The PHY is initialized during device initialization, but devices with
the tx_siso_diversity flag set need to send PHY_CONFIGURATION_CMD first,
otherwise the PHY would be reinitialized, causing a SYSASSERT.
To fix this, use a bit that tells the FW not to complete the PHY
initialization before a PHY_CONFIGURATION_CMD is received.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can't check for the ACPI table revision validity in the same if
where we check if the package was read correctly, because we return
PTR_ERR(pkg) and if the table is not valid but the pointer is, we
would return a valid pointer as an error. Fix that by moving the
table checks to a separate if and return -EINVAL if it's not valid.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We copy cfg->trans to trans->trans_cfg at the very beginning, so don't
try to access it via cfg->trans anymore, because the cfg may be unset
in later cases.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
First set of fixes for 5.4 sent during the merge window. Most are
regressions fixes but the mt7615 problem has been since it was merged.
iwlwifi
* fix a build regression related CONFIG_THERMAL
* avoid using GEO_TX_POWER_LIMIT command on certain firmware versions
rtw88
* fixes for skb leaks
zd1211rw
* fix a compiler warning on 32 bit
mt76
* fix the firmware paths for mt7615 to match with linux-firmware
wil6210
* fix use of skb after free
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdjLN3AAoJEG4XJFUm622bsBcH/1A/srmEN3bME86p9j0DS1Wb
A/8KPP88q9gczIDg+uZQCw1rTqHUrqkgbPxVCa64tKdPjqioRc9nW4CVhKh2OLTy
88Bwh/mJhxfh/+TTfYf397OsHr9NEVaFnEqjYeUxtyhRoZriUmAtKSd4/689czDP
AOdbkXShe8pUS+UvpizfpOHP28j4TbFOzcWn8qcGm1gqfuCHan+giaSw073vz+r4
fagOz470huyqCwx8LB21IzTCunox20W4IfN/G2AMoKx7tE9XbYr6kRR8vawffwm2
FVyhlnibkRQnRv77thg+zJZQ6UpJybsfM8Izpn1kTDFiRChNqvMtOKboz+IQOHg=
=4i7U
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-09-26' of https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.4
First set of fixes for 5.4 sent during the merge window. Most are
regressions fixes but the mt7615 problem has been since it was merged.
iwlwifi
* fix a build regression related CONFIG_THERMAL
* avoid using GEO_TX_POWER_LIMIT command on certain firmware versions
rtw88
* fixes for skb leaks
zd1211rw
* fix a compiler warning on 32 bit
mt76
* fix the firmware paths for mt7615 to match with linux-firmware
wil6210
* fix use of skb after free
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intention was to have the GEO_TX_POWER_LIMIT command in FW version
36 as well, but not all 8000 family got this feature enabled. The
8000 family is the only one using version 36, so skip this version
entirely. If we try to send this command to the firmwares that do not
support it, we get a BAD_COMMAND response from the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=204151.
Cc: stable@vger.kernel.org # 4.19+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without CONFIG_THERMAL, the driver fails to link as it calls
iwl_mvm_send_temp_report_ths_cmd() unconditionally. Fix this
by making that function available, but do almost nothing but
send the empty firmware command to enable CT-kill reporting.
While at it, also fix that function itself to not error out
when the thermal zone hasn't been initialized, but instead
just send the empty firmware command in this case as well.
Fixes: 242d9c8b9a ("iwlwifi: mvm: use FW thermal monitoring regardless of CONFIG_THERMAL")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use cancel_delayed_work_sync on the dump workers only in case of
unloading the op mode. In any other case use iwl_fw_flush_dumps or
iwl_fw_dbg_stop_sync (depends if the op mode mutex is held or not).
This way, the driver will wait until debug data is collected in all
cases but op mode unloading.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove periodic trigger functionality.
After moving to the new API we will add periodic trigger functionality
that matches the new API.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix the documentation of struct iwl_fw_ini_monitor_dump and
iwl_fw_ini_error_dump_range.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support code to be able to use the DRAM buffer allocation command,
which allows us to send information about a buffer to the firmware
to use it with the DBGC hardware.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the "apply points" mechanism as preparation for the changed
debug API where this is now a "time point" instead. Use a new API
across the code at the trigger points ("time points"), but don't
yet implement it since that requires some more preparation.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allows to easily calculate array length at the end of a TLV.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes the firmware won't be able to decrypt frames
because the keys were not installed yet or other scenarios.
The firmware will soon stop dropping multicast frames when
MAC_FILTER_ACCEPT_GRP is not set. The firmware will simply
always pass multicast frame in.
In order to avoid logging any such frame coming in when we
don't have the keys, drop the print.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are products which have a single chain with 2 antennas.
In these products, we need to inform the FW that the device has the
single antenna diversity(SAD) feature. In the future, we will read
the active antenna from a BIOS configuration. Currently, we use a
default configuration which means that the FW decides which antenna to use.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In prior hardware generations (e.g. 9000 series), we received the BAR
frame with fake NSSN information to handle releasing frames from the
reorder buffer for the default queue, the other queues were getting
the FRAME_RELEASE notification in this case.
With multi-TID block-ack, the firmware no longer sends us the BAR
frame because the fake RX is quite big (just the metadata is around
48 bytes or so). Instead, it now sends us one (or multiple) special
release notifications (0xc2). The hardware consumes these as well,
but only generates the FRAME_RELEASE (0xc3) for queues other than
the default queue. We thus need to handle them in the same way we
handle the normal FRAME_RELEASE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Certain APs (I think a certain Broadcom model) interact badly with our
full state BA bitmap handling, and if triggered badly with many powersave
transitions they keep sending frames from before the window, which our
hardware then doesn't appear to ACK (to them) since it has moved on and
is sending ACKs for higher SNs now.
Try to detect this situation and if this keeps happening, disable the
aggregation session.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
WoWlan feature within the FW uses the station id for various of reasons.
Thus we need to add this information to the command.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new device generation has a slightly different suspend resume flow
Currently, the way the driver instruct the device to move to D3 is by
sending D3_CONFIG_CMD.
Instead of using the host command the indication is by writing to the
doorbell interrupt.
The FW will respond with interrupt to indicate transition completion.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove duplicate inclusion of iwl-trans.h.
This issue was found by includecheck.
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few functions were receiving the iwl_cfg struct directly, but we
will also need other parts of the trans, so pass the trans (which
includes the cfg) to them.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of accessing the iwl_config_trans_params from the cfg that is
stored in the trans struct, pass this structure directly to functions
that need it during trans_alloc. This will be useful to isolate the
elements needed during allocation and pass them separately before the
actual cfg struct is known.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the cfg to iwl_trans already during allocation, set
it only later when we have had the time to decide which cfg to use.
This is part of the effort to be able to decide the cfg based on HW
revision and RF ID after iwl_trans_alloc() has been called.
For now, since we still have a bunch of code checking the HW revision
and the RF ID, we set iwl_trans->cfg early, even before we decided the
real cfg to use. We only use the trans configuration at this point,
so this is fine for now. In the future, the trans configuration will
be completely independent from the rest of the config structure, so
we'll be able to avoid this.
Additionally, we can't access the PRPH registers in iwl_trans_alloc()
anymore, so move the HW REV C-step check for family 8000 code later to
the probe function as well. This step is probably not necessary, but
if that's the case it should be removed separately later on.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There were a couple of special handling to find the correct cfg inside
iwl_trans_pcie_alloc(). Move them to iwl_pci_probe() so they're
together with the rest of the decisions.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of using iwl_trans->cfg in iwl_trans_pcie_alloc(), use the
local argument that we received. This will allow us to not to set the
cfg during iwl_trans_alloc() so it can be decided later.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make a static regions ops array and use it instead of switch case when
determining what op to use to collect a region.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Avoid iterating over dump TLVs twice for size calculation by using
linked list to store the dump TLVs.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
separate configuration flows and dump collection flows.
make ini configuration flows be in iwl-dbg-tlv.c and dump related flows
in dbg.c to better reflect their logical difference.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Can't rely that band 2.4 is always supported by the NIC and use the
first channel in this band for the phy ctxt.
Instead, look for the first channel in the first band that is supported
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of Ultra-high-band (UHB), need to allocate nvm data structure in
size of UHB channels array.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the IWL_DEVICE_AX200_COMMON definition, since it's only used
once and relies mostly on IWL_DEVICE_22000_COMMON anyway.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Align wrt log prints to the driver coding style
Remove the ext field from the log and print it at the beginning of the
apply point.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Debug flow TLV was removed from the FW. Remove the TLV from the driver
as well.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reimplement debug TLV allocation flow. The driver will check the
validity of the debug TLVs prior allocating space for them.
Any malformed or unsupported TLV will be skipped.
The TLV specific checks will be added in later patches.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
use iwl_trans_dbg_ini_valid function instead of a boolean value check if
dbg_ini mode is on. It is needed for a future patch.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The string we define as IWL_22000_HR_B_F0_FW_PRE is duplicate with
IWL_22000_QU_B_HR_B_FW_PRE. Remove the former to avoid confusion.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The real name is struct iwl_tof_range_req_ext_cmd, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TX power limits as defined in the OTP assume the worst case scenario
in terms of the platform's atenna gain, but most platforms are below
that value so they can use more TX power without passing the regulatory
limit. If the platform indicates in the BIOS that it indeed has lower
gain, and the geographic location allows it, higher TX power can be
used. The driver reads the PPAG (Per-Platform Antenna Gain) data from
BIOS (if it exists), validates it and sends the appropriate command to
the FW. This flow happens once at FW init, in case of suspend/resume
there is no need to read again from BIOS as we save those values during
init, so just send the PPAG command again to FW.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The check is not necessary anymore, because now the struct is not
allocated separately, but is part of the mvmsta struct. Remove the
check, since it's dead code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Any firmware that supports the new channel switch flow is
able to close / re-open the queues when needed. It takes
into account the channel switch mode etc...
Don't open / close the queues or enable / disable beacon
abort before and after the channel switch in case the
firmware is able to do this by itself.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
dma_alloc_coherent is not just the page allocator. The only valid
arguments to pass are either GFP_ATOMIC or GFP_ATOMIC with possible
modifiers of __GFP_NORETRY or __GFP_NOWARN.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
