Logically, EFX_BUG_ON_PARANOID can never be correct. For, BUG_ON should
only be used if it is not possible to continue without potential harm;
and since the non-DEBUG driver will continue regardless (as the BUG_ON is
compiled out), clearly the BUG_ON cannot be needed in the DEBUG driver.
So, replace every EFX_BUG_ON_PARANOID with either an EFX_WARN_ON_PARANOID
or the newly defined EFX_WARN_ON_ONCE_PARANOID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's no longer used now that Falcon is gone.
Also remove a reference in a comment to an ioctl that doesn't exist.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Easy enough for Falcon users to enable it when making oldconfig.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defalconisation removed one of the string arguments, but missed the
corresponding %s.
Fixes: 5a6681e22c ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale: The differences between Falcon and Siena are in many ways larger
than those between Siena and EF10 (despite Siena being nominally "Falcon-
architecture"); for instance, Falcon has no MCPU, so there is no MCDI.
Removing Falcon support from the sfc driver should simplify the latter,
and avoid the possibility of Falcon support being broken by changes to sfc
(which are rarely if ever tested on Falcon, it being end-of-lifed hardware).
The sfc-falcon driver created in this changeset is essentially a copy of the
sfc driver, but with Siena- and EF10-specific code, including MCDI, removed
and with the "efx_" identifier prefix changed to "ef4_" (for "EFX 4000-
series") to avoid collisions when both drivers are built-in.
This changeset removes Falcon from the sfc driver's PCI ID table; then in
sfc I've removed obvious Falcon-related code: I removed the Falcon NIC
functions, Falcon PHY code, and EFX_REV_FALCON_*, then fixed up everything
that referenced them.
Also, increment minor version of both drivers (to 4.1).
For now, CONFIG_SFC selects CONFIG_SFC_FALCON, so that updating old configs
doesn't cause Falcon support to disappear; but that should be undone at
some point in the future.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use ->heap_buf after commit 46d1efd852 ("sfc: remove Software
TSO") so let's remove the last traces.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It gives no advantage over GSO now that xmit_more exists. If we find
ourselves unable to handle a TSO skb (because our TXQ doesn't have a
TSOv2 context and the NIC doesn't support TSOv1), hand it back to GSO.
Also do that if the TSO handler fails with EINVAL for any other reason.
As Falcon-architecture NICs don't support any firmware-assisted TSO,
they no longer advertise TSO feature flags at all.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to init the TXQ because of insufficient TSOv2 contexts,
try again with TSOv2 disabled.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for FATSOv2 to the driver. FATSOv2 offloads far more of the task
of TCP segmentation to the firmware, such that we now just pass a single
super-packet to the NIC. This means TSO has a great deal in common with a
normal DMA transmit, apart from adding a couple of option descriptors.
NIC-specific checks have been moved off the fast path and in to
initialisation where possible.
This also moves FATSOv1/SWTSO to a new file (tx_tso.c). The end of transmit
and some error handling is now outside TSO, since it is common with other
code.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi_hash_del() after netif_napi_del() is pointless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_copy_channel() doesn't correctly clear the napi_hash related state.
This means that when napi_hash_add is called for that channel nothing is
done, and we are left with a copy of the napi_hash_node from the old
channel. When we later call napi_hash_del() on this channel we have a
stale napi_hash_node.
Corruption is only seen when there are multiple entries in one of the
napi_hash lists. This is made more likely by having a very large number
of channels. Testing was carried out with 512 channels - 32 channels on
each of 16 ports.
This failure typically appears as protection faults within napi_by_id()
or napi_hash_add(). efx_copy_channel() is only used when tx or rx ring
sizes are changed (ethtool -G).
Fixes: 36763266bb ("sfc: Add support for busy polling")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves UDP spreading, and also slightly improves GRO performance
of encapsulated TCP on 7000 series NICs.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a NULL check before calling asynchronous MCDI completion functions
during device removal.
Fixes: 7014d7f6 ("sfc: allow asynchronous MCDI without completion function")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers must be ready to accept NULL from ptp_clock_register() if the
PTP clock subsystem is configured out.
This patch documents that and ensures that all drivers cope well
with a NULL return.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Eugenia Emantayev <eugenia@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Ma Yuying <yuma@redhat.com>
Suggested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC_CMD_TRIGGER_INTERRUPT does not work on the SFC9140, as used in the
sfn7x42q and sfn7x24f.
Check for this using the MCDI workaround mechanism.
The command is only used during self test. If it's not supported, skip
the interrupt test.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nic_data was already initialised to the right thing, no need to assign
it again.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX size bins were not supported on the 7000's 40G MAC, but the 8000 series
does support them and the MCPU advertises that via a new capability bit.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit systems, mask is only an array of 3 longs, not 4, so don't try
to write to mask[3].
Also include build-time checks in case the size of the bitmask changes.
Fixes: 3c36a2aded ("sfc: display vadaptor statistics for all interfaces")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The division is already being done properly in efx_ef10_get_timer_config
which returns zero-on-success, unlike the old efx_ef10_get_sysclk_freq.
Fixes: d95e329a55 ("sfc: get timer configuration from adapter")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SFN8000 series adapters the MC provides a method to get the timer
quantum and the maximum timer setting. We revert to the old values if the
new call is unavailable.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFN8000-series NICs require a new method of setting interrupt moderation,
via MCDI. This is indicated by a workaround flag. This new MCDI command
takes an explicit time value rather than a number of ticks. It therefore
makes sense to also store the moderation values in terms of time, since
that is what the ethtool interface is interested in.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than explicitly specifying flags we can now specify a desired
performance target to the firmware, ie higher throughput or lower latency.
For now we use the default "auto" configuration.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wextra, we get a harmless warning from the
EFX_EXTRACT_OWORD32 macro:
ethernet/sfc/farch.c: In function 'efx_farch_test_registers':
ethernet/sfc/farch.c:119:30: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:144: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:392: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:731: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
The macro and the caller are both correct, but we can avoid the
warning by changing the index variable to a signed type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vPort has VLAN_RESTRICT flag, VLAN tagged traffic will not be
delivered without corresponding Rx filters which may be proxied to and
moderated by hypervisor.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If should be done after net_dev->hw_features initialization, to keep the
feature there to be able to enable it later using ethtool.
VLAN filtering is enforced and fixed if vPort requires usage of VLAN
filters to receive tagged traffic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it is not supported we simply disable the feature.
For the feature to work we need firmware filter support for
OUTER_VID + LOC_MAC and for OUTER_VID + LOC_MAC_IG.
The low-latency firmware can match on OUTER_VID + LOC_MAC but not on
OUTER_VID + LOC_MAC_IG.
For the capture packet firmware it is the other way around.
Only the full-feature variant can match on both combinations.
Incorporates a fix by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
in the net_dev->[hw_]features handling.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filter match flags are not unique criteria to be mapped to priority
because of both unknown unicast and unknown multicast are mapped to
LOC_MAC_IG. So, local MAC is required to map filter to priority.
MCDI filter flags is unique criteria to find filter priority.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nearly every time we call efx_ef10_filter_remove_unsafe, we first check
for EFX_EF10_FILTER_ID_INVALID, in which case we do nothing. So move
that check into the function, simplifying all the call sites.
Also, change the return type to void, since none of the callers check it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to enslave an SFC interface to a bond the following BUG_ON was
hit:
kernel BUG [in ef10.c]!
CPU: 0 PID: 4383 Comm: ifenslave Tainted: G
...
Call Trace:
efx_ef10_filter_add_vlan+0x121/0x180 [sfc]
efx_ef10_filter_table_probe+0x2a2/0x4f0 [sfc]
efx_ef10_set_mac_address+0x370/0x6d0 [sfc]
efx_set_mac_address+0x7d/0x120 [sfc]
dev_set_mac_address+0x43/0xa0
bond_enslave+0x337/0xea0 [bonding]
This comes from function efx_ef10_filter_vlan_sync_rx_mode.
To solve the bug we ensure the mac_lock is taken before calling
efx_ef10_filter_add_vlan. But to avoid a priority inversion mac_lock must
be taken before filter_sem.
To satisfy these requirements we end up taking mac_lock in
efx_ef10_vport_set_mac_address, efx_ef10_set_mac_address,
efx_ef10_sriov_set_vf_vlan and efx_probe_filters.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supports HW VLAN filtering, en/disabled using ethtool.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now it contains dummy VLAN entry with unspecified VID only.
The entry is used for the case when HW VLAN filtering is not used.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags are built when address cache is updated.
The information will be required when VLAN filtering is added and address
cache is used without re-sync.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a step to support VLAN filtering in HW.
Until then, there is only one struct efx_ef10_filter_vlan per struct
efx_ef10_filter_table, with no VLAN information yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is required to remove setting of filter IDs to invalid from multicast
and unicast addresses caching functions.
Add initialization to invalid when filter table is created.
Add paranoid checks to track consistency.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
