Igor Russkikh says:
====================
Aquantia atlantic hot fixes 03-2018
This is a set of atlantic driver hot fixes for various areas:
Some issues with hardware reset covered,
Fixed napi_poll flood happening on some traffic conditions,
Allow system to change MAC address on live device,
Add pci shutdown handler.
patch v2:
- reverse christmas tree
- remove driver private parameter, replacing it with define.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should close link and all NIC operations during shutdown.
On some systems graceful reboot never closes NIC interface on its own,
but only indicates pci device shutdown. Without explicit handler, NIC
rx rings continued to transfer DMA data into prepared buffers while CPU
rebooted already. That caused memory corruptions on soft reboot.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing prevents us from changing MAC on the running interface.
Allow this with ndev priv flag.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should report to napi full budget only when we have more job to do.
Before this fix, on any tx queue cleanup we forced napi to do poll again.
Thats a waste of cpu resources and caused storming with napi polls when
there was at least one tx on each interrupt.
With this fix we report full budget only when there is more job on TX
to do. Or, as before, when rx budget was fully consumed.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
B1 hardware changes behavior of mailbox interface, it has busy bit
always raised. Data ready condition should be detected by increment
of address register.
Old code has empty `for` loop, and that caused cpu overloads on B1
hardware. aq_nic_service_timer_cb consumed ~100ms because of that.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW 1.5.58 and below needs a fixed delay even after 0x18 register
is filled. Otherwise, setting MPI_INIT state too fast causes
traffic hang.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under some circumstances (notably using thunderbolt interface) SPI
on chip reset may be in active transaction.
Here we forcibly cleanup SPI to prevent possible hangups.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-03-20
Please apply one final set of qeth patches for 4.16.
All of these fix long-standing bugs, so please queue them up for -stable
as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the IRQ handler determines that one of the cmd IO channels has
failed and schedules recovery, block any further cmd requests from
being submitted. The request would inevitably stall, and prevent the
recovery from making progress until the request times out.
This sort of error was observed after Live Guest Relocation, where
the pending IO on the READ channel intentionally gets terminated to
kick-start recovery. Simultaneously the guest executed SIOCETHTOOL,
triggering qeth to issue a QUERY CARD INFO command. The command
then stalled in the inoperabel WRITE channel.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For calling ccw_device_start(), issue_next_read() needs to hold the
device's ccwlock.
This is satisfied for the IRQ handler path (where qeth_irq() gets called
under the ccwlock), but we need explicit locking for the initial call by
the MPC initialization.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth_wait_for_threads() is potentially called by multiple users, make
sure to notify all of them after qeth_clear_thread_running_bit()
adjusted the thread_running_mask. With no timeout, callers would
otherwise stall.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On removal, a qeth card's netdevice is currently not properly freed
because the call chain looks as follows:
qeth_core_remove_device(card)
lx_remove_device(card)
unregister_netdev(card->dev)
card->dev = NULL !!!
qeth_core_free_card(card)
if (card->dev) !!!
free_netdev(card->dev)
Fix it by free'ing the netdev straight after unregistering. This also
fixes the sysfs-driven layer switch case (qeth_dev_layer2_store()),
where the need to free the current netdevice was not considered at all.
Note that free_netdev() takes care of the netif_napi_del() for us too.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kevin Hao says:
====================
net: phy: Add general dummy stubs for MMD register access
v2:
As suggested by Andrew:
- Add general dummy stubs
- Also use that for the micrel phy
This patch series fix the Ethernet broken on the mpc8315erdb board introduced
by commit b6b5e8a691 ("gianfar: Disable EEE autoneg by default").
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new general dummy stubs for MMD register access were introduced.
Use that for the codes reuse.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet on mpc8315erdb is broken since commit b6b5e8a691
("gianfar: Disable EEE autoneg by default"). The reason is that
even though the rtl8211b doesn't support the MMD extended registers
access, it does return some random values if we trying to access
the MMD register via indirect method. This makes it seem that the
EEE is supported by this phy device. And the subsequent writing to
the MMD registers does cause the phy malfunction. So use the dummy
stubs for the MMD register access to fix this issue.
Fixes: b6b5e8a691 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some phy devices, even though they don't support the MMD extended
register access, it does have some side effect if we are trying to
read/write the MMD registers via indirect method. So introduce general
dummy stubs for MMD register access which these devices can use to avoid
such side effect.
Fixes: b6b5e8a691 ("gianfar: Disable EEE autoneg by default")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix possible IPv6 packet loss when multicast extension is used, by Linus Luessing
- fix SKB handling issues for TTVN and DAT, by Matthias Schiffer (two patches)
- fix include for eventpoll, by Sven Eckelmann
- fix skb checksum for ttvn reroutes, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=hsM8
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20180319' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- fix possible IPv6 packet loss when multicast extension is used, by Linus Luessing
- fix SKB handling issues for TTVN and DAT, by Matthias Schiffer (two patches)
- fix include for eventpoll, by Sven Eckelmann
- fix skb checksum for ttvn reroutes, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The clockid argument of clockid_to_kclock() comes straight from user space
via various syscalls and is used as index into the posix_clocks array.
Protect it against spectre v1 array out of bounds speculation. Remove the
redundant check for !posix_clock[id] as this is another source for
speculation and does not provide any advantage over the return
posix_clock[id] path which returns NULL in that case anyway.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1802151718320.1296@nanos.tec.linutronix.de
DRM_VMW_EVENT_FENCE_SIGNALED (struct drm_vmw_event_fence) and
DRM_EVENT_VBLANK (struct drm_event_vblank) pass timestamps in 32-bit
seconds/microseconds format.
As of commit c61eef726a ("drm: add support for monotonic vblank
timestamps"), other DRM drivers use monotonic times for drm_event_vblank,
but vmwgfx still uses CLOCK_REALTIME for both events, which suffers from
the y2038/y2106 overflow as well as time jumps.
For consistency, this changes vmwgfx to use ktime_get_ts64 as well,
which solves those problems and avoids the deprecated do_gettimeofday()
function.
This should be transparent to to user space, as long as it doesn't
compare the time against the result of gettimeofday().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
We were relying on the pinned screen object backup buffer to be destroyed
when not used. But if we hold a copy of the atomic state, like when
hibernating, the backup buffer might not be destroyed since it's
refcounted by the atomic state. This causes us to hibernate with a
buffer pinned in VRAM.
Fix this by only having the buffer pinned when it is actually used by a
screen object.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
For legacy surfaces, they were previously registered as device resources
when the driver resources were created. Since they are evictable we instead
register them as device resources once they are created on the device,
just like for guest-backed surfaces. This has implications during
hibernation where we can't hibernate with device resources active.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Use kasprintf instead of combination of kmalloc and sprintf. Also,
remove the local variables used for storing the string length as they
are not required now.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
It was used to early block fbdev dirty processing. Replace it with an
unprotected check of the par->dirty.active field. While this might
race with the vmw_fb_off() function, we do a protected check later so
the race will at worst lead to grabbing and releasing a couple of locks.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Make it possible to hibernate also with masters that don't switch VT at
hibernation time. We save and restore modesetting state unless fbdev is
active and enabled at hibernation time.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
fbdev framebuffers were previously pinned to be able to keep them mapped
across updates.
This commit introduces a mechanism that instead revalidates the map on
each update, keeping the map cached across updates. The cached map is torn
down if the underlying pages change. Typically on buffer object moves and
swapouts.
This should be nicer to the system when we have resource contention.
Testing done: Basic fbdev functionality under Fedora 27.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
The start / stop and preempt commands don't honor the context argument
but rather acts on all available contexts.
Also add detection for context 1 availability.
Note that currently there's no driver interface for submitting buffers
using the high-priority command queue (context 1).
Testing done:
Change the default context for command submission to 1 instead of 0,
verify basic desktop functionality including faulty command injection and
recovery.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
This blit was previously performed using two large vmaps, one of which
was teared down and remapped on each blit. Use the more resource-
conserving TTM cpu blit instead.
The blit is used in boundary-box computing mode which makes it possible
to minimize the bounding box used in host operations.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
The utility uses kmap_atomic() instead of vmapping the whole buffer
object. As a result there will be more book-keeping but on some
architectures this will help avoid exhausting vmalloc space and also
avoid expensive TLB flushes.
The blit utility also adds a provision to compute a bounding box of
changed content, which is very useful to optimize presentation speed
of ill-behaved applications that don't supply proper damage regions, and
for page-flips. The cost of computing the bounding box is not that
expensive when done in a cpu-blit utility like this.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
It will be used by vmwgfx cpu blit.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Use helpers to perform the kmap_atomic_prot() functionality to
a) Avoid in-function ifdefs that violate the kernel coding policy,
b) Facilitate exporting the functionality.
This commit should not change any functionality.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
The current limit of 2 leads to some GPU idle times, as the usual
IRQ latency leads to up to 3 jobs getting signaled at once with some
standard workloads.
A larger HW job limit might lead to slightly worse QoS, but we accept
that to not sacrifice GPU throughput in the common case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Use drm_plane_helper_check_update also for the cursor plane.
Some applications, like gdm on gnome shell still uses cursor front-buffer
like rendering without notifying the kernel. We do need some kind of
noficiation, but work around this for now by updating the cursor image on
every cursor move.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Page flip can be slow for vmwgfx in some cases, like need to do surface
copy to different surface or waiting for IN_FENCE_FD. Enabling
nonblocking commits for vmwgfx in case userspace request it.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Atomic ioctl can also send the same page flip flags as legacy ioctl.
In those cases also need to send the vblank event to userspace.
vmwgfx does not support flag DRM_MODE_PAGE_FLIP_ASYNC, so this flag is
never expected.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
The dmabuf_dirty/surface_dirty in case of screen object is moved to
plane atomic update, so that page flip in atomic ioctl also works.
vmwgfx does not support DRM_MODE_PAGE_FLIP_ASYNC, so this flag is never
expected.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
The function drm_crtc_arm_vblank_event should be used for the driver
which have vblank interrupt support. In case of vmwgfx we do not have
vblank interrupt.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
When display surface is different than the framebuffer surface, atomic
path do not copy the surface data. This commit moved the code to copy
surface from legacy to atomic path.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
In case of page flip there is no need to iterate over all display unit
in the function "vmw_kms_helper_dirty". If crtc is available then
dirty commands is performed on that crtc only.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
In loopback_open() and loopback_close(), we assign and release the
substream object to the corresponding cable in a racy way. It's
neither locked nor done in the right position. The open callback
assigns the substream before its preparation finishes, hence the other
side of the cable may pick it up, which may lead to the invalid memory
access.
This patch addresses these: move the assignment to the end of the open
callback, and wrap with cable->lock for avoiding concurrent accesses.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The aloop driver tries to stop the pending timer via timer_del() in
the trigger callback and in the close callback. The former is
correct, as it's an atomic operation, while the latter expects that
the timer gets really removed and proceeds the resource releases after
that. But timer_del() doesn't synchronize, hence the running timer
may still access the released resources.
A similar situation can be also seen in the prepare callback after
trigger(STOP) where the prepare tries to re-initialize the things
while a timer is still running.
The problems like the above are seen indirectly in some syzkaller
reports (although it's not 100% clear whether this is the only cause,
as the race condition is quite narrow and not always easy to
trigger).
For addressing these issues, this patch adds the explicit alls of
timer_del_sync() in some places, so that the pending timer is properly
killed / synced.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It will have a chance speaker no sound after system resume.
To toggle NID 0x53 index 0x2 bit 15 will solve this issue.
This usage will also suitable with ALC256.
Fixes: 4a219ef8f3 ("ALSA: hda/realtek - Add ALC256 HP depop function")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This platform was hardware fixed type for CTIA type for headset port.
Assigned 0x19 verb will fix can't record issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The memmap options sent to the udl framebuffer driver were not being
checked for all sets of possible crazy values. Fix this up by properly
bounding the allowed values.
Reported-by: Eyal Itkin <eyalit@checkpoint.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180321154553.GA18454@kroah.com
The bitfield dma_inuse is allocated of size dma_requests bits, thus a
valid bit address is from 0 to (dma_requests - 1).
When find_first_zero_bit() fails, it returns dma_requests as invalid
address.
Using such address for the following set_bit() is incorrect and, if
dma_requests is a multiple of BITS_PER_LONG, it will cause a buffer
overflow.
Currently this driver is only used in DT stm32h743.dtsi where a safe value
dma_requests=16 is not triggering the buffer overflow.
Fixed by checking the return value of find_first_zero_bit() _before_
using it.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit 2170dd0431
The intent of commit 2170dd0431 ("vfio-pci: Mask INTx if a device is
not capabable of enabling it") was to disallow the user from seeing
that the device supports INTx if the platform is incapable of enabling
it. The detection of this case however incorrectly includes devices
which natively do not support INTx, such as SR-IOV VFs, and further
discussions reveal gaps even for the target use case.
Reported-by: Arjun Vynipadath <arjun@chelsio.com>
Fixes: 2170dd0431 ("vfio-pci: Mask INTx if a device is not capabable of enabling it")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Since commit 3af5a67c86 ("MIPS: Fix early CM probing") the MT7621 has
not been able to boot.
This commit caused mips_cm_probe() to be called before
mt7621.c::proc_soc_init().
prom_soc_init() has a comment explaining that mips_cm_probe() "wipes out
the bootloader config" and means that configuration registers are no
longer available. It has some code to re-enable this config.
Before this re-enable code is run, the sysc register cannot be read, so
when SYSC_REG_CHIP_NAME0 is read, a garbage value is returned and
panic() is called.
If we move the config-repair code to the top of prom_soc_init(), the
registers can be read and boot can proceed.
Very occasionally, the first register read after the reconfiguration
returns garbage, so add a call to __sync().
Fixes: 3af5a67c86 ("MIPS: Fix early CM probing")
Signed-off-by: NeilBrown <neil@brown.name>
Reviewed-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.5+
Patchwork: https://patchwork.linux-mips.org/patch/18859/
Signed-off-by: James Hogan <jhogan@kernel.org>
