The ports array is filled in as ports are probed, but if probing doesn't
finish, we need to stop only those ports that where probed successfully.
Check the ports array for NULL to skip un-probed ports when stopping.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove support for legacy ndo ops
.ndo_vlan_rx_add_vid/.ndo_vlan_rx_kill_vid. Rocker will use
bridge_setlink/dellink exclusively for VLAN add/del operations.
The legacy ops are needed if using 8021q driver module to setup VLANs on
the port. But an alternative exists in using bridge_setlink/delink to
setup VLANs, which doesn't depend on 8021q module. So rocker will switch
to the newer setlink/dellink ops. VLANs can added/delete from the port,
regardless if port is bridged or not, using the bridge commands:
bridge vlan [add|del] vid VID dev DEV self
(Yes, I agree it's confusing to use the "bridge" command to set a VLAN on a
non-bridged port).
Using setlink/dellink over legacy ops let's us handle the stacked driver
case automatically. It's built-in. setlink also pass additional flags
(PVID, egress untagged) that aren't available with the legacy ops.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the port joins a bridge, the port's internal VLAN ID needs to change
to the bridge's internal VLAN ID. Likewise, when leaving the bridge, the
internal VLAN ID reverts back the port's original internal VLAN ID. (The
internal VLAN ID is used by device to internally mark untagged pkts with
some VLAN, which will eventually be removed on egress...think PVID). When
the internal VLAN ID changes, we need to update the VLAN table entries and
the router MAC entries for IP/IPv6 to reflect the new internal VLAN ID.
This patch makes use of the common rocker_port_vlan_add/del functions to
make sure the tables are updated for the current internal VLAN ID.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On port probe, install by default untagged VLAN support. This is
equivalent to running the command:
bridge vlan add vid 0 dev DEV self
A user could, if they wanted, manaully removing untagged support from the
port by running the command:
bridge vlan del vid 0 dev DEV self
But installing it by default on port initialization gives the normal
expected behavior.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic house keeping: If there is an error adding the router MAC for this
vlan, removing the just installed VLAN table entry to leave device in same
state as before failure.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating the array of rocker port pointers, zero the array values so
we can test for !NULL to see if port is allocated/registered. We'll need
this later when installing untagged VLAN support for each port, during port
probe. It's a long story, but to install a VLAN (vid=0 for untagged, in
this case) on a port, we'll need to scan other ports to see if the VLAN
group for that VLAN has been setup. To scan the other ports, we need to
walk the port array.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rocker (switch) of a rocker_port may be trivially obtained from
the latter it seems cleaner not to pass the former to a function when
the latter is being passed anyway.
rocker_port_rx_proc() is omitted from this change as it is a hot path case.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark parameters and local variables as const where possible.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused rocker_port parameter from rocker_port_kfree.
Also remove the rocker_port parameter from callers of rocker_port_kfree
where the parameter it is now unused.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The motivation for this is that rocker_port_internal_vlan_id_{get,put} appear
to only partially implement the transaction model: memory allocation
and freeing is transactional, but hash and bitmap manipulation is not.
The latter could be fixed, however, as it is not currently exercised
due to trans always being SWITCHDEV_TRANS_NONE it seems cleaner
to make rocker_port_internal_vlan_id_get non-transactional.
This problem was introduced by c4f20321d9 ("rocker: support
prepare-commit transaction model").
Found by inspection.
I do not believe that this change should have any run-time effect.
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rocker_port_ipv4_nh() and in turn rocker_port_ipv4_neigh() may be
be called with trans == SWITCHDEV_TRANS_PREPARE and then
trans == SWITCHDEV_TRANS_COMMIT from switchdev_port_obj_set() via
fib_table_insert().
The first time that rocker_port_ipv4_nh() is called, with
trans == SWITCHDEV_TRANS_PREPARE, _rocker_neigh_add() adds a new entry to
the neigh table.
And the second time rocker_port_ipv4_nh() is called, with
trans == SWITCHDEV_TRANS_COMMIT, that entry is found. This causes
rocker_port_ipv4_nh() to believe it is not adding an entry and thus it
frees "entry", which is still present in rocker driver's neigh table.
This problem does not appear to affect deletion as my analysis is that
deletion is always performed with trans == SWITCHDEV_TRANS_NONE.
For completeness _rocker_neigh_{add,del,prepare} are updated not to
manipulate fib table entries if trans == SWITCHDEV_TRANS_PREPARE.
Fixes: c4f20321d9 ("rocker: support prepare-commit transaction model")
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- introduce port fdb obj and generic switchdev_port_fdb_add/del/dump()
- use switchdev_port_fdb_add/del/dump in rocker/team/bonding ndo ops.
- add support for fdb obj in switchdev_port_obj_add/del/dump()
- switch rocker to implement fdb ops via switchdev_ops
v3: updated to sync with named union changes.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we get a neighbour through looking up arp cache or creating a
new one in rocker_port_ipv4_resolve(), the neighbour's refcount is
already taken. But as we don't put the refcount again after it's
used, this makes the neighbour entry leaked.
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older gcc versions (e.g. gcc version 4.4.6) don't like anonymous unions
which was causing build issues on the newly added switchdev attr/obj
structs. Fix this by using named union on structs.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And let driver convert it to host-byte order as needed.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Well almost clean: ignore the CHECKs for space after cast operator and some
longer-than-80 char cases where for readability it's better to keep as-is.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa said remove the feature flag for this series and she'll work on
bringing it back if needed at a later date.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv4 FIB ops convert nicely to the switchdev objs and we're left with
only four switchdev ops: port get/set and port add/del. Other objs will
follow, such as FDB. So go ahead and convert IPv4 FIB over to switchdev
obj for consistency, anticipating more objs to come.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rocker, bonding and team and switch over to the new
switchdev_port_bridge_dellink to avoid duplicating code in each driver.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rocker, bonding, and team can now use the switchdev bridge setlink to parse
raw netlink; no need to duplicate this code in each driver.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
rocker: use switchdev get/set attr for bridge port flags
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
STP update is just a settable port attribute, so convert
switchdev_port_stp_update to an attr set.
For DSA, the prepare phase is skipped and STP updates are only done in the
commit phase. This is because currently the DSA drivers don't need to
allocate any memory for STP updates and the STP update will not fail to HW
(unless something horrible goes wrong on the MDIO bus, in which case the
prepare phase wouldn't have been able to predict anyway).
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
For rocker, support prepare-commit transaction model for setting attributes
(and for adding objects). This requires rocker to preallocate memory
needed for the commit up front in the prepare phase. Since rtnl_lock is
held between prepare-commit, store the allocated memory on a queue hanging
off of the rocker_port. Also, in prepare phase, do everything right up to
calling into HW. The same code paths are tranversed in the driver for both
prepare and commit phases. In some cases, any state modified in the
prepare phase must be reverted before returning so the commit phase makes
the same decisions.
As a consequence of holding rtnl_lock in process context for all attr sets
(and obj adds), all memory is GFP_KERNEL allocated and we don't need to
busy spin waiting for the device to complete the command. So the bulk of
this patch is simplifying the memory allocations to only use GFP_KERNEL and
to remove the nowait flag and busy spin loop.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch ID is just a gettable port attribute. Convert switchdev op
switchdev_parent_id_get to a switchdev attr.
Note: for sysfs and netlink interfaces, SWITCHDEV_ATTR_PORT_PARENT_ID is
called with SWITCHDEV_F_NO_RECUSE to limit switch ID user-visiblity to only
port netdevs. So when a port is stacked under bond/bridge, the user can
only query switch id via the switch ports, but not via the upper devices
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turned out that "switchdev" sticks. So just unify all related terms to use
this prefix.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turned out that "switchdev" sticks. So just unify all related terms to use
this prefix.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A small cleanup to make use of the ether_addr_equal helper.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -EINVAL from the invalid PCI region size error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Master change notifications may occur other than when joining or
leaving a bridge, for example when being added to or removed from
a bond or Open vSwitch.
Previously in those cases rocker_port_bridge_leave() was called
which results in a null-pointer dereference as rocker_port->bridge_dev
is NULL because there is no bridge device.
This patch makes provision for doing nothing in such cases.
Fixes: 6c70794500 ("rocker: implement L2 bridge offloading")
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the phys_port_name operation. Port names are pulled from the
rocker hardware model in qemu and default to the qemu name + port id.
e.g.,
sw1p1: flags=4098<BROADCAST,MULTICAST> mtu 1500
ether 52:54:00:12:35:01 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
where 'sw1' comes from the qemu command line -device rocker,name=sw1, and
'p1' is port 1.
Patch is adapted from Scott's phys_port_id patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hast to fix some sparse warning, I hard-coded a fix-sized array on the stack
which is probably too big for kernel standards. Fix this by converting array
to dynamic allocation.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move swdev wrappers over to new swdev ops (from previous ndo ops). No
functional changes to the implementation.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
rocker: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
dsa: move to new swdev ops
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass in the netlink flags (NLM_F_*) into switchdev driver for IPv4 FIB add op
to allow driver to 1) optimize hardware updates, 2) handle ip route prepend
and append commands correctly.
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver implements ndo_switch_fib_ipv4_add/del ops to add/del/mod IPv4
routes to/from switchdev device. Once a route is added to the device, and the
route's nexthops are resolved to neighbor MAC address, the device will forward
matching pkts rather than the kernel. This offloads the L3 forwarding path
from the kernel to the device. Note that control and management planes are
still mananged by Linux; only the data plane is offloaded. Standard routing
control protocols such as OSPF and BGP run on Linux and manage the kernel's FIB
via standard rtm netlink msgs...nothing changes here.
A new hash table is added to rocker to track neighbors. The driver listens for
neighbor updates events using netevent notifier NETEVENT_NEIGH_UPDATE. Any ARP
table updates for ports on this device are recorded in this table. Routes
installed to the device with nexthops that reference neighbors in this table
are "qualified". In the case of a route with nexthops not resolved in the
table, the kernel is asked to resolve the nexthop.
The driver uses fib_info->fib_priority for the priority field in rocker's
unicast routing table.
The device can only forward to pkts matching route dst to resolved nexthops.
Currently, the device only supports single-path routes (i.e. routes with one
nexthop). Equal Cost Multipath (ECMP) route support will be added in followup
patches.
This patch is driver support for unicast IPv4 routing only. Followup patches
will add driver and infrastructure for IPv6 routing and multicast routing.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
"val" is declared as a u64 so static checkers complain that this shift
can wrap. I don't have the hardware but probably it's doesn't have over
31 ports. Still we may as well silence the warning even if it's not a
real bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure kmalloc() succeeds.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the port forwarding state transitions for the cases when the port
joins or leaves a bridge, or is brought admin UP or DOWN. When port is
bridged, we can rely on bridge driver putting port in correct state using
STP callback into port driver, regardless if bridge is enabled for STP or not.
When port is not bridged, we can reuse some of the STP code to enabled or
disable forwarding depending on UP or DOWN.
Tested by trying all the transitions from bridge/not bridge, and UP/DOWN, and
verifying port is in the correct forwarding state after each transition.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just a rename of physical ports from "lport" to "pport". Not a
functional change. OF-DPA uses logical ports (lport) for tunnels, but the
driver (and device) were using "lport" for physical ports. Renaming physical
ports references to "pport", freeing up "lport" for use later with tunnels.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rocker device returns error codes if something goes wrong with descriptor
processing. Originally the device used standard errno codes for different
errors, but since those errno codes aren't portable across ARCHs, the device
now returns hard-coded error codes that stay constant across diff ARCHs. Fix
driver to use those same hard-coded values.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
