If the input is ADV7604_INPUT_VGA_RGB and RGB quantization range is
set to V4L2_DV_RGB_RANGE_AUTO, video with CEA timings will be
received as RGB. For ADV7604_INPUT_VGA_COMP, automatic CSC mode
will be selected.
See table 44 on page 205 in "ADV7604 Hardware Manual, Rev. F, August 2010"
for details.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The driver strength is board dependent, so set it from the platform_data.
Signed-off-by: Mikhail Khelik <mkhelik@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The adv7604 supports four digital input ports. This patch adds support
for all of them, instead of just port A.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ignore EDID's where the header is wrong.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Whenever the hotplug pin is pulled low the chip resets a whole bunch
of registers. It turns out that this can be turned off on the adv7511.
Do so, as this 'feature' introduces race conditions in setting up
registers, particular when the hotplug pin bounces a lot.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Retry setup if the device is powered off when it should be powered on. This
state can be caused by rapid hotplug toggles.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Removed dependency on rx-sense interrupt, it's a leftover from obsolete
code. Removing this simplifies the code.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ignore EDIDs where the header is wrong.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of using two I2C operations between write and read,
use just one i2c_transfer. That allows I2C mutexes to not
let any other I2C transfer between the two.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver for Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with
embedded SoC ISP. The device is exposed as two V4L2 subdevices:
- S5K5BAF-CIS - the image sensor matrix, fixed 1600x1200 format,
no controls.
- S5K5BAF-ISP - the Image Signal Processor, formats up to 1600x1200,
pre/post ISP cropping, downscaling via selection API, controls.
[m.chehab@samsung.com: Whitespace cleanups]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The omap24xx driver and the tcm825x sensor driver are the only two
remaining drivers to still use the old deprecated v4l2-int-device API.
Nobody maintains these drivers anymore. But unfortunately the v4l2-int-device
API is used by out-of-tree drivers (MXC platform). This is a very bad situation
since as long as this deprecated API stays in the kernel there is no reason for
those out-of-tree drivers to convert.
This patch moves v4l2-int-device and the two drivers that depend on it to
staging in preparation for their removal.
If someone would be interested in getting these drivers to work, then start with
this since it's not very far from the state where they used to work:
<URL:http://vihersipuli.retiisi.org.uk/cgi-bin/gitweb.cgi?p=~sailus/linux-omap/.git;a=summary>
The branch is n800-cam. Porting to up-to-date APIs can then be done. David
might have done some work in that area, so check with him first.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: David Cohen <dacohen@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
The MT9V034 sensor is very similar to the MT9V032, with a couple of
different registers and parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
To prepare support of the MT9V034, add the necessary infrastructure to
support model-specific parameters.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Identify the model based on the I2C device name and configure formats
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The sensor can scale the image down using binning by 1, 2 or 4 in both
directions. Update size enumeration and ratio and binning factor
computation accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The active pixel array size is 753x481 with 4 additional black rows at
the top. Fix the driver accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
vs6624_read() is only called in the conditionally-compiled
vs6624_g_register() function. Make the former conditionally-compiled as
well to silence build warnings.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We had set the i2c clientdata to &flash->subdev_led[LM3560_LED1]
after call lm3560_subdev_init(flash, LM3560_LED1, "lm3560-led1"),
but the container_of() in lm3560_remove() return the wrong pointer
to flash.(should be container_of(subdev, struct lm3560_flash,
subdev_led[LM3560_LED_MAX-1])
This patch fix to set i2c clientdata to flash so we can get flash
from clientdata directly.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add the missing unlock before return from function lm3560_set_ctrl()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
git grep shows that the function is only called from ths7303.c
Fix this build warning:
CC drivers/media/i2c/ths7303.o
drivers/media/i2c/ths7303.c:86:5: warning: no previous prototype for ‘ths7303_setval’ [-Wmissing-prototypes]
int ths7303_setval(struct v4l2_subdev *sd, enum ths7303_filter_mode mode)
^
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Correct reference of reading values. (rval -> reg_val)
Add the missing unlock before return from function lm3560_get_ctrl()
to avoid deadlock.
Thank you Dan Carpenter & Sakari.
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
internal_csi_format_idx and csi_format_idx are unsigned integers,
therefore they can never be nevative.
CC drivers/media/i2c/smiapp/smiapp-core.o
In file included from include/linux/err.h:4:0,
from include/linux/clk.h:15,
from drivers/media/i2c/smiapp/smiapp-core.c:29:
drivers/media/i2c/smiapp/smiapp-core.c: In function ‘smiapp_update_mbus_formats’:
include/linux/kernel.h:669:20: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
#define min(x, y) ({ \
^
include/linux/compiler.h:153:42: note: in definition of macro ‘unlikely’
# define unlikely(x) __builtin_expect(!!(x), 0)
^
drivers/media/i2c/smiapp/smiapp-core.c:402:2: note: in expansion of macro ‘BUG_ON’
BUG_ON(min(internal_csi_format_idx, csi_format_idx) < 0);
^
drivers/media/i2c/smiapp/smiapp-core.c:402:9: note: in expansion of macro ‘min’
BUG_ON(min(internal_csi_format_idx, csi_format_idx) < 0);
^
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
git grep shows that the function is only called from ths7303.c
Fix this build warning:
CC drivers/media/i2c/ths7303.o
drivers/media/i2c/ths7303.c:86:5: warning: no previous prototype for ‘ths7303_setval’ [-Wmissing-prototypes]
int ths7303_setval(struct v4l2_subdev *sd, enum ths7303_filter_mode mode)
^
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 5aa9ae5ed5 inverted the mute control
state test in s_routing which caused the audio routing to fail. This broke
ivtv support for the Hauppauge video/audio input bracket (which adds additional
video and audio inputs) all the way back in kernel 2.6.36.
This fix fixes the condition and it also removes a nonsense check on the
balance control.
Bisected-by: Rajil Saraswat <rajil.s@gmail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Reported-by: Rajil Saraswat <rajil.s@gmail.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds the driver for the LM3560, dual LED Flash The LM3560 has two 1A
constant current driver for high current white LEDs.
It is controlled via an I2C compatible interface(up to 400kHz).
Each flash brightness, torch brightness and enable/disable can be
controlled independantly, but flash timeout and operation mode are shared.
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v3.12-rc fails to build with this error:
drivers/media/i2c/ths8200.c:49:2: error: unknown field 'bt' specified in initializer
drivers/media/i2c/ths8200.c:50:3: error: field name not in record or union initializer
drivers/media/i2c/ths8200.c:50:3: error: (near initialization for 'ths8200_timings_cap.reserved')
drivers/media/i2c/ths8200.c:51:3: error: field name not in record or union initializer
drivers/media/i2c/ths8200.c:51:3: error: (near initialization for 'ths8200_timings_cap.reserved')
...
with gcc 4.5.4. This error was not detected in builds prior to v3.12-rc.
This patch fixes this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: stable@vger.kernel.org # For kernel v3.12
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These aren't necessary after switch and while statements.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Correct spelling typo within various part of the kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix to return -ENOMEM in the new i2c client and create workqueue error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The 'driver' field of the i2c_client struct is redundant and is going to be
removed. The results of the expressions 'client->driver.driver->field' and
'client->dev.driver->field' are identical, so replace all occurrences of the
former with the later.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix to return -ENOMEM in the new i2c client and create workqueue error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
media_build/v4l/ml86v7667.c: In function 'ml86v7667_s_ctrl':
media_build/v4l/ml86v7667.c:120:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
int ret;
^
And indeed, ret is set but not used. Let's actually return the error
code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is an Analog Devices HDMI transmitter.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is a Analog Devices Component/Graphics/SD Digitizer with 2:1
Multiplexed HDMI Receiver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The ">" should be ">=" otherwise we read one space beyond the end of the
array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The check is off by one so we could read one space past the end of the
array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
is_private was set right after creating each control, but the control pointer
might be NULL in case of an error. Set it after all controls were successfully
created, since that guarantees that all control pointers are non-NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
is_private was set right after creating each control, but the control pointer
might be NULL in case of an error. Set it after all controls were successfully
created, since that guarantees that all control pointers are non-NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In most cases the v4l2_bt_timings_cap struct has all the information
necessary to determine valid timings, but occasionally there are exceptions.
Add a callback function to be able to test for those exceptions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All other functions follow the v4l2_<foo>_dv_timings pattern, do the same for
this function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CEA-861 standard allows for the 640x480 format at 25.175 MHz.
Ensure that that's allowed according to the struct v4l2_bt_timings_cap.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It's the only function in v4l2-dv-timings.c with the v4l prefix instead
of v4l2. Make it consistent with the other functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These three drivers all have code to log the dv_timings contents. Replace
that code with the new helper function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- register 0x17: CSC scaling factor was set to +/- 2.0. This register
is set by ad9389b_csc_conversion_mode() to the right value.
- register 0x3b: bits for pixel repetition and CSC was set to zero,
but that is the default value.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
state->have_monitor is set to false if the EDID that is read from
the monitor has too many segments or wrong CRC.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't log if there is no signal.
If there is a signal, then also log HDCP and audio status.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The frequency calculation has to take deep-color mode into account.
While we're at it, also log the deep-color mode in log_status.
Signed-off-by: Martin Bugge <marbugge@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The bridge driver is only notified when the input status has changed
since the previous interrupt.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
add OF support for the tvp7002 driver.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As the clock framework makes it possible to assign a device specific name to
the clocks, remove the ability to use a named clock in the driver.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The PLL calculation heuristics is rather complicated and and is often
difficult to understand to its original author.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
clamp_t does the job to put a variable into the given range.
clamp_t -> clamp as agreed with Andy.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Configure the device external clock using the common clock framework
instead of a board code callback function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Resolution set on ISP pad of S5C73M3-OIF subdev should be
propagated to source pad for TRY and ACTIVE formats.
The patch adds missing propagation for TRY format.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the mt9m111 driver to asynchronous subdevice probing. Synchronous
probing is also still possible.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The mt9t031 driver hasn't yet been updated to support asynchronous
subdevice probing. If such a probing is attempted, the driver is allowed
to fail, but it shouldn't Oops. This patch fixes such a potential NULL
pointer dereference.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
changeset 2ccf12a did a crappy job when added multi-line comment lines,
violating CodingStyle.
Change the comments added there to fulfill CodingStyle, and document
the platform_data using Documentation/kernel-doc-nano-HOWTO.txt.
Cc: Jon Arne Jørgensen <jonarne@jonarne.no>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch implements i2c_board_info.platform_data, and some options to
override the default initialization table for the GM7113C and SAA7113
chips.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of the registers changed in saa7115_init_misc table are out of range
for the gm7113c chip.
The only register that's within range, don't need to be changed here.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa711x_set_v4lstd would toggle several bits that should not be touched
when changing std. This patch fixes this.
Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simplify the code by using the new dv_timings helpers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use the new defines to calculate the full blanking and frame sizes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
v4l2-common.c contained a bunch of dv-timings related functions.
Move that to the new v4l2-dv-timings.c which is a more appropriate
place for them.
There aren't many drivers that do HDTV, so it is a good idea to separate
common code related to that into a module of its own.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ML86V7667 always transmits top field first for both PAL and NTSC -- that makes
application incorrectly treat interlaced fields when relying on the standard.
Hence we must set V4L2_FIELD_INTERLACED_TB format explicitly.
[Sergei: added a comment.]
Reported-by: Katsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Katsuya MATSUBARA <matsu@igel.co.jp>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
add OF support for the adv7343 driver.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch makes the platform data members as array wherever
possible, so as this makes easier while collecting the data
in DT case and read the entire array at once.
This patch also makes appropriate changes to board-da850-evm.c
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both synchronous and asynchronous tvp514x subdevice probing
is supported by this patch.
This patch also fixes the error path by calling
media_entity_cleanup() on failure in probe when
CONFIG_MEDIA_CONTROLLER is enabled.
Signed-off-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both synchronous and asynchronous tvp7002 subdevice probing
is supported by this patch.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Both synchronous and asynchronous adv7343 subdevice probing is supported by
this patch.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
add OF support for the ths8200 driver.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
