In remove(), ensure that the PME work cannot run after kfree() is called.
Otherwise, this could result in a use-after-free.
This issue was detected with the help of Coccinelle.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Frederick Lawler <fred@fredlawl.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Dongdong reported a deadlock triggered by a hotplug event during a sysfs
"remove" operation:
pciehp 0000:00:0c.0:pcie004: Slot(0-1): Link Up
# echo 1 > 0000:00:0c.0/remove
PME and hotplug share an MSI/MSI-X vector. The sysfs "remove" side is:
remove_store
pci_stop_and_remove_bus_device_locked
pci_lock_rescan_remove
pci_stop_and_remove_bus_device
...
pcie_pme_remove
pcie_pme_suspend
synchronize_irq # wait for hotplug IRQ handler
pci_unlock_rescan_remove
The hotplug side is:
pciehp_ist
pciehp_handle_presence_or_link_change
pciehp_configure_device
pci_lock_rescan_remove # wait for pci_unlock_rescan_remove()
INFO: task bash:10913 blocked for more than 120 seconds.
# ps -ax |grep D
PID TTY STAT TIME COMMAND
10913 ttyAMA0 Ds+ 0:00 -bash
14022 ? D 0:00 [irq/745-pciehp]
# cat /proc/14022/stack
__switch_to+0x94/0xd8
pci_lock_rescan_remove+0x20/0x28
pciehp_configure_device+0x30/0x140
pciehp_handle_presence_or_link_change+0x324/0x458
pciehp_ist+0x1dc/0x1e0
# cat /proc/10913/stack
__switch_to+0x94/0xd8
synchronize_irq+0x8c/0xc0
pcie_pme_suspend+0xa4/0x118
pcie_pme_remove+0x20/0x40
pcie_port_remove_service+0x3c/0x58
...
pcie_port_device_remove+0x2c/0x48
pcie_portdrv_remove+0x68/0x78
pci_device_remove+0x48/0x120
...
pci_stop_bus_device+0x84/0xc0
pci_stop_and_remove_bus_device_locked+0x24/0x40
remove_store+0xa4/0xb8
dev_attr_store+0x44/0x60
sysfs_kf_write+0x58/0x80
It is incorrect to call pcie_pme_suspend() from pcie_pme_remove() for two
reasons.
First, pcie_pme_suspend() calls synchronize_irq(), which will wait for the
native hotplug interrupt handler as well as for the PME one, because they
share one IRQ (as per the spec). That may deadlock if hotplug is signaled
while pcie_pme_remove() is running and the latter calls
pci_lock_rescan_remove() before the former.
Second, if pcie_pme_suspend() figures out that wakeup needs to be enabled
for the port, it will return without disabling the interrupt as expected by
pcie_pme_remove() which was overlooked by commit c7b5a4e6e8 ("PCI / PM:
Fix native PME handling during system suspend/resume").
To fix that, rework pcie_pme_remove() to disable the PME interrupt, clear
its status and prevent the PME worker function from re-enabling it before
calling free_irq() on it, which should be sufficient.
Fixes: c7b5a4e6e8 ("PCI / PM: Fix native PME handling during system suspend/resume")
Link: https://lore.kernel.org/linux-pci/c7697e7c-e1af-13e4-8491-0a3996e6ab5d@huawei.com
Reported-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[bhelgaas: add URL and deadlock details from Dongdong]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously dpc_handler() called aer_get_device_error_info() without
initializing info->severity, so aer_get_device_error_info() relied on
uninitialized data.
Add dpc_get_aer_uncorrect_severity() to read the port's AER status, mask,
and severity registers and set info->severity.
Also, clear the port's AER fatal error status bits.
Fixes: 8aefa9b0d9 ("PCI/DPC: Print AER status in DPC event handling")
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Cc: stable@vger.kernel.org # v4.19+
The Class Code for subtractive decode PCI-to-PCI bridge is 060401h; add an
entry to make portdrv support this type of bridge. This allows use of PCIe
services on subtractive decode ports.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: add braces surrounding entry]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci_device_id table was technically correct, but unusually formatted,
which made adding entries error-prone. Change the format so it's obvious
how to add entries.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 0e157e5286.
Heiner reported that the commit in question prevents his network adapter
from triggering PME and waking up when network cable is plugged.
The commit tried to prevent root port waking up from D3cold immediately but
looks like disabing root port PME interrupt is not the right way to fix
that issue so revert it now. The patch following proposes an alternative
solution to that issue.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 0e157e5286 ("PCI/PME: Implement runtime PM callbacks")
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CC: stable@vger.kernel.org # v4.20+
match_string() returns the array index of a matching string. Use it
instead of the open-coded implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Expand Kconfig "PF" acronyms (Randy Dunlap)
- Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)
- Add missing include to drivers/pci.h (Alexandru Gagniuc)
- Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
instead of xhci (Thinh Nguyen)
* pci/misc:
PCI: Override Synopsys USB 3.x HAPS device class
PCI: Move Synopsys HAPS platform device IDs
PCI: Add missing include to drivers/pci.h
PCI: Remove unnecessary space before function pointer arguments
MAINTAINERS: Add x86 early-quirks.c file pattern to PCI subsystem
PCI: Expand the "PF" acronym in Kconfig help text
ASPM does not make use of the children or link LIST_HEADs declared in
struct pcie_link_state and defined in alloc_pcie_link_state(). Therefore,
remove these lists.
No functional change intended.
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ecae65e133 ("PCI/AER: Use kfifo_in_spinlocked() to insert locked
elements") replaced kfifo_put() with kfifo_in_spinlocked(), but passed the
*size* of the queue entry, where kfifo_in_spinlocked() expects the *number*
of entries to be copied.
We want to insert only one element into kfifo, not "sizeof(entry) = 16".
Without this patch, we would get 15 uninitialized elements.
Fixes: ecae65e133 ("PCI/AER: Use kfifo_in_spinlocked() to insert locked elements")
Signed-off-by: Yanjiang Jin <yanjiang.jin@hxt-semitech.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Make spacing more consistent in the code for function pointer declarations
based on checkpatch.pl.
Signed-off-by: Benjamin Young <youngcdev@gmail.com>
[bhelgaas: make similar changes in include/linux/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This reverts commit 17c9148736.
Rafael found that this commit broke the SD card reader in his
Acer Aspire S5. Details of the problem are in the bugzilla below.
Fixes: 17c9148736 ("PCI/ASPM: Do not initialize link state when aspm_disabled is set")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201801
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state (Keith
Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and re-enumerate
devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets (Keith
Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable from
cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments (Keith
Busch)
* pci/hotplug:
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI/AER: Use threaded IRQ for bottom half
PCI/AER: Use kfifo_in_spinlocked() to insert locked elements
PCI/AER: Use kfifo for tracking events instead of reimplementing it
PCI/AER: Remove error source from AER struct aer_rpc
PCI/AER: Remove unused aer_error_resume()
PCI: Uninline PCI bus accessors for better ftracing
PCI/AER: Remove pci_cleanup_aer_uncorrect_error_status() calls
PCI: pnv_php: Use kmemdup()
PCI: cpqphp: Remove set but not used variable 'physical_slot'
PCI/ERR: Remove duplicated include from err.c
PCI: Equalize hotplug memory and io for occupied and empty slots
PCI / ACPI: Whitelist D3 for more PCIe hotplug ports
ACPI / property: Allow multiple property compatible _DSD entries
PCI/PME: Implement runtime PM callbacks
PCI: pciehp: Implement runtime PM callbacks
PCI/portdrv: Add runtime PM hooks for port service drivers
PCI/portdrv: Resume upon exit from system suspend if left runtime suspended
PCI: pciehp: Do not handle events if interrupts are masked
PCI: pciehp: Disable hotplug interrupt during suspend
PCI / ACPI: Enable wake automatically for power managed bridges
PCI: Do not skip power-managed bridges in pci_enable_wake()
PCI: Make link active reporting detection generic
PCI: Unify device inaccessible
PCI/ERR: Always report current recovery status for udev
PCI/ERR: Simplify broadcast callouts
PCI/ERR: Run error recovery callbacks for all affected devices
PCI/ERR: Handle fatal error recovery
PCI/ERR: Use slot reset if available
PCI/AER: Don't read upstream ports below fatal errors
PCI/AER: Take reference on error devices
PCI/DPC: Save and restore config state
PCI: portdrv: Restore PCI config state on slot reset
PCI: portdrv: Initialize service drivers directly
PCI: hotplug: Document TODOs
PCI: hotplug: Embed hotplug_slot
PCI: hotplug: Drop hotplug_slot_info
PCI: hotplug: Constify hotplug_slot_ops
PCI: pciehp: Reshuffle controller struct for clarity
PCI: pciehp: Rename controller struct members for clarity
PCI: pciehp: Unify controller and slot structs
PCI: pciehp: Tolerate Presence Detect hardwired to zero
PCI: pciehp: Drop hotplug_slot_ops wrappers
PCI: pciehp: Drop unnecessary includes
PCI: pciehp: Differentiate between surprise and safe removal
PCI: Simplify disconnected marking
Move the bus ops fallback into separate functions. No functional change
here.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The aer_inject module was directly calling aer_irq(). This required the
AER driver export its private IRQ handler for no other reason than to
support error injection. A driver should not have to expose its private
interfaces, so use the IRQ subsystem to route injection to the AER driver,
and make aer_irq() a private interface.
This provides additional benefits:
First, directly calling the IRQ handler bypassed the IRQ subsytem so the
injection wasn't really synthesizing what happens if a shared AER interrupt
occurs.
The error injection had to provide the callback data directly, which may be
racing with a removal that is freeing that structure. The IRQ subsystem
can handle that race.
Finally, using the IRQ subsystem automatically reacts to threaded IRQs,
keeping the error injection abstracted from that implementation detail.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The port services driver already provides a method to find the pcie_device
for a service. Export that function, use it from the aer_inject module,
and remove the duplicate functionality.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the managed device resource allocations for the service data so the AER
driver doesn't need to manage it, further simplifying this driver.
Link: https://lore.kernel.org/linux-pci/20180918235848.26694-12-keith.busch@intel.com
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
'default n' is the default value for any bool or tristate Kconfig setting
so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO is not
set' for visible symbols") the Kconfig behavior is the same regardless of
'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The threaded IRQ is naturally single threaded as desired, so use that to
simplify the AER bottom half handler. Since the root port structure has
much less to do now, remove the rpc construction helper routine.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use the recommended kernel API for writing to a concurrently-accessed
kfifo. No functional change here.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The kernel provides a generic FIFO implementation, so no need to reinvent
that capability in a driver. Replace the AER-specific implementation with
the kernel-provided kfifo. Since the interrupt handler producer and work
queue consumer run single threaded, there is no need for additional
locking, so remove that lock, too.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The AER struct aer_rpc was carrying a copy of the error source simply as a
temperary variable. Remove that from the structure and use a stack
variable for the purpose.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The error recovery callbacks are only run on child devices. A Root Port is
never a child device, so this error resume callback was never invoked.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Basically we need to do the same steps than what we do when system sleep is
entered and disable PME interrupt when the root port is runtime suspended.
This prevents spurious wakeups immediately when the port is transitioned
into D3cold.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When PCIe port is runtime suspended/resumed some extra steps might be
needed to be executed from the port service driver side. For instance we
may need to disable PCIe hotplug interrupt to prevent it from triggering
immediately when PCIe link to the downstream component goes down.
To make the above possible add optional ->runtime_suspend() and
->runtime_resume() callbacks to struct pcie_port_service_driver and call
them for each port service in runtime suspend/resume callbacks of portdrv.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[bhelgaas: adjust "slot->state" for 5790a9c78e ("PCI: pciehp: Unify
controller and slot structs")]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently we try to keep PCIe ports runtime suspended over system suspend
if possible. This mostly happens when entering suspend-to-idle because
there is no need to re-configure wake settings.
This causes problems if the parent port goes into D3cold and it gets
resumed upon exit from system suspend. This may happen for example if the
port is part of PCIe switch and the same switch is connected to a PCIe
endpoint that needs to be resumed. The way exit from D3cold works according
PCIe 4.0 spec 5.3.1.4.2 is that power is restored and cold reset is
signaled. After this the device is in D0unitialized state keeping PME
context if it supports wake from D3cold.
The problem occurs when a PCIe hotplug port is left suspended and the
parent port goes into D3cold and back to D0: the port keeps its PME context
but since everything else is reset back to defaults (D0unitialized) it is
not set to detect hotplug events anymore.
For this reason change the PCIe portdrv power management logic so that it
is fine to keep the port runtime suspended over system suspend but it needs
to be resumed upon exit to make sure it gets properly re-initialized.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The spec has timing requirements when waiting for a link to become active
after a conventional reset. Implement those hard delays when waiting for
an active link so pciehp and dpc drivers don't need to duplicate this.
For devices that don't support data link layer active reporting, wait the
fixed time recommended by the PCIe spec.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Bring surprise removals and permanent failures together so we no longer
need separate flags. The implementation enforces that error handling will
not be able to override a surprise removal's permanent channel failure.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
A device still participates in error recovery even if it doesn't have
the error callbacks.
Always provide the status for user event watchers.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
There is no point in having a generic broadcast function if it needs to
have special cases for each callback it broadcasts.
Abstract the error broadcast to only the necessary information and removes
the now unnecessary helper to walk the bus.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
If an Endpoint reported an error with ERR_FATAL, we previously ran driver
error recovery callbacks only for the Endpoint's driver. But if we reset a
Link to recover from the error, all downstream components are affected,
including the Endpoint, any multi-function peers, and children of those
peers.
Initiate the Link reset from the deepest Downstream Port that is
reliable, and call the error recovery callbacks for all its children.
If a Downstream Port (including a Root Port) reports an error, we assume
the Port itself is reliable and we need to reset its downstream Link. In
all other cases (Switch Upstream Ports, Endpoints, Bridges, etc), we assume
the Link leading to the component needs to be reset, so we initiate the
reset at the parent Downstream Port.
This allows two other clean-ups. First, we currently only use a Link
reset, which can only be initiated using a Downstream Port, so we can
remove checks for Endpoints. Second, the Downstream Port where we initiate
the Link reset is reliable (unlike components downstream from it), so the
special cases for error detect and resume are no longer necessary.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
We don't need to be paranoid about the topology changing while handling an
error. If the device has changed in a hotplug capable slot, we can rely on
the presence detection handling to react to a changing topology.
Restore the fatal error handling behavior that existed before merging DPC
with AER with 7e9084b367 ("PCI/AER: Handle ERR_FATAL with removal and
re-enumeration of devices").
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The secondary bus reset may have link side effects that a hotplug capable
port may incorrectly react to. Use the slot specific reset for hotplug
ports, fixing the undesirable link down-up handling during error
recovering.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: fold in
https://lore.kernel.org/linux-pci/20180926152326.14821-1-keith.busch@intel.com
for issue reported by Stephen Rothwell <sfr@canb.auug.org.au>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The AER driver has never read the config space of an endpoint that reported
a fatal error because the link to that device is considered unreliable.
An ERR_FATAL from an upstream port almost certainly indicates an error on
its upstream link, so we can't expect to reliably read its config space for
the same reason.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Error handling may be running in parallel with a hot removal. Reference
count the device during AER handling so the device can not be freed while
AER wants to reference it.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
This patch provides DPC save and restore capabilities. This is necessary
for the driver to observe DPC events in the event the configuration space
needs to be restored after a reset.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The port's config space may be cleared after a link reset, which wipes out
the bridge's bus and memory windows. Restore the config space that was
saved during probe so we can access downstream devices.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
The PCI port driver saves the PCI state after initializing the device with
the applicable service devices. This was, however, before the service
drivers were even registered because PCI probe happens before the
device_initcall initialized those service drivers. The config space state
that the services set up were not being saved. The end result would cause
PCI devices to not react to events that the drivers think they did if the
PCI state ever needed to be restored.
Fix this by changing the service drivers from using the init calls to
having the portdrv driver calling the services directly. This will get the
state saved as desired, while making the relationship between the port
driver and the services under it more explicit in the code.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Now that ASPM is configured for *all* PCIe devices at boot, a problem is
seen with systems that set the FADT NO_ASPM bit. This bit indicates that
the OS should not alter the ASPM state, but when
pcie_aspm_init_link_state() runs it only checks for !aspm_support_enabled.
This misses the ACPI_FADT_NO_ASPM case because that is setting
aspm_disabled.
The result is systems may hang at boot after 1302fcf; avoidable if they
boot with pcie_aspm=off (sets !aspm_support_enabled).
Fix this by having aspm_init_link_state() check for either
!aspm_support_enabled or acpm_disabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201001
Fixes: 1302fcf0d0 ("PCI: Configure *all* devices, not just hot-added ones")
Signed-off-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 89ee9f7680 ("PCI: Add device disconnected state") iterates over
the devices on a parent bus, marks each as disconnected, then marks
each device's children as disconnected using pci_walk_bus().
The same can be achieved more succinctly by calling pci_walk_bus() on
the parent bus. Moreover, this does not need to wait until acquiring
pci_lock_rescan_remove(), so move it out of that critical section.
The critical section in err.c contains a pci_dev_get() / pci_dev_put()
pair which was apparently copy-pasted from pciehp_pci.c. In the latter
it serves the purpose of holding the struct pci_dev in place until the
Command register is updated. err.c doesn't do anything like that, hence
the pair is unnecessary. Remove it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Oza Pawandeep <poza@codeaurora.org>
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Upon removal of the last device on a bus, the link_state of the bridge
leading to that bus is sought to be torn down by having pci_stop_dev()
call pcie_aspm_exit_link_state().
When ASPM was originally introduced by commit 7d715a6c1a ("PCI: add
PCI Express ASPM support"), it determined whether the device being
removed is the last one by calling list_empty() on the bridge's
subordinate devices list. That didn't work because the device is only
removed from the list slightly later in pci_destroy_dev().
Commit 3419c75e15 ("PCI: properly clean up ASPM link state on device
remove") attempted to fix it by calling list_is_last(), but that's not
correct either because it checks whether the device is at the *end* of
the list, not whether it's the last one *left* in the list. If the user
removes the device which happens to be at the end of the list via sysfs
but other devices are preceding the device in the list, the link_state
is torn down prematurely.
The real fix is to move the invocation of pcie_aspm_exit_link_state() to
pci_destroy_dev() and reinstate the call to list_empty(). Remove a
duplicate check for dev->bus->self because pcie_aspm_exit_link_state()
already contains an identical check.
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: stable@vger.kernel.org # v2.6.26
- To avoid bus errors, enable PASID only if entire path supports End-End
TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD Controller
(Bjorn Helgaas)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: Rename pci_try_reset_bus() to pci_reset_bus()
PCI: Deprecate pci_reset_bus() and pci_reset_slot() functions
PCI: Unify try slot and bus reset API
PCI: Hide pci_reset_bridge_secondary_bus() from drivers
IB/hfi1: Use pci_try_reset_bus() for initiating PCI Secondary Bus Reset
PCI: Handle error return from pci_reset_bridge_secondary_bus()
PCI/IOV: Tidy pci_sriov_set_totalvfs()
PCI: Enable PASID only if entire path supports End-End TLP prefixes
# Conflicts:
# drivers/pci/hotplug/pciehp_hpc.c
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
* pci/dpc:
PCI/DPC: Remove indirection waiting for inactive link
PCI/DPC: Use threaded IRQ for bottom half handling
PCI/DPC: Print AER status in DPC event handling
PCI/DPC: Remove rp_pio_status from dpc struct
PCI/DPC: Defer event handling to work queue
PCI/DPC: Leave interrupts enabled while handling event
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
* pci/aspm:
PCI: Remove unnecessary include of <linux/pci-aspm.h>
iwlwifi: Remove unnecessary include of <linux/pci-aspm.h>
ath9k: Remove unnecessary include of <linux/pci-aspm.h>
igb: Remove unnecessary include of <linux/pci-aspm.h>
PCI/ASPM: Convert to use sysfs_match_string() helper
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
* pci/aer:
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI/AER: Remove duplicate PCI_EXP_AER_FLAGS definition
PCI/portdrv: Remove pcie_portdrv_err_handler.slot_reset
PCI/AER: Clear device status bits during ERR_COR handling
PCI/AER: Clear device status bits during ERR_FATAL and ERR_NONFATAL
PCI/AER: Remove ERR_FATAL code from ERR_NONFATAL path
PCI/AER: Factor out ERR_NONFATAL status bit clearing
PCI/AER: Clear only ERR_NONFATAL bits during non-fatal recovery
PCI/AER: Clear only ERR_FATAL status bits during fatal recovery
PCI/AER: Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST
PCI/AER: Add sysfs attributes for rootport cumulative stats
PCI/AER: Add sysfs attributes to provide AER stats and breakdown
PCI/AER: Define aer_stats structure for AER capable devices
PCI/AER: Move internal declarations to drivers/pci/pci.h
PCI/AER: Adopt lspci names for AER error decoding
PCI/AER: Expose internal API for obtaining AER information
# Conflicts:
# drivers/pci/pci.h
If the platform requests Firmware-First error handling, firmware is
responsible for reading and clearing AER status bits. If OSPM also clears
them, we may miss errors. See ACPI v6.2, sec 18.3.2.5 and 18.4.
This race is mostly of theoretical significance, as it is not easy to
reasonably demonstrate it in testing.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: add similar guards to pci_cleanup_aer_uncorrect_error_status()
and pci_aer_clear_fatal_status()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sysfs_match_string() helper returns index of the matching string in an
array. Use it in pcie_aspm_set_policy() to simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bhelgaas: squash sysfs_match_string() fix into original patch for issue
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI_EXP_AER_FLAGS was defined twice (with identical definitions), once
under #ifdef CONFIG_ACPI_APEI, and again at the top level. This looks like
my merge error from these commits:
fd3362cb73 ("PCI/AER: Squash aerdrv_core.c into aerdrv.c")
41cbc9eb1a ("PCI/AER: Squash ecrc.c into aerdrv.c")
Remove the duplicate PCI_EXP_AER_FLAGS definition.
Fixes: 41cbc9eb1a ("PCI/AER: Squash ecrc.c into aerdrv.c")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Thunderbolt hotplug ports that were occupied before system sleep resume
with their downstream link in "off" state. Only after the Thunderbolt
controller has reestablished the PCIe tunnels does the link go up.
As a result, a spurious Presence Detect Changed and/or Data Link Layer
State Changed event occurs.
The events are not immediately acted upon because tunnel reestablishment
happens in the ->resume_noirq phase, when interrupts are still disabled.
Also, notification of events may initially be disabled in the Slot
Control register when coming out of system sleep and is reenabled in the
->resume_noirq phase through:
pci_pm_resume_noirq()
pci_pm_default_resume_early()
pci_restore_state()
pci_restore_pcie_state()
It is not guaranteed that the events are acted upon at all: PCIe r4.0,
sec 6.7.3.4 says that "a port may optionally send an MSI when there are
hot-plug events that occur while interrupt generation is disabled, and
interrupt generation is subsequently enabled." Note the "optionally".
If an MSI is sent, pciehp will gratuitously turn the slot off and back
on once the ->resume_early phase has commenced.
If an MSI is not sent, the extant, unacknowledged events in the Slot
Status register will prevent future notification of presence or link
changes.
Commit 13c65840fe ("PCI: pciehp: Clear Presence Detect and Data Link
Layer Status Changed on resume") fixed the latter by clearing the events
in the ->resume phase. Move this to the ->resume_noirq phase to also
fix the gratuitous disable/enablement of the slot.
The commit further restored the Slot Control register in the ->resume
phase, but that's dispensable because as shown above it's already been
done in the ->resume_noirq phase.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Replace suspend_iter() and resume_iter() with a single function pm_iter()
to allow addition of port service callbacks for further power management
phases without having to add another iterator each time.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When an fatal error is received by a non-bridge device, the device is
removed, and pci_stop_and_remove_bus_device() deallocates the device
structure. The freed device structure is used by subsequent code to send
uevents and print messages.
Hold a reference on the device until we're finished using it. This is not
an ideal fix because pcie_do_fatal_recovery() should not use the device at
all after removing it, but that's too big a project for right now.
Fixes: 7e9084b367 ("PCI/AER: Handle ERR_FATAL with removal and re-enumeration of devices")
Signed-off-by: Thomas Tai <thomas.tai@oracle.com>
[bhelgaas: changelog, reduce get/put coverage]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci_error_handlers.slot_reset() callback is only used for non-bridge
devices (see broadcast_error_message()). Since portdrv only binds to
bridges, we don't need pcie_portdrv_slot_reset(), so remove it.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove pcie_portdrv_slot_reset() completely]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In case of correctable error, the Correctable Error Detected bit in the
Device Status register is set. Clear it after handling the error.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Clear the device status bits while handling both ERR_FATAL and ERR_NONFATAL
cases.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: rename to pci_aer_clear_device_status(), declare internal to PCI
core instead of exposing it everywhere]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
broadcast_error_message() is only used for ERR_NONFATAL events, when the
state is always pci_channel_io_normal, so remove the unused alternate path.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
aer_error_resume() clears all ERR_NONFATAL error status bits. This is
exactly what pci_cleanup_aer_uncorrect_error_status(), so use that instead
of duplicating the code.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_cleanup_aer_uncorrect_error_status() is called by driver .slot_reset()
methods when handling ERR_NONFATAL errors. Previously this cleared *all*
the bits, including ERR_FATAL bits.
Since we're only handling ERR_NONFATAL errors, clear only the ERR_NONFATAL
error status bits.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
During recovery from fatal errors, we previously called
pci_cleanup_aer_uncorrect_error_status(), which cleared *all* uncorrectable
error status bits (both ERR_FATAL and ERR_NONFATAL).
Instead, call a new pci_aer_clear_fatal_status() that clears only the
ERR_FATAL bits (as indicated by the PCI_ERR_UNCOR_SEVER register).
Based-on-patch-by: Oza Pawandeep <poza@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rename pci_reset_bridge_secondary_bus() to pci_bridge_secondary_bus_reset()
and move the declaration from linux/pci.h to drivers/pci.h to be used
internally in PCI directory only.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit 01fd61c0b9 ("PCI: Add a return type for
pci_reset_bridge_secondary_bus()") added a return value to the function to
return if a device is accessible following a reset. Callers are not
checking the value.
Pass error code up high in the stack if device is not accessible.
Fixes: 01fd61c0b9 ("PCI: Add a return type for pci_reset_bridge_secondary_bus()")
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Simplify waiting for the contained link to become inactive, removing the
indirection to a unnecessary DPC-specific handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Remove the work struct that was being used to handle a DPC event and use a
threaded IRQ instead.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
A DPC enabled device suppresses ERR_(NON)FATAL messages, preventing the AER
handler from reporting error details. If the DPC trigger reason says the
downstream port detected the error, collect the AER uncorrectable status
for logging, then clear the status.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
We don't need to save the rp pio status across multiple contexts as all
DPC event handling occurs in a single work queue context.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Move all event handling to the existing work queue, which will
make it simpler to pass event information to the handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Now that the DPC driver clears the interrupt status before exiting the
IRQ handler, we don't need to abuse the DPC control register to know if
a shared interrupt is for a new DPC event: a DPC port can not trigger
a second interrupt until the host clears the trigger status later in the
work queue handler.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
According to the documentation, "pcie_ports=native", linux should use
native AER and DPC services. While that is true for the _OSC method
parsing, this is not the only place that is checked. Should the HEST
list PCIe ports as firmware-first, linux will not use native services.
This happens because aer_acpi_firmware_first() doesn't take 'pcie_ports'
into account. This is wrong. DPC uses the same logic when it decides
whether to load or not, so fixing this also fixes DPC not loading.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: return "false" from bool function (from kbuild robot)]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes for rootport statistics (that are cumulative of all
the ERR_* messages seen on this PCI hierarchy).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes to provide total and breakdown of the AERs seen,
into different type of correctable, fatal and nonfatal errors:
/sys/bus/pci/devices/<dev>/aer_dev_correctable
/sys/bus/pci/devices/<dev>/aer_dev_fatal
/sys/bus/pci/devices/<dev>/aer_dev_nonfatal
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Define a structure to hold the AER statistics. There are 2 groups of
statistics: dev_* counters that are to be collected for all AER capable
devices and rootport_* counters that are collected for all (AER capable)
rootports only. Allocate and free this structure when device is added or
released (thus counters survive the lifetime of the device).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since pci_aer_init() and pci_no_aer() are used only internally, move their
declarations to the PCI internal header file. Also, no one cares about
return value of pci_aer_init(), so make it void.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
lspci uses abbreviated naming for AER error strings. Adopt the same naming
convention for the AER printing so they match.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Export some common AER functions and structures for other PCI core drivers
to use. Since this is making the function externally visible inside the
PCI core, prepend "aer_" to the function name.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: move AER declarations from linux/aer.h to drivers/pci/pci.h]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Use "PCI Express" consistently in Kconfig text. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Hoist aerdrv.c, aer_inject.c up to drivers/pci/pcie/ so they're next to
other PCIe service drivers. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Most of the things in aerdrv.h are only used in aerdrv.c, so move them
there. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
The aer_irq() declaration is the only thing needed by aer_inject.c. Move
it to portdrv.h so we eventually get rid of aerdrv.h completely. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Move pcie_aer_get_firmware_first() to portdrv.h, where it can be more
easily shared between AER and DPC. Then DPC no longer needs to include
aer/aerdrv.h. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
pcie_port_bus_type is already declared in portdrv.h, so remove the
unnecessary duplicate declaration in aerdrv.h. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reorder code to group probe/remove stuff together. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <keith.busch@intel.com>
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use ACPI
hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
* pci/hotplug:
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: shpchp: Use dev_printk() for OSHP-related messages
PCI: shpchp: Remove get_hp_hw_control_from_firmware() wrapper
PCI: shpchp: Remove acpi_get_hp_hw_control_from_firmware() flags
PCI: shpchp: Rely on previous _OSC results
PCI: shpchp: Request SHPC control via _OSC when adding host bridge
PCI: shpchp: Convert SHPC to be builtin only
PCI: pciehp: Make pciehp_is_native() stricter
PCI: pciehp: Rename host->native_hotplug to host->native_pcie_hotplug
PCI: pciehp: Request control of native hotplug only if supported
PCI: pciehp: Clear Presence Detect and Data Link Layer Status Changed on resume
PCI: pnv_php: Add missing of_node_put()
PCI: pciehp: Add quirk for Command Completed errata
PCI: Add Qualcomm vendor ID
PCI: ibmphp: Fix use-before-set in get_max_bus_speed()
# Conflicts:
# drivers/acpi/pci_root.c
- disable ASPM L1.2 substate if we don't have LTR (Bjorn Helgaas)
- respect platform ownership of LTR (Bjorn Helgaas)
* pci/aspm:
PCI/ACPI: Request LTR control from platform before using it
PCI/ASPM: Disable ASPM L1.2 Substate if we don't have LTR
The AER driver only needed the pcie_device to get to the port pci_dev.
Save the pci_dev pointer directly in struct aer_rpc and remove the
unnecessary indirection.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Decode the Requester ID from the AER Error Source Register into domain/
bus/device/function format to match other logging. In cases where the ID
matches the device used for pci_err(), drop the extra ID completely so we
don't print it twice.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Just move the actual function up so that it is visible to its user
aer_recover_queue().
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Our goal is to handle ERR_FATAL errors similarly, whether they are reported
via AER or via DPC. A previous commit changed AER so it handles ERR_FATAL
by calling driver .remove() methods and resetting the Link. DPC already
does that (although the Link reset is done automatically by hardware and
happens before we call the driver .remove() methods).
Restructure the DPC code so it calls the same pcie_do_fatal_recovery()
interface used by AER. This makes it clearer that we want to use the same
path.
Implement the .reset_link() method used by pcie_do_fatal_recovery(). For
DPC, the actual reset is done automatically by hardware, so we really only
have to wait for the Link to be inactive, then release the Port from DPC.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, DPC_FATAL is not a bitfield, can be sequential]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pass the service type to pcie_do_fatal_recovery() instead of assuming AER.
We will make DPC also use pcie_do_fatal_recovery(), and it needs to do
things a little differently for AER and DPC.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: split to separate patch]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
