In rtl8xxxu_submit_int_urb if usb_submit_urb fails the allocated urb
should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to check "rtlhal->interface == INTF_PCI" twice in
_rtl_ps_inactive_ps(). The nested check is always true. Thus, the
expression can be simplified.
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rtl_usb_probe if allocation for usb_data fails the allocated hw
should be released. In addition the allocated rtlpriv->usb_data should
be released on error handling path.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'rtstatus' local variable is not used,
so remove it for clean-up.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/realtek/rtw88/rtw8822c.c:2606:9-10: WARNING: return
of 0/1 in function 'rtw8822c_dpk_coef_iq_check' with return type bool
Return statements in functions returning bool should use true/false
instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Fixes: 5227c2ee45 ("rtw88: 8822c: add SW DPK support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After firmware has been downloaded, driver should send
some information to it through H2C commands. Those H2C
commands are transmitted through TX path.
But before HCI has been started, the TX path is not
working completely. Such as PCI interfaces, the interrupts
are not enabled, hence TX interrupts will not be issued
after H2C skb has been DMAed to the device. And the H2C
skbs will not be released until the device is powered off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Interrupt is disabled to stop PCI, which means the skbs
queued for each TX ring will not be released via DMA
interrupt. To avoid those skbs remained being left in
the skb queue until PCI has been removed, driver needs
to release skbs by itself.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These skbs free routines could be used when driver wants
to stop PCI bus, because some of the skbs remained in the
queue may not have been returned via DMA interrupt.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Report chains and chain_signal in ieee80211_rx_status.
It is useful for program such as tcpdump to see if the
antennas are well connected/placed.
8822C is able to receive CCK rates with 2 antennas, while
8822B can only use 1 antenna path to receive CCK rates.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the wrong RF path for CCK rx power calculation.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92d_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92d_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware has enough buffer to receive like 8K for an MPDU.
So tell mac80211 that we can receive AMSDU in AMPDU.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This mechanism reduces the numbers of false alram in cck rate by
dynamically adjusting the value of power threshold and cs_ratio.
We determine the new value by three factors, which are rssi, false alarm
count and igi. Based on these factors, we define the current condition
into five levels. Compared to the previous level, if the level is changed,
we set the new values for power threshold and cs_ratio.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 8822c requires to do not only IQK, but also DPK.
Move these calibrations that need to be done once the channel
is determined, into phy_calibration.
And note that the order of the calibrations matters, 8822c
should do IQK first, then DPK.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power amplifiers are not linear components, and require DPK to
reduce its nonlinearity. DPK is called Digital Pre-distortion
Calibration, can be used to compensate the output of power.
DPK tracking is in charge of tracking the thermal changes. And
it then shifts the power curve accordingly, which makes the
power output remains linear even if the PA works in different
temperature.
To perform DPK, the parameter table should also be updated.
And the table will be applied when device is powered on.
Then DPK will reference the values to calibrate.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for doing IQK in firmware
Ideally the RF component's I/Q vectors should be orthogonal,
but usually they are not. So we need to calibrate for the RF
components, ex. PA/LNA, ADC/DAC.
And if the I/Q vectors are more orthogonal, the mixed signal
will have less deviation. This helps with those rates with
higher modulation (MCS8-9), because they have more strict
EVM/SNR requirement. Also the better of the quality of the
signal, the longer it can propagate, and the better throughput
performance we can get.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable 8822C Tx/Rx interrupt migration.
In some platforms, performance test may cause heavy cpu loading and get
bad results. Interrupt migration can decrease the amount of interrupts,
and lower cpu loading.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
update sequence to v13 to reduce power consumption
when MAC power off
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each of these drivers defines some device to host macros that are never
used, thus they can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iAs the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The array channel_all can be make static const rather than populating
it on the stack, this makes the code smaller. Also, variable place
is being initialized with a value that is never read, so this assignment
is redundant and can be removed.
Before:
text data bss dec hex filename
118537 9591 0 128128 1f480 realtek/rtlwifi/rtl8821ae/phy.o
After:
text data bss dec hex filename
118331 9687 0 128018 1f412 realtek/rtlwifi/rtl8821ae/phy.o
Saves 110 bytes, (gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using single_open() for opening, single_release() should be
used instead of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: 610247f46f ("rtlwifi: Improve debugging by using debugfs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using single_open(), single_release() should be used instead
of seq_release(), otherwise there is a memory leak.
This is detected by Coccinelle semantic patch.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MSI interrupt should be enabled on certain platform.
Add a module parameter disable_msi to disable MSI interrupt,
driver will then use legacy interrupt instead.
One could rebind the PCI device, probe() will pick up the
new value of the module parameter. Such as:
echo '0000:01:00.0' > /sys/bus/pci/drivers/rtw_pci/unbind
echo '0000:01:00.0' > /sys/bus/pci/drivers/rtw_pci/bind
Tested-by: Ján Veselý <jano.vesely@gmail.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Yu-Yen Ting <steventing@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a mass of jobs between spin lock and unlock in the hardware
IRQ which will occupy much time originally. To make system work more
efficiently, this patch moves the jobs to the soft IRQ (bottom half) to
reduce the time in hardware IRQ.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pointer debugfs_topdir is initialized to a value that is never read
and it is re-assigned later. The initialization is redundant and can
be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
0day reports:
sparse warnings:
drivers/net/wireless/realtek/rtw88/coex.c:2457:6: sparse:
symbol 'rtw_coex_coex_dm_reset' was not declared. Should it be static?
rtw_coex_coex_dm_reset() is not called. Remove it.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WARN_ON() macro takes a condition, not a warning message. I've
changed this to use WARN() instead.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 98fd8db59a ("rtlwifi: rtl8192ce: Convert macros that set
descriptor"), all the routines that get fields from a descriptor
were changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: 98fd8db59a ("rtlwifi: rtl8192ce: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 36eda7568f ("rtlwifi: rtl8188ee: Convert macros that set
descriptor"), all the routines that get fields from a descriptor were
changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: 36eda7568f ("rtlwifi: rtl8188ee: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit bd421dab75 ("rtlwifi: rtl8821ae: Convert macros that set
descriptor"), all the routines that get fields from a descriptor
were changed to return signed integer values. This is incorrect for the
routines that get the entire 32-bit word. In this case, an unsigned
quantity is required.
Fixes: bd421dab75 ("rtlwifi: rtl8821ae: Convert macros that set descriptor")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
and other warnings are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the TX and RX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A number of variables are initialized when declared that set later in the
routine, thus the initialization can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl reports lines too long are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
