mirror of
https://github.com/AuxXxilium/linux_dsm_epyc7002.git
synced 2024-12-28 11:18:45 +07:00
a27415decd
1412 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Andrew Lunn
|
a27415decd |
net: dsa: mv88e6xxx: Pass interrupt number in platform data
Allow an interrupt number to be passed in the platform data. The driver will then use it if not zero, otherwise it will poll for interrupts. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Nicolas Ferre
|
8b95274784 |
net: macb: shrink macb_platform_data structure
This structure was used intensively for machine specific values when DT was not used. Since the removal of AVR32 from the kernel, this structure is only used for passing clocks from PCI macb wrapper, all other fields being 0. All other known platforms use DT. Remove the leftovers but make sure that PCI macb still works as expected by using default values: - phydev->irq is set to PHY_POLL by mdiobus_alloc() - mii_bus->phy_mask is cleared while allocating it - bp->phy_interface is set to PHY_INTERFACE_MODE_MII if mode not found in DT. This simplifies driver probe path and particularly phy handling. Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Esben Haabendal
|
7e97a194ac |
net: ll_temac: Allow configuration of IRQ coalescing
This allows custom setup of IRQ coalescing for platforms using legacy platform_device. The irq timeout and count parameters can be used for tuning cpu load vs. latency. I have maintained the 0x00000400 bit in TX_CHNL_CTRL. It is specified as unused in the documentation I have available. It does not make any difference in the hardware I have available, so it is left in to not risk breaking other platforms where it might be used. Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Esben Haabendal
|
f14f5c11f0 |
net: ll_temac: Support indirect_mutex share within TEMAC IP
Indirect register access goes through a DCR bus bridge, which allows only one outstanding transaction. And to make matters worse, each TEMAC IP block contains two Ethernet interfaces, and although they seem to have separate registers for indirect access, they actually share the registers. Or to be more specific, MSW, LSW and CTL registers are physically shared between Ethernet interfaces in same TEMAC IP, with RDY register being (almost) specificic to the Ethernet interface. The 0x10000 bit in RDY reflects combined bus ready state though. So we need to take care to synchronize not only within a single device, but also between devices in same TEMAC IP. This commit allows to do that with legacy platform devices. For OF devices, the xlnx,compound parent of the temac node should be used to find siblings, and setup a shared indirect_mutex between them. I will leave this work to somebody else, as I don't have hardware to test that. No regression is introduced by that, as before this commit using two Ethernet interfaces in same TEMAC block is simply broken. Signed-off-by: Esben Haabendal <esben@geanix.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Esben Haabendal
|
a3246dc41a |
net: ll_temac: Add support for non-native register endianness
Replace the powerpc specific MMIO register access functions with the generic big-endian mmio access functions, and add support for little-endian access depending on configuration. Big-endian access is maintained as the default, but little-endian can be configured in device-tree binding or in platform data. The temac_ior()/temac_iow() functions are replaced with macro wrappers to avoid modifying existing code more than necessary. Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Esben Haabendal
|
8425c41d1e |
net: ll_temac: Extend support to non-device-tree platforms
Support initialization with platdata, so the driver can be used on non-device-tree platforms. For currently supported device-tree platforms, the driver should behave as before. Signed-off-by: Esben Haabendal <esben@geanix.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Linus Torvalds
|
09bad0df39 |
Here's more than a handful of clk driver fixes for changes that came in
during the merge window:
- Fix the AT91 sama5d2 programmable clk prescaler formula
- A bunch of Amlogic meson clk driver fixes for the VPU clks
- A DMI quirk for Intel's Bay Trail SoC's driver to properly mark
pmc clks as critical only when really needed
- Stop overwriting CLK_SET_RATE_PARENT flag in mediatek's clk gate
implementation
- Use the right structure to test for a frequency table in i.MX's
PLL_1416x driver
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAlyxC/IRHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSWPTg//Q9CXbOYC64u2LEMtMKFtxS0UobjFKyMg
EfRnHM3EuRKHCSPLtcr5bKQkFQYJ7Qx9A8oQm4v1d0KlQ2HyrOuAjfAkCaKweKSK
iXpvWQMHcyRNPmPhzaDnuGBVXptOQ+kfwjWT4/nbkjW0bnFTwpvx9I5pdUd3UOJv
IdnYOLKAF8Uwt2nyJd++Bh0UeBhQ1XIl9P46iZGa43nQsQhgSaru3oBnhVOzEti/
k9Di3H1k1wIKR+xDujl/S3vIIEUcx0eGkL86sFdVq6nYwdQQZKusESC0vh5QJ/Ax
LLSJcdoM8B84zStkYgIskdltdMZmsUUjLjjEbF5iq1my+LwQZ3JLWkY/gXMeF2Mu
t5S/TVe5GwqKw2tmoQYkR2Qz76x7/DauZEdUcYtu+K9D2ye5aNDsNNCHlFkamN2N
EJkBXDqpKGHkyOdUGmL+B0W6D1KxwJEREkCh0aIpbVci1PjfxvI6PLJBF907RkLx
UNDF/flLoOMy+iUl0ZC05Ie06CkzJMf1e7mMaIIS/FfC7UJ4yNVEHyCADzyrCLOB
XWwmwCea5NnIi3EQP91a7WO/Gr+yUWxfrQ3viNqM3KbPKOurofMp/JvDnu8bX31O
l+yiRfpdjIaKUdyDLnTaq3UGBlBlFnqFOWkjRmmMzRZoBmwZhCN7H30LIlqnqnpQ
wsvhawe24UY=
=JS0o
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Here's more than a handful of clk driver fixes for changes that came
in during the merge window:
- Fix the AT91 sama5d2 programmable clk prescaler formula
- A bunch of Amlogic meson clk driver fixes for the VPU clks
- A DMI quirk for Intel's Bay Trail SoC's driver to properly mark pmc
clks as critical only when really needed
- Stop overwriting CLK_SET_RATE_PARENT flag in mediatek's clk gate
implementation
- Use the right structure to test for a frequency table in i.MX's
PLL_1416x driver"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx: Fix PLL_1416X not rounding rates
clk: mediatek: fix clk-gate flag setting
platform/x86: pmc_atom: Drop __initconst on dmi table
clk: x86: Add system specific quirk to mark clocks as critical
clk: meson: vid-pll-div: remove warning and return 0 on invalid config
clk: meson: pll: fix rounding and setting a rate that matches precisely
clk: meson-g12a: fix VPU clock parents
clk: meson: g12a: fix VPU clock muxes mask
clk: meson-gxbb: round the vdec dividers to closest
clk: at91: fix programmable clock for sama5d2
|
||
|
David Müller
|
7c2e071300 |
clk: x86: Add system specific quirk to mark clocks as critical
Since commit |
||
|
Thomas Gleixner
|
b45a02e13e |
gpio: amd-fch: Fix bogus SPDX identifier
spdxcheck.py complains:
include/linux/platform_data/gpio/gpio-amd-fch.h: 1:28 Invalid License ID: GPL+
which is correct because GPL+ is not a valid identifier. Of course this
could have been caught by checkpatch.pl _before_ submitting or merging the
patch.
WARNING: 'SPDX-License-Identifier: GPL+ */' is not supported in LICENSES/...
#271: FILE: include/linux/platform_data/gpio/gpio-amd-fch.h:1:
+/* SPDX-License-Identifier: GPL+ */
Fix it under the assumption that the author meant GPL-2.0+, which makes
sense as the corresponding C file is using that identifier.
Fixes:
|
||
|
Linus Torvalds
|
31ef489a02 |
dmaengine updates for v5.1-rc1
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers
multi-block support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
-----BEGIN PGP SIGNATURE-----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=Ykvn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- dmatest updates for modularizing common struct and code
- remove SG support for VDMA xilinx IP and updates to driver
- Update to dw driver to support Intel iDMA controllers multi-block
support
- tegra updates for proper reporting of residue
- Add Snow Ridge ioatdma device id and support for IOATDMA v3.4
- struct_size() usage and useless LIST_HEAD cleanups in subsystem.
- qDMA controller driver for Layerscape SoCs
- stm32-dma PM Runtime support
- And usual updates to imx-sdma, sprd, Documentation, fsl-edma,
bcm2835, qcom_hidma etc
* tag 'dmaengine-5.1-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (81 commits)
dmaengine: imx-sdma: fix consistent dma test failures
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
dmaengine: imx-sdma: add clock ratio 1:1 check
dmaengine: dmatest: move test data alloc & free into functions
dmaengine: dmatest: add short-hand `buf_size` var in dmatest_func()
dmaengine: dmatest: wrap src & dst data into a struct
dmaengine: ioatdma: support latency tolerance report (LTR) for v3.4
dmaengine: ioatdma: add descriptor pre-fetch support for v3.4
dmaengine: ioatdma: disable DCA enabling on IOATDMA v3.4
dmaengine: ioatdma: Add Snow Ridge ioatdma device id
dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dt-bindings: dmaengine: sprd: Change channel id to slave id for DMA cell specifier
dmaengine: mv_xor: Use correct device for DMA API
Documentation :dmaengine: clarify DMA desc. pointer after submission
Documentation: dmaengine: fix dmatest.rst warning
dmaengine: k3dma: Add support for dma-channel-mask
dmaengine: k3dma: Delete axi_config
dmaengine: k3dma: Upgrade k3dma driver to support hisi_asp_dma hardware
Documentation: bindings: dma: Add binding for dma-channel-mask
Documentation: bindings: k3dma: Extend the k3dma driver binding to support hisi-asp
...
|
||
|
Linus Torvalds
|
dc2535be1f |
We have a fairly balanced mix of clk driver updates and clk framework
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional() API
to get clks that may not always be populated and a way to devm manage clkdev
lookups registered by provider drivers. We also do some refactoring to simplify
the interface between clkdev and the common clk framework so we can reuse the DT
parsing and clk_get() path in provider drivers in the future. This work will
continue in the next few cycles while we convert how providers specify clk
parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk driver
that got support for the G12A SoC. It dominates with almost half the overall
diff, while the second largest part of the diff is in the i.MX clk driver
that gained support for imx8mm SoCs. After that, we have the Actions Semiconductor
and Qualcomm drivers rounding out the big part of the dirstat because they both
got new hardware support for SoCs. The rest is just various updates and non-critical
fixes for existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support
-----BEGIN PGP SIGNATURE-----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=D4Bv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"We have a fairly balanced mix of clk driver updates and clk framework
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional()
API to get clks that may not always be populated and a way to devm
manage clkdev lookups registered by provider drivers. We also do some
refactoring to simplify the interface between clkdev and the common
clk framework so we can reuse the DT parsing and clk_get() path in
provider drivers in the future. This work will continue in the next
few cycles while we convert how providers specify clk parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk
driver that got support for the G12A SoC. It dominates with almost
half the overall diff, while the second largest part of the diff is in
the i.MX clk driver that gained support for imx8mm SoCs. After that,
we have the Actions Semiconductor and Qualcomm drivers rounding out
the big part of the dirstat because they both got new hardware support
for SoCs. The rest is just various updates and non-critical fixes for
existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
dt-bindings: clock: imx8mq: Fix numbering overlaps and gaps
clk: ti: clkctrl: Fix clkdm_name regression for TI_CLK_CLKCTRL_COMPAT
clk: fixup default index for of_clk_get_by_name()
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
clk: imx8mq: add GPIO clocks to clock tree
clk: mediatek: correct cpu clock name for MT8173 SoC
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: mediatek: Mark bus and DRAM related clocks as critical
clk: mediatek: Add flags to mtk_gate
clk: mediatek: Add MUX_FLAGS macro
clk: qcom: gcc-sdm845: Define parent of PCIe PIPE clocks
clk: ingenic: Remove set but not used variable 'enable'
clk: at91: programmable: remove unneeded register read
clk: mediatek: using CLK_MUX_ROUND_CLOSEST for the clock of dpi1_sel
clk: mediatek: add MUX_GATE_FLAGS_2
...
|
||
|
Linus Torvalds
|
f47d633134 |
chrome platform changes for v5.1
1. SPDX identifier cleanup for platform/chrome
2. Cleanup series between mfd and chrome/platform, moving
cros-ec attributes from mfd/cros_ec_dev to sub-drivers in platform/chrome.
3. Wilco EC driver
4. Maintainership change to new group repository.
-----BEGIN PGP SIGNATURE-----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=2nC0
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
- SPDX identifier cleanup for platform/chrome
- Cleanup series between mfd and chrome/platform, moving cros-ec
attributes from mfd/cros_ec_dev to sub-drivers in platform/chrome
- Wilco EC driver
- Maintainership change to new group repository
* tag 'tag-chrome-platform-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: fix wilco-ec dependencies
platform/chrome: wilco_ec: Add RTC driver
platform/chrome: wilco_ec: Add support for raw commands in debugfs
platform/chrome: Add new driver for Wilco EC
platform/chrome: cros_ec: Remove cros_ec dependency in lpc_mec
MAINTAINERS: chrome-platform: change the git tree to a chrome-platform group git tree
platform/chrome: cros_ec_sysfs: remove pr_fmt() define
platform/chrome: cros_ec_lightbar: remove pr_fmt() define
platform/chrome: cros_kbd_led_backlight: switch to SPDX identifier
platform/chrome: cros_ec_spi: switch to SPDX identifier
platform/chrome: cros_ec_proto: switch to SPDX identifier
platform/chrome: cros_ec_lpc: switch to SPDX identifier
platform/chrome: cros_ec_i2c: switch to SPDX identifier
platform/chrome: cros_ec_vbc: switch to SPDX identifier
platform/chrome: cros_ec_sysfs: switch to SPDX identifier
platform/chrome: cros_ec_lightbar: switch to SPDX identifier
platform/chrome: cros_ec_debugfs: switch to SPDX identifier
platform/chrome: cromeos_pstore: switch to SPDX identifier
|
||
|
Vinod Koul
|
278489c2e1 | Merge branch 'topic/dw' into for-linus | ||
|
Linus Torvalds
|
a089e4fed5 |
linux-watchdog 5.1-rc1 tag
-----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.14 (GNU/Linux) iEYEABECAAYFAlyFIfgACgkQ+iyteGJfRsqt4gCgrgwSrDhwW+u7NjyY48KGAPgt xM8AoM31H9C2HrT2IJuKa3FjIawceUfw =wj0o -----END PGP SIGNATURE----- Merge tag 'linux-watchdog-5.1-rc1' of git://www.linux-watchdog.org/linux-watchdog Pull watchdog updates from Wim Van Sebroeck: - a new watchdog driver for the Mellanox systems - renesas-wdt: Document r8a77470 support - numerous 'Mark expected switch fall-throughs' - qcom: Add suspend/resume support - some small fixes and documentation updates * tag 'linux-watchdog-5.1-rc1' of git://www.linux-watchdog.org/linux-watchdog: watchdog: w83877f_wdt: Mark expected switch fall-through watchdog: sc520_wdt: Mark expected switch fall-through watchdog: sbc60xxwdt: Mark expected switch fall-through watchdog: smsc37b787_wdt: Mark expected switch fall-through watchdog: sc1200: Mark expected switch fall-through watchdog: pc87413: Mark expected switch fall-through Documentation/watchdog: Add documentation mlx-wdt driver watchdog: mlx-wdt: introduce a watchdog driver for Mellanox systems. platform_data/mlxreg: additions for Mellanox watchdog driver. watchdog: Update sysfs documentation. watchdog: dw: remove useless pr_fmt watchdog: pika_wdt: drop pointless static qualifier in pikawdt_init watchdog/hpwdt: Update Kconfig documentation dt-bindings: watchdog: renesas-wdt: Document r8a77470 support watchdog: qcom: Add suspend/resume support |
||
|
Linus Torvalds
|
dbbdf54c72 |
platform-drivers-x86 for v5.1-1
Use MODULE_DEVICE_TABLE across several wmi drivers, keeping wmi_device_id and MODULE_ALIAS() declarations in sync. Add several Ideapad models to the no_hw_rfkill list. Add support for new Mellanox platforms, including new fan and LED functionality. Address Dell keyboard backlight change event and power button release issues. Update dell_rbu to use appropriate memory allocation mechanisms. Several small fixes and Ice Lake support for intel_pmc_core. Fix a suspend regression for Cherry Trail based devices in intel_int0002_vgpio. A few other routine fixes. The following is an automated git shortlog grouped by driver: ACPI / scan: - Create platform device for BSG2150 ACPI nodes Documentation/ABI: - Add new attribute for mlxreg-io sysfs interfaces - Correct mlxreg-io KernelVersion for 5.0 MAINTAINERS: - Include mlxreg.h in Mellanox Platform Driver files asus-wmi: - Allow loading on systems without the Asus Management GUID dell-smbios-wmi: - use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() dell-wmi: - use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() - Ignore new keyboard backlight change event dell-wmi-descriptor: - use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() dell_rbu: - fix lock imbalance in img_update_realloc - stop abusing the DMA API huawei-wmi: - use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() ideapad-laptop: - Add ideapad 330-15ICH to no_hw_rfkill - Add S130-14IGM to no_hw_rfkill list - Add Ideapad 530S-14ARR to no_hw_rfkill list - Add Yoga C930 to no_hw_rfkill_list - Add Y530-I5ICH-1060 to no_hw_rfkill list - Fix no_hw_rfkill_list for Lenovo RESCUER R720-15IKBN intel-hid: - Missing power button release on some Dell models intel-wmi-thunderbolt: - use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() intel_int0002_vgpio: - Only implement irq_set_wake on Bay Trail intel_pmc_core: - Quirk to ignore XTAL shutdown - Add Package cstates residency info - Add ICL platform support - Convert to INTEL_CPU_FAM6 macro - Avoid a u32 overflow - Include Reserved IP for LTR - Fix file permissions for ltr_show - Fix PCH IP name - Fix PCH IP sts reading - Handle CFL regmap properly leds: - mlxreg: Add support for capability register mlx-platform: - Fix access mode for fan_dir attribute - Add UID LED for the next generation systems - Add extra CPLD for next generation systems - Add support for new VMOD0007 board name - Add support for fan capability registers - Add support for fan direction register modpost: - file2alias: define size of alias platform/mellanox: - mlxreg-hotplug: Fix KASAN warning platform_data/mlxreg: - Add capability field to core platform data - Document fixes for core platform data touchscreen_dmi: - Add info for the CHUWI Hi10 Air tablet - Add info for the Chuwi Hi8 Air tablet - Add info for the PoV Wintab P1006w (v1.0) tablet wmi: - add WMI support to MODULE_DEVICE_TABLE() - move struct wmi_device_id to mod_devicetable.h - fix potential null pointer dereference wmi-bmof: - use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() x86/CPU: - Add Icelake model number -----BEGIN PGP SIGNATURE----- iQEzBAABCAAdFiEE9M1dh6j+oEL41EZIXFIlAfdBhuEFAlyCu1EACgkQXFIlAfdB huFASAf/d0Y6uqhLD3G7cL2kXjOWoTE9ouWUwv19bBpnohGmD3OMMap4y1lb6nRR thCJRhpmX4ObS2adAC4otiOxTzmVoYGsuS9kfBwhKIby2VYHCCxxaTUs6bzMdOfV GsbaMA+vfb29bU4DcWlRtYZIz2FC5oyjW4ZmcMA6KtuBGjG9K1fG5zANQe4H8I0e zCdcrXhpDGIBJgaJR2N42EUCJruPoEXYfHa1G4B/QKvuW0CXHAdSE0YrN4ju+S3e Ew9ZXhoxRaqlu+ZB7H5Kyy6Mg3ZGMzbeYyQFLk5f2yiKSTFNiqwTEJl1aE2JSpy3 g8Im+6E44/4G8QOL40g5XwmrxHw5mA== =Bx4o -----END PGP SIGNATURE----- Merge tag 'platform-drivers-x86-v5.1-1' of git://git.infradead.org/linux-platform-drivers-x86 Pull x86 platform driver updates from Darren Hart: - use MODULE_DEVICE_TABLE across several wmi drivers, keeping wmi_device_id and MODULE_ALIAS() declarations in sync - add several Ideapad models to the no_hw_rfkill list - add support for new Mellanox platforms, including new fan and LED functionality - address Dell keyboard backlight change event and power button release issues - update dell_rbu to use appropriate memory allocation mechanisms - several small fixes and Ice Lake support for intel_pmc_core - fix a suspend regression for Cherry Trail based devices in intel_int0002_vgpio - a few other routine fixes * tag 'platform-drivers-x86-v5.1-1' of git://git.infradead.org/linux-platform-drivers-x86: (50 commits) MAINTAINERS: Include mlxreg.h in Mellanox Platform Driver files platform/x86: ideapad-laptop: Add S130-14IGM to no_hw_rfkill list platform/x86: mlx-platform: Fix access mode for fan_dir attribute platform/x86: mlx-platform: Add UID LED for the next generation systems platform/x86: mlx-platform: Add extra CPLD for next generation systems platform/x86: wmi-bmof: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() platform/x86: intel-wmi-thunderbolt: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() platform/x86: huawei-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() platform/x86: dell-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() platform/x86: dell-wmi-descriptor: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() platform/x86: dell-smbios-wmi: use MODULE_DEVICE_TABLE() instead of MODULE_ALIAS() platform/x86: wmi: add WMI support to MODULE_DEVICE_TABLE() platform/x86: wmi: move struct wmi_device_id to mod_devicetable.h modpost: file2alias: define size of alias platform/x86: touchscreen_dmi: Add info for the CHUWI Hi10 Air tablet platform/x86: ideapad-laptop: Add Ideapad 530S-14ARR to no_hw_rfkill list platform/x86: ideapad-laptop: Add Yoga C930 to no_hw_rfkill_list platform/x86: intel_pmc_core: Quirk to ignore XTAL shutdown platform/x86: intel_pmc_core: Add Package cstates residency info platform/x86: intel_pmc_core: Add ICL platform support ... |
||
|
Linus Torvalds
|
96a6de1a54 |
media updates for v5.1-rc1
-----BEGIN PGP SIGNATURE----- iQIcBAABAgAGBQJcgUDlAAoJEAhfPr2O5OEV2kIP/AiHMkMGi/fXmwzN0tFjYkim 39t6rodj6rT/oMib4XvW55GjQy5sdXwz+1jE+kZA5imbUvt6YzUXFBzIBOGOIF0n 1MukKa7M6ragnm2yR+42ucBr3jcuc91/keeVzWgP2cgeZeKUlBHme+rECYnwqDdT 9rcG4U2XL0Wolbm4lAispaWYIYoOURvPeryJ244vlPmch5/2nmXbG7AgNlfJsAw4 NFmdHBWxLeyB8F95ToikhuNlTWrsvdVHPHbDaDPwioSulZ1vw+lu4CHRd1uZo2iH W0INE65ukgyenzTDbmnj5/oWCqV4KRTs8A2x6eimz+wG/60jWQjDiBLSzhxjBH7x alrwhxnW3bD31ZUCkmaGd1+3txvLf+Lup9lLX3GCBKA45dW9pzVCLfxSfNaKKlTL 0xCYSMxl5xbl8TL6hHxK7/n+LsButgTRWIoJpqkM9uPrljwzznpgqJvARqSuHEKJ 3Tvnkc2DZsmlM8L02i929BsrsoTncm6wBBVlCJzhL0VNaOuL7yJVzXhrw7b/dZZw IZu6cH5RrZhIQR4y1UPlaEZoidUGvR0+K997AsURIHJA0RolWE5eI2JHSE86EX8S bzG5SChkQmbpYt5OXQvg5VxvqVElx/5/tamcHe/rKwaAwaG9aI9HICgP2e0Zaoce YOMJUpcHtSY5Fedk8P1a =tD1x -----END PGP SIGNATURE----- Merge tag 'media/v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media Pull media updates from Mauro Carvalho Chehab: - remove sensor drivers that got converted from soc_camera - remaining soc_camera drivers got moved to staging - some documentation cleanups and improvements - the imx staging driver now supports imx7 - the ov9640, mt9m001 and mt9m111 got converted from soc_camera - the vim2m driver now does what a m2m convert driver expects to do - epoll() fixes on media subsystems - several drivers fixes, typos, cleanups and improvements * tag 'media/v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (346 commits) media: dvb/earth-pt1: fix wrong initialization for demod blocks media: vim2m: Address some coding style issues media: vim2m: don't use BUG() media: vim2m: speedup passthrough copy media: vim2m: add an horizontal scaler media: vim2m: don't accept YUYV anymore as output format media: vim2m: add vertical linear scaler media: vim2m: better handle cap/out buffers with different sizes media: vim2m: use different framesizes for bayer formats media: vim2m: add support for VIDIOC_ENUM_FRAMESIZES media: vim2m: ensure that width is multiple of two media: vim2m: improve debug messages media: vim2m: add bayer capture formats media: a few more typos at staging, pci, platform, radio and usb media: Documentation: fix several typos media: staging: fix several typos media: include: fix several typos media: common: fix several typos media: v4l2-core: fix several typos media: usb: fix several typos ... |
||
|
Linus Torvalds
|
3601fe43e8 |
This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in
the qualcomm pin controllers, closely coupled with the
gpiochip. This rework, in a classic fall-between-the-chairs
fashion has been sidestepped for too long. The Qualcomm
IRQchips using the SPMI and SSBI transport mechanisms have
been rewritten to use hierarchical irqchip. This creates
the base from which I intend to gradually pull support for
hierarchical irqchips into the gpiolib irqchip helpers to
cut down on duplicate code. We have too many hacks in the
kernel because people have been working around the missing
hierarchical irqchip for years, and once it was there,
noone understood it for a while. We are now slowly adapting
to using it. This is why this pull requests include changes
to MFD, SPMI, IRQchip core and some ARM Device Trees
pertaining to the Qualcomm chip family. Since Qualcomm have
so many chips and such large deployments it is paramount
that this platform gets this right, and now it (hopefully)
does.
- Core support for pull-up and pull-down configuration, also
from the device tree. When a simple GPIO chip support a
"off or on" pull-up or pull-down resistor, we provide a
way to set this up using machine descriptors or device tree.
If more elaborate control of pull up/down (such as
resistance shunt setting) is required, drivers should be
phased over to use pin control. We do not yet provide a
userspace ABI for this pull up-down setting but I suspect
the makers are going to ask for it soon enough. PCA953x
is the first user of this new API.
- The GPIO mockup driver has been revamped after some
discussion improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for
both testing and virtual prototyping, e.g. when you do
not yet have a GPIO expander to play with but really
want to get something to develop code around before
hardware is available. It's neat. The blackbox testing
usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating
flags.
- A new device core helper for devm_platform_ioremap_resource()
is funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped
I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum
driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcgoLEAAoJEEEQszewGV1zjBAP/3OmTFGv49PFmJwSx+PlLiYf
V6/UPaQzq81CGSMtHxbS51TyP9Id7PCfsacbuFYutzn0D1efvl7jrkb8qJ6fVvCM
bl/i6q8ipRTPzAf1hD3QCgCe3BXCA064/OcPrz987oIvI3bJQXsmBjBSXHWr4Cwa
WfB5DX/afn9TK3XHhMQGfw5f0d+TtnKAs90RTTVKiz9Ow8eFYZJOhgPkvhCR3Gi9
YJIzIAiwhHZ7/zauo4JAYFU/O/Z3YEC5zeLne2ItebzNooRkSxdz0c9Hs7HlCZmU
930Uv9jNN89N3vPqpZzAHtPvwDOmAILMWvKy9xRSp+eoIukarRJgF7ALPk7QWxK1
yy+tGj4dXBQ6tI8W3wUN1WgjNpii3K1HbJ+1LQVQL2/q9o+3YXXqmjdjuw7C8YYV
5ystNrUppkgfIIciHL4lhqw3wKJJhVEAns2V245hIitoShT+RvIg8GQbGZmWlQFd
YsHbynqHL9iwfRNv26kEqZXZOo/4D1t6Scw+OPVyba2Wyttf+qbmg+XaYMqFaxYW
mfydvdtymeCOUIPJMzw58KGPUTXJ4UPLENyayXNUHokr1a8VO8OIthY7zwi0CpvJ
IcsAY9zoGxvfbRV922mlIsw3oOBcM2IN2lC9sY469ZVnjBrdC3rsQpIBZr+Vzz8i
YlUfXLSGSyuUZUz//2eG
=VoVC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
|
||
|
Linus Torvalds
|
6c3f98fadd |
Merge branch 'i2c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang: - the I2C core gained helpers to assist drivers in handling their suspended state, and drivers were converted to use it - two new fault-injectors for stress-testing - bigger refactoring and feature improvements for the ocores, sh_mobile, and tegra drivers - platform_data removal for the at24 EEPROM driver - ... and various improvements and bugfixes all over the subsystem * 'i2c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (69 commits) i2c: Allow recovery of the initial IRQ by an I2C client device. i2c: ocores: turn incomplete kdoc into a comment i2c: designware: Do not allow i2c_dw_xfer() calls while suspended i2c: tegra: Only display error messages if DMA setup fails i2c: gpio: fault-injector: add 'inject_panic' injector i2c: gpio: fault-injector: add 'lose_arbitration' injector i2c: tegra: remove multi-master support i2c: tegra: remove master fifo support on tegra186 i2c: tegra: change phrasing, "fallbacking" to "falling back" i2c: expand minor range when registering chrdev region i2c: aspeed: Add multi-master use case support i2c: core-smbus: don't trace smbus_reply data on errors i2c: ocores: Add support for bus clock via platform data i2c: ocores: Add support for IO mapper registers. i2c: ocores: checkpatch fixes i2c: ocores: add SPDX tag i2c: ocores: add polling interface i2c: ocores: do not handle IRQ if IF is not set i2c: ocores: stop transfer on timeout i2c: tegra: add i2c interface timing support ... |
||
|
Linus Torvalds
|
ef8006846a |
Power management updates for 5.1-rc1
- Update the PM-runtime framework to use ktime instead of
jiffies for accounting (Thara Gopinath, Vincent Guittot).
- Optimize the autosuspend code in the PM-runtime framework
somewhat (Ladislav Michl).
- Add a PM core flag to mark devices that don't need any form of
power management (Sudeep Holla).
- Introduce driver API documentation for cpuidle and add a new
cpuidle governor for tickless systems (Rafael Wysocki).
- Add Jacobsville support to the intel_idle driver (Zhang Rui).
- Clean up a cpuidle core header file and the cpuidle-dt and ACPI
processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam).
- Add new cpufreq driver for Armada 8K (Gregory Clement).
- Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar,
Amit Kucheria).
- Add support for light-weight tear-down and bring-up of CPUs to the
cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar).
- Fix cpu_cooling Kconfig dependencies, add support for CPU cooling
auto-registration to the cpufreq core and use it in multiple
cpufreq drivers (Amit Kucheria).
- Fix some minor issues and do some cleanups in the davinci,
e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers
(Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel,
Taniya Das, Viresh Kumar).
- Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng
Wang).
- Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu,
Rafael Wysocki).
- Clean up multiple cpufreq drivers (Yangtao Li).
- Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas
Bulwahn).
- Add support for exposing the Energy Model via debugfs and make
multiple cpufreq drivers register an Energy Model to support
energy-aware scheduling (Quentin Perret, Dietmar Eggemann,
Matthias Kaehlcke).
- Add Ice Lake mobile and Jacobsville support to the Intel RAPL
power-capping driver (Gayatri Kammela, Zhang Rui).
- Add a power estimation helper to the operating performance points
(OPP) framework and clean up a core function in it (Quentin Perret,
Viresh Kumar).
- Make minor improvements in the generic power domains (genpd), OPP
and system suspend frameworks and in the PM core (Aditya Pakki,
Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TSKG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are PM-runtime framework changes to use ktime instead of jiffies
for accounting, new PM core flag to mark devices that don't need any
form of power management, cpuidle updates including driver API
documentation and a new governor, cpufreq updates including a new
driver for Armada 8K, thermal cleanups and more, some energy-aware
scheduling (EAS) enabling changes, new chips support in the intel_idle
and RAPL drivers and assorted cleanups in some other places.
Specifics:
- Update the PM-runtime framework to use ktime instead of jiffies for
accounting (Thara Gopinath, Vincent Guittot)
- Optimize the autosuspend code in the PM-runtime framework somewhat
(Ladislav Michl)
- Add a PM core flag to mark devices that don't need any form of
power management (Sudeep Holla)
- Introduce driver API documentation for cpuidle and add a new
cpuidle governor for tickless systems (Rafael Wysocki)
- Add Jacobsville support to the intel_idle driver (Zhang Rui)
- Clean up a cpuidle core header file and the cpuidle-dt and ACPI
processor-idle drivers (Yangtao Li, Joseph Lo, Yazen Ghannam)
- Add new cpufreq driver for Armada 8K (Gregory Clement)
- Fix and clean up cpufreq core (Rafael Wysocki, Viresh Kumar, Amit
Kucheria)
- Add support for light-weight tear-down and bring-up of CPUs to the
cpufreq core and use it in the cpufreq-dt driver (Viresh Kumar)
- Fix cpu_cooling Kconfig dependencies, add support for CPU cooling
auto-registration to the cpufreq core and use it in multiple
cpufreq drivers (Amit Kucheria)
- Fix some minor issues and do some cleanups in the davinci,
e_powersaver, ap806, s5pv210, qcom and kryo cpufreq drivers
(Bartosz Golaszewski, Gustavo Silva, Julia Lawall, Paweł Chmiel,
Taniya Das, Viresh Kumar)
- Add a Hisilicon CPPC quirk to the cppc_cpufreq driver (Xiongfeng
Wang)
- Clean up the intel_pstate and acpi-cpufreq drivers (Erwan Velu,
Rafael Wysocki)
- Clean up multiple cpufreq drivers (Yangtao Li)
- Update cpufreq-related MAINTAINERS entries (Baruch Siach, Lukas
Bulwahn)
- Add support for exposing the Energy Model via debugfs and make
multiple cpufreq drivers register an Energy Model to support
energy-aware scheduling (Quentin Perret, Dietmar Eggemann, Matthias
Kaehlcke)
- Add Ice Lake mobile and Jacobsville support to the Intel RAPL
power-capping driver (Gayatri Kammela, Zhang Rui)
- Add a power estimation helper to the operating performance points
(OPP) framework and clean up a core function in it (Quentin Perret,
Viresh Kumar)
- Make minor improvements in the generic power domains (genpd), OPP
and system suspend frameworks and in the PM core (Aditya Pakki,
Douglas Anderson, Greg Kroah-Hartman, Rafael Wysocki, Yangtao Li)"
* tag 'pm-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (80 commits)
cpufreq: kryo: Release OPP tables on module removal
cpufreq: ap806: add missing of_node_put after of_device_is_available
cpufreq: acpi-cpufreq: Report if CPU doesn't support boost technologies
cpufreq: Pass updated policy to driver ->setpolicy() callback
cpufreq: Fix two debug messages in cpufreq_set_policy()
cpufreq: Reorder and simplify cpufreq_update_policy()
cpufreq: Add kerneldoc comments for two core functions
PM / core: Add support to skip power management in device/driver model
cpufreq: intel_pstate: Rework iowait boosting to be less aggressive
cpufreq: intel_pstate: Eliminate intel_pstate_get_base_pstate()
cpufreq: intel_pstate: Avoid redundant initialization of local vars
powercap/intel_rapl: add Ice Lake mobile
ACPI / processor: Set P_LVL{2,3} idle state descriptions
cpufreq / cppc: Work around for Hisilicon CPPC cpufreq
ACPI / CPPC: Add a helper to get desired performance
cpufreq: davinci: move configuration to include/linux/platform_data
cpufreq: speedstep: convert BUG() to BUG_ON()
cpufreq: powernv: fix missing check of return value in init_powernv_pstates()
cpufreq: longhaul: remove unneeded semicolon
cpufreq: pcc-cpufreq: remove unneeded semicolon
..
|
||
|
Linus Torvalds
|
aebbfafc74 |
ARM: SoC platform updates for 5.1
The APM X-Gene platform is now maintained by folks from Ampere computing that took over the product line a while ago, this gets reflected in the MAINTAINERS file. Cleanups continue on the older mach-davinci and mach-pxa platform, to get them to be more like the modern ones. For pxa, we now remove the Raumfeld platform code as it now works with device tree based booting. i.MX adds a couple new features for the i.MX7ULP SoC Mediatek gains support for a new SoC: MT7629 is a new wireless router platform, following MT7623. Aside from those, there are the usual minor cleanups and bugfixes across several platforms. Signed-off-by: Arnd Bergmann <arnd@arndb.de> -----BEGIN PGP SIGNATURE----- Version: GnuPG v2 iQIcBAABCAAGBQJcf+c8AAoJEGCrR//JCVInuUsQAK+F+7hrfkwCSLXzqVIPMYC1 hFV11s7bgbHfzkSa6ZyFC0uuT737dZjJrOdvZOXFJ2VxDscxI62mj56jCrF8tr1x BQqIiDLGU55mLTkPiVtmVi8p79IXz2G/1dBeYrfyj/xec6DsjVkO1Cm2itQ3vg5Q ZM8DRmIxsKsUv6YSGRfwVNXso9jOh+LPxlfrGL5ijdHgzDxRr7gO+B+jxgx9Sf6s DNLj6M8L8DFo528eHp2pJNBL21pMywAaIrDELUJyg5P3XnDX18F8CjbSRgm7OG1+ hkdmML9qQlpOjokPJ9eeitX2e+tvKoXLn+N9kq12Pn4fkvJpKlOVnZmU+Le/3By+ agX7hE2A21nsZuoHQjq16QoO4X9mDee7tcDMzGwTrSq1M18m2dEJW57vivda0qKN wNJC3qwLmh2/wfxNpO2wS29hQni7cIrFgRvUPsB/u8KvzITbQ/PMGApNV+Kf7BiO mZjH8X+0IkX0veS11KLsFUCbq4ezpPCNxbul2mMIVcTIV0Oz6mQXNHAecNxCCqMk GAgi48+9KYNszG01Xqx++x79BFnIoUJp3+gIGIa8rTvdSSsF8DlQlSzXufD9Sb2h CS+M8kvgfymUrjaKZNyR5ouI1ae1Q16pbapkpS4B6ucoc4Qbqz2POiSVhex+eU/N IrEAFEhRg7iQ9NHUaWlx =vxwd -----END PGP SIGNATURE----- Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC platform updates from Arnd Bergmann: "The APM X-Gene platform is now maintained by folks from Ampere computing that took over the product line a while ago, this gets reflected in the MAINTAINERS file. Cleanups continue on the older mach-davinci and mach-pxa platform, to get them to be more like the modern ones. For pxa, we now remove the Raumfeld platform code as it now works with device tree based booting. i.MX adds a couple new features for the i.MX7ULP SoC Mediatek gains support for a new SoC: MT7629 is a new wireless router platform, following MT7623. Aside from those, there are the usual minor cleanups and bugfixes across several platforms" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (49 commits) MAINTAINERS: Update Ampere email address usb: ohci-da8xx: remove unused callbacks from platform data ARM: davinci: da830-evm: remove legacy usb helpers ARM: davinci: omapl138-hawk: remove legacy usb helpers usb: ohci-da8xx: add vbus and overcurrent gpios ARM: davinci: da830-evm: use gpio lookup entries for usb gpios ARM: davinci: omapl138-hawk: use gpio lookup entries for usb gpios usb: ohci-da8xx: add a helper pointer to &pdev->dev usb: ohci-da8xx: add a new line after local variables arm64: meson: enable g12a clock controller MAINTAINERS: Add entry for uDPU board ARM: davinci: da850-evm: use GPIO hogs instead of the legacy API arm: mediatek: add MT7629 smp bring up code Revert "ARM: mediatek: add MT7623a smp bringup code" dt-bindings: soc: fix typo of MT8173 power dt-bindings ARM: meson: remove COMMON_CLK_AMLOGIC selection arm64: meson: remove COMMON_CLK_AMLOGIC selection ARM: lpc32xx: remove platform data of ARM PL111 LCD controller ARM: lpc32xx: remove platform data of ARM PL180 SD/MMC controller ARM: lpc32xx: Use kmemdup to replace duplicating its implementation ... |
||
|
Linus Torvalds
|
6456300356 |
Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
"Here we go, another merge window full of networking and #ebpf changes:
1) Snoop DHCPACKS in batman-adv to learn MAC/IP pairs in the DHCP
range without dealing with floods of ARP traffic, from Linus
Lüssing.
2) Throttle buffered multicast packet transmission in mt76, from
Felix Fietkau.
3) Support adaptive interrupt moderation in ice, from Brett Creeley.
4) A lot of struct_size conversions, from Gustavo A. R. Silva.
5) Add peek/push/pop commands to bpftool, as well as bash completion,
from Stanislav Fomichev.
6) Optimize sk_msg_clone(), from Vakul Garg.
7) Add SO_BINDTOIFINDEX, from David Herrmann.
8) Be more conservative with local resends due to local congestion,
from Yuchung Cheng.
9) Allow vetoing of unsupported VXLAN FDBs, from Petr Machata.
10) Add health buffer support to devlink, from Eran Ben Elisha.
11) Add TXQ scheduling API to mac80211, from Toke Høiland-Jørgensen.
12) Add statistics to basic packet scheduler filter, from Cong Wang.
13) Add GRE tunnel support for mlxsw Spectrum-2, from Nir Dotan.
14) Lots of new IP tunneling forwarding tests, also from Nir Dotan.
15) Add 3ad stats to bonding, from Nikolay Aleksandrov.
16) Lots of probing improvements for bpftool, from Quentin Monnet.
17) Various nfp drive #ebpf JIT improvements from Jakub Kicinski.
18) Allow #ebpf programs to access gso_segs from skb shared info, from
Eric Dumazet.
19) Add sock_diag support for AF_XDP sockets, from Björn Töpel.
20) Support 22260 iwlwifi devices, from Luca Coelho.
21) Use rbtree for ipv6 defragmentation, from Peter Oskolkov.
22) Add JMP32 instruction class support to #ebpf, from Jiong Wang.
23) Add spinlock support to #ebpf, from Alexei Starovoitov.
24) Support 256-bit keys and TLS 1.3 in ktls, from Dave Watson.
25) Add device infomation API to devlink, from Jakub Kicinski.
26) Add new timestamping socket options which are y2038 safe, from
Deepa Dinamani.
27) Add RX checksum offloading for various sh_eth chips, from Sergei
Shtylyov.
28) Flow offload infrastructure, from Pablo Neira Ayuso.
29) Numerous cleanups, improvements, and bug fixes to the PHY layer
and many drivers from Heiner Kallweit.
30) Lots of changes to try and make packet scheduler classifiers run
lockless as much as possible, from Vlad Buslov.
31) Support BCM957504 chip in bnxt_en driver, from Erik Burrows.
32) Add concurrency tests to tc-tests infrastructure, from Vlad
Buslov.
33) Add hwmon support to aquantia, from Heiner Kallweit.
34) Allow 64-bit values for SO_MAX_PACING_RATE, from Eric Dumazet.
And I would be remiss if I didn't thank the various major networking
subsystem maintainers for integrating much of this work before I even
saw it. Alexei Starovoitov, Daniel Borkmann, Pablo Neira Ayuso,
Johannes Berg, Kalle Valo, and many others. Thank you!"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2207 commits)
net/sched: avoid unused-label warning
net: ignore sysctl_devconf_inherit_init_net without SYSCTL
phy: mdio-mux: fix Kconfig dependencies
net: phy: use phy_modify_mmd_changed in genphy_c45_an_config_aneg
net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework
selftest/net: Remove duplicate header
sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79
net/mlx5e: Update tx reporter status in case channels were successfully opened
devlink: Add support for direct reporter health state update
devlink: Update reporter state to error even if recover aborted
sctp: call iov_iter_revert() after sending ABORT
team: Free BPF filter when unregistering netdev
ip6mr: Do not call __IP6_INC_STATS() from preemptible context
isdn: mISDN: Fix potential NULL pointer dereference of kzalloc
net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external PHYs
cxgb4/chtls: Prefix adapter flags with CXGB4
net-sysfs: Switch to bitmap_zalloc()
mellanox: Switch to bitmap_zalloc()
bpf: add test cases for non-pointer sanitiation logic
mlxsw: i2c: Extend initialization by querying resources data
...
|
||
|
Michael Shych
|
9f03161a1b |
platform_data/mlxreg: additions for Mellanox watchdog driver.
There are two new fields added to mlxreg core structure: features - supported features of device and identity - device identity name. Add new defines for watchdog features. Signed-off-by: Michael Shych <michaelsh@mellanox.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> |
||
|
Mauro Carvalho Chehab
|
e907bf3c98 |
media: include: fix several typos
Use codespell to fix lots of typos over frontends. Manually verified to avoid false-positives. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Reviewed-by: Lad, Prabhakar <prabhakar.csengg@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> |
||
|
Angus Ainslie (Purism)
|
de7b7dca87 |
dmaengine: imx-sdma: add a test for imx8mq multi sdma devices
On i.mx8mq, there are two sdma instances, and the common dma framework will get a channel dynamically from any available sdma instance whether it's the first sdma device or the second sdma device. Some IPs like SAI only work with sdma2 not sdma1. To make sure the sdma channel is from the correct sdma device, use the node pointer to match. Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Daniel Baluta <daniel.baluta@nxp.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> |
||
|
Enrico Weigelt, metux IT consult
|
e09d168f13 |
gpio: AMD G-Series PCH gpio driver
GPIO platform driver for the AMD G-series PCH (eg. on GX-412TC) This driver doesn't registers itself automatically, as it needs to be provided with platform specific configuration, provided by some board driver setup code. Didn't implement oftree probing yet, as it's rarely found on x86. Cc: linux-gpio@vger.kernel.org Cc: linus.walleij@linaro.org Cc: bgolaszewski@baylibre.com Cc: dvhart@infradead.org Cc: platform-driver-x86@vger.kernel.org Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> |
||
|
Andy Shevchenko
|
a9443a6328 |
clk: x86: Move clk-lpss.h to platform_data/x86
clk-lpss.h is solely x86 related header. Move it to correct folder. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> |
||
|
Nick Crews
|
0d2f2a3da1 |
platform/chrome: wilco_ec: Add RTC driver
This Embedded Controller has an internal RTC that is exposed as a standard RTC class driver with read/write functionality. The driver is added to the drivers/rtc/ so that the maintainer of that directory will be able to comment on this change, as that maintainer is the expert on this system. In addition, the driver code is called indirectly after a corresponding device is registered from core.c, as opposed to core.c registering the driver callbacks directly. To test: > hwclock --show --rtc /dev/rtc1 2007-12-31 16:01:20.460959-08:00 > hwclock --systohc --rtc /dev/rtc1 > hwclock --show --rtc /dev/rtc1 2018-11-29 17:08:00.780793-08:00 > hwclock --show --rtc /dev/rtc1 2007-12-31 16:01:20.460959-08:00 > hwclock --systohc --rtc /dev/rtc1 > hwclock --show --rtc /dev/rtc1 2018-11-29 17:08:00.780793-08:00 Signed-off-by: Duncan Laurie <dlaurie@google.com> Signed-off-by: Nick Crews <ncrews@chromium.org> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> [Fix the sparse warning: symbol 'wilco_ec_rtc_read/write' was not declared] Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> |
||
|
Nick Crews
|
b787bb126c |
platform/chrome: wilco_ec: Add support for raw commands in debugfs
Add a debugfs attribute that allows sending raw commands to the EC. This is useful for development and debug but should not be enabled in a production environment. To test: Get the EC firmware build date First send the request command > echo 00 f0 38 00 03 00 > raw Then read the result. "12/21/18" is in the middle of the response > cat raw 00 31 32 2f 32 31 2f 31 38 00 00 0f 01 00 01 00 .12/21/18....... Get the EC firmware build date First send the request command > echo 00 f0 38 00 03 00 > raw Then read the result. "12/21/18" is in the middle of the response > cat raw 00 31 32 2f 32 31 2f 31 38 00 00 0f 01 00 01 00 .12/21/18....... Signed-off-by: Duncan Laurie <dlaurie@google.com> Signed-off-by: Nick Crews <ncrews@chromium.org> [Fix off-by-one error in wilco_ec/debugfs.c] Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> |
||
|
Nick Crews
|
7b3d4f44ab |
platform/chrome: Add new driver for Wilco EC
This EC is an incompatible variant of the typical Chrome OS embedded controller. It uses the same low-level communication and a similar protocol with some significant differences. The EC firmware does not support the same mailbox commands so it is not registered as a cros_ec device type. This commit exports the wilco_ec_mailbox() function so that other modules can use it to communicate with the EC. Signed-off-by: Duncan Laurie <dlaurie@google.com> Signed-off-by: Nick Crews <ncrews@chromium.org> [Fix the sparse warning: symbol 'wilco_ec_transfer' was not declared] Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> [Fix Kconfig dependencies for wilco_ec] Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> |
||
|
Bartosz Golaszewski
|
40b46b3b2f |
cpufreq: davinci: move configuration to include/linux/platform_data
The header containing the configuration structure for davinci cpufreq driver lives in mach-davinci/include/mach/. This is fine for now but if we want to make davinci part of the multi_v5 build, no code external to mach-davinci should include machine-specific headers. Move the configuration structure to include/linux/platform_data. While we're at it: convert the GPL-2.0 boilerplate to a proper SPDX license identifier. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Acked-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> |
||
|
Wolfram Sang
|
bceb26bffe |
at24 updates for v5.1
- finally remove legacy platform data as all users have been switched to using device properties and nvmem notifier chain - add support for the 'num-addresses' property -----BEGIN PGP SIGNATURE----- iQIzBAABCAAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAlxlKUgACgkQEacuoBRx 13KYNhAAlAIEWvp41luNy5MeAhMdLue4ruWNqkUrI/VmoxAY6DFPtwiZirjRF9HT 1XK+T+CRiHGgjiMV2YvjEh1XLZYmnuUQnTVbJ50O9UDizewcwHB4Vqi0Llyz+kaI RPzO+iyt61UYGbLmsE+UemOiefWnvq3BlPMHY4X3RjhOyDie/N8D+t+zePIhqDmZ 5iEHAkkVavznyQ60x1KZMojU6bsG6zbhoLdFcSty5oDpQ1vtsTRMvnuXWwzqnama czTLbza9XPXOoBdB7P2TAcBQII36PptCLQdmcqY9knBvRHGM6L8JKMha0huNS0u4 OogHod7M9jPJbMPnsh21S4JpR5z4R1UUeM95V8a7FRTjN0EC2jDFEAsQj1bbAMTn Zj0oYUq0lljriyuPisQ5hPkUIDV+XztOYgt/acPbo3UwtIjGe9gsCKJYVfrXM8EK NfIQsAXQb/r12f49b32IVgCxEIsk6jFvsRDAsWIUlreHf8wMWOD5fir7r1CjRqac ngQC1y9At0TgQwUN+Qzmch0oeAuOmm/yfZsroeRK3NQmKsgakRO57FfvSD0TDK6Y 5QELKonwEazgt+oSzbFlUdDyVuMIQ39pYGXgs0HJl07lPK2oyg8od0JP44Vw4SoA bxUrHUG/VL238DmkPMa+UZFpEnj7v+Lb7cgcrArTg+y3M7wpke4= =Jbyk -----END PGP SIGNATURE----- Merge tag 'at24-5.1-updates-for-wolfram' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-5.1 at24 updates for v5.1 - finally remove legacy platform data as all users have been switched to using device properties and nvmem notifier chain - add support for the 'num-addresses' property |
||
|
Andrew Lunn
|
237b5f66e1 |
i2c: ocores: Add support for bus clock via platform data
Add the I2C bus clock speed to the platform data structure. If not set, default to 100KHz as before. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> |
||
|
Federico Vaga
|
2c7e4928b3 |
i2c: ocores: add SPDX tag
It adds the SPDX tag and it removes the old text about the GPLv2. Signed-off-by: Federico Vaga <federico.vaga@cern.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> |
||
|
Bartosz Golaszewski
|
4fa882c9f6 |
eeprom: at24: remove at24_platform_data
There are no more users of at24_platform_data. Remove the relevant header and modify the driver code to not use it anymore. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> |
||
|
Bartosz Golaszewski
|
23fa70e40a |
usb: ohci-da8xx: remove unused callbacks from platform data
There are no more users of the platform_data callbacks in ohci-da8xx. Remove them. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sekhar Nori <nsekhar@ti.com> |
||
|
Linus Walleij
|
2e5a662de3 |
i2c: cbus-gpio: Switch to use GPIO descriptors
This augments the CBUS GPIO I2C driver to use GPIO descriptors for clock, sel and data. We drop the platform data that was only used for carrying GPIO numbers and use machine descriptor tables instead. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> |
||
|
Vadim Pasternak
|
946e4e02b1 |
platform_data/mlxreg: Add capability field to core platform data
Add capability field to "mlxreg_core_platform_data" structure. The purpose of this register is to provide additional info to platform driver through the atribute related capability register. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org> |
||
|
Vadim Pasternak
|
9b28aa1d0e |
platform_data/mlxreg: Document fixes for core platform data
Remove "led" from the description, since the structure "mlxreg_core_platform_data" is used not only for led data. Signed-off-by: Vadim Pasternak <vadimp@mellanox.com> Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org> |
||
|
Hans Verkuil
|
dc60a4cfb7 |
media: soc_camera_platform: remove obsolete soc_camera test driver
This is a test stub driver for soc_camera. Since soc_camera is being deprecated (and in fact, nobody is using it anymore) there's no sense in keeping this test driver. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> |
||
|
Florian Fainelli
|
8cfb5faf32 |
net: dsa: Include platform_data header file
b53 and mv88e6xxx support passing platform_data, and now that we have split the platform_data portion from the main net/dsa.h header file, include only the relevant parts. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Florian Fainelli
|
ecfc937210 |
net: dsa: Split platform data to header file
Instead of having net/dsa.h contain both the internal switch tree/driver structures, split the relevant platform_data parts into include/linux/platform_data/dsa.h and make that header be included by net/dsa.h in order not to break any setup. A subsequent set of patches will update code including net/dsa.h to include only the platform_data header. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> |
||
|
Alban Bedel
|
b172fd0c89
|
spi: ath79: Enable support for compile test
To allow building this driver in compile test we need to remove all dependency on headers from arch/mips/include. To allow this we explicitly define all the registers locally instead of using ar71xx_regs.h and we move the platform data struct definition to include/linux/platform_data/spi-ath79.h. Signed-off-by: Alban Bedel <albeu@free.fr> Signed-off-by: Mark Brown <broonie@kernel.org> |
||
|
Andy Shevchenko
|
b466a37fbc |
dmaengine: dw: convert to SPDX identifiers
This patch updates license to use SPDX-License-Identifier instead of verbose license text. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> |
||
|
Andy Shevchenko
|
69da8be90d |
dmaengine: dw: Split DW and iDMA 32-bit operations
Here is a kinda big refactoring that should have been done in the first place, when Intel iDMA 32-bit support appeared. It splits operations which are different to Synopsys DesignWare and Intel iDMA 32-bit controllers. No functional change intended. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> |
||
|
Andy Shevchenko
|
0781657796 |
dmaengine: dw: Remove unused internal property
All known devices, which use DT for configuration, support memory-to-memory transfers. So enable it by default. The rest two cases, i.e. Intel Quark and PPC460ex, instantiate DMA driver and use its channels exclusively for hardware, which means there is no available channel for any other purposes anyway. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> |
||
|
Andy Shevchenko
|
d7dba6be0f |
dmaengine: dw: Remove misleading is_private property
The commit |
||
|
Linus Torvalds
|
645ff1e8e7 |
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov: "A tiny pull request this merge window unfortunately, should get more material in for the next release: - new driver for Raspberry Pi's touchscreen (firmware interface) - miscellaneous input driver fixes" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: elan_i2c - add ACPI ID for touchpad in ASUS Aspire F5-573G Input: atmel_mxt_ts - don't try to free unallocated kernel memory Input: drv2667 - fix indentation issues Input: touchscreen - fix coding style issue Input: add official Raspberry Pi's touchscreen driver Input: nomadik-ske-keypad - fix a loop timeout test Input: rotary-encoder - don't log EPROBE_DEFER to kernel log Input: olpc_apsp - remove set but not used variable 'np' Input: olpc_apsp - enable the SP clock Input: olpc_apsp - check FIFO status on open(), not probe() Input: olpc_apsp - drop CONFIG_OLPC dependency clk: mmp2: add SP clock dt-bindings: marvell,mmp2: Add clock id for the SP clock Input: ad7879 - drop platform data support |
||
|
Linus Torvalds
|
78e8696c23 |
dmaengine-4.21-rc1
dmaengine updates for v4.21-rc1 - New driver for UniPhier MIO DMA controller - Remove R-Mobile APE6 support - Sprd driver updates and support for cyclic link-list - Remove dma_slave_config direction usage from rest of drivers - Minor updates to dmatest, dw-dmac, zynqmp and bcm dma drivers -----BEGIN PGP SIGNATURE----- iQIcBAABAgAGBQJcKipaAAoJEHwUBw8lI4NH87kQAJF5tSQzvh4alAwntJ+rNZfw bgiUW29f7PxEzEGDsTBuFsw9zPhGxPnwtXzLm2iSDBGqkEcwKc+yretuX3Pgkce+ IpPkCBGcfXptSJxFz4XxBi3HCkZ+jlhy33pH+hkW/tA4SIcA+VJjfQLePiY3sVMO 1QUFDaL9NEyEfgJTmUShaPvCiz+3OHjY/3LAMlbLqQer4C9zC3iyvZIf9lvPQQnt qJaFuEiqlhw6eOAGw+2frMYDEV57QEiRgghBZyFm5RxG19XCcPkVV9id22rz5TQb +mQXhyaLvDiztWf71dFlXW2nW8mjewcjNU4h5g3RTyLA7fpLNcpMyZY2WizIADVS x6a7/HSrDjD4CN6pGDmRi8vvqkTAEDCsrfUM6K43rAsoZzU5elVJwOv4m8WB3CCF pRlUwFi6ENt8Ov8CWgCCaY0/Bzj1FgjN3BY87amBsI9wF4fkpCPNdWw34a6lg1Kf SzyPty8Z+i+6rtKps7Mh9VOZI2tryPJzyAWrcOCDWQoiR/RWzgC3y6SuwCdiyaDf 8hFV4xnB0oVJ8vsTjF1AgxVwEsqQ7TVTIsLAns6jEnTC5FAnOLd0iwh56a+rw+lR 7e1iuQYllZ1rdMi+r5gWG4OCsZehmZgCqc250om51tzA1SDVDQ3bbx8clxZeha80 AKr5MVrIVp7riYFEICvp =+pTt -----END PGP SIGNATURE----- Merge tag 'dmaengine-4.21-rc1' of git://git.infradead.org/users/vkoul/slave-dma Pull dmaengine updates from Vinod Koul: "This includes a new driver, removes R-Mobile APE6 as it is no longer used, sprd cyclic dma support, last batch of dma_slave_config direction removal and random updates to bunch of drivers. Summary: - New driver for UniPhier MIO DMA controller - Remove R-Mobile APE6 support - Sprd driver updates and support for cyclic link-list - Remove dma_slave_config direction usage from rest of drivers - Minor updates to dmatest, dw-dmac, zynqmp and bcm dma drivers" * tag 'dmaengine-4.21-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (48 commits) dmaengine: qcom_hidma: convert to DEFINE_SHOW_ATTRIBUTE dmaengine: pxa: remove DBGFS_FUNC_DECL() dmaengine: mic_x100_dma: convert to DEFINE_SHOW_ATTRIBUTE dmaengine: amba-pl08x: convert to DEFINE_SHOW_ATTRIBUTE dmaengine: Documentation: Add documentation for multi chan testing dmaengine: dmatest: Add transfer_size parameter dmaengine: dmatest: Add alignment parameter dmaengine: dmatest: Use fixed point div to calculate iops dmaengine: dmatest: Add support for multi channel testing dmaengine: rcar-dmac: Document R8A774C0 bindings dt-bindings: dmaengine: usb-dmac: Add binding for r8a774c0 dmaengine: zynqmp_dma: replace spin_lock_bh with spin_lock_irqsave dmaengine: sprd: Add me as one of the module authors dmaengine: sprd: Support DMA 2-stage transfer mode dmaengine: sprd: Support DMA link-list cyclic callback dmaengine: sprd: Set cur_desc as NULL when free or terminate one dma channel dmaengine: sprd: Fix the last link-list configuration dmaengine: sprd: Get transfer residue depending on the transfer direction dmaengine: sprd: Remove direction usage from struct dma_slave_config dmaengine: dmatest: fix a small memory leak in dmatest_func() ... |
||
|
Linus Torvalds
|
02061181d3 |
Staging/IIO driver patches for 4.21-rc1
Here is the big staging and iio driver pull request for 4.21-rc1. Lots and lots of tiny patches here, nothing major at all. Which is good, tiny cleanups is nice to see. No new huge driver removal or addition, this release cycle, although there are lots of good IIO driver changes, addtions, and movement from staging into the "real" part of the kernel, which is always great. Full details are in the shortlog, and all of these have been in linux-next for a while with no reported issues. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> -----BEGIN PGP SIGNATURE----- iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCY93w8cZ3JlZ0Brcm9h aC5jb20ACgkQMUfUDdst+ymJRwCfeV0x/+IMS0UGh9ltHnUfCfR9bcgAmgPWMPnY bauRCLkceTjzODOR4SzH =o6Fs -----END PGP SIGNATURE----- Merge tag 'staging-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging/IIO driver updates from Greg KH: "Here is the big staging and iio driver pull request for 4.21-rc1. Lots and lots of tiny patches here, nothing major at all. Which is good, tiny cleanups is nice to see. No new huge driver removal or addition, this release cycle, although there are lots of good IIO driver changes, addtions, and movement from staging into the "real" part of the kernel, which is always great. Full details are in the shortlog, and all of these have been in linux-next for a while with no reported issues" * tag 'staging-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (553 commits) staging: mt7621-mmc: Correct spelling mistakes in comments staging: wilc1000: fix missing read_write setting when reading data mt7621-mmc: char * array declaration might be better as static const mt7621-mmc: return statement in void function unnecessary mt7621-mmc: Alignment should match open parenthesis mt7621-mmc: Removed unnecessary blank lines mt7621-mmc: Fix some coding style issues staging: android: ashmem: doc: Fix spelling staging: rtl8188eu: cleanup brace coding style issues staging: rtl8188eu: add spaces around '&' in rtw_mlme_ext.c staging: rtl8188eu: change return type of is_basicrate() to bool staging: rtl8188eu: simplify null array initializations staging: rtl8188eu: change order of declarations to improve readability staging: rtl8188eu: make some arrays static in rtw_mlme_ext.c staging: rtl8188eu: constify some arrays staging: rtl8188eu: convert unsigned char arrays to u8 staging: rtl8188eu: remove redundant declaration in rtw_mlme_ext.c staging: rtl8188eu: remove unused arrays WFD_OUI and WMM_INFO_OUI staging: rtl8188eu: remove unnecessary parentheses in rtw_mlme_ext.c staging: rtl8188eu: remove unnecessary comments in rtw_mlme_ext.c ... |
||
|
Linus Torvalds
|
8754040378 |
hwmon updates for v4.21
The big change in this series is for the most part automatic: Introducing
SENSOR[_DEVICE]_ATTR_{RO,RW,WO} variants and conversion of various drivers
to use it. This is similar to DEVICE_ATTR variants.
Other than that, we have
- Some conversions of S_<PERMS> with octal values, also automated
- Added support for Hygon Dhyana CPUs to k10temp driver
- Added support for STLM75 to lm75 driver
- B57891S0103 to ntc_thermistor
- Added pm-runtime support to ina3221 driver
- Support for PowerPC On-Chip Controller (OCC)
- Various minor bug fices and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJcHbaJAAoJEMsfJm/On5mB+IEP/R79N2zXdhtH3jPYhpdJiUIF
gwXqP7mO9JliDyQBjqwutO2QE73Zdftr7UWvaryVnBySG3LTRBmDefhD5NyvaSna
20yl0cIVqbo5cNaXlyhrZRE/ZAy6hyqGNNz28ArmNg9/w3S6dAwIUIrhy06tXrW8
bOf/k3SGNIRvSeRaFJ/2Agh83e2Vg4ckCUvGW7YIUcXUlhQITO1m71hhqDLt0XY5
enjpDafg0eSid0Jhy4aMWuiVRMdl7WR+2R+15Pm4HkH3SG/WDqNrpCcybDJoJeIv
PIsFFj5ctwcnU7IDx12TOuIWJB3hhZyAe+WitYA71VAlWQ39/1FInZ2x1fgxW17Q
lKQQYQaKa/4qNA44eEFLcsV7NiasOOwWYONWRHOvffCP6PvBmnD6VBZAhbz5dRCP
8JjmS/yhUY35dPBeTHOXEEbifTMPNajZjQrr3DtyTeuQTeaOBgU/dprJBzU/I1ie
+NYv0kEvRlWb39wZeiU1Pz93YhIcTy9EunqPhaay9P95AFn/lw1s9Ova+zrJh9oJ
aYN0sXfSsPaa+EhgqpyzH62r4bn7BVtAIsYyPqcm7z6hGnY9eNQgAC/YQEpqJq0k
wOlDb+3mLUXDPpnzoI9zg73dajTT3UAqpkjd0/ILpYltcfb5oTfbc/pRsUIjYIT2
2y7VH2Vb1dFgUlrfmxjM
=tRyC
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"The big change in this series is for the most part automatic:
Introducing SENSOR[_DEVICE]_ATTR_{RO,RW,WO} variants and conversion of
various drivers to use it. This is similar to DEVICE_ATTR variants.
Other than that, we have
- Some conversions of S_<PERMS> with octal values, also automated
- Added support for Hygon Dhyana CPUs to k10temp driver
- Added support for STLM75 to lm75 driver
- B57891S0103 to ntc_thermistor
- Added pm-runtime support to ina3221 driver
- Support for PowerPC On-Chip Controller (OCC)
- Various minor bug fices and improvements"
* tag 'hwmon-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (80 commits)
hwmon: (lm80) fix a missing check of bus read in lm80 probe
hwmon: (lm80) fix a missing check of the status of SMBus read
hwmon: (asus_atk0110) Fix debugfs_simple_attr.cocci warnings
hwmon: (ftsteutates) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (fschmd) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (emc6w201) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (emc2103) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (emc1403) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (ds620) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (ds1621) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (dell-smm-hwmon) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (da9055-hwmon) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (da9052-hwmon) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (coretemp) Replace S_<PERMS> with octal values
hwmon: (asus_atk0110) Replace S_<PERMS> with octal values
hwmon: (aspeed-pwm-tacho) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (applesmc) Replace S_<PERMS> with octal values
hwmon: (amc6821) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (adt7x10) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (adt7475) Use permission specific SENSOR[_DEVICE]_ATTR variants
...
|