Add @spd_limit to sata_down_spd_limit() so that the caller can specify
the SPD limit it wants. This parameter doesn't get in the way even
when it's too low. The closest possible limit is applied.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events. This patch
achieves this by doing the following.
* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
clear between BEGIN and END. ering is moved after END. The split
of persistent area is to allow hotter items remain at the head.
* ering is explicitly cleared on ata_dev_disable() and when device
attach succeeds. So, ering is persistent throug a device's life
time (unless explicitly cleared of course) and also through periods
inbetween disablement of an attached device and successful detection
of the next one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_down_spd_limit() should check whether the link is online before
using the SPD value to determine how to limit the link speed. Factor
out onlineness test and test it from sata_down_spd_limit().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_dev_disable() is about to be more tightly integrated into EH
logic. Move it to libata-eh.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The dev->pio_mode > XFER_PIO_0 test is there to avoid unnecessary
speed down warning messages but it accidentally disabled SATA link spd
down during configuration phase after reset where PIO mode is always
zero.
This patch fixes the problem by moving the test where it belongs.
This makes libata probing sequence behave better when the connection
is flaky at higher link speeds which isn't too uncommon for eSATA
devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
While playing with nvraid, I found out that rmmoding and insmoding
often trigger hardreset failure on the first port (the second one was
always okay). Seriously, how diverse can you get with hardreset
behaviors? Anyways, make ck804 use noclassify variant too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix libata kernel-doc warnings:
Warning(linux-next-20090120//drivers/ata/libata-core.c:4720): Excess function parameter 'dev' description in 'ata_qc_new'
Warning(linux-next-20090120//drivers/ata/libata-scsi.c:428): No description found for parameter 'ap'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The SSS flag, which directs the OS to spin up one disk at a time
to not have the PSU blow out, sometimes gets set even when not needed.
The effect of this is a longer-than-needed boot time.
This patch adds a module parameter that makes the driver ignore SSS
at least as far as the parallel scan during boot is concerned...
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix chip type for the Highpoint RocketRAID 1740 and 1742 PCI cards.
These really do have Marvell 6042 chips on them, rather than the 5081 chip.
Confirmed by multiple (two) users (for the 1740), and by examining
the product photographs from Highpoint's web site.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I tried compiling 2.6.29-rc1 and 2.6.29-rc3 with libata debugging enabled
and got the following error:
CC [M] drivers/ata/sata_sil.o
drivers/ata/sata_sil.c: In function 'sil_fill_sg':
drivers/ata/sata_sil.c:327: error: 'pi' undeclared (first use in this function)
drivers/ata/sata_sil.c:327: error: (Each undeclared identifier is reported only once
drivers/ata/sata_sil.c:327: error: for each function it appears in.)
make[2]: *** [drivers/ata/sata_sil.o] Error 1
make[1]: *** [drivers/ata] Error 2
make: *** [drivers] Error 2
include/linux/libata.h has the following enabled:
#define ATA_DEBUG
#define ATA_VERBOSE_DEBUG
#define ATA_IRQ_TRAP
This fixes the compilation.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI hotplug: Change link order of pciehp & acpiphp
PCI hotplug: fakephp: Allocate PCI resources before adding the device
PCI MSI: Fix undefined shift by 32
PCI PM: Do not wait for buses in B2 or B3 during resume
PCI PM: Power up devices before restoring their state
PCI PM: Fix hibernation breakage on EeePC 701
PCI: irq and pci_ids patch for Intel Tigerpoint DeviceIDs
PCI PM: Fix suspend error paths and testing facility breakage
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
fbdev/atyfb: Fix DSP config on some PowerMacs & PowerBooks
powerpc: Fix oops on some machines due to incorrect pr_debug()
powerpc/ps3: Printing fixups for l64 to ll64 convserion drivers/net
powerpc/5200: update device tree binding documentation
powerpc/5200: Bugfix for PCI mapping of memory and IMMR
powerpc/5200: update defconfigs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
pxamci: enable DMA for write ops after CMD/RESP
pxamci: replace #ifdef CONFIG_PXA27x with if (cpu_is_pxa27x())
ricoh_mmc: Use suspend_late/resume_early
mmci: Add support for ST Micro derivate
mmc: Add a MX2/MX3 specific SDHC driver
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
icside: fix PCB version 6 support (v2)
tx4939ide: typo fix and minor cleanup
ide: add CS5536 host driver (v3)
ide: Force VIA IDE legacy interrupts for AmigaOne boards
IDE: Unregister and disable devices if initialization fails.
ide: fix ide_register_port() failure handling
ide: struct device - replace bus_id with dev_name(), dev_set_name()
ide-cd: fix DMA for non bio-backed requests
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: lock rc->rsvs_lock with spin_lock_bh()
wusb: timeout when waiting for ASL/PZL updates in whci-hcd
uwb: remove unused #include <version.h>'s
wusb: return -ENOTCONN when resetting a port with no connected device
uwb: safely remove all reservations
The host really shouldn't be notifying us of config changes
before the device status is VIRTIO_CONFIG_S_DRIVER or
VIRTIO_CONFIG_S_DRIVER_OK.
However, if we do happen to be interrupted while we're not
attached to a driver, we really shouldn't oops. Prevent
this simply by checking that device->driver is non-NULL
before trying to notify the driver of config changes.
Problem observed by doing a "set_link virtio.0 down" with
QEMU before the net driver had been loaded.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without this the 2nd port gets first ports MAC addr.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the PXA270 MMC hardware, there seems to be an issue of
data corruption on writes where a 4KB data block is offset
by one byte.
If we delay enabling the DMA for writes until after the CMD/RESP
has finished, the problem seems to be fixed.
related to PXA270 Erratum #91
Tested-by: Vernon Sauder <VernonInHand@gmail.com>
Signed-off-by: Cliff Brake <cbrake@bec-systems.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
If ricoh_mmc suspends before sdhci_pci, it will pull the card
out from under the controller, which could leave the system in
a very confused state.
Using suspend_late/resume_early ensures that sdhci_pci suspends first
and resumes second.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds support for the ST Microelectronics version of
the PL180 PrimeCell. They use designer ID 0x80 and have a few
alterations/bugfixes related to open drain and HW flow control.
They also add some SDIO registers, I am unsure if these are
in ST HW only or if this is things also added in later ARM
revisions, but they are included in the mmci.h file for
completeness.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds a MX2/MX3 specific SDHC driver. The hardware is basically
the same as in the MX1, but unlike the MX1 controller the MX2
controller just works as expected. Since the MX1 driver has more
workarounds for bugs than anything else I had no success with supporting
MX1 and MX2 in a sane way in one driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
We need to pass struct ide_port_info also to ide_host_register().
v2:
Fix v5/v6 mismatch noticed by Russell.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The bcount is greater than 0 and less than or equal to 0x10000.
Thus '(bcount & 0xffff) == 0x0000' can be simplified as 'bcount == 0x10000'.
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is a port of libata's pata_cs5536.c (written by Martin K. Petersen)
to IDE subsystem.
Changes done while at it:
* Reprogram PIO/MWDMA timings if needed before and after DMA transfer
(chipset uses shared PIO/MWDMA timings).
* Fix cable detection to report 80-wires cable if BIOS set it for any
device on a port (IDE core will do drive-side cable detection later).
* Don't disable UDMA while programming PIO timings.
* Simplify PCI/MSR support.
Pros of having IDE host driver in addition to libata's one:
* IDE is much lighter than SCSI+libata, the host driver itself is also
a bit smaller:
text data bss dec hex filename
1261 496 4 1761 6e1 drivers/ata/pata_cs5536.o
1242 128 4 1374 55e drivers/ide/cs5536.o
* This allows use of IDE features which are unavailable under libata.
v2:
* Fixes per review from Sergei:
- simplify dependency check in Kconfig
- use IDE_DRV_MASK also for ->drive_data
- disable UDMA when programming MWDMA
- program new DTC timings only when necessary
- fix printk() level in cs5536_init_one()
* Fix patch description according to comments from Alan and Sergei.
v3:
* Smarter masking of UDMA bits per Sergei's suggestion.
Cc: Martin K. Petersen <mkp@mkp.net>
Cc: Karl Auerbach <karl@iwl.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The AmigaOne uses the onboard VIA IDE controller in legacy mode (like the
Pegasos).
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On reboot the loop in device_shutdown gets confused by these partially
initialized devices and goes into an infinite loop. Therefore unregister
and disable these devices.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
[bart: remove leftover hwif->present clearing + update patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out port freeing from ide_host_free() to ide_free_port().
* Add ide_disable_port() and use it on ide_register_port() failure.
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the complete re-write in 2.6.10, some PowerMacs (At least PowerMac 5500
and PowerMac G3 Beige rev A) with ATI Mach64 chip have suffered from unstable
columns in their framebuffer image. This seems to depend on a value (4) read
from PLL_EXT_CNTL register, which leads to incorrect DSP config parameters to
be written to the chip. This patch uses a value calculated by aty_init_pll_ct
instead, as a starting point.
There are questions as to whether this should be extended to other platforms
or maybe made dependent on specific chip types, but in the meantime, this has
been tested on various powermacs and works for them so let's commit it.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Tested-by: Michael Pettersson <mike@it.uu.se>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Just like with the s5h1411, the s5h1409 needs a soft-reset in order for it
to know that the tuner has been told to change frequencies. This change
changes the behavior from "random tuning times between 500ms to complete
tuning lock failures" to "tuning lock consistently within 700ms".
Thanks to Robert Krakora <rob.krakora@messagenetsystems.com> for doing
initial testing of the patch on the KWorld 330U.
Thanks to Andy Walls <awalls@radix.net> for doing testing of the patch on
the HVR-1600.
Thanks to Michael Krufky <mkrufky@linuxtv.org> for doing additional testing.
Signed-off-by: Devin Heitmueller <dheitmueller@linuxtv.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According with saa7130 public datasheet, saa7130 doesn't support
digital audio. This is also confirmed by experimental tests. So, it
doesn't make sense to let saa7134-alsa register for those chipsets.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New year, new copyright date ranges. Also bump the driver version
number to reflect many of the recent changes.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our current MSI-X allocation mechanism does not support new hardware
at all. It also isn't getting the actual number of supported MSI-X vectors
from the device.
This patch allows the number of MSI-X vectors to be specific to a device,
plus it gets the number of MSI-X vectors available from PCIe configuration
space.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device ID for BX devices using the 82598 MAC.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This turns the fec driver into a platform device driver for new
platforms. Old platforms are still supported through a FEC_LEGACY define
till they are also ported.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_dcache_range is not portable across architectures. Use
dma_sync_single instead. Also, the memory must be synchronised in the
receive path aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the datasheet the ICSR register is at offset 27, not 22.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some architecture specific functions which are all
empty. Remove them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The #else branches throughout this driver belong to a PowerPC 8xx for
which this driver is not used.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes following sparse warnings:
CHECK gianfar_ethtool.c
gianfar_ethtool.c:610:26: warning: symbol 'gfar_ethtool_ops' was not declared. Should it be static?
CHECK gianfar_mii.c
gianfar_mii.c:108:35: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:119:35: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:128:35: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:272:5: warning: cast removes address space of expression
gianfar_mii.c:271:15: warning: cast adds address space to expression (<asn:2>)
gianfar_mii.c:340:11: warning: cast adds address space to expression (<asn:2>)
CHECK gianfar_sysfs.c
gianfar_sysfs.c:84:1: warning: symbol 'dev_attr_bd_stash' was not declared. Should it be static?
gianfar_sysfs.c:133:1: warning: symbol 'dev_attr_rx_stash_size' was not declared. Should it be static?
gianfar_sysfs.c:175:1: warning: symbol 'dev_attr_rx_stash_index' was not declared. Should it be static?
gianfar_sysfs.c:213:1: warning: symbol 'dev_attr_fifo_threshold' was not declared. Should it be static?
gianfar_sysfs.c:250:1: warning: symbol 'dev_attr_fifo_starve' was not declared. Should it be static?
gianfar_sysfs.c:287:1: warning: symbol 'dev_attr_fifo_starve_off' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In most cases (e.g. PCI drivers) MDIO and MAC controllers are
represented by the same device. But for SOC ethernets we have
separate devices. So, in SOC case, checking whether MDIO
controller may wakeup is not only makes little sense, but also
prevents us from doing per-netdevice wakeup management.
This patch reworks suspend/resume code so that now it checks
for net device's wakeup flags, not MDIO controller's ones.
Each netdevice should manage its wakeup flags, and phylib will
decide whether suspend an attached PHY or not.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements wakeup management for the gianfar driver.
The driver should set wakeup enable if WOL is enabled, so that
phylib won't power off an attached PHY.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some platforms (for example pcm037) do not have an EEPROM fitted,
instead storing their mac address somewhere else. The bootloader
fetches this and configures the ethernet adapter before the kernel is
started.
This patch allows a platform to indicate to the driver via the
SMSC911X_SAVE_MAC_ADDRESS flag that the mac address has already been
configured via such a mechanism, and should be saved before resetting
the chip.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
On LAN9115/LAN9117/LAN9215/LAN9217, external phys are supported. These
are usually indicated by a hardware strap which sets an "external PHY
detected" bit in the HW_CFG register.
In some cases it is desirable to override this hardware strap and force
use of either the internal phy or an external PHY. This patch adds
SMSC911X_FORCE_INTERNAL_PHY and SMSC911X_FORCE_EXTERNAL_PHY flags so a
platform can indicate this preference via its platform_data.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The isr supports shared operation, so register it with the IRQF_SHARED
flag to indicate this.
This patch also removes the IRQF_DISABLED flag. This driver doesn't
need it, and IRQF_DISABLED isn't guaranteed when using shared interrupts.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch adds support for the platform_device's resources to indicate
additional flags to use when registering the irq, for example
IORESOURCE_IRQ_LOWLEVEL (which corresponds to IRQF_TRIGGER_LOW). These
should be set in the irq resource flags field.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 setup: fix asm constraints in vesa_store_edid
xen: make sysfs files behave as their names suggest
x86: tone down mtrr_trim_uncached_memory() warning
x86: correct the CPUID pattern for MSR_IA32_MISC_ENABLE availability
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
leds: Fix bounds checking of wm8350->pmic.led
regulator: move bq24022 init back to module_init instead of subsys_initcall
Fix an off-by-two memory error in console selection.
The loop below goes from sel_start to sel_end (inclusive), so it writes
one more character. This one more character was added to the allocated
size (+1), but it was not multiplied by an UTF-8 multiplier.
This patch fixes a memory corruption when UTF-8 console is used and the
user selects a few characters, all of them 3-byte in UTF-8 (for example
a frame line).
When memory redzones are enabled, a redzone corruption is reported.
When they are not enabled, trashing of random memory occurs.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
igb: fix link reporting when using sgmii
igb: prevent skb_over panic w/ mtu smaller than 1K
igb: Fix DCA errors and do not use context index for 82576
ipv6: compile fix for ip6mr.c
packet: Avoid lock_sock in mmap handler
sfc: Replace stats_enabled flag with a disable count
sfc: SFX7101/SFT9001: Fix AN advertisements
sfc: SFT9001: Always enable XNP exchange on SFT9001 rev B
sfc: Update board info for hardware monitor on SFN4111T-R5 and later
sfc: Test for PHYXS faults whenever we cannot test link state bits
sfc: Reinitialise the PHY completely in case of a PHY or NIC reset
sfc: Fix post-reset MAC selection
sfc: SFN4111T: Fix GPIO sharing between I2C and FLASH_CFG_1
sfc: SFT9001: Fix speed reporting in 1G PHY loopback
sfc: SFX7101: Remove workaround for bad link training
sfc: SFT9001: Enable robust link training
sky2: fix hard hang with netconsoling and iface going up
The mmap_region() code would temporarily set the VM_ACCOUNT flag for
anonymous shared mappings just to inform shmem_zero_setup() that it
should enable accounting for the resulting shm object. It would then
clear the flag after calling ->mmap (for the /dev/zero case) or doing
shmem_zero_setup() (for the MAP_ANON case).
This just resulted in vma merge issues, but also made for just
unnecessary confusion. Use the already-existing VM_NORESERVE flag for
this instead, and let shmem_{zero|file}_setup() just figure it out from
that.
This also happens to make it obvious that the new DRI2 GEM layer uses a
non-reserving backing store for its object allocation - which is quite
possibly not intentional. But since I didn't want to change semantics
in this patch, I left it alone, and just updated the caller to use the
new flag semantics.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using sgmii the link was not being properly passed up to the driver
from the underlying link management functions. This change corrects it so
that get_link_status is cleared when a link has been found.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A panic has been observed with frame sizes smaller than 1K. This has been
root caused to the hardware spanning larger frames across multiple buffers
and then reporting the original frame size in the first descriptor. To
prevent this we can enable set the LPE bit which in turn will restrict
packet sizes to those set in the RLPML register.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82576 was being incorrectly flagged as needing a context index. It does not as
each ring has it's own table of 2 contexts.
Driver was registering after registering the driver instead of the other way around.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/char/nvram.c uses rtc_lock, that (on ARM) is only defined if
RTC_DRV_CMOS is enabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
"flash" is a very generic name for a platform_driver that is only
available on SA11x0.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Nicolas Pitre <nico@marvell.com>
Currently we use a spin-lock to serialise statistics fetches and also
to inhibit them for short periods of time, plus a flag to
enable/disable statistics fetches for longer periods of time, during
online reset. This was apparently insufficient to deal with the several
reasons for stats being disabled.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 10Xpress PHYs require autonegotiation all the time; enforce this
in the set_settings() method and do not treat it as a workaround.
Remove claimed support for 100M HD mode since it is not supported by
current firmware.
Do not set speed override bits when AN is enabled, and do not use
register 1.49192 for AN configuration as it can override what we set
elsewhere.
Always set the AN selector bits to 1 (802.3).
Fix confusion between Next Page and Extended Next Page.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround is not specific to rev A.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the loopback mode, there may be no pertinent link state
bits. In this case we test the PHYXS RX fault bit instead. Make
sure to do this in all cases where there are no link state bits.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, set pause advertising bits properly.
A PHY reset is not necessary to recover from the register self-test,
so use a "invisible" reset there instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the
MAC is the same as it was before. This ensures that the value is
correct after an online reset.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change sfn4111t_reset() to change only GPIO output enables so that it
doesn't break subsequent I2C operations.
Update comments to explain exactly what we're doing.
Add a short sleep to make sure the FLASH_CFG_1 value is latched before
any subsequent I2C operations.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of disabling AN in loopback, just prevent restarting AN and
override the speed in sft9001_get_settings().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Early versions of the SFX7101 firmware could complete link training in
a state where it would not adequately cancel noise (Solarflare bug
10750). We previously worked around this by resetting the PHY after
seeing many Ethernet CRC errors. This workaround is unsafe since it
takes no account of the interval between errors; it also appears to
be unnecessary with production firmware. Therefore remove it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable a firmware option that appears to be necessary for reliable
operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing anything over netconsole before hw is up and running is,
of course, not going to work.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This workaround was needed when regulator/ was not linked before both
power/ and usb/otg/ in drivers/Makefile. Now that it is even linked
before mfd/, this patch makes sure that bq24022 isn't probed before the
GPIO expander is set up.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Removing the module was slow because ath9k_hw_stopdma()
was looping for a long time quantum. Use reasonable
values now to fix this issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue where hw_value_short was not being filled
with the proper ratecode during rate registration, but was being used
in the RX path for decoding the packet rate.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_sta pointer in the SKB's TX control info
area is not guaranteed to be valid after returning from the tx() callback.
Use ieee80211_find_sta() instead and return early if the station
is no longer present.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default chainmask for AR9280 is 3, so handle that when setting
the supported MCS rates. Also, check for the HW supported chainmask
when choosing single/dual stream.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tulip: fix 21142 with 10Mbps without negotiation
drivers/net/skfp: if !capable(CAP_NET_ADMIN): inverted logic
gianfar: Fix Wake-on-LAN support
smsc911x: timeout reaches -1
smsc9420: fix interrupt signalling test failures
ucc_geth: Change uec phy id to the same format as gianfar's
wimax: fix build issue when debugfs is disabled
netxen: fix memory leak in drivers/net/netxen_nic_init.c
tun: Add some missing TUN compat ioctl translations.
ipv4: fix infinite retry loop in IP-Config
net: update documentation ip aliases
net: Fix OOPS in skb_seq_read().
net: Fix frag_list handling in skb_seq_read
netxen: revert jumbo ringsize
ath5k: fix locking in ath5k_config
cfg80211: print correct intersected regulatory domain
cfg80211: Fix sanity check on 5 GHz when processing country IE
iwlwifi: fix kernel oops when ucode DMA memory allocation failure
rtl8187: Fix error in setting OFDM power settings for RTL8187L
mac80211: remove Michael Wu as maintainer
...
This fixes a crash observed when non-existant enable_ms function is
called for jsm driver.
Signed-off-by: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Paul Larson <pl@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit e57db7b (SATA Sil: Blacklist system that spins off disks during ACPI power off)
breaks build like the following, in both cases when CONFIG_DMI set or not.
drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast
sata_sil.c should include dmi.h
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move DMA-mapping.txt to Documentation/PCI/.
DMA-mapping.txt was supposed to be moved from Documentation/ to
Documentation/PCI/. The 00-INDEX files in those two directories
were updated, along with a few other text files, but the file
itself somehow escaped being moved, so move it and update more
text files and source files with its new location.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver-core: fix kernel-doc parameter name
UIO: Add missing documentation of features added recently
Sync patch for jp_JP/stable_kernel_rules.txt
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: document difference between hid_blacklist and hid_ignore_list
HID: add antec-branded soundgraph imon devices to blacklist
HID: fix reversed logic in disconnect testing of hiddev
HID: adjust report descriptor fixup for MS 1028 receiver
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: Fix a memory leak with the lg object during launcher close
lguest: disable the FORTIFY for lguest.
lguest: typos fix
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: sbp2: add workarounds for 2nd and 3rd generation iPods
firewire: sbp2: add workarounds for 2nd and 3rd generation iPods
firewire: sbp2: fix DMA mapping leak on the failure path
firewire: sbp2: define some magic numbers as macros
firewire: sbp2: fix payload limit at S1600 and S3200
ieee1394: sbp2: don't assume zero model_id or firmware_revision if there is none
ieee1394: sbp2: fix payload limit at S1600 and S3200
ieee1394: sbp2: update a help string
ieee1394: support for speeds greater than S800
firewire: core: optimize card shutdown
ieee1394: ohci1394: increase AT req. retries, fix ack_busy_X from Panasonic camcorders and others
firewire: ohci: increase AT req. retries, fix ack_busy_X from Panasonic camcorders and others
firewire: ohci: change "context_stop: still active" log message
firewire: keep highlevel drivers attached during brief connection loss
firewire: unnecessary BM delay after generation rollover
firewire: insist on successive self ID complete events
If the initial state is not set when the input device is set up, the first
docking event after the module is loaded will be lost.
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MacPro 3 have more temperature sensors than the previous MacPro's also the
sensor THTG has been removed. This patch add supports for the newer
temperature sensors in the MacPro3.
Signed-off-by: Bharath Ramesh <bramesh@vt.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bump hpilo module version to indicate that the open/close bug is fixed.
Signed-off-by: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error was introduced in commit fe8e4e039d ("hp-wmi: handle
rfkill_register() failure").
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Matthew Garrett <mjg@redhat.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up the stale DBUG_ON checks and add a couple new ones.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the bte copy fails, the attempt to retrieve payloads merely returns a
null pointer deref and not NULL as was expected.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clearing of the msg->flags needs a barrier between it and the notify
of the channel threads that the messages are cleaned and ready for use.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
with current kernels, tulip 21142 ethernet controllers fail to connect
to a 10Mbps only (i.e. without negotiation-partner) network. It used
to work in 2.4 kernels. Fix that. Tested on a 21142 Rev 0x11.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 0f0ca340e5 ("phy: power
management support") caused a regression in the gianfar driver.
Now phylib turns off PHY power during suspend, and thus WOL
doesn't work anymore.
This patch workarounds the issue by enabling wakeup in the MDIO
device, i.e. just restores the old behaviour for the gianfar
driver. Note that this way all PHYs on a given MDIO bus won't
be turned off during suspend, which isn't good from the power
saving point of view.
A proper, per netdevice wakeup management support will need
a bit reworked phylib suspend/resume logic.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc9420 performs an interrupt signalling test when the interface is
brought up. The current code mistakenly sets its test flag to false
AFTER enabling the software interrupt source, making failure quite
likely.
This patch changes the code to set the test flag BEFORE enabling
interrupts. I've also removed an smp_wmb because the following spinlock
provides an implicit memory barrier.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit b31a1d8b41 ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx". For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Toralf Förster and Randy Dunlap.
- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html
- http://lkml.org/lkml/2009/1/29/279
The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.
These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory leak identified by Rusty Russell during LCA09 by
kfree'ing the lg object instead of just clearing it when the
launcher closes.
Signed-off-by: Mark Wallis <mwallis@serialmonkey.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.
This was reduced in commit 32ec803348
("netxen: reduce memory footprint").
Raising jumbo ring size from 512 to 1024, adds ~4MB per port, but
there's still big saving because of original patch (~20MB per port).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath5k_config updates the software context without taking sc->lock.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Versioning for ath9k is pointless we have kept it at 0.1
since the initial release so its meaningless. We put more emphasis
on kernel release or dated wireless-testing master tag
as per John's tagging.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix AR9285 specific noise floor reads and initialize tx and rx
chainmask during reset. This along with the following earlier
patches of ath9k fixes an issue with association noticed in
noisy environment.
ath9k: Fix typo in chip version check
ath9k: Remove unnecessary gpio configuration in ath9k_hw_reset()
ath9k: Fix bug in NF calibration
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With debugging enabled and with ATH_DBG_REGULATORY
selected we wouldn't get the full print out of one line,
reason is we used "," instead of nothing to separate two
lines.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add vendor ID for AMBIT and use it to set the ath5k LED gpio.
base.c:
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Tulio Magno Quites Machado Filho <tuliom@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dynamically control the log verbosity with a module parameter.
This enables us to dynamically enable debugging messages (or disable
info, warn, error messages) via module parameter or /sys/module/b43/parameters/verbose.
This increases the module size by about 3k. But in practice it reduces the
module size for the user, because some distributions ship the b43 module
with CONFIG_B43_DEBUG set, which increases the module by about 15k.
So with this patch applied, distributions should really _disable_ CONFIG_B43_DEBUG.
There is no reason to keep it in a production-release kernel.
So we have a net reduction in size by about 12k.
This patch also adds a printk of the wireless core revision, so people
don't have to enable SSB debugging to get the wireless core revision.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows the mac80211 high level code to access the TSF. This is e.g. needed for BSSID merges in the IBSS mode.
The second version adds locking and removes the now unnecessary debugfs entries.
Thanks to Michael Buesch! :)
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables low-level driver independent debugging of the TSF and remove the driver specific things of ath5k and ath9k from the debugfs.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix compilation warning in printk formatting
iwl_tx_queue_alloc function.
Cleanup the code a bit on the way.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix compile warning for non-debug builds:
drivers/net/wireless/b43/phy_g.c: In function ‘b43_gphy_op_recalc_txpower’:
drivers/net/wireless/b43/phy_g.c:3195: warning: unused variable ‘dbm’
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get_wep_key() and set_wep_key() combind both get/set of the actual WEP
key and get/set of the transmit index into the same functions. Split those
out so it's clearer what is going one where. Add error checking to WEP
key hardware operations too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do the computation once at init time; don't ask the hardware
every time.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The capability register has to be read for other (upcoming) stuff, so fold
the WPA test function back into _init_airo_card() and move the netdevice
registration stuff above it so that the netdevice has a name by the time
the card's capabilities are printed out.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split each specific interrupt-time task out into its own function to
make airo_interrupt() actually readable.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This pach make use of 39 own scan probe mask
the variables or of different types
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the recent host command routines merge, we can now look at the various
host command helpers and get rid of the duplicated ones.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to be in sync with the agn code, we're ading a fw_restart3945 module
parameter to iwl3945.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwl_priv antenna field is useless as we can simply use the corresponding
mod_params antenna field.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IWL3945_DEBUG is pointless and obsolete. We already have an IWLWIFI_DEBUG
symbol, that needs to be set if we actually want to get 3945 debug (see
iwl-debug.h).
Thus, we can simply get rid of this symbol.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By removing the init_rates() routine outside of the init_geos() one, we can
share the geos routines between 3945 and agn.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By adding the eeprom ops to the 3945 code, we can now use the iwlcore eeprom
routines (defined in iwl-eeprom.c).
We also removed the heavy eeprom39 reference from iwl_priv and use the eeprom
pointer instead.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By adding an additional hw_params (tfd_size) and a new iwl_lib ops (txq_init),
we can now use the iwlcore TX queue management routines.
We had to add a new hw_params because we need to allocate the right DMA buffer
for TFDs, and those have a different sizes depending if you're on 3945 or agn.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having both tfds and tfds39, we can just have a void *tfds.
It makes the tx_queue structure nicer, and the code cleaner. It also helps
with further TX queues management code merging.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A lot of the scanning related code is duplicated between 3945 and agn. Let's
use the iwlcore one and get rid of the 3945.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can define this iwl_lib ops for 3945, as this would help us cleaning the
scanning code.
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
