword() writes the value to the
specified PCIe Capability register.
Function pcie_capability_clear_and_set_word/dword() sets and/or clears bits
of a PCIe Capability register.
[bhelgaas: changelog, drop "pci_" prefixes, don't export
pcie_capability_reg_implemented()]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
With introduction of pci_pcie_type(), pci_dev->pcie_type field becomes
redundant, so remove it.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some extended capabilities, e.g., the vendor-specific capability, can
occur several times. The existing pci_find_ext_capability() only finds
the first occurrence. This adds pci_find_next_ext_capability(), which
can iterate through all of them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
