To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix the "unused variable" warning in init_hwif_scc() caused by the commit
48c3c10726 (ide: add struct ide_host (take 3)).
Moreover, remove the write-only variable 'dma_status_port' in init_setup_scc()
about which gcc gives no warning and which has been there from the very start...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
By the time ide_dma_sgiioc4() gets called, sgiioc4_ide_setup_pci_device() will
have called ioremap() on the whole BAR0 region, so calling ioremap() on the DMA
registers means wasting a page. Replace this call by a mere address calculation,
based on the fact that IRQ registers (pointed to by 'hwif->io_ports.irq_addr')
are situated at offset 0 from BAR0.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: jeremy@sgi.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The driver performs a number of checks on the virtual/physical addresses which
would always evaluate as true (except ide_dma_sgiioc4() -- always false):
- for sgiioc4_init_hwif_ports(), its caller, sgiioc4_ide_setup_pci_device(),
guarantees that 'ctrl_port' and 'irq_port' parameters are never 0;
- in sgiioc4_read_status(), we always read the IDE status register, so there's
no need to check the register's address (must be a leftover from the times
when this function implemented the INB() method);
- in ide_dma_sgiioc4(), 'dma_base' can never be 0 as IOC4_DMA_OFFSET is not 0.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: jeremy@sgi.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
No big loss since HPT343/363 controllers are properly supported
by pata_hpt3x3 driver from Alan Cox.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the maskproc() method calls either mirror the interrupt en/disable via
the nIEN bit of the device control register done by the IDE core before issuing
a command or unmask the interrupt after a command executed in polled mode (when
interrupt is already not expected), it is pointless to implement this method
by manipulating the nIEN bit...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: jeremy@sgi.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since the maskproc() method calls either mirror the interrupt en/disable via
the nIEN bit of the device control register done by the IDE core before issuing
a command or unmask the interrupt after a command executed in polled mode (when
interrupt is already not expected), it is pointless to manipulate the nIEN bit
in this method; therefore, just do nothing for the drives not on the quirk list.
Move the code to the left by using an early return and the 'else if' construct,
while at it....
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: fix checkpatch.pl warning]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently, there is no sense in unmasking IRQ on the controller when you call
disable_irq_nosync() before doing this, set the nIEN bit afterwards, and then
unmask IRQ again after the command completion, hence 0 passed to SELECT_MASK()
before issuing the command in ide_config_drive_speed() is probably just a typo.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add some more verbosity to key function calls in ide-cd debug code. While at it,
delete a superfluous comment.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Turn ide_driver_t's 'proc' field into ->proc_entries method
(and also 'settings' field into ->proc_devsets method). Then
update all device drivers accordingly.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- idefloppy_do_request() -> ide_floppy_do_request()
- idefloppy_end_request() -> ide_floppy_end_request()
- idefloppy_setup() -> ide_floppy_setup()
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set IDE_DFLAG_MEDIA_CHANGED in ide_gd_open() to signalize
ide_gd_media_changed() that that media has changed (instead
of relying on IDE_DFLAG_REMOVABLE).
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Just use IDE_DFLAG_DOORLOCKING instead.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use drive->capacity64 for caching current capacity.
* Switch ide_floppy_capacity() to use drive->capacity64.
* Call set_capacity() in idefloppy_open() and ide_floppy_probe()
instead of ide_floppy_get_capacity().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Some code in idedisk_setup() should be in idedisk_capacity() instead.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
Using "def_bool n" is pointless, simply using bool here appears more
appropriate.
Further, retaining such options that don't have a prompt and aren't
selected by anything seems also at least questionable.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that device_create() has been audited, rename things back to the
original call to be sane.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (66 commits)
ata: Add documentation for hard disk shock protection interface (v3)
ide: Implement disk shock protection support (v4)
ide-cd: fix printk format warning
piix: add Hercules EC-900 mini-notebook to ich_laptop short cable list
ide-atapi: assign taskfile flags per device type
ide-cd: move cdrom_info.dma to ide_drive_t.dma
ide: add ide_drive_t.dma flag
ide-cd: add a debug_mask module parameter
ide-cd: convert driver to new ide debugging macro (v3)
ide: move SFF DMA code to ide-dma-sff.c
ide: cleanup ide-dma.c
ide: cleanup ide_build_dmatable()
ide: remove needless includes from ide-dma.c
ide: switch to DMA-mapping API part #2
ide: make ide_dma_timeout() available also for CONFIG_BLK_DEV_IDEDMA_SFF=n
ide: make ide_dma_lost_irq() available also for CONFIG_BLK_DEV_IDEDMA_SFF=n
ide: __ide_dma_end() -> ide_dma_end()
pmac: remove needless pmac_ide_destroy_dmatable() wrapper
pmac: remove superfluous pmif == NULL checks
ide: Two fixes regarding memory allocation
...
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop expected
to hit the floor). Port resets are deferred whenever a device on that
port is in the parked state.
v3:
Elias Oltmanns <eo@nebensachen.de> wrote:
[...]
> >> 1. Make sure that no negative value is being passed to
> >> jiffies_to_msecs() in ide_park_show().
> >> 2. Drop the superfluous variable hwif in ide_special_rq().
> >> 3. Skip initialisation of task and tf in ide_special_rq() if we are not
> >> handling a (un)park request.
> >
> > Well, #3 should have been done differently because we donn't want to
> > check for REQ_(UN)?PARK_HEADS more often than is necessary.
>
> While preparing the backport to 2.6.27, it has just occurred to me that
> we need to clear the IDE_DFLAG_PARKED flag in ide_disk_pre_reset()
> because this flag must not be set after *any* sort of access to the
> device.
v4:
Fix a memory leak due to a missing blk_put_request() in
issue_park_cmd(). Additionally, we should plug the queue when enqueueing
the unpark request because there is no guarantee that the park timeout
has not expired by then. Even though the chance for that to happen is
very slim, the request might end up hanging in the queue until the next
I/O operation is queued up. While at it, clean up the code a little:
- make issue_park_cmd() a function of type void since nobody cares for
the return value anyway;
- use blk_start_queueing() instead of __blk_run_queue() since we don't
have to worry about recursion;
- remove a superfluous pointer deference in task_no_data_intr().
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: Jeff Garzik <jeff@garzik.org>,
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This flag is to accomodate ide-cd functionality into ide atapi.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: no need to zero debug_mask + move it next to module_param()]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also,
- leave in the possibility for optimizing away all debugging macros
- add a PFX macro and prepend all printk calls with it for consistency
- add debug macro calls in important driver paths
- remove #if 0-ed code
- mv restore_request -> ide_cd_restore_request
- add a driver registration printk
v2:
failed_command can be NULL so check it before accessing it
v3:
fix another NULL ptr in debug statement
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
- use for_each_sg()
- move printing 'DMA table too small' message below use_pio_instead label
- merge '64KB bug' comment with function documentation
- fix intendation
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Follow-up to commit 5c05ff68b9
("ide: switch to DMA-mapping API"):
* pci_{alloc,free}_consistent() -> dma_{alloc,free}_coherent()
in ide_{allocate,release}_dma_engine().
* Add ->prd_max_nents and ->prd_ent_size fields to ide_hwif_t
(+ set default values in ide_allocate_dma_engine()).
* Make ide_{allocate,release}_dma_engine() available also
for CONFIG_BLK_DEV_IDEDMA_SFF=n. Then convert au1xxx-ide.c,
scc_pata.c and sgiioc4.c to use them.
* Add missing ->init_dma method to scc_pata.
This patch also fixes:
- ->dmatable_cpu leak for au1xxx-ide
- too early realease of ->dmatable_cpu for scc_pata
- wrong amount of ->dmatable_cpu memory being freed for sgiioc4
While at it:
- remove superfluous ->dma_base check from ide_unregister()
- return -ENOMEM on error in ide_release_dma_engine()
- beautify error message in ide_release_dma_engine()
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make ide_dma_timeout() available also for CONFIG_BLK_DEV_IDEDMA_SFF=n
and convert {ics,au1xxx-}ide.c to use it.
While at it:
- dump ATA Status register content on error
- use EXPORT_SYMBOL_GPL() to match the rest of SFF DMA functions
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make ide_dma_lost_irq() available also for CONFIG_BLK_DEV_IDEDMA_SFF=n
and convert {ics,au1xxx-}ide.c to use it.
While at it:
- use EXPORT_SYMBOL_GPL() to match the rest of SFF DMA functions
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- use EXPORT_SYMBOL_GPL() to match the rest of SFF DMA functions
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hwif->sg_nents is always != 0 when this function is called
and there is also no need to explicitely zero hwif->sg_nents.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In function ide_devset_execute() we should use __GFP_WAIT rather than
GFP_KERNEL. Also, the allocation cannot possibly fail at that point.
More importantly, there is a potential memory leak in the device probing
code. The infrastructure seems rather complex and I hope I haven't messed
anything up by trying to fix this.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
[bart: remove superfluous ide_lock taking]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
- idefloppy_ioctl() -> ide_floppy_ioctl()
v2:
Fix for idefloppy_ioctl name change from Stephen Rothwell.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set IDE_AFLAG_DRQ_INTERRUPT in do_identify() instead of ATAPI
device drivers *_setup() methods.
While at it:
- use ata_id_cdb_intr()
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer used ide_host_alloc_all().
* Add MAX_HOST_PORTS define and use it instead of MAX_HWIFS
as the maximum number of host ports possible.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There is now a generic solution [ide_generic_check_pci_legacy_iobases()]
so MIPS-specific ide_probe_legacy() is no longer necessary.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ->ide_dma_clear_irq method to ->clear_irq
and move it from ide_hwif_t to struct ide_port_ops.
* Move ->waiting_for_dma check inside ->clear_irq method.
* Move ->dma_base check inside ->clear_irq method.
piix.c:
* Add ich_port_ops and remove init_hwif_ich() wrapper.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct task_s' to ide_hwif_t and init it to the current command
in do_rw_taskfile().
* Merge all TASKFILE_NO_DATA data phase handlers into taskfile_no_intr().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out reset error reporting from reset_pollfunc()
to ide_reset_report_error() helper.
While at it:
- fix KERN_* printk() levels
- remove 'switch ()'
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'drive->dn & 1' in ide_init_disk().
* remove [ata_]select_t.
While at it:
* Use ATA_DEVICE_OBS define in ide_port_init_devices_data().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Call ide_port_init_devices() in ide_host_register()
also if 'struct ide_port_info *d' is not available.
* Init drive->dn in ide_port_init_devices() instead of
ide_probe_port() so it is valid also in ->init_dev.
* Pass device number to ide_dev_apply_params().
* Use 'drive->dn & 1' instead of drive->select.b.unit.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ide*_pm_* enums from ide-io.c to <linux/ide.h>.
* idedisk_pm_* -> ide_pm_*
* ide_pm_state_* -> ide_pm_*
* No need to set ide_pm_* enums to the fixed values.
* Uppercase ide_pm_* enums.
* Fix/update comments.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_DFLAG_LBA device flag and use it instead of ->select.b.lba.
Since ->tf_load uses ->select.all for ATA Device/Head register this
fixes HDIO_DRIVE_TASK[FILE] ioctls for CHS commands on LBA devices.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_DFLAG_DMA_PIO_RETRY and use it instead of
ide_drive_t.state + DMA_PIO_RETRY.
There should be no functional changes cause by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add 'unsigned long dev_flags' to ide_drive_t and convert bitfields
to IDE_DFLAG_* flags.
While at it:
- IDE_DFLAG_ADDRESSING -> IDE_DFLAG_LBA48
- fixup some comments
- remove needless g->flags zeroing from ide*_probe()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_do_setfeature() helper and convert set_{wcache,acoustic}()
to use it.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Return -EIO if arg > 0 and LBA48 is unsupported.
* No need to reset ->addressing.
* Make ->addressing a single bit flag.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
... with which to control to verbosity of debug messages on module load time.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: no need to zero debug_mask + move module_param() closer debug_mask]
[bart: init drive->debug_mask in ide_floppy_probe() not in idefloppy_open()]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Also:
- leave in the possibility for optimizing away all debugging macros
- add a PFX macro and prepend all printk calls with it for consistency
- change idefloppy_create_rw_cmd's 1st arg from idefloppy_floppy_t * to
ide_drive_t *.
- add a missing printk-level in idefloppy_init
- fix minor checkpatch warnings
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Introduce to_ide_drv() and ide_drv_g() macros and replace the respective
definitions of similar ones in each driver.
There should be no functionality change resulting from this patch.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Because hd.c was moved to drivers/block/ this config option
is superfluous now and may be removed.
v2:
Fix drivers/ide/Makefile (noticed by Adrian Bunk).
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move ->ticks field from struct ide_floppy_obj to ide_drive_t.
* Move idefloppy_transfer_pc() to ide-atapi.c and make
ide_transfer_pc() use it.
* Always use ide_transfer_pc as a handler in ide_issue_pc().
* Remove no longer used idefloppy_start_pc_transfer(),
ide*_transfer_pc() and 'handler' argument from ide_issue_pc().
* Make ide_transfer_pc() static.
While at it:
* idefloppy_transfer_pc() -> ide_delayed_transfer_pc()
* IDEFLOPPY_TICKS_DELAY -> IDEFLOPPY_PC_DELAY
* ->ticks -> ->pc_delay
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Always use ide_pc_intr as a handler in ide_pc_intr().
* Remove no longer used ide*_pc_intr() and 'handler'
argument from ide_{transfer_pc,pc_intr}().
* Make ide_pc_intr() static.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->pc_{update,io}_buffers methods to ide_drive_t and use
them instead of {update,io}_buffers ide_pc_intr() arguments.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_create_request_sense_cmd() and ide_retry_pc() helpers
and convert ide-{atapi,floppy,tape}.c to use them.
* Remove no longer used ide*_create_request_sense_cmd(),
ide*_retry_pc() and 'retry_pc' argument from ide_pc_intr().
* Make ide_queue_pc_head() static.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add 'struct ide_atapi_pc request_sense_pc' and 'request request_sense_rq' to
ide_drive_t and use them instead of fields in struct ide_{floppy,tape}_obj.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move idescsi_expiry() to ide-atapi.c.
* Move get_timeout() to <linux/ide.h>.
* Drop 'timeout' and 'expiry' arguments from ide_pc_intr().
While at it:
* idescsi_expiry() -> ide_scsi_expiry()
* get_timeout() -> ide_scsi_get_timeout()
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add pointer to the current packet command (struct ide_atapi_pc *pc)
to ide_drive_t and use it instead of the pointer in struct ide_*_obj.
* Use drive->pc in ide_{issue,transfer}_pc() and ide_pc_intr()
instead of 'pc' argument.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'int dsc' argument to ->pc_callback method.
* Call ide_tape_handle_dsc() internally in ide_tape_callback()
if dsc argument is set and update ide_pc_intr() accordingly.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix several issues with the log messages printed by ide_dma_sgiioc4() and
sgiioc4_ide_setup_pci_device():
- IOC4 registers are memory-mapped but the "BM-DMA at" format corresponds to
I/O mapped registers;
- "%p" format specifiers and type casts used to print non-pointer values;
- using KERN_INFO log level for the error message;
- 'hwif->name' printed as drive's name.
While at it, also:
- return more fitting -EBUSY if request_mem_region() fails;
- make the error message style consistent;
- fix indentation, put the printk() facility and message on the same line;
- use comparisions with NULL instead of ! operator..
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: jeremy@sgi.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix the drive non-busy criterion used by sgiioc4_read_status(): neither of the
bits it expects to be set guarantees that the drive is not busy (and might be
interrupting), only the BSY bit itself being zero gurantees that.
While at it, use ATA_BUSY instead of hardcoded value everywhere...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: jeremy@sgi.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use a special request for serialisation purposes and get rid of the
awkward ide_spin_wait_hwgroup(). This also involves converting the
ide_devset structure so it can be shared by the /proc and the ioctl code.
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
[bart: use rq->cmd[] directly]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
While at it:
* IDE{FLOPPY,TAPE}_WAIT_CMD -> WAIT_{FLOPPY,TAPE}_CMD
* Use enum for WAIT_* defines.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_do_test_unit_ready() helper and convert ide-{floppy,tape}.c
to use it.
* Remove no longer used idetape_create_test_unit_ready_cmd().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_do_start_stop() helper and convert ide-{floppy,tape}.c
to use it.
* Remove no longer used idefloppy_create_start_stop_cmd()
and idetape_create_load_unload_cmd().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set IDE_AFLAG_NO_DOORLOCK in idetape_get_mode_sense_result(), check it
in ide_tape_set_media_lock() and cleanup idetape_create_prevent_cmd().
* Set IDE_AFLAG_NO_DOORLOCK in ide_floppy_create_read_capacity_cmd() and
check it instead of IDE_AFLAG_CLIK_DRIVE in ide_floppy_set_media_lock().
* Add ide_set_media_lock() helper and convert ide-{floppy,tape}.c to use it.
* Remove no longer used ide*_create_prevent_cmd()/ide*_set_media_lock().
* Update comment in <linux/ide.h> accordingly.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add IDE_AFLAG_{SRFP,WP} drive->atapi_flags and use them
instead of ->{srfp,wp} struct ide_floppy_obj fields.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_queue_pc_tail() and convert ide-{floppy,tape}.c to use it
instead of ide*_queue_pc_tail().
* Remove no longer used ide*_queue_pc_tail().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move REQ_IDETAPE_* enums to <linux/ide.h>.
* Add ide_queue_pc_head() and convert ide-{floppy,tape}.c to use it
instead of ide*_queue_pc_head().
* Remove no longer used ide*_queue_pc_head().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_PC_BUFFER_SIZE define.
* Add ide_init_pc() and convert ide-{floppy,tape}.c to use it
instead of ide*_init_pc().
* Remove no longer used IDE*_PC_BUFFER_SIZE and ide*_init_pc().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_tape_set_media_lock() helper and convert idetape_mtioctop(),
idetape_chrdev_open() and idetape_chrdev_release() to use it.
There should be no functional changes caused by this patch (it is
OK to modify ->door_locked if idetape_create_prevent_cmd() fails).
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_floppy_set_media_lock() helper and convert idefloppy_open(),
idefloppy_release() and ide_floppy_lockdoor() to use it.
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ->io_buffers method return number of bytes transferred.
* Use ide_end_request() instead of idefloppy_end_request()
in ide_floppy_io_buffers() and then move the call out to
ide_pc_intr().
* Add ide_io_buffers() helper and convert ide-{floppy,scsi}.c
to use it instead of ide*_io_buffers().
There should be no functional changes caused by this patch.
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Only MODE_SENSE_CURRENT (0x00) is ever used so just remove
these defines and then drop no longer needed 'type' argument
from idefloppy_create_mode_sense_cmd().
Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct ide_atapi_pc queued_pc' to struct ide_{floppy,tape}_obj
and switch ide*_do_request() to use it (there can be only one active
request for a given device).
* Add 'struct ide_atapi_pc request_sense_pc' to struct ide_*_obj
and switch ide*_retry_pc() to use it.
* Remove needless {floppy,tape}->pc assignment from ide*_setup().
* Remove no longer needed ide*_next_pc_storage(), pc_stack[],
rq_stack_index, IDE*_PC_STACK and DBG_PC_STACK.
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add 'struct request request_sense_rq' to struct ide_{floppy,tape}_obj
and switch ide*_retry_pc() to use it (there can be only one REQUEST SENSE
request active for a given device).
* Remove no longer needed ide*_next_rq_storage(), rq_stack[]
and rq_stack_index.
* DBG_PCRQ_STACK -> DBG_PC_STACK
* Update comments for IDE*_PC_STACK and idetape_queue_pc_{head,tail}().
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Avoid probing the io-ports in case an IDE PCI controller is present and it
uses the legacy iobases. If we still want to enforce the probing, we do
ide_generic.probe_mask=0x3f
on the kernel command line. The iobase checking code is
adapted from drivers/ata/pata_legacy.c after converting hex
pci ids into their corresponding macros in <linux/pci_ids.h>.
Also, check only BAR0/2 resources since those are guaranteed
by the workaround in drivers/pci/probe.c:pci_setup_device().
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
[bart: trivial printk() fixups]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use hwif->sg_table for pio transfers instead of fumbling
with block layer internals in the driver. Also, make debug
statements more informative in .._do_request() while at it.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
[bart: fixup pc->b_count in idefloppy_blockpc_cmd()]
[bart: add missing include (noticed by Stephen Rothwell)]
[bart: map hwif->sg_{table,nents} on pc->{sg,sg_cnt} (multi-IRQs-per-sg fix)]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
idetape_init_rq() is only used in idetape_queue_pc_head()
so inline it there.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out IDEFLOPPY_IOCTL_FORMAT_* ioctls handling from
idefloppy_ioctl() to ide_floppy_format_ioctl().
While at it:
* Pass 'drive' instead of 'floppy' to ide_floppy_format_unit().
* idefloppy_get_format_progress() -> ide_floppy_get_format_progress()
There should be no functional changes caused by this patch.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_check_atapi_device() to ide-atapi.c and convert
ide-{floppy,tape}.c to use it instead of ide*_identify_device().
While at it:
* Add DRV_NAME defines to ide-{floppy,tape}.c.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix intendation for the main 'switch ()'.
* 'switch ()' -> 'if ()' for HDIO_DRIVE_TASKFILE case.
* Move HDIO_SET_NICE case under HDIO_GET_NICE one.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add struct ide_ioctl_devset representing ioctl device setting.
* Add ide_setting_ioctl() helper for matching given ioctl
and its parameters against table of ioctl device settings.
* Convert ide_setting_ioctl() and idedisk_ioctl() to use
ide_setting_ioctl().
* Un-export ide_setting_mtx.
While at it:
* {get,set}_lba_addressing() -> {get,set}_addressing()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Keep pointer to ->init_chipset method also in
struct ide_host and set it in ide_host_alloc_all().
* Add ide_pci_suspend() and ide_pci_resume() helpers
(default ->suspend and ->resume implementations).
* ->init_chipset can no longer be marked __devinit.
* Add proper PCI PM support to IDE PCI host drivers
(rz1000.c and tc86c001.c are skipped for now since
they need to be converted from using ->init_hwif
to use ->init_chipset instead).
v2:
* Cleanup CONFIG_PM #ifdef-s per akpm's suggestion.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out disabling of "fast interrupt" prediction from
init_hwif_hpt366() to hpt3xx_disable_fast_irq() helper.
* Use hpt3xx_disable_fast_irq() in ->init_chipset instead of
->init_hwif method.
This is a preparation for adding proper PCI PM support.
While at it:
* Cache chip type in chip_type variable in hpt3xx_disable_fast_irq().
There should be no functional changes caused by this patch.
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Rename lba_capacity_is_ok() to ata_id_is_lba_capacity_ok()
and move it to <linux/ata.h> (remove needless parens while at it).
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Rename ide_id_to_hd_driveid() to ata_id_to_hd_driveid()
and move it to <linux/ata.h>.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ata_id_is_cfa() in do_identify() instead of open-coding
check for CompactFlash devices (the inline helper also takes
care of detecting CFs advertising themselves as ATA disks).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ata_id_flush_ext_enabled() inline helper to <linux/ata.h>.
* ide_id_has_flush_cache_ext() -> ata_id_flush_ext_enabled()
The latter one also checks if the command is marked as
supported in word 83 and validity of words 83 & 86.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ata_id_flush_enabled() inline helper to <linux/ata.h>.
* ide_id_has_flush_cache() -> ata_id_flush_enabled()
The latter one also checks if the command is marked as
supported in word 83 and validity of words 83 & 86.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ata_id_lba48_enabled() inline helper to <linux/ata.h>.
* idedisk_supports_lba48() -> ata_id_lba48_enabled()
The latter one also checks validity of words 83 & 86.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use optimized ATA version check from Sergei in ata_id_is_sata().
* ide_dev_is_sata() -> ata_id_is_sata()
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove (id[ATA_ID_FIELD_VALID] & 2) check from ide_dev_has_iordy()
(it is for validity of words 64-70, IORDY is in word 49).
* ide_dev_has_iordy() -> ata_id_has_iordy()
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out HDIO_{GET,SET}_NICE ioctl handling from
generic_ide_ioctl() to ide_{get,set}_nice_ioctl().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use drive->media and drive->scsi to check if ->dsc_overlap
can be set by HDIO_SET_NICE ioctl in generic_ide_ioctl().
* Remove unused ->supports_dsc_overlap field from ide_driver_t.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out the common code from check_prefetch()
and set_prefetch_mode() to __set_prefetch_mode().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add struct ide_devset, S_* flags, *DEVSET() & ide*_devset_*() macros.
* Add 'const struct ide_devset **settings' to ide_driver_t.
* Use 'const struct ide_devset **settings' in ide_drive_t instead of
'struct ide_settings_s *settings'. Then convert core code and device
drivers to use struct ide_devset and co.:
- device settings are no longer allocated dynamically for each device
but instead there is an unique struct ide_devset instance per setting
- device driver keeps the pointer to the table of pointers to its
settings in ide_driver_t.settings
- generic settings are kept in ide_generic_setting[]
- ide_proc_[un]register_driver(), ide_find_setting_by_name(),
ide_{read,write}_setting() and proc_ide_{read,write}_settings()
are updated accordingly
- ide*_add_settings() are removed
* Remove no longer used __ide_add_setting(), ide_add_setting(),
__ide_remove_setting() and auto_remove_settings().
* Remove no longer used TYPE_*, SETTING_*, ide_procset_t
and ide_settings_t.
* ->keep_settings, ->using_dma, ->unmask, ->noflush, ->dsc_overlap,
->nice1, ->addressing, ->wcache and ->nowerr ide_drive_t fields
can now be bitfield flags.
While at it:
* Rename ide_find_setting_by_name() to ide_find_setting().
* Rename write_wcache() to set_wcache().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After rework settings will be no longer created dynamically
for each device so we need to make some fixups first.
* Use set_[ksettings,unmaskirq]() as a set function for
["keepsettings","unmaskirq"] setting.
* Allow writes to ["io_32bit","unmaskirq"] settings also when
drive->no_[io_32bit,unmask] is set (this is checked later inside
set_[io_32bit,unmaskirq]() anywyay and keeps consistency with
the corresponding HDIO_SET_[32BIT,UNMASKINTR] ioctls).
* Use max possible multi sectors value (16) as an allowed max for
"multcount" setting. set_multcount() set function checks against
device's max possbile value anyway and it makes the proc setting
consistent with the corresponding HDIO_SET_MULTCOUNT ioctl.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Call ide_proc_register_driver() in ide*_setup() (just before
ide*_add_settings() call) instead of in ->probe method.
Despite being basically a preparation for /proc/ide/hd*/settings
rework this is a nice cleanup in itself.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Include <linux/ata.h> directly in <linux/ide.h>
instead of through <linux/hdreg.h>.
* Include <linux/hdreg.h> only when needed.
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use multi PIO by default when available and remove no longer
needed CONFIG_IDEDISK_MULTI_MODE (it should be safe nowadays,
despite to what help entry has been saying).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Change ide_get_paired_drive() to return NULL if peer device
is not present and update all users accordingly.
While at it:
* ide_get_paired_drive() -> ide_get_pair_dev()
* Use ide_get_pair_dev() in cs5530.c, sc1200.c and via82cxxx.c.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove needless drive->present checks from ->probe methods
(device model takes care of that).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
init_irq() is now called only during initial host registration
so these BUG_ON()-s are no loner needed (+ the last one was done
too late anyway).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_busy_sleep() take timeout value as a parameter
and also allow use of AltStatus Register if requested with
altstatus parameter. Update existing users accordingly.
* Convert ide_driveid_update() and actual_try_to_identify()
to use ide_busy_sleep().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix EXABYTENEST handling in probe_for_drive() (so drive->present
is checked for "nested" device) and cleanup enable_nest().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Friday 25 July 2008, Linus Torvalds wrote:
>
> On Fri, 25 Jul 2008, Ben Dooks wrote:
> >
> > personally, i would much prefer to see the loop being less evil
> > like:
> >
> > for (p = s; p < end; p += 2)
> > be16_to_cpus((u16 *)p);
>
> Well, in this case, the code actually depends on 'p' being back at the
> start of the buffer by the end of it all, so it would need some more
> changes than that.
>
> But yes, I applied David's patch, but I _also_ suspect that we would be
> better off without code that does horrid things like casts and assignments
> inside the function arguments.
>
> So it would be nice to re-code that loop to be more readable. But due to
> the reliance of 'p' being 's' after the loop, the minimal patch would be
> something like the appended.
>
> Bartlomiej - take this or not, I'm not going to commit it - I haven't
> tested it, nor do I even have any machines that would trigger it. So this
> is more a "maybe something like this" than anything else.
From: Linus Torvalds <torvalds@linux-foundation.org>
CC: Ben Dooks <ben-linux@fluff.org>
Cc: David Miller <davem@davemloft.net>
Cc: harvey.harrison@gmail.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ATA_CMD_* defines instead of WIN_* ones.
While at it:
* EXABYTE_ENABLE_NEXT -> ATA_EXABYTE_ENABLE_NEST
* SETFEATURES_{EN,DIS}_WCACHE -> SETFEATURES_WC_{ON,OFF}
* SETFEATURES_{EN,DIS}_AAM -> SETFEATURES_AAM_{ON,OFF}
* SMART_* -> ATA_SMART_*
* Remove stale comment from ide-proc.c.
Partially based on earlier work by Chris Wedgwood.
Acked-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
idedisk_supports_hpa() -> ata_id_hpa_enabled().
The latter one also checks validity of words 82 & 85.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace open-coded check by ata_id_wcache_enabled()
(which also checks validity of word 85).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace open-coded checks by ata_id_current_chs_valid().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out HDIO_[OBSOLETE,GET]_IDENTITY ioctls handling
to ide_get_identity_ioctl().
* Use temporary buffer in ide_get_identity_ioctl() instead
of accessing drive->id directly.
* Add ide_id_to_hd_driveid() inline to convert raw id into
struct hd_driveid format (needed on big-endian).
* Use ide_id_to_hd_driveid() in ide_get_identity_ioctl(),
cleanup ide_fix_driveid() and switch ide to use use raw id.
* Remove no longer needed drive->driveid.
This leaves us with 3 users of struct hd_driveid in tree:
- arch/um/drivers/ubd_kern.c
- drivers/block/xsysace.c
- drivers/usb/storage/isd200.c
While at it:
* Use ata_id_u{32,64}() and ata_id_has_{dma,lba,iordy}() macros.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make drive->id an unnamed union so id can be accessed either by using
'u16 *id' or 'struct hd_driveid *driveid'. Then convert all existing
drive->id users accordingly (using 'u16 *id' when possible).
This is an intermediate step to make ide 'struct hd_driveid'-free.
While at it:
- Add missing KERN_CONTs in it821x.c.
- Use ATA_ID_WORDS and ATA_ID_*_LEN defines.
- Remove unnecessary checks for drive->id.
- s/drive_table/table/ in ide_in_drive_list().
- Cleanup ide_config_drive_speed() a bit.
- s/drive1/dev1/ & s/drive0/dev0/ in ide_undecoded_slave().
v2:
Fix typo in drivers/ide/ppc/pmac.c. (From Stephen Rothwell)
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove superfluous checks for drive->mult_req.
* No need to zero drive's fields.
* Move the common code out of #ifdef scope.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This condition is checked by both ide_disk_init_mult_count()
and set_multcount() so no need to do it again in ide_disk_special().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The format specifier for rq->sector didn't specify the proper size and
signedness. Borislav Petkov discovered that the signedness for
rq->nr_sectors and rq->current_nr_sectors also were incorrect.
Signed-off-by: Mark de Wever <koraq@xs4all.nl>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
[bart: remove trailing whitespace]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Now that disk and partition handlings are mostly unified, it's easy to
allow disk to have extended device number. This patch makes
add_disk() use extended device number if disk->minors is zero. Both
sd and ide-disk are updated to use this.
* sd_format_disk_name() is implemented which can generically determine
the drive name. This removes disk number restriction stemming from
limited device names.
* If sd index goes over SD_MAX_DISKS (which can be increased now BTW),
sd simply doesn't initialize minors letting block layer choose
extended device number.
* If CONFIG_DEBUG_EXT_DEVT is set, both sd and ide-disk always set
minors to 0 and use extended device numbers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With previous changes, it's meaningless to limit the number of
partitions. Replace @ext_minors with GENHD_FL_EXT_DEVT such that
setting the flag allows the disk to have maximum number of allowed
partitions (only limited by the number of entries in parsed_partitions
as determined by MAX_PART constant).
This kills not-too-pretty alloc_disk_ext[_node]() functions and makes
@minors parameter to alloc_disk[_node]() unnecessary. The parameter
is left alone to avoid disturbing the users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Implement {disk|part}_to_dev() and use them to access generic device
instead of directly dereferencing {disk|part}->dev. To make sure no
user is left behind, rename generic devices fields to __dev.
This is in preparation of unifying partition 0 handling with other
partitions.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Extended devt introduces non-contiguos device numbers. This patch
implements a debug option which forces most devt allocations to be
from the extended area and spreads them out. This is enabled by
default if DEBUG_KERNEL is set and achieves...
1. Detects code paths in kernel or userland which expect predetermined
consecutive device numbers.
2. When something goes wrong, avoid corruption as adding to the minor
of earlier partition won't lead to the wrong but valid device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Update sd and ide-disk such that they can take advantage of extended
minors.
ide-disk already has 64 minors per device and currently doesn't use
extended minors although after this patch it can be turned on by
simply tweaking constants.
sd only had 16 minors per device causing problems on certain peculiar
configurations. This patch lifts the restriction and enables it to
use upto 64 minors.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The Optiarc DVD RW AD-7200A can play audio, but tells it could not.
Signed-off-by: Bodo Eggert <7eggert@gmx.de>
Tested-by: Nick Warne <nick@ukfsn.org>
Received-from: Borislav Petkov <petkovbb@googlemail.com>
[bart: keep "audio" quirks together]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The Swarm IDE driver uses a release method which is defined in the driver
itself thus potentially oopsable. The simple fix would be to just leak
the device but this patch goes the full length and moves the entire
handling of the platform device in the platform code and retains only
the platform driver code in drivers/ide/mips/swarm.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove no longer needed BLK_DEV_IDE_SWARM from ide/Kconfig]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Apparently, 'xcount' being 0 does not mean 0 bytes for TRM290; it means 4 bytes,
judging from the code immediately preceding this check. So, we must never try
to "split" the PRD for TRM290.
This is probably never hit anyway -- with the DMA buffers aligned to at least
512 bytes and ATAPI DMA not being used for non block I/O commands...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This one fixes http://bugzilla.kernel.org/show_bug.cgi?id=11602.
A more generic fix for drives which cannot autoclose tray will follow.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
[bart: add an extra parentheses for consistency with the rest of kernel code]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Enabling IDE generic may prevent ATA controllers located on legacy
ports from being attached to more proper driver or can prevent other
controllers which share the IRQ from working. Note it in the help
message.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: xerces8 <xerces8@butn.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: stein@hermes.si
[bart: s/will grab/may grab/ since Borislav has fixed PCI-case for .28]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove superfluous two bytes from each string buffer and add proper length
format specifiers.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Tested-by: Mark de Wever <koraq@xs4all.nl>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If things are just right this will result in the hws[0]->parent being
passed to ide_host_add() being non-zero and an ooops a little later.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We still have life time issues with the sysfs command filter kobject,
so disable it for 2.6.27 release. We can revisit this and make it work
properly for 2.6.28, for 2.6.27 release it's too risky.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
git commit 74811f355f causes crash at
module load (or boot) time on my machine with a hpt374 controller.
The reason for this is that for initializing second controller which sets
(hwif->dev == host->dev[1]) to true (1), adds 1 to a void ptr, which
advances it by one byte instead of advancing it by sizeof(hpt_info) bytes.
Because of this, all initialization functions get corrupted data in info
variable which causes a crash at boot time.
This patch fixes that and makes my machine boot again.
The card itself is a HPT374 raid conroller: Here is the lspci -v output:
03:06.0 RAID bus controller: HighPoint Technologies, Inc. HPT374 (rev
07)
Subsystem: HighPoint Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 28
I/O ports at 8000 [size=8]
I/O ports at 7800 [size=4]
I/O ports at 7400 [size=8]
I/O ports at 7000 [size=4]
I/O ports at 6800 [size=256]
Expansion ROM at fe8e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
03:06.1 RAID bus controller: HighPoint Technologies, Inc. HPT374 (rev
07)
Subsystem: HighPoint Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 28
I/O ports at 9800 [size=8]
I/O ports at 9400 [size=4]
I/O ports at 9000 [size=8]
I/O ports at 8800 [size=4]
I/O ports at 8400 [size=256]
Capabilities: [60] Power Management version 2
Signed-off-by: Masoud Sharbiani <masouds@google.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
[bart: use dev_get_drvdata() per Sergei's suggestion]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* fix device tree ... don't forget to set the parent device
* let init/exit code be removed where practical
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
[bart: splitted it from bigger DaVinci patch, s/hw.parent/hw.dev/]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
