* Allow setting of adaptive coalescing setting for all types of interrupt.
* In msi & legacy intr, we use single interrupt for rx & tx. In this case
tx_coalesce_usecs is invalid. We should use only rx_coalesce_usecs.
Do not display tx_coal values for msi/intx. And do not allow user to set
this as well.
* Driver supports only tx/rx_coalesce_usec and adaptive coalesce settings.
For other values, driver does not return error. So ethtool succeeds for
unsupported values. Introduce enic_coalesce_valid() function to validate
the coalescing values.
* If user requests for coalesce value greater than what adaptor supports,
driver uses the max value. We should at least log this.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adaptive interrupt coalescing is available for msix. This patch adds the support
for msi poll. Interface for adaptive interrupt coalescing is already added in
driver. We just did not enable it for legacy intr & msi.
enic_calc_int_moderation() & enic_set_int_moderation() are defined as static
after enic_poll. Since enic_poll needs it, move both of these function
definitions above enic_poll. No change in functionality.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In enic_poll, we clean tx and rx queues, when low latency busy socket polling
is happening, enic_poll will only clean tx queue. After cleaning tx, it should
return total budget for re-poll.
There is a small window between vnic_intr_unmask() and enic_poll_unlock_napi().
In this window if an irq occurs and napi is scheduled on different cpu, it tries
to acquire enic_poll_lock_napi() and fails. Unlock napi_poll before unmasking
the interrupt.
v2:
Do not change tx wonk done behaviour. Consider only rx work done for completing
napi.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use spinlock to access a single flag. We can avoid spin_locks by using
atomic variable and atomic_cmpxchg(). Use atomic_cmpxchg to set the flag
for idle to poll. And a simple atomic_set to unlock (set idle from poll).
In napi poll, if gro is enabled, we call napi_gro_receive() to deliver the
packets. Before we call napi_complete(), i.e while re-polling, if low
latency busy poll is called, we use netif_receive_skb() to deliver the packets.
At this point if there are some skb's held in GRO, busy poll could deliver the
packets out of order. So we call napi_gro_flush() to flush skbs before we
move the napi poll to idle.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not check the return value of enic_dev_stats_dump(). If allocation
fails, we will hit NULL pointer reference.
Return only if memory allocation fails. For other failures, we return the
previously recorded values.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds full IPv6 addresses into flow_keys and uses them as
input to the flow hash function. The implementation supports either
IPv4 or IPv6 addresses in a union, and selector is used to determine
how may words to input to jhash2.
We also add flow_get_u32_dst and flow_get_u32_src functions which are
used to get a u32 representation of the source and destination
addresses. For IPv6, ipv6_addr_hash is called. These functions retain
getting the legacy values of src and dst in flow_keys.
With this patch, Ethertype and IP protocol are now included in the
flow hash input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should complete notify_check before returning the credits. Once we return the
credits, adaptor may access the notify data.
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warnings:
enic_main.c:92:28: warning: symbol 'mod_table' was not declared. Should it be static?
enic_main.c:109:28: warning: symbol 'mod_range' was not declared. Should it be static?
enic_main.c:1306:5: warning: symbol 'enic_busy_poll' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warning:
enic_ethtool.c:95:6: warning: symbol 'enic_intr_coal_set_rx' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the commit d75b1ade56 ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. When we are in busy_poll we return 0 in
napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in kdump kernel, reduce number of resources used by the driver.
This will enable NIC to operate in low memory kdump kernel environment.
Also change the driver version to .83
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocation of all RQs fail, we do not free previously allocated buffers,
before returning error. This causes memory leak.
This patch fixes this by calling vnic_rq_clean(), which frees all the rq
buffers.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes some functions that are not used anywhere:
enic_dev_enable2_done() enic_dev_enable2() enic_dev_deinit_done()
enic_dev_init_prov2() enic_vnic_dev_deinit()
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds generic statistics for enic. As of now dma_map_error is the only
member. dma_map_erro is incremented every time dma maping error happens.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch checks for pci_dma_mapping_error() after dma mapping the data.
If the dma mapping fails we remove the previously queued frags and return
NETDEV_TX_OK.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes vnic_wq_buf doubly liked list. This is needed for dma_mapping
error check, in case some frag's dma map fails, we need to move back and remove
previously queued buffers.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting/getting rss hash key using ethtool.
v2:
respin patch to support RSS hash function changes.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of well known RSS key might increase attack surface.
Switch to a random one, using generic helper so that all
ports share a common key.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Govindarajulu Varadarajan <_govind@gmx.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the access to wq has been moved out of hardirq context. We no longer need to
use spin_lock_irqsave.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic_isr_legacy(), enic_isr_msix() & enic_isr_msi() run from hard
interrupt context.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check and update posted_index only when skb->xmit_more is 0 or tx queue is full.
v2:
use txq_map instead of skb_get_queue_mapping(skb)
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the commit d75b1ade56 ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. In tx napi poll we always return 0.
So tx napi is not called again and we do not clean up the tx ring.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following warning is shown when spinlock debug is enabled.
This occurs when enic_flow_may_expire timer function is running and
enic_stop is called on same CPU.
Fix this by using spink_lock_bh().
=================================
[ INFO: inconsistent lock state ]
3.17.0-netnext-05504-g59f35b8 #268 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
ifconfig/443 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&enic->rfs_h.lock)->rlock){+.?...}, at:
enic_rfs_flw_tbl_free+0x34/0xd0 [enic]
{IN-SOFTIRQ-W} state was registered at:
[<ffffffff810a25af>] __lock_acquire+0x83f/0x21c0
[<ffffffff810a45f2>] lock_acquire+0xa2/0xd0
[<ffffffff814913fc>] _raw_spin_lock+0x3c/0x80
[<ffffffffa029c3d5>] enic_flow_may_expire+0x25/0x130[enic]
[<ffffffff810bcd07>] call_timer_fn+0x77/0x100
[<ffffffff810bd8e3>] run_timer_softirq+0x1e3/0x270
[<ffffffff8105f9ae>] __do_softirq+0x14e/0x280
[<ffffffff8105fdae>] irq_exit+0x8e/0xb0
[<ffffffff8103da0f>] smp_apic_timer_interrupt+0x3f/0x50
[<ffffffff81493742>] apic_timer_interrupt+0x72/0x80
[<ffffffff81018143>] default_idle+0x13/0x20
[<ffffffff81018a6a>] arch_cpu_idle+0xa/0x10
[<ffffffff81097676>] cpu_startup_entry+0x2c6/0x330
[<ffffffff8103b7ad>] start_secondary+0x21d/0x290
irq event stamp: 2997
hardirqs last enabled at (2997): [<ffffffff81491865>] _raw_spin_unlock_irqrestore+0x65/0x90
hardirqs last disabled at (2996): [<ffffffff814915e6>] _raw_spin_lock_irqsave+0x26/0x90
softirqs last enabled at (2968): [<ffffffff813b57a3>] dev_deactivate_many+0x213/0x260
softirqs last disabled at (2966): [<ffffffff813b5783>] dev_deactivate_many+0x1f3/0x260
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&enic->rfs_h.lock)->rlock);
<Interrupt>
lock(&(&enic->rfs_h.lock)->rlock);
*** DEADLOCK ***
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting/getting rx_copybreak using
generic ethtool tunable.
Defines enic_get_tunable() & enic_set_tunable() to get/set rx_copybreak.
As of now, these two function supports only rx_copybreak.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Sujith Sankar <ssujith@cisco.com>
Cc: Govindarajulu Varadarajan <_govind@gmx.com>
Cc: Neel Patel <neepatel@cisco.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch impliments ethtool_ops->get_rxnfc() to display the classifier
filter added by the driver.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the #ifdef CONFIG_RFS_ACCEL around the classifier filter
structures. This makes the filter structures available when CONFIG_RFS_ACCEL = n.
Introduce enic_rfs_timer_start() & enic_rfs_timer_stop() to start/stop the
timer. These two functions are nop when CONFIG_RFS_ACCEL = n.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic_set_coalesce() has two problems.
* It should return -EINVAL and not -EOPNOTSUPP for invalid coalesce values.
* In case of MSIX, enic_set_coalesce return error after applying requested
coalescing setting partially. We should either apply all the setting requeste
and return success or apply non and return error.
* This patch also simplifies the algo.
This was introduced by
'7c2ce6e60f703 enic: Add support for adaptive interrupt coalescing'
These changes were suggested by Ben Hutchings here
http://www.spinics.net/lists/netdev/msg283972.html
Also change enic driver version.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_RFS_ACCEL=n:
drivers/net/ethernet/cisco/enic/enic_main.c: In function 'enic_open':
drivers/net/ethernet/cisco/enic/enic_main.c:1603:2: error: implicit declaration of function 'enic_rfs_flw_tbl_init' [-Werror=implicit-function-declaration]
drivers/net/ethernet/cisco/enic/enic_main.c: In function 'enic_stop':
drivers/net/ethernet/cisco/enic/enic_main.c:1630:2: error: implicit declaration of function 'enic_rfs_flw_tbl_free' [-Werror=implicit-function-declaration]
Introduced in commit a145df23ef ("enic: Add
Accelerated RFS support").
Dummy functions are provided, but their prototypes are missing, causing the
build failure. Provide dummy static inline functions instead to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
