Fix timeout recover function to return a meaningful return value.
When an interrupt was not sent by the FW, return IO error instead of
'true'.
Fixes: c7981bea48 ("net/mlx5e: Fix return status of TX reporter timeout recover")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
CQE checksum full mode in new HW, provides a full checksum of rx frame.
Covering bytes starting from eth protocol up to last byte in the received
frame (frame_size - ETH_HLEN), as expected by the stack.
Fixing up skb->csum by the driver is not required in such case. This fix
is to avoid wrong checksum calculation in drivers which already support
the new hardware with the new checksum mode.
Fixes: 85327a9c41 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
GRE entropy calculation is a single bit per card, and not per port.
Force disable GRE entropy calculation upon the first GRE encap rule,
and release the force at the last GRE encap rule removal. This is done
per port.
Fixes: 97417f6182 ("net/mlx5e: Fix GRE key by controlling port tunnel entropy calculation")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Encap mode is related to switchdev mode only. Move the init of
the encap mode to eswitch_offloads. Before this change, we reported
that eswitch supports encap, even tough the device was in non
SRIOV mode.
Fixes: 7768d1971d ('net/mlx5: E-Switch, Add control for encapsulation')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
clang warns:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c:251:2:
warning: variable 'rec_seq_sz' is used uninitialized whenever switch
default is taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c:255:46: note:
uninitialized use occurs here
skip_static_post = !memcmp(rec_seq, &rn_be, rec_seq_sz);
^~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ktls_tx.c:239:16: note:
initialize the variable 'rec_seq_sz' to silence this warning
u16 rec_seq_sz;
^
= 0
1 warning generated.
This case statement was clearly designed to be one that should not be
hit during runtime because of the WARN_ON statement so just return early
to prevent copying uninitialized memory up into rn_be.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Link: https://github.com/ClangBuiltLinux/linux/issues/590
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return value was changes to 'int' from void but this return statement
was not updated, or it slipped in via a merge.
Fixes: b5d9a834f4 ("net/tls: don't clear TX resync flag on error")
Signed-off-by: David S. Miller <davem@davemloft.net>
On commit ba2b232108 ("net: netsec: add XDP support") a static
declaration for netsec_set_tx_de() was added to make the diff easier
to read. Now that the patch is merged let's move the functions around
and get rid of that
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While freeing tx buffers the memory has to be unmapped if the packet was
an skb or was used for .ndo_xdp_xmit using the same arguments. Get rid
of the unneeded extra 'else if' statement
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
And any other existing fields in this structure that refer to tc.
Specifically:
* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to check if flow block callback is already in
use. Call this new function from flow_block_cb_setup_simple() and from
drivers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and
remove temporary tcf_block_binder_type alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most drivers do the same thing to set up the flow block callbacks, this
patch adds a helper function to do this.
This preparation patch reduces the number of changes to adapt the
existing drivers to use the flow block callback API.
This new helper function takes a flow block list per-driver, which is
set to NULL until this driver list is used.
This patch also introduces the flow_block_command and
flow_block_binder_type enumerations, which are renamed to use
FLOW_BLOCK_* in follow up patches.
There are three definitions (aliases) in order to reduce the number of
updates in this patch, which go away once drivers are fully adapted to
use this flow block API.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1 changed the offsets and bitmaps for tx_desc
registers in the same peripheral device on different
models of the hip04_eth.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1 changed the offsets and bitmaps for rx_desc
registers in the same peripheral device on different
models of the hip04_eth.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buf unit size of HI13X1_GMAC is cache_line_size,
which is 64, so the address we write to the buf register
needs to be shifted right by 6 bits.
The 31st bit of the PPE_CFG_CPU_ADD_ADDR register
of HI13X1_GMAC indicates whether to release the buffer
of the message, and the low indicates that it is valid.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, group is the same as the port, but some
boards specify a special group for better load
balancing of each processing unit.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1_GMAC delete request for soft reset at first,
otherwise, the subsequent initialization will not
take effect.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HI13X1_GMAC changed the offsets and bitmaps for
GE_TX_LOCAL_PAGE_REG registers in the same peripheral
device on different models of the hip04_eth. With the
default configuration, HI13X1_GMAC can also work without
any writes to the GE_TX_LOCAL_PAGE_REG register.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warning from sparse:
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:533:23: warning: cast to restricted __be16
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
hip04_eth.c:534:23: warning: cast to restricted __be32
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warning from sparse:
hip04_eth.c:468:25: warning: incorrect type in assignment
hip04_eth.c:468:25: expected unsigned int [usertype] send_addr
hip04_eth.c:468:25: got restricted __be32 [usertype]
hip04_eth.c:469:25: warning: incorrect type in assignment
hip04_eth.c:469:25: expected unsigned int [usertype] send_size
hip04_eth.c:469:25: got restricted __be32 [usertype]
hip04_eth.c:470:19: warning: incorrect type in assignment
hip04_eth.c:470:19: expected unsigned int [usertype] cfg
hip04_eth.c:470:19: got restricted __be32 [usertype]
hip04_eth.c:472:23: warning: incorrect type in assignment
hip04_eth.c:472:23: expected unsigned int [usertype] wb_addr
hip04_eth.c:472:23: got restricted __be32 [usertype]
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the hip04_eth driver to support HI13X1_GMAC.
Enable it with CONFIG_HI13X1_GMAC option.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. get hash table size in hw feature reigster, and add support
for taller hash table(128/256) in dwmac4.
2. only clear GMAC_PACKET_FILTER bits used in this function,
to avoid side effect to functions of other bits.
stmmac selftests output log with flow control on:
ethtool -t eth0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters 0
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control 0
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac address array size is GMAC_MAX_PERFECT_ADDRESSES,
so the 'reg' should be less than it, or will affect other registers.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer probing of the orion-mdio interface when getting a clock returns
EPROBE_DEFER. This avoids locking up the Armada 8k SoC when mdio is used
before all clocks have been enabled.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print a warning when device tree specifies more than the maximum of four
clocks supported by orion-mdio. Because reading from mdio can lock up
the Armada 8k when a required clock is not initialized, it is important
to notify the user when a specified clock is ignored.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow up to four clocks to be specified and enabled for the orion-mdio
interface, which are required by the Armada 8k and defined in
armada-cp110.dtsi.
Fixes a hang in probing the mvmdio driver that was encountered on the
Clearfog GT 8K with all drivers built as modules, but also affects other
boards such as the MacchiatoBIN.
Cc: stable@vger.kernel.org
Fixes: 96cb434238 ("net: mvmdio: allow up to three clocks to be specified for orion-mdio")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver starts using page_pool buffers before calling
xdp_rxq_info_reg_mem_model(). Start using the buffers after the
registration succeeded, so we won't have to call
page_pool_request_shutdown() in case of failure
Fixes: 5c67bf0ec4 ("net: netsec: Use page_pool API")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
Mapping and unmapping DMA region is an high bottleneck in stmmac driver,
specially in the RX path.
This commit introduces support for Page Pool API and uses it in all RX
queues. With this change, we get more stable troughput and some increase
of banwidth with iperf:
- MAC1000 - 950 Mbps
- XGMAC: 9.22 Gbps
Changes from v3:
- Use page_pool_destroy() (Ilias)
Changes from v2:
- Uncoditionally call page_pool_free() (Jesper)
Changes from v1:
- Use page_pool_get_dma_addr() (Jesper)
- Add a comment (Jesper)
- Add page_pool_free() call (Jesper)
- Reintroduce sync_single_for_device (Arnd / Ilias)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a993db88d1 ("net: stmmac: Enable support for > 32 Bits
addressing in XGMAC"), introduced support for > 32 bits addressing in
XGMAC but the conversion of descriptors to dma_addr_t was left out.
As some devices assing coherent memory in regions > 32 bits we need to
set lower and upper value of descriptors address when initializing DMA
channels.
Luckly, this was working for me because I was assigning CMA to < 4GB
address space for performance reasons.
Fixes: a993db88d1 ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for coalescing RX path by specifying number of frames which
don't need to have interrupt on completion bit set.
This is only available when RX Watchdog is enabled.
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add page_pool_destroy() in bnxt_free_rx_rings() during normal RX ring
cleanup, as Ilias has informed us that the following commit has been
merged:
1da4bbeffe ("net: core: page_pool: add user refcnt and reintroduce page_pool_destroy")
The special error handling code to call page_pool_free() can now be
removed. bnxt_free_rx_rings() will always be called during normal
shutdown or any error paths.
Fixes: 322b87ca55 ("bnxt_en: add page_pool support")
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Cc: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register devlink port of physical port, PCI PF and PCI VF flavour
for each PF, VF when a given devlink instance is in switchdev mode.
Implement ndo_get_devlink_port callback API to make use of registered
devlink ports.
This eliminates ndo_get_phys_port_name() and ndo_get_port_parent_id()
callbacks. Hence, remove them.
An example output with 2 VFs, without a PF and single uplink port is
below.
$devlink port show
pci/0000:06:00.0/65535: type eth netdev ens2f0 flavour physical
pci/0000:05:00.0/1: type eth netdev eth1 flavour pcivf pfnum 0 vfnum 0
pci/0000:05:00.0/2: type eth netdev eth2 flavour pcivf pfnum 0 vfnum 1
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver has to drop the TLS frame it needs to undo the TCP
sequence tracking changes, otherwise device will receive
segments out of order and drop them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the #ifdef CONFIG_TLS_DEVICE a little so we can eliminate
the other one.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the contents of the skb which carried key material
to the FW is cleared.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a return code for the tls_dev_resync callback.
When the driver TX resync fails, kernel can retry the resync again
until it succeeds. This prevents drivers from attempting to offload
TLS packets if the connection is known to be out of sync.
We don't worry about the RX resync since they will be retried naturally
as more encrypted records get received.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count the number of successfully submitted TLS segments,
not skbs. This will make it easier to compare the TLS
encryption count against other counters.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the batch limit to consume small message bursts more
effectively. Practically, the effect on the 'add' messages is not
significant since the mailbox is sized such that the 'add' messages are
still limited to the same order of magnitude that it was originally set
for.
Furthermore, increase the queue size limit to 1024 entries. This further
improves the handling of bursts of small control messages.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Connection 4 tuple reuse is slightly problematic - TLS socket
and context do not get destroyed until all the associated skbs
left the system and all references are released. This leads
to stale connection entry in the device preventing addition
of new one if the 4 tuple is reused quickly enough.
Instead of using read 4 tuple as the key use a unique ID.
Set the protocol to TCP and port to 0 to ensure no collisions
with real connections.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Long lines are ugly. No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to do our best not to drop delete commands, otherwise
we will have stale entries in the connection table. Ignore
the control message queue limits for delete commands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_dn variable is still being used in of_phy_connect() after the
of_node_put() call, which may result in use-after-free.
Fixes: 1dd2d06c04 ("net: Rework pasemi_mac driver to use of_mdio infrastructure")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible use-after-free issue in the axienet_probe():
1701: np = of_parse_phandle(pdev->dev.of_node, "axistream-connected", 0);
1702: if (np) {
...
1787: of_node_put(np); ---> released here
1788: lp->eth_irq = platform_get_irq(pdev, 0);
1789: } else {
...
1801: }
1802: if (IS_ERR(lp->dma_regs)) {
...
1805: of_node_put(np); ---> double released here
1806: goto free_netdev;
1807: }
We solve this problem by removing the unnecessary of_node_put().
Fixes: 28ef9ebdb6 ("net: axienet: make use of axistream-connected attribute optional")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Anirudha Sarangi <anirudh@xilinx.com>
Cc: John Linn <John.Linn@xilinx.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Robert Hancock <hancock@sedsystems.ca>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
DWMAC4 is capable to support clause 45 mdio communication.
This patch enable the feature on stmmac_mdio_write() and
stmmac_mdio_read() by following phy_write_mmd() and
phy_read_mmd() mdiobus read write implementation format.
Reviewed-by: Li, Yifan <yifan2.li@intel.com>
Signed-off-by: Kweh Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Users can specify classification actions based on the 'ether' flow type.
In that case, this will apply to all ethernet traffic, superseeding
flows such as 'udp4' or 'tcp6'.
Add support for this flow type in the PPv2 classifier, by mapping the
ETHER_FLOW value to the corresponding entries in the classifier.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing check to detect flow types that we don't support, so that
user can be informed of this.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return negative error code -EINVAL from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 1f35a56cf5 ("nfp: tls: add/delete TLS TX connections")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes contention over page allocation for XDP_REDIRECT actions by
adding page_pool support per queue for the driver. The performance for
XDP_REDIRECT actions scales linearly with the number of cores performing
redirect actions when using the page pools instead of the standard page
allocator.
v2: Fix up the error path from XDP registration, noted by Ilias Apalodimas.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic support for XDP_REDIRECT in the bnxt_en driver. Next
patch adds the more optimized page pool support.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__bnxt_xmit_xdp() is used by XDP_TX and ethtool loopback packet transmit.
Refactor it so that it can be re-used by the XDP_REDIRECT logic.
Restructure the TX interrupt handler logic to cleanly separate XDP_TX
logic in preparation for XDP_REDIRECT.
Acked-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming bnxt_xmit_xdp to __bnxt_xmit_xdp to get ready for XDP_REDIRECT
support and reduce confusion/namespace collision.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add XDP support based on rx page_pool allocator, one frame per page.
Page pool allocator is used with assumption that only one rx_handler
is running simultaneously. DMA map/unmap is reused from page pool
despite there is no need to map whole page.
Due to specific of cpsw, the same TX/RX handler can be used by 2
network devices, so special fields in buffer are added to identify
an interface the frame is destined to. Thus XDP works for both
interfaces, that allows to test xdp redirect between two interfaces
easily. Also, each rx queue have own page pools, but common for both
netdevs.
XDP prog is common for all channels till appropriate changes are added
in XDP infrastructure. Also, once page_pool recycling becomes part of
skb netstack some simplifications can be added, like removing
page_pool_release_page() before skb receive.
In order to keep rx_dev while redirect, that can be somehow used in
future, do flush in rx_handler, that allows to keep rx dev the same
while redirect. It allows to conform with tracing rx_dev pointed
by Jesper.
Also, there is probability, that XDP generic code can be extended to
support multi ndev drivers like this one, using same rx queue for
several ndevs, based on switchdev for instance or else. In this case,
driver can be modified like exposed here:
https://lkml.org/lkml/2019/7/3/243
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's possible to set channel num while interfaces are down. When
interface gets up it should resplit budget. This resplit can happen
after phy is up but only if speed is changed, so should be set before
this, for this allow it to happen while changing number of channels,
when interfaces are down.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's possible to set ring params while interfaces are down. When
interface gets up it uses number of descs to fill rx queue and on
later on changes to create rx pools. Usually, this resplit can happen
after phy is up, but it can be needed before this, so allow it to
happen while setting number of rx descs, when interfaces are down.
Also, if no dependency on intf state, move it to cpdma layer, where
it should be.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case if dma mapped packet needs to be sent, like with XDP
page pool, the "mapped" submit can be used. This patch adds dma
mapped submit based on regular one.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper recently removed page_pool_destroy() (from driver invocation)
and moved shutdown and free of page_pool into xdp_rxq_info_unreg(),
in-order to handle in-flight packets/pages. This created an asymmetry
in drivers create/destroy pairs.
This patch reintroduce page_pool_destroy and add page_pool user
refcnt. This serves the purpose to simplify drivers error handling as
driver now drivers always calls page_pool_destroy() and don't need to
track if xdp_rxq_info_reg_mem_model() was unsuccessful.
This could be used for a special cases where a single RX-queue (with a
single page_pool) provides packets for two net_device'es, and thus
needs to register the same page_pool twice with two xdp_rxq_info
structures.
This patch is primarily to ease API usage for drivers. The recently
merged netsec driver, actually have a bug in this area, which is
solved by this API change.
This patch is a modified version of Ivan Khoronzhuk's original patch.
Link: https://lore.kernel.org/netdev/20190625175948.24771-2-ivan.khoronzhuk@linaro.org/
Fixes: 5c67bf0ec4 ("net: netsec: Use page_pool API")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF is disabled, we get a harmless warning about the
newly added variable:
drivers/net/ethernet/cadence/macb_main.c:48:39: error: 'mgmt' defined but not used [-Werror=unused-variable]
static struct sifive_fu540_macb_mgmt *mgmt;
Move the variable closer to its use inside of the #ifdef.
Fixes: c218ad5590 ("macb: Add support for SiFive FU540-C000")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On unusual page sizes, we get harmless warnings:
drivers/net/ethernet/google/gve/gve_rx.c:283:6: error: unused variable 'pagecount' [-Werror,-Wunused-variable]
drivers/net/ethernet/google/gve/gve_rx.c:336:1: error: unused label 'have_skb' [-Werror,-Wunused-label]
Change the preprocessor #if to regular if() to avoid this.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
"This is the wrong place to change the queue mapping.
stmmac_xmit() is called with a specific TX queue locked,
and accessing a different TX queue results in a data race
for all of that queue's state.
I think this commit should be reverted upstream and in all
stable branches. Instead, the driver should implement the
ndo_select_queue operation and override the queue mapping there."
Fixes: c5acdbee22 ("net: stmmac: Send TSO packets always from Queue 0")
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only at notice level but it was pointed out that no other driver
does this.
Also there is no action the user can take as it is really a property of
the server.
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cd1973a921 ("net: netsec: Sync dma for device on buffer allocation")
was merged on it's v1 instead of the v3.
Merge the proper patch version
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds firmware version query in ethtool -i.
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: f5cedc84a3 ("gve: Add transmit and receive support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probable cut&paste typo - use the correct field size.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Probable cut&paste typo - use the correct field size.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch syncs the name of few chip versions with the latest vendor
driver version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for transmit side kernel-TLS acceleration.
Offload the crypto encryption to HW.
Per TLS connection:
- Use a separate TIS to maintain the HW context.
- Use a separate encryption key.
- Maintain static and progress HW contexts by posting the proper
WQEs at creation time, or upon resync.
- Use a special DUMP opcode to replay the previous frags and sync
the HW context.
To make sure the SQ is able to serve an xmit request, increase
SQ stop room to cover:
- static params WQE,
- progress params WQE, and
- resync DUMP per frag.
Currently supporting TLS 1.2, and key size 128bit.
Tested over SimX simulator.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the existing mlx5e_post_nop(), but marks a fence
in the WQE control segment.
Added as a separate new function to not hurt the performance
of the common case.
To be used in a downstream patch of the series.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let the EN TIS creation function (mlx5e_create_tis) be responsible
for applying common mdev related fields.
Other specific fields must be set by the caller and passed within
the inbox.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use an SQ field for stop_room, and use the larger value only if TLS
is supported.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When polling a CQE of an SKB-less WQE, don't assume it consumed only
one WQEBB. Use wi->num_wqebbs directly instead.
In the downstream patch, SKB-less WQEs might have more the one WQEBB,
thus this change is needed.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change mlx5e_sq_fetch_wqe to be agnostic to the Work Queue
Element (WQE) type.
Before this patch, it was specific for struct mlx5e_tx_wqe.
In order to allow the change, the function now returns the
generic void pointer, and gets the WQE size to do the zero
memset.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ctrl->tisn field exists, this indicates an operation (HW offload)
on the TCP payload.
For such WQEs, inline the headers up to L4.
This is in preparation for kTLS HW offload support, added in
a downstream patch.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take datapath helper functions to a new header file en/txrx.h.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the new TLS implementation of the Connect-X family.
Introduce a new compilation flag MLX5_TLS for it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Encryption key create / destroy is done via
CREATE_GENERAL_OBJECT / DESTROY_GENERAL_OBJECT commands.
To be used in downstream patches by TLS API wrappers, to configure
the TIS context with the encryption key.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always contain all acceleration functions declarations in
'accel' files, independent to the flags setting.
For this, introduce new flags CONFIG_FPGA_{IPSEC/TLS} and use stubs
where needed.
This obsoletes the need for stubs in 'fpga' files. Remove them.
Also use the new flags in Makefile, to decide whether to compile
TLS-specific or IPSEC-specific objects, or not.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not directly call fpga version of IPsec function from main.c.
Wrap it by an accel version, and call the wrapper.
This will allow deprecating the FPGA IPsec stubs in downstream
patch.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series adds mlx5 support for devlink fw versions query.
1) Implement the required low level firmware commands
2) Implement the devlink knobs and callbacks for fw versions query.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl0eZOQACgkQSD+KveBX
+j6a0gf/SbSY2yDz6iyDZy7Zt0e7onD395UyWIoXbXJAI/aMggvdNE233dh369xa
d4Zo8zvFijiFpPKmP0p+WZfvR5YPPWgtOYDv1MbaTz5lqsGYUh2kN9FaTyCNZW3O
jeNidxjsne70VBrpmOZJX2mxduKwRdxchRg2iQPdeZQGO5Uq3nEdOfJVx/mhsIGw
iRczF4IAQpArZEyKXgqMSrtJ99FJ7JSJXnsqjVJyUC1zyCZ+Cq3VV55+u5VCBokd
qr/VSYqFd38SEHR5l4nXDXLX23pOwWNhUdPgGopjak8bN3k19vk6GfQ2bzLFnaOW
4fx1k4uTixKOrbLkgzay/YSsoF2TDw==
=Bwl7
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2019-07-04-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-update-2019-07-04
This series adds mlx5 support for devlink fw versions query.
1) Implement the required low level firmware commands
2) Implement the devlink knobs and callbacks for fw versions query.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For spinlocks the type spinlock_t should be used instead of "struct
spinlock".
Use spinlock_t for spinlock's definition.
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: oss-drivers@netronome.com
Cc: netdev@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Arnd,
We have to do a sync_single_for_device /somewhere/ before the
buffer is given to the device. On a non-cache-coherent machine with
a write-back cache, there may be dirty cache lines that get written back
after the device DMA's data into it (e.g. from a previous memset
from before the buffer got freed), so you absolutely need to flush any
dirty cache lines on it first.
Since the coherency is configurable in this device make sure we cover
all configurations by explicitly syncing the allocated buffer for the
device before refilling it's descriptors
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If HCLGE_MBX_MAX_RESP_DATA_SIZE > HCLGE_MBX_MAX_RESP_DATA_SIZE,
the memcpy will cause out of memory. So this patch just set
resp_data_len to the maximum length for this case.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some bitwise operator used signed type, this patch fixes
them with unsigned type.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds default value for tc_size and tc_offset, or it may
get random value and used later.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of msg_data may be NULL in some cases, which will cause
errors reported by some compiler.
So this patch adds a check to fix it.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of param type is always not changed in
hclgevf_bind_ring_to_vector, move the assignment to
front of "for {}" can reduce the redundant assignment.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the HNS3 driver just defines part of IMP return code,
This patch supplements all the remaining IMP return code, and adds
a function to convert this code to the error number.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver queries the media port information, and
updates the port capability periodically. But it sets an error
mac->speed_type value, which stops update port capability.
Fixes: 88d10bd6f7 ("net: hns3: add support for multiple media type")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control autoneg is unsupported for fibre port. It takes no
effect for flow control when restart autoneg. This patch fixes
it, return -EOPNOTSUPP when user tries to enable flow control
autoneg.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For revision 0x20, the broadcast promisc is enabled by firmware,
it's unnecessary to enable it when initializing VF.
For revision 0x21, it's necessary to enable broadcast promisc mode
when initializing or re-initializing VF, otherwise, it will be
unable to send and receive promisc packets.
Fixes: f01f5559ca ("net: hns3: don't allow vf to enable promisc mode")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply by filling the PTP shaper parameters array.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting port up down event (PUDE), change the PTP shaper
configuration based on hardware time stamping on/off and the port's
speed.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
