There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register. Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus drive
to continue without problems if one of them fails.
This patch splits the ADAV80X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register? Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus allows the registration of the other bus driver
to continue without problems if one of them fails.
This patch splits the ssm2602 driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
While we are at it also cleanup the include section of the ssm2602 driver and
remove unneeded includes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register? Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus driver
to continue without problems if one of them fails.
This patch splits the AD193X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since the machine driver selects the CODEC driver we need to make sure that the
machine driver is only selectable if the CODEC driver can be build. This avoids
build errors under some configurations (which typically only result from
randconfig).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ASoC core assumes that the PCM component of the ASoC card transparently
moves data around and does not impose any restrictions on the memory layout or
the transfer speed. It ignores all fields from the snd_pcm_hardware struct for
the PCM driver that are related to this. Setting these fields in the PCM driver
might suggest otherwise though, so rather not set them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Two peaks in diffstat are for the audio EQ init of IDT codecs and the
EMU2004 usb mixer addition, both of which are pretty device-specific,
so safe to apply. The rest are a bunch of small fixes, most of them
are regression fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJSh0+UAAoJEGwxgFQ9KSmkFpcQAK8+FlQyzjkUD8SAd9xINjm1
gC7b8cIldx9+LLDvKCshcqM8+RID3EhtUz5DgDmpG7LnJy30aYjhc1McGMiBXLE1
Lwxi5oM8Rka5OSeW1J98gApeS1QxKRRCjE/6X3Vnnzymy4YziBEf1E6u3o2ZqPiM
jCLe3nuElrGKrfzoYIf4uI+oA2+iDzc29f/gFV0wl0TXBbuNwNgapfZjeDpyTM49
D9nhZ5bKddwxo8wgqySqfSrHU37tquNTTayTvD31Q9AQQzXWgTnv4uDpXACTY5h8
ynYEvkaOD3jMmjTLHU2ygVRKu1ydl+FV6I9JQGvaJbLl/KCGIW3IRQYowH/NltUu
U/PmYuEOYL5tXNkkO1lN49Ohj2dmgmfO8I1cSUjPyKdNuFEE/AuTIFuSogKittgV
vuQwyKhZ3sp8g1cQ5YbxSVJI7O+NyFd/XzeL6mIxnBIa6tf2NIIWVkvCFuEmrnKp
nsVf+JV8wr2tCRHWXRpW9wdLCt5XvKfwXfMZxUKLkxdZMKWy4qwh5ROEs+Tap4D+
dMThpWDOpC5H92Ygei5dpFav2dL+Iq8+QzLwzgN+JFvtNVUfqKTo7a+jbRdQhoec
w3DDxhS3MUwpenwiCX9M61RZZhQFNSn1t6J+wA5MCAnOfco71nkN1gf45iry3Vww
j9zeFh22uHWN0ttyF5zl
=lXBM
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Two peaks in diffstat are for the audio EQ init of IDT codecs and the
EMU2004 usb mixer addition, both of which are pretty device-specific,
so safe to apply. The rest are a bunch of small fixes, most of them
are regression fixes"
* tag 'sound-fix-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (26 commits)
ALSA: hda - load EQ params into IDT codec on HP bNB13 systems
ASoC: cs42l52: Correct MIC CTL mask
ASoC: wm8962: Turn on regcache_cache_only before disabling regulator
ALSA: jack: Unregister input device at disconnection
ALSA: pcsp: Fix the order of input device unregistration
ASoC: fsl: imx-pcm-fiq: omit fiq counter to avoid harm in unbalanced situations
ASoC: blackfin: Fix missing break
ALSA: usb-audio: add front jack channel selector for EMU0204
ALSA: hda - Don't clear the power state at snd_hda_codec_reset()
ASoC: arizona: Fix typo in name of EQ coefficient controls
ALSA: hda - Control EAPD for Master volume on Lenovo N100
ALSA: hda - Don't turn off EAPD for headphone on Lenovo N100
ALSA: isa: not allocating enough space
ALSA: snd-aoa: two copy and paste bugs
ASoC: wm8997: Correct typo in ISRC mux routes
ALSA: hda - Check keep_eapd_on before inv_eapd
ALSA: hda - Fix Line Out automute on Realtek multifunction jacks
ALSA: msnd: Avoid duplicated driver name
ALSA: compress_core: don't return -EBADFD from poll if paused
ALSA: hda - hdmi: Fix wrong baseline length in ATI/AMD generated ELD
...
A few fixes in drivers, the i.MX and wm8962 fixes are for a pretty nasty
issues for users of those drivers if they run into them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=qcIh
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.13
A few fixes in drivers, the i.MX and wm8962 fixes are for a pretty nasty
issues for users of those drivers if they run into them.
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
This code sequence is unsafe in modules:
static u64 mask = DMA_BIT_MASK(something);
...
if (!dev->dma_mask)
dev->dma_mask = &mask;
as if a module is reloaded, the mask will be pointing at the original
module's mask address, and this can lead to oopses. Moreover, they
all follow this with:
if (!dev->coherent_dma_mask)
dev->coherent_dma_mask = mask;
where 'mask' is the same value as the statically defined mask, and this
bypasses the architecture's check on whether the DMA mask is possible.
Fix these issues by using the new dma_coerce_coherent_and_mask()
function.
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SNDRV_PCM_FORMAT_S8 isn't supposed to fall through to SNDRV_PCM_FORMAT_S16_LE
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The blackfin ac97 driver never defines nor uses a global ac97 struct. So remove
the extern declaration for it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
If CONFIG_SND_BF5XX_HAVE_COLD_RESET is enabled building the blackfin ac97 driver
fails with the following compile error:
sound/soc/blackfin/bf5xx-ac97.c: In function ‘asoc_bfin_ac97_probe’:
sound/soc/blackfin/bf5xx-ac97.c:297: error: expected ‘;’ before ‘{’ token
sound/soc/blackfin/bf5xx-ac97.c:302: error: label ‘gpio_err’ used but not defined
The issue was introduced in commit 6dab2fd7 ("ASoC: bf5xx-ac97: Convert to
devm_gpio_request_one()").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
As part of the multiplatform refactoring for AC'97 the AC'97 bus ops were
staticised meaning that the prototype (which was never needed) conflicts
with the declaration causing build failures.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Some more fixes and enhancements, and also a bunch of refectoring for
AC'97 support which enables more than one AC'97 controller driver to be
built in.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=UZaY
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More updates for v3.11
Some more fixes and enhancements, and also a bunch of refectoring for
AC'97 support which enables more than one AC'97 controller driver to be
built in.
Currently we can only have a single platform built in with AC'97 support
due to the use of a global variable to provide the bus operations. Fix
this by making that variable a pointer and having the bus drivers set the
operations prior to registering.
This is not a particularly good or nice approach but it avoids blocking
multiplatform and a real fix involves fixing the fairly deep problems
with AC'97 support - we should be converting it to a real bus.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that the bf5xx-i2s driver supports TDM mode and all users of the bf5xx-tdm
driver have been switch over to using the bf5xx-i2s driver there is no need to
keep the b5fxx-tdm driver around.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s driver now has support for TDM mode and the bf5xx-tdm driver is
going to be removed soon, so switch the driver over to bf5xx-i2s.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s driver now has support for TDM mode and the bf5xx-tdm driver is
going to be removed soon, so switch the driver over to bf5xx-i2s.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx-i2s{,-pcm} and bf5xx-tdm{-pcm} drivers are nearly identical. Both are
for the same hardware each supporting a slight different subset of the hardware.
The bf5xx-i2s driver supports 2 channel I2S mode while the bf5xx-tdm driver
supports TDM mode and channel remapping. This patch adds support for TDM mode
and channel remapping to the bf5xx-i2s driver so that we'll eventually be able
to retire the bf5xx-tdm driver. Unfortunately the hardware is fixed to using 8
channels in TDM mode. The bf5xx-tdm driver jumps through a few hoops to make it
work well with other channel counts as well:
* Don't support mmap
* Translate between internal frame size (which is always 8 * sample_size)
and ALSA frame size (which depends on the channel count)
* Have special copy and silence callbacks which are aware of the mismatch
between internal and ALSA frame size
* Reduce the maximum buffer size to ensure that there is enough headroom for
dummy data.
The bf5xx-i2s driver is going to use the same mechanisms when being used int
TDM mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_pcm_lib_preallocate_pages_for_all() for pre-allocating the DMA buffers
instead of re-implementing the same functionality. Note that there is no need
to call snd_pcm_lib_free_pages_for_all() since the ALSA core takes care of this
for us.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to always allocate the maximum buffer size. While we are at it
also pass errors returned by snd_pcm_lib_malloc_pages() on to the upper layers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the hardware supports it there is no need to artificially limit this to
just being able to set the same mask for both tx and rx.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using dev_{err,dbg} instead of pr_{error,debug} makes it easier to recognize
which device created the message.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The structs defined in these files are completely unused, so remove both the
structs and the files.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bf5xx_tdm_pcm_ops struct is only used in bf5xx-tdm-pcm.c, so make it static.
Cc: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cpu dai and codec name are passed in through platform data.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver enables i2s mode support on blackfin bf6xx platform.
We reuse bf5xx-i2s-pcm.c as its i2s pcm driver because it's the same
for both bf5xx and bf6xx soc.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SPORT(Serial Port) module on bf6xx soc has a totally different ip
comparing to bf5xx soc. An individual SPORT module consists of two
independently configurable SPORT halves with identical functionality.
Each SPORT half can be configured for either transmitter or receiver.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The sysclock is fixed, so just set it up once in the init callback instead of
setting it repeatably in the hw_params callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 980b0bc69 ("ASoC: blackfin: Use dai_fmt") converted the blackfin ASoC
machine drivers to use the dai_links dai_fmt field to setup their DAI format.
For the bf5xx-ssm2602 the commit removed the manual call to snd_soc_dai_set_fmt,
but missed to set the dai_links dai_fmt field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the dai_link's dai_fmt attribute to setup the DAI format instead of doing
this manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a follow up on 53dea36c70 which fixes the other affected
pcm engines.
Description from 53dea36c70:
Don't rely on the codec's channels_min information to decide wheter or
not allocate a substream's DMA buffer. Rather check if the substream
itself was allocated previously.
Without this patch I was seeing null-pointer dereferenc in atmel-pcm.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Missed .owner of struct snd_soc_card will prevent the module from being
removed from underneath its users.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Factor out some boilerplate code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
