Add MMC_CAP2_NO_PRESCAN_POWERUP to sdhci-pci.c also, use mmc_power_off()
for MMC_CAP2_NO_PRESCAN_POWERUP.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
[cjb: previously applied v1 of this patch instead of v4]
Signed-off-by: Chris Ball <cjb@laptop.org>
Add SDHC DMA channel description to the mpc512x device tree to enable
slave channel requesting in the mxcmmc driver.
mpc512x DMA engine doesn't support endianness conversion when
reading/writing data from peripheral's FIFO, so we have to swap data
buffers before each DMA write and after each DMA read transfer manually.
Since chained SDHC DMA transfers are not supported on mpc512x, limit
'max_segs' tunable parameter to one and initialise it to 64 only when
running on i.MX platforms.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
slot-gpio API suppors read-only detection when "wp-gpios"
property is present in the device tree mmc node. Use this
API for write-protect detection.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDHC controller on mpc512x is compatible with i.MX31 SDHC,
so the mxcmmc driver can be used on mpc512x, too. Extend the
driver to support mpc512x as well.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
mxcmci_dma_callback() is invoked by DMA drivers in soft-irq
context and can be interrupted by the mxcmci_irq() interrupt
which can finish the mmc request or data transfer and set
host->req or host->data pointers to NULL. Then mxcmci_data_done()
crashes with a null pointer dereferences. Protect all accesses
to host->req and host->data by spin locks.
Also check host->data pointer in mxcmci_watchdog() before
dereferencing it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adding devicetree support for imx21-mmc and imx31-mmc. Based on generic
gpio helper functions by Guennadi and generic DMA devicetree bindings.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
With device core now able to setup the default pin configuration,
the pin configuration code based on the deprecated Samsung specific
gpio bindings is removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to bindings documentation for mmc, the property 'broken-cd'
can be used to indicate card-detection is not available and polling
must be used instead. This patch retrieves this property
and sets a custom flag. On the get_cd() hook, it returns 1 if
the flag is set, to always assume the card is present.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some boards have non removable cards like eMMC. Handle such case.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The card-detect GPIO is inverted on some boards. Handle such case.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put_noidle in such case.
Signed-off-by: Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes bug when card is present during boot.
Bug was introduced due commit "mmc: mxcmmc: fix bug that may block a
data transfer forever". When a card is present "mxcmci_setup_data"
function is executed, but the timer is not initialized.
...
i.MX SDHC driver
mmc0: SD Status: Invalid Allocation Unit size.
mmc0: new SD card at address b368
mmcblk0: mmc0:b368 SDC 1.91 GiB
------------[ cut here ]------------
kernel BUG at kernel/timer.c:729!
Internal error: Oops - BUG: 0 [#1] PREEMPT ARM
CPU: 0 Not tainted (3.9.0-rc5-next-20130404 #2)
PC is at mod_timer+0x168/0x198
LR is at mxcmci_request+0x21c/0x328
...
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit fa5501890d introduced a performance
regression by adding mmc_power_up() to mmc_start_host(). mmc_power_up()
is not necessary to host controller initialization, it is part of card
initialization and is performed anyway asynchronously.
This patch allows a driver to leave the power up in asynchronous code
(as it was before).
On my current target platform this reduces driver initialization from:
[ 1.313220] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 102008 usecs
to this:
[ 1.217209] initcall sdhci_acpi_driver_init+0x0/0x12 returned 0 after 8331 usecs
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 3500ed90b2.
The reverted patch caused a significant performance regression when
booting with the root file system on eMMC.
Before the patch:
[ 1.625623] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
After the patch:
[ 1.935851] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
That was an addition of 310 ms which is a 19% performance degradation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The driver is doing, by default, multi-block reads. When a block error
occurs, card/block.c instigates a single block read: "mmcblk0: retrying
using single block read". It leaves the sg chain intact and just changes
the length attribute for the first sg entry and the overall sg_len
parameter. When atmci_read_data_pio is called to read the single block
of data it ignores the sg_len and expects to read more than 512 bytes as
it sees there are multiple items in the sg list. No more data comes as
the controller has only been commanded to get one block.
Signed-off-by: Terry Barnaby <terry@beam.ltd.uk>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org> # 3.2+
Signed-off-by: Chris Ball <cjb@laptop.org>
PARTITION_SUPPORT needs to be set before doing the compare on version
number so the bit width test does not get invalid data. Before this
patch, a Sandisk iNAND eMMC card would detect 1-bit width although
the hardware supports 4-bit.
Only affects old emmc devices - pre 4.4 devices.
Reported-by: Elad Yi <elad.yi@gmail.com>
Signed-off-by: Philip Rakity <prakity@yahoo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
regulator_enable() is declared with __must_check attribute.
Hence check the return value to ensure that the regulator is enabled.
Fixes the following warning:
drivers/mmc/host/dw_mmc.c:2461:19: warning:
ignoring return value of ‘regulator_enable’, declared with attribute
warn_unused_result [-Wunused-result]
drivers/mmc/host/dw_mmc.c: In function ‘dw_mci_init_slot’:
drivers/mmc/host/dw_mmc.c:1994:19: warning:
ignoring return value of ‘regulator_enable’, declared with attribute
warn_unused_result [-Wunused-result]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/mmc/host/sdhci-spear.c:295:12: warning: 'sdhci_suspend' defined but not used [-Wunused-function]
drivers/mmc/host/sdhci-spear.c:308:12: warning: 'sdhci_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When card is power-on/off, need to control the power-enable register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-pxav3 host controller used SDCLK for data timeout.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
1. seperate device tree parsing from platform data handling which
can make further work easy when platform data can be removed.
2. add calling mmc_of_parse which can parse more of property and
pxav3_get_mmc_pdata can be shrinked a lot.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Flag PXA_FLAG_CARD_PERMANENT is set in sdhci_pxa_platdata flags to
indicate that the card is always wired to host, like on-chip emmc,
which is permanently present and don't need detection.
So only MMC_CAP_NONREMOVABLE should be set for this case. But current
code also sets SDHCI_QUIRK_BROKEN_CARD_DETECTION, which doesn't make
sense.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci_pltfm_init can set host->ops and host->quirks if sdhci_pltfm_data
is transfered as arguments. Then no need to set them manually in
sdhci_pxav3_probe.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mci_writew causes a failure of fifo access for 64-bit.
mci_writeq is correct.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mvsdio driver was already using some dev_*() functions to print
some messages, but still using pr_*() functions for some others. This
patch converts all messages to use dev_*() functions.
Many of the pr_*() function calls were printing the output of
mmc_hostname() to preprend the message with an identifier for the
device. Since the dev_*() functions do that automatically, this patch
also gets rid of those string prefixes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ralph Droms <rdroms@gmail.com> reported that 3.9-rc was breaking the
SDIO interface on his Sheevaplug platform, and that the recent changes
to the mvsdio driver are responsible for this breakage. Precisely, the
regression has been introduced by 07728b77c0 (mmc: mvsdio: use
slot-gpio for card detect gpio).
After investigation, is turns out that the Sheevaplug does not have
any "card detect" GPIO, and the Sheevaplug has not been converted to
the Device Tree. Therefore, the Sheevaplug board code does not define
a value for the .gpio_card_detect field of the mvsdio_platform_data
structure, which means that its value is 0. Unfortunately,
gpio_is_valid() considers 0 as a valid GPIO, and therefore calls
mmc_gpio_request_cd(), which fails and makes the entire probing of the
driver fail.
In fact, in the previous mvsdio code, before the Device Tree binding
was introduced, 0 was not considered as a valid GPIO. Therefore, this
fix revert back to this behavior in the non-DT case, by setting the
gpio_card_detect and gpio_write_protect local variables to -EINVAL
when the corresponding fields of the mvsdio_platform_data structure
are set to zero (i.e, left undefined). Of course, it prevents to use
GPIO 0 as a card detect or write protect GPIO, but it was a defiency
of the previous non-DT code, and the fix moving forward is to convert
platforms to the Device Tree.
The problem has been reproduced successfully on the Kirkwood-based
Marvell DB-88F6281-BP Development Board (that doesn't use the Device
Tree) and the fix has proven to work properly, after of course
removing the gpio_card_detect field of the mvsdio_platform_data
instance for this board.
Reported-by: Ralph Droms <rdroms@gmail.com>
Tested-by: Ralph Droms <rdroms@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the new driver for CSR SiRF SoCs:
SiRFprimaII: unicore ARM Cortex-A9
SiRFatlas6: unicore ARM Cortex-A9
SiRFmarco: dual core ARM Cortex-A9 SMP
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
For normal request mmc_blk_issue_rq is called twice with asynchronous
transfer(cur and prev). Host's claim and release can be done in each
mmc_blk_issue_rq. However, Special request is currently excluded in
asynchronous transfer. After special request is finished, if there is
no new request, mmc_release_host won't be called in mmc_blk_issue_rq.
The problem is founded during mmc_suspend.
[<c0541124>] (__schedule+0x0/0x78c) from [<c05419e8>] (schedule+0x38/0x78)
[<c05419b0>] (schedule+0x0/0x78) from [<c03a843c>] (__mmc_claim_host+0xac/0x1b4)
[<c03a8390>] (__mmc_claim_host+0x0/0x1b4) from [<c03ac98c>] (mmc_suspend+0x28/0x9c)
[<c03ac964>] (mmc_suspend+0x0/0x9c) from [<c03aad24>] (mmc_suspend_host+0xb4/0x194)
...
Reported-by: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC hosts are added asynchronously. We need to wait until detect returns to
avoid failed root filesystem mounts.
VFS: Cannot open root device "mmcblk0p1" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
mmc0: host does not support reading read-only switch. assuming write-enable.
1f00 256 mtdblock0 (driver?)
1f01 256 mtdblock1 (driver?)
1f02 2560 mtdblock2 mmc0: new SDHC card at address b368
(driver?)
1f03 29696 mtdblock3 (driver?)
1f04 16384 mtdblock4 mmcblk0: mmc0:b368 USD 3.72 GiB
(driver?)
mmcblk0: p1
b300 3910656 mmcblk0 driver: mmcblk
b301 3906560 mmcblk0p1 00000000-01
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All users of the sdhci_ops struct in the sdhci core already treat it as
const. The sdhci-pltfm code itself never actually looks at the ops field
of the sdhci_pltfm_data struct and merely passes it on to the sdhci core,
so make we can make it const in the sdhci_pltfm_data struct as well.
This allows us to declare sdhci_ops structs as const in drivers using
the sdhci-pltfm helper code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The sdhci_pltfm_data struct is never modified within the sdhci_pltfm
module. So make the pdata parameter to sdhci_pltfm_init and
sdhci_pltfm_register const. This allows drivers to declare their
sdhci_pltfm_data struct as const.
This patch also makes the sdhci_pltfm_data declarations const where
possible.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix regression introduced by commit 796211b795 ("mmc: atmel-mci: add
pdc support and runtime capabilities detection") which removed the need
for CONFIG_MMC_ATMELMCI_DMA but kept the Kconfig-entry as well as the
compile guards around dma_release_channel() in remove(). Consequently,
DMA is always enabled (if supported), but the DMA-channel is not
released on module unload unless the DMA-config option is selected.
Remove the no longer used CONFIG_MMC_ATMELMCI_DMA option completely.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the compatible string for MSHC controller of Exynos4412.
And exynos5250_dwmmc_caps is renamed to exynos_dwmmc_caps, since it has the
capabilities of common features supported by Exynos4 and Exynos5.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use resource_size() instead of explicit calculation. This was found via
make coccicheck.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit f9c2a0dc42
"mmc: dw_mmc: Fix PIO mode with support of highmem" introduced
a regression since v3.2 making the mmc_test hang on test #13
with a "Data starvation by host timeout" interrupt.
This is because, sg_mapping_iter is used to iterate through the
data which spans on multiple pages. The problem is detected on
unaligned data submission where the code previously checked for
!(sg_next(host->sg)) which is true because we only have a single
scatter/gather list which then expands to multiple pages.
Therefore, the driver incorrectly assumed that this was the last
list item and submitted unaligned data to the mmc device. This
overflowed the FIFO on the device before all the data were written
to it. The code was fixed to only submit unaligned data when we are
handling the last sg_miter item by checking whether we reached
the desired data length or not.
The patch was tested against mmc_test and all the tests passed.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Previously, it was possible to add either 0 bytes or add nbytes
twice if we broke out of the outer loop and then carry on to the
"done" label. This is now fixed by adding the transferred bytes
right after the pull/pop operation
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is no reason to loop when handling an interrupt. The "if" clauses
will handle all of them sequentially. This also eliminates the extra loop
we used to take with no pending interrupts and we ended up breaking out
of the while loop.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
host->data_offset is initialised at the end of the probe function
depending on the VERID register, and is used for PIO operations. Move
this initialisation earlier, before IRQs or slots are initialised, to be
sure that PIO won't occur prior to host->data_offset being initialised.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Call the setpower platform callback in response to set_ios with
ios->power_mode == MMC_POWER_UP or MMC_POWER_OFF, instead of from the
card detect work function.
This appears to fix a problem I have where a card stuck in a funny state
doesn't get properly cleared by the power being turned off, presumably
due to lack of power sequencing. This resulted in the following log
messages after boot:
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 300000Hz, actual 298922HZ div = 167)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 200000Hz, actual 199680HZ div = 250)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 195765Hz, actual 195764HZ div = 255)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 400000Hz, actual 399360HZ div = 125)
mmc0: error -110 whilst initialising SD card
mmc_host mmc0: Bus speed (slot 0) = 99840000Hz (slot req 300000Hz, actual 298922HZ div = 167)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes:
/git/arm-soc/drivers/mmc/host/sdhci.c: In function 'sdhci_add_host':
/git/arm-soc/drivers/mmc/host/sdhci.c:2910:19: warning: ignoring
return value of 'regulator_enable', declared with attribute
warn_unused_result [-Wunused-result]
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Used resource_size function instead of explicit computation.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The variable 'mmc' is initialized but never used, so remove it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes timeout problems on t4240's sdhci controller:
mmc0: Too large timeout requested for CMD25!
mmc0: Too large timeout requested for CMD25!
mmc0: Too large timeout requested for CMD25!
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For some Realtek card readers, the power up sequence can only be executed
when power has been turned off fully.
So the rtsx host should not start power up sequence again when set_ios
been called if the power has been turned on.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
With device core now able to setup the default pin configuration,
the call to devm_pinctrl_get_select_default can be removed. And
the pin configuration code based on the deprecated Samsung specific
gpio bindings is also removed.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
