The lpuart_ports[] array is indexed using a value derived from the
"serialN" alias in DT, which may lead to an out-of-bounds access.
Fix this by adding a range check.
Fixes: c9e2e946fb ("tty: serial: add Freescale lpuart driver support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invoke the ->rs485_config callback on probe to set UARTMODEM_TXRTSPOL
appropriately based on the UART's device properties.
This implicitly sets UARTMODEM_TXRTSE if rs485 was enabled in the device
properties, so drop the identical code from lpuart_probe().
It also fixes a bug: If an unsupported rs485 property was specified
(rs485-rx-during-tx or rs485-rts-delay), the driver returns -ENOSYS
without performing any cleanup, in particular without calling
uart_remove_one_port() or clk_disable_unprepare(), thus leaking the
uart_port. But with the invocation of ->rs485_config, the unsupported
properties are now cleared in struct serial_rs485 and thus ignored.
It therefore seems sufficient to just log an error instead of bailing
out.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ef838a81dd ("serial: Add common rs485 device tree parsing
function") consolidated retrieval of rs485 OF properties in a common
helper function but did not #ifdef it to CONFIG_OF. The function is
therefore included on ACPI platforms as well even though it's not used.
On the other hand ACPI platforms with rs485 do exist (e.g. Siemens
IOT2040) and they may leverage _DSD to store rs485 properties. Likewise,
UART platform devices instantiated from an MFD should be able to specify
rs485 properties. In fact, the tty subsystem maintainer had asked for
a "generic" function during review of commit ef838a81dd:
https://marc.info/?l=linux-serial&m=150143441725194&w=4
Thus, instead of constraining the helper to OF platforms, make it
platform-agnostic by converting it to device_property_*() functions
and renaming it accordingly.
In imx.c, move the invocation of uart_get_rs485_mode() from
serial_imx_probe_dt() to serial_imx_probe() so that it also gets called
for non-OF devices.
In omap-serial.c, move its invocation further up within
serial_omap_probe_rs485() so that the RTS polarity can be overridden
with the driver-specific "rs485-rts-active-high" property once we
introduce a generic "rs485-rts-active-low" property.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all tty files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
As a side effect this adds support for parsing rs485-rts-delay and
rs485-rx-during-tx. As the driver doesn't support this though, probing
fails if these are defined.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit a6d7514b14 ("tty: serial: lpuart: add a more accurate baud
rate calculation method") the baud rate is now calculated inside the
lpuart32_serial_setbrg() function, so we no longer need to read the
UARTBAUD register inside lpuart32_set_termios().
The 'bd' variable can be simply removed.
This fixes the following build warning with W=1:
drivers/tty/serial/fsl_lpuart.c: In function 'lpuart32_set_termios':
drivers/tty/serial/fsl_lpuart.c:1652:32: warning: variable 'bd' set but not used [-Wunused-but-set-variable]
Fixes: a6d7514b14 ("tty: serial: lpuart: add a more accurate baud rate calculation method")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver register irq in .startup() and free the irq in
.shutdown(), then user will see the NULL interrupt output from
'cat /proc/interrupts' after the uart port test completed:
...
41: 515 0 0 0 GICv3 257 Level fsl-lpuart
42: 2 0 0 0 GICv3 258 Level
...
It is better to register all the irqs during probe function via devm_request_irq()
to avoid to call free_irq().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to duplicate a flag which IRQ core takes care of.
Replace custom flag by IRQ core API that retrieves its state.
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct serial_rs485 parameter is both input and output and is
supposed to hold the actually used configuration on return. So clear
unsupported settings.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This mirrors commit 2a41bc2a2b but for 32-bit register definitions.
Fix a minor typo while at it.
Signed-off-by: Marius Vlad <marius.vlad0@gmail.com>
CC: Nicolae Rosia <nicolae_rosia@mentor.com>
CC: Stefan Golinschi <stefan.golinschi@gmail.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0d6fce9044 ("tty: serial: lpuart: introduce lpuart_soc_data to
represent SoC property") introduced a buggy logic for detecting the 32-bit
type UART since the condition: "if (sport->port.iotype & UPIO_MEM32BE)"
is always true.
Performing such bitfield AND operation is not correct, because in the
case of Vybrid UART iotype is UPIO_MEM (2), so:
UPIO_MEM & UPIO_MEM32BE = 010 & 110 = 010, which is true.
Such logic tells the driver to always treat the UART operations as 32-bit,
leading to the driver misbehavior on Vybrid.
Fix the 32-bit type detection logic to avoid UART breakage on Vybrid.
While at it, introduce a lpuart_is_32() function to help readability.
Fixes: 0d6fce9044 ("tty: serial: lpuart: introduce lpuart_soc_data to represent SoC property")
Reported-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On new LPUART versions, the oversampling ratio for the receiver can be
changed from 4x (00011) to 32x (11111) which could help us get a more
accurate baud rate divider.
The idea is to use the best OSR (over-sampling rate) possible.
Note, OSR is typically hard-set to 16 in other LPUART instantiations.
Loop to find the best OSR value possible, one that generates minimum
baud diff iterate through the rest of the supported values of OSR.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
earlycon is executed quite early before the device tree probe,
so we need correctly initialize the port membase and iotype for
imx7ulp during early console setup before using.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lpuart of imx7ulp is basically the same as ls1021a. It's also
32 bit width register, but unlike ls1021a, it's little endian.
Besides that, imx7ulp lpuart has a minor different register layout
from ls1021a that it has four extra registers (verid, param, global,
pincfg) located at the beginning of register map, which are currently
not used by the driver and less to be used later.
To ease the register difference handling, we add a reg_off member
in lpuart_soc_data structure to represent if the normal
lpuart32_{read|write} requires plus a offset to hide the issue.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use standard port->iotype to distinguish endian difference. Note as we
read/write register by checking iotype dynamically, we need to initialize
the iotype correctly for earlycon as well to avoid a break.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com> (supporter:TTY LAYER)
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
ChangeLog:
v3->v4:
* Removed unneeded semicolon catched by 0day Robot.
v2->v3:
* Instead of using global var, use standard port->iotype to distinguish
endian difference.
v1->v2:
* No changes
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the original lpuart32_read/write takes no port specific
information arguments, it's hard to distinguish port difference
within the API. Although it works before, but not suitable anymore
when adding more new chips support.
So let's convert it to accept a new struct uart_port argument
to make it be able to retrieve more port specific information.
This is a preparation for the later adding new chips support
more easily. No functions changes.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is used to dynamically check the SoC specific lpuart properies.
Currently only the iotype is added, it functions the same as before.
With this, new chips with different iotype will be more easily added.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Mingkai Hu <Mingkai.Hu@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The console write code is not entirely race free (e.g. the operations
to disabling the UART interrupts are not atomic) hence locking is
required. This has been become apparent with the PREEMPT RT patchset
applied: With the fully preemptible kernel configuration the system
often ended up in a freeze already at startup.
Disable interrupts and lock using read_lock_irqsave. Try to lock in
the sysrq/oops case, but don't bother if locking fails.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem found via lockdep:
- lpuart_set_termios() calls del_timer_sync(&sport->lpuart_timer) while
holding sport->port.lock
- sport->lpuart_timer routine is lpuart_timer_func() that calls
lpuart_copy_rx_to_tty() that acquires same lock.
To fix, move Rx DMA stopping out of lock, as it already is in other places
in the same file.
While at it, also make Rx DMA start/stop code to look the same is in
other places in the same file.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2a41bc2a2b ("tty: serial: fsl_lpuart: add polled console
functions") caused a build warning about an unused variable, so fix it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Nicolae Rosia <nicolae_rosia@mentor.com>
Cc: Stefan Golinschi <stefan.golinschi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case where head == 0 on the circular buffer, there should be one
DMA buffer, not two. The second zero-length buffer would break the
lpuart driver, transfer would never complete.
Signed-off-by: Aaron Brice <aaron.brice@datasoft.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Tested-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds polling functions as used by kgdb.
Signed-off-by: Nicolae Rosia <nicolae_rosia@mentor.com>
Signed-off-by: Stefan Golinschi <stefan.golinschi@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function lpuart_start_rx_dma() is called from several
places, in some of which, such as lpuart_startup(), a lock
be held here, so we should use GFP_ATOMIC when a lock is held.
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for uart_ops structures that are only stored in the ops field of a
uart_port structure. This field is declared const, so uart_ops structures
that have this property can be declared as const also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct uart_ops i@p = { ... };
@ok@
identifier r.i;
struct uart_port e;
position p;
@@
e.ops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct uart_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct uart_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable Vybrid's build-in support for RS-485 auto RTS for controlling line
direction of RS-485 transceiver driver.
Enable RS485 feature by either using ioctrl 'TIOCSRS485' or enable it in the
device tree by setting 'linux,rs485-enabled-at-boot-time' property.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA mode is enabled one need to make sure the DMA channels are idle before
entering suspend mode especially when UART ports which are set as wakeup source
and console port with no_console_suspend is set. This patch takes care of
gracefully releasing DMA channels for the above two cases and start the DMA at
resume.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop PIO to DMA switching and use scatter/gather DMA for Tx path to improve
performance.
Some part of the code is borrowed from imx serial driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial approach of DMA implementatin for RX is inefficient due to switching
from PIO to DMA, this leads to overruns especially on instances with the smaller
FIFO. To address these issues this patch uses a cyclic DMA for receiver path.
Some part of the code is borrowed from atmel serial driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default the driver always configure the mode as 8s1 even when 8m1 mode is
selected. Fix this by adding support to control the space/mark bit.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8e4934c6d6 ("tty: serial: fsl_lpuart: clear receive flag on FIFO
flush") implemented clearing of the receive flag by reading the status register
only. It turned out that even though we flush the FIFO afterwards, a explicit
read of the data register is still required.
This leads to a FIFO underrun. To avoid this, follow the advice in the overrun
"Operation section": Unconditionally clear RXUF after using RXFLUSH.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the tx_empty callback only considers the Transmit Complete Flag (TC).
The reference manual is not quite clear if the TC flag covers the TX FIFO too.
Debug prints on real hardware have shown that from time to time the TC flag is
asserted (indicating Transmitter idle) while there are still data in the
TX FIFO. Hence, in this case the serial core will call the shutdown callback
even though there are data remaining in the TX FIFO buffers.
Avoid early shutdowns by considering the TX FIFO empty flag too. Also avoid
theoretical race conditions between DMA and the driver by checking whether the
TX DMA is in progress too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
platform_get_irq can fail, so we should handle negative value when
returned.
[v2]
platform_get_irq can actually return zero on some platforms. So do not
remove checks for irq == 0 there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for DT and command line based earlycon support for
lpuart and lpuart32 used on Freescale Vybrid and and QorIQ LS1021A
processors.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the receiver was enabled during startup, a character could
have been in the FIFO when the UART get initially used. The
driver configures the (receive) watermark level, and flushes the
FIFO. However, the receive flag (RDRF) could still be set at that
stage (as mentioned in the register description of UARTx_RWFIFO).
This leads to an interrupt which won't be handled properly in
interrupt mode: The receive interrupt function lpuart_rxint checks
the FIFO count, which is 0 at that point (due to the flush
during initialization). The problem does not manifest when using
DMA to receive characters.
Fix this situation by explicitly read the status register, which
leads to clearing of the RDRF flag. Due to the flush just after
the status flag read, a explicit data read is not to required.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Specify transmit FIFO size which might be different depending on
LPUART instance. This makes sure uart_wait_until_sent in serial
core getting called, which in turn waits and checks if the FIFO
is really empty on shutdown by using the tx_empty callback.
Without the call of this callback, the last several characters
might not yet be transmitted when closing the serial port. This
can be reproduced by simply using echo and redirect the output to
a ttyLP device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Timur Tabi <timur@tabi.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On uart buffer flush, serial core resets the circular buffer.
If a DMA transfer is in progress at that time, the callback
lpuart_dma_tx_complete will move buffer's tail unconditionally,
hence tail moves beyond head. Use the flush_buffer hook to
terminate the DMA imeaditely and avoid lpuart_dma_tx_complete
being called in this situation.
This bug often showed up while shutdown and lead to duplicate
serial console output.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For power management support, we should disable TX and
TX interrupt so that kernel can prepare for deep sleep.
Retain RX and RX interrupt for wakeup the kernel when
receive the input character.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To end a DMA transfer which did not consume a whole buffer (e.g. one
character only), a RX timer is used. When lots of data are received
the DMA transfer will complete and setup another DMA transfer, which
in turn might complete again. In this cases, it is not necessary to
abort the DMA transfers using the RX timer. This change pushes the
RX timer timeout into the future each time a DMA transfer completed.
Aborting the DMA was not very harmful, since the next received
character lead to setup of another RX DMA.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the DMA channel request to probe to avoid requesting the DMA
channel on each opening of the ttyLPx device. This also fixes a
potential issue that TX channel is not freed when only RX channel
allocation fails. The DMA channels are now handled independently,
so one could use UART with DMA only in TX direction for instance.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the UART is in DMA receive mode (RDMAS set) and one character
just arrived while another interrupt is handled (e.g. TX), the RDRF
(receiver data register full flag) is set due to the water level of
1. But since the DMA will take care of this character, there is no
need to handle it by calling lpuart_prepare_rx. Handling it leads to
adding the RX timeout timer twice:
[ 74.336698] Kernel BUG at 80053070 [verbose debug info unavailable]
[ 74.342999] Internal error: Oops - BUG: 0 [#1] ARM0:00.00 khungtaskd
[ 74.347817] Modules linked in: 0 S 0.0 0.0 0:00.00 writeback
[ 74.350926] CPU: 0 PID: 0 Comm: swapper Not tainted 3.19.0-rc3-00001-g39d78e2 #1788
[ 74.358617] Hardware name: Freescale Vybrid VF610 (Device Tree)t
[ 74.364563] task: 807a7678 ti: 8079c000 task.ti: 8079c000 kblockd
[ 74.370002] PC is at add_timer+0x24/0x28.0 0.0 0:00.09 kworker/u2:1
[ 74.373960] LR is at lpuart_int+0x15c/0x3d8
[ 74.378171] pc : [<80053070>] lr : [<802e0d88>] psr: a0010193
[ 74.378171] sp : 8079de10 ip : 8079de20 fp : 8079de1c
[ 74.389694] r10: 807d44c0 r9 : 8688c300 r8 : 00000013
[ 74.394943] r7 : 20010193 r6 : 00000000 r5 : 000000a0 r4 : 86997210
[ 74.401498] r3 : ffffa7da r2 : 80817868 r1 : 86997210 r0 : 86997344
[ 74.408052] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
[ 74.415489] Control: 10c5387d Table: 8611c059 DAC: 00000015
[ 74.421265] Process swapper (pid: 0, stack limit = 0x8079c230)
...
Solve this by only execute the receiver path (lpuart_prepare_rx) if
the DMA receive mode (RDMAS) is not set. Also, make sure the flag is
cleared on initialization, in case it has been left set.
This can be best reproduced using UART as a serial console, then
running top while dd'ing data into the terminal.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the serial port gets closed while a RX transfer is in progress,
the timer might fire after the serial port shutdown finished. This
leads in a NULL pointer dereference:
[ 7.508324] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 7.516590] pgd = 86348000
[ 7.519445] [00000000] *pgd=86179831, *pte=00000000, *ppte=00000000
[ 7.526145] Internal error: Oops: 17 [#1] ARM
[ 7.530611] Modules linked in:
[ 7.533876] CPU: 0 PID: 123 Comm: systemd Not tainted 3.19.0-rc3-00004-g5b11ea7 #1778
[ 7.541827] Hardware name: Freescale Vybrid VF610 (Device Tree)
[ 7.547862] task: 861c3400 ti: 86ac8000 task.ti: 86ac8000
[ 7.553392] PC is at lpuart_timer_func+0x24/0xf8
[ 7.558127] LR is at lpuart_timer_func+0x20/0xf8
[ 7.562857] pc : [<802df99c>] lr : [<802df998>] psr: 600b0113
[ 7.562857] sp : 86ac9b90 ip : 86ac9b90 fp : 86ac9bbc
[ 7.574467] r10: 80817180 r9 : 80817b98 r8 : 80817998
[ 7.579803] r7 : 807acee0 r6 : 86989000 r5 : 00000100 r4 : 86997210
[ 7.586444] r3 : 86ac8000 r2 : 86ac9bc0 r1 : 86997210 r0 : 00000000
[ 7.593085] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 7.600341] Control: 10c5387d Table: 86348059 DAC: 00000015
[ 7.606203] Process systemd (pid: 123, stack limit = 0x86ac8230)
Setup the timer on UART startup which allows to delete the timer
unconditionally on shutdown. This also saves the initialization
on each transfer.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
