This beats the heuristic that the connector is involved in what format
should be output for cases where this fails.
E.g. if there is a bridge that changes format between the encoder and the
connector, or if some of the RGB pins between the lcd controller and the
encoder are not routed on the PCB.
This is critical for the devices that have the "conflicting output
formats" issue (SAM9N12, SAM9X5, SAMA5D3), since the most significant
RGB bits move around depending on the selected output mode. For
devices that do not have the "conflicting output formats" issue
(SAMA5D2, SAMA5D4), this is completely irrelevant.
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180825085620.10566-5-peda@axentia.se
But only if the highest pixel-clock frequency lower than requested
is significantly less accurate than the lowest frequency higher than
requested.
I pulled "10 times" as the discriminator out of the hat, and went with
that.
This is useful, if e.g. the target pixel-clock is 65MHz and the sys_clk
is 132MHz. In this case the highest possible pixel-clock lower than the
requested 65MHz is 52.8MHz, which is almost 20% off (and outside the
spec for the panel). The lowest possible pixel-clock higher than 65MHz
is 66MHz, which is a *much* better match, and only 1.5% off.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824092458.13165-3-peda@axentia.se
If the divider used to get the pixel-clock is small, the granularity
of the frequencies possible for the pixel-clock is quite coarse. E.g.
requesting a pixel-clock of 65MHz with a sys_clk of 132MHz results
in the divider being set to 3 ending up with 44MHz.
By preferring the doubled sys_clk as base, the divider instead ends
up as 5 yielding a pixel-clock of 52.8Mhz, which is a definite
improvement.
While at it, clamp the divider so that it does not overflow in case
it gets big.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180824092458.13165-2-peda@axentia.se
It's dead code because this is now handled in the core.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Engestrom <eric@engestrom.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-5-daniel.vetter@ffwll.ch
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
for_each_obj_in_state is about to be removed, so use the new iterator
macros.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170712081344.25495-9-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The CRTC .disable() helper operation is deprecated for atomic drivers,
the new .atomic_disable() helper operation being preferred. Convert all
atomic drivers to .atomic_disable() to avoid cargo-cult use of
.disable() in new drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-3-laurent.pinchart+renesas@ideasonboard.com
The old state is useful for drivers that need to perform operations at
enable time that depend on the transition between the old and new
states.
While at it, rename the operation to .atomic_enable() to be consistent
with .atomic_disable(), as the .enable() operation is used by atomic
helpers only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-drm and mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> # for hdlcd and mali-dp
Acked-by: Stefan Agner <stefan@agner.ch> # for fsl-dcu
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-2-laurent.pinchart+renesas@ideasonboard.com
All layers of all supported chips support this, the only variable is the
base address of the lookup table in the register map.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1498107791-17450-3-git-send-email-peda@axentia.se
Now that we have a callback to check if crtc supports a given mode
we can use it in atmel-hlcdc so that we restrict the number of probbed
modes to the ones we can actually display.
Also, remove the mode_fixup() callback as this is no longer needed
because mode_valid() will be called before.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/95fd6c06c58bd0b957e36a8d7068e6a74b581304.1495720737.git.joabreu@synopsys.com
The current suspend resume implementation is assuming register values are
kept when entering suspend, which is no longer the case with the
suspend-to-RAM on the sama5d2.
While at it, switch to the generic infrastructure to enter suspend mode
(drm_atomic_helper_suspend/resume()).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1488371461-22243-1-git-send-email-boris.brezillon@free-electrons.com
An HLCDC layers in Atmel's nomenclature is either a DRM plane or a 'Post
Processing Layer' which can be used to output the results of the HLCDC
composition in a memory buffer.
atmel_hlcdc_layer.c was designed to be generic enough to be re-usable in
both cases, but we're not exposing the post-processing layer yet, and
even if we were, I'm not sure the code would provide the necessary tools
to manipulate this kind of layer.
Moreover, the code in atmel_hlcdc_{plane,layer}.c was designed before the
atomic modesetting API, and was trying solve the
check-setting/commit-if-ok/rollback-otherwise problem, which is now
entirely solved by the existing core infrastructure.
And finally, the code in atmel_hlcdc_layer.c is over-complicated compared
to what we really need. This rework is a good excuse to simplify it. Note
that this rework solves an existing resource leak (leading to a -EBUSY
error) which I failed to clearly identify.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
The vblank hooks in struct drm_driver are deprecated and only meant for
legacy drivers. For modern drivers with DRIVER_MODESET flag, the hooks
in struct drm_crtc_funcs should be used instead.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-8-git-send-email-shawnguo@kernel.org
The atmel_hlcdc_crtc_reset() function is never used outside the file and
can be static. This avoids a warning from sparse.
Signed-off-by: Thierry Reding <treding@nvidia.com>
As promised, piles of prep work all around:
- drm_atomic_state rework, prep for nonblocking commit helpers
- fence patches from Gustavo and Christian to prep for atomic fences and
some cool work in ttm/amdgpu from Christian
- drm event prep for both nonblocking commit and atomic fences
- Gustavo seems on a crusade against the non-kms-native version of the
vblank functions.
- prep work from Boris to nuke all the silly ->best_encoder
implementations we have (we really only need that for truly dynamic
cases like dvi-i vs dvi-d or dp mst selecting the right transcoder on
intel)
- prep work from Laurent to rework the format handling functions
- and few small things all over
* tag 'topic/drm-misc-2016-06-07' of git://anongit.freedesktop.org/drm-intel: (47 commits)
drm/dsi: Implement set tear scanline
drm/fb_cma_helper: Implement fb_mmap callback
drm/qxl: Remove useless drm_fb_get_bpp_depth() call
drm/ast: Remove useless drm_fb_get_bpp_depth() call
drm/atomic: Fix remaining places where !funcs->best_encoder is valid
drm/core: Change declaration for gamma_set.
Documentation: add fence-array to kernel DocBook
drm/shmobile: use drm_crtc_vblank_{get,put}()
drm/radeon: use drm_crtc_vblank_{get,put}()
drm/qxl: use drm_crtc_vblank_{get,put}()
drm/atmel: use drm_crtc_vblank_{get,put}()
drm/armada: use drm_crtc_vblank_{get,put}()
drm/amdgpu: use drm_crtc_vblank_{get,put}()
drm/virtio: use drm_crtc_send_vblank_event()
drm/udl: use drm_crtc_send_vblank_event()
drm/qxl: use drm_crtc_send_vblank_event()
drm/atmel: use drm_crtc_send_vblank_event()
drm/armada: use drm_crtc_send_vblank_event()
drm/doc: Switch to sphinx/rst fixed-width quoting
drm/doc: Drop kerneldoc for static functions in drm_irq.c
...
If kmalloc() returned NULL we would end up dereferencing "state" a
couple lines later.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reset crtc->state to NULL after freeing the state object and call
__drm_atomic_helper_crtc_destroy_state() helper instead of manually
calling drm_property_unreference_blob().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
It's unused, and really this helper should only look at the state
structure and nothing else.
v2: Rebase on top of rockchip changes
v3: Drop unrelated hunk, spotted by Laurent.
v4: Rebase onto mtk driver merge.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1462804451-15318-1-git-send-email-daniel.vetter@ffwll.ch
In relation with the actuall bandwidth consumed on a DMA Source interface,
choose the less used one for a created plane.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Move the adjusted display mode check into ->mode_fixup().
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In order to support multiple outputs we need to move the output mode
selection to the CRTC object, so that the output validity check can be
done against the drm_atomic_state.
If the connectors selected by a specific mode setting are requiring
incompatible bus format the atomic operation is aborted (->atomic_check()
returns -EINVAL).
In order to implement that, we need to define our own CRTC state and
overload default ->reset(), ->atomic_duplicate_state() and
->atomic_destroy_state() functions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The only thing this did was cancle pending flip events, and the core
takes care of that now.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Daniel Stone <daniels@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453756616-28942-5-git-send-email-daniel.vetter@ffwll.ch
Done with coccinelle for the most part. However, it thinks '...' is
part of the semantic patch, so I put an 'int DOTDOTDOT' placeholder
in its place and got rid of it with sed afterwards.
I didn't convert drm_crtc_init() since passing the varargs through
would mean either cpp macros or va_list, and I figured we don't
care about these legacy functions enough to warrant the extra pain.
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
)
{ ... }
@@
identifier dev, crtc, primary, cursor, funcs;
@@
int drm_crtc_init_with_planes(struct drm_device *dev,
struct drm_crtc *crtc,
struct drm_plane *primary, struct drm_plane *cursor,
const struct drm_crtc_funcs *funcs
+ ,const char *name, int DOTDOTDOT
);
@@
expression E1, E2, E3, E4, E5;
@@
drm_crtc_init_with_planes(E1, E2, E3, E4, E5
+ ,NULL
)
v2: Split crtc and plane changes apart
Pass NULL for no-name instead of ""
Leave drm_crtc_init() alone
v3: Add ', or NULL...' to @name kernel doc (Jani)
Annotate the function with __printf() attribute (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449670771-2751-1-git-send-email-ville.syrjala@linux.intel.com
In intel it's useful to keep track of some state changes with old
crtc state vs new state, for example to disable initial planes or
when a modeset's prevented during fastboot.
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
[danvet: squash in fixup for exynos provided by Maarten.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_vblank_on() now warns on nested use or if vblank is not properly
initialized. This patch fixes Atmel HLCDC vblank initial state.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Unfortunately we used the enabled flag in struct drm_crtc instead of the
enabled flag in struct atmel_hlcdc_crtc. This obviously leads to
discrepancies on crtc enable state.
This patch fixes the issue by using the struct atmel_hlcdc_crtc enabled
flag in PM support.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into drm-next
Linux 4.0-rc3 backmerge to fix two i915 conflicts, and get
some mainline bug fixes needed for my testing box
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/intel_display.c
Remove this configuration bit in crtc driver as the rising edge clock is widely
used.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Some LCD panels have back-powering issue when un-powered, allows users
to use an alternate pinctrl "sleep" in order to clamp outputs to a
wanted state at suspend.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The HLCDC IP provides a way to discard a specific area on the primary
plane (in case at least one of the overlay is activated and alpha
blending is disabled).
Doing this will reduce the amount of data to transfer from the main
memory to the Display Controller, and thus alleviate the load on the
memory bus (since this link is quite limited on such hardware,
this kind of optimization is really important).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Convert the HLCDC driver to atomic mode-setting.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Atmel HLCDC (HLCD Controller) IP available on some Atmel SoCs (i.e.
at91sam9n12, at91sam9x5 family or sama5d3 family) provides a display
controller device.
This display controller supports at least one primary plane and might
provide several overlays and an hardware cursor depending on the IP
version.
At the moment, this driver only implements an RGB connector to interface
with LCD panels, but support for other kind of external devices might be
added later.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Tested-by: Anthony Harivel <anthony.harivel@emtrion.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
