Commit Graph

3718 Commits

Author SHA1 Message Date
Tim Kryger
3cbc6123a9 mmc: sdhci: Set SDHCI_POWER_ON with external vmmc
Host controllers lacking the required internal vmmc regulator may still
follow the spec with regard to the LSB of SDHCI_POWER_CONTROL.  Set the
SDHCI_POWER_ON bit when vmmc is enabled to encourage the controller to
to drive CMD, DAT, SDCLK.

This fixes a regression observed on some Qualcomm and Nvidia boards
caused by 5222161 mmc: sdhci: Improve external VDD regulator support.

Fixes: 52221610dd (mmc: sdhci: Improve external VDD regulator support)
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Tested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-14 09:47:19 +01:00
Adrian Hunter
1f7f26528f mmc: sdhci-pci: Add support for Intel SPT
Add PCI IDs for SPT eMMC, SDIO and SD card.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-12 10:14:58 +01:00
Adrian Hunter
d0ed8e6b0a mmc: sdhci-acpi: Add ACPI HID INT344D
Add ACPI HID INT344D for an Intel SDIO host controller.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-12 10:14:57 +01:00
Krzysztof Kozlowski
2836766a9d mmc: sdhci: Fix sleep in atomic after inserting SD card
Sleep in atomic context happened on Trats2 board after inserting or
removing SD card because mmc_gpio_get_cd() was called under spin lock.

Fix this by moving card detection earlier, before acquiring spin lock.
The mmc_gpio_get_cd() call does not have to be protected by spin lock
because it does not access any sdhci internal data.
The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After
moving it out side of spin lock it could theoretically race with driver
removal but still there is no actual protection against manual card
eject.

Dmesg after inserting SD card:
[   41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511
[   41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1
[   41.677580] INFO: lockdep is turned off.
[   41.681486] irq event stamp: 61972
[   41.684872] hardirqs last  enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c
[   41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54
[   41.701190] softirqs last  enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8
[   41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114
[   41.716206] Preemption disabled at:[<  (null)>]   (null)
[   41.721500]
[   41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G        W      3.18.0-rc5-next-20141121 #883
[   41.732111] Workqueue: kmmcd mmc_rescan
[   41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14)
[   41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc)
[   41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30)
[   41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58)
[   41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4)
[   41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268)
[   41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0)
[   41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78)
[   41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124)
[   41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64)
[   41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4)
[   41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4)
[   41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0)
[   41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104)
[   41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[   42.038276] mmc0: new high speed SDHC card at address 1234

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 94144a465d ("mmc: sdhci: add get_cd() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-12 10:14:57 +01:00
Thomas Petazzoni
aa8165f914 mmc: sdhci-pxav3: do the mbus window configuration after enabling clocks
In commit 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada
38x SDHCI controller"), the sdhci-pxav3 driver was extended to include
support for the SDHCI controller found in the Armada 38x
processor. This mainly involved adding some MBus window related
configuration.

However, this configuration is currently done too early in ->probe():
it is done before clocks are enabled, while this configuration
involves touching the registers of the controller, which will hang the
SoC if the clock is disabled. It wasn't noticed until now because the
bootloader typically leaves gatable clocks enabled, but in situations
where we have a deferred probe (due to a CD GPIO that cannot be taken,
for example), then the probe will be re-tried later, after a clock
disable has been done in the exit path of the failed probe attempt of
the device. This second probe() will hang the system due to the clock
being disabled.

This can for example be produced on Armada 385 GP, which has a CD GPIO
connected to an I2C PCA9555. If the driver for the PCA9555 is not
compiled into the kernel, then we will have the following sequence of
events:

  1. The SDHCI probes
  2. It does the MBus configuration (which works, because the clock is
     left enabled by the bootloader)
  3. It enables the clock
  4. It tries to get the CD GPIO, which fails due to the driver being
     missing, so -EPROBE_DEFER is returned.
  5. Before returning -EPROBE_DEFER, the driver cleans up what was
     done, which includes disabling the clock.
  6. Later on, the SDHCI probe is tried again.
  7. It does the MBus configuration, which hangs because the clock is
     no longer enabled.

This commit does the obvious fix of doing the MBus configuration after
the clock has been enabled by the driver.

Fixes: 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-12 10:14:56 +01:00
Adrian Hunter
b5540ce151 mmc: sdhci: Disable re-tuning for HS400
Re-tuning for HS400 mode must be done in HS200
mode. Currently there is no support for that.
That needs to be reflected in the code.
Specifically, if tuning is executed in HS400 mode
then return an error, and do not start the
tuning timer if HS200 tuning is being done prior
to switching to HS400.

Note that periodic re-tuning is not expected
to be needed for HS400 but re-tuning is still
needed after the host controller has lost power.
In the case of suspend/resume that is not necessary
because the card is fully re-initialised. That
just leaves runtime suspend/resume with no support
for HS400 re-tuning.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-12 10:14:56 +01:00
Adrian Hunter
38e40bf5db mmc: sdhci: Simplify use of tuning timer
The tuning timer is always used if the tuning mode
is 1 and there is a tuning count, irrespective of
whether this is the first call, or any subsequent
call. Consequently the logic to start the timer
can be simplified.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-12 10:14:56 +01:00
Adrian Hunter
d519c863fc mmc: sdhci: Add out_unlock to sdhci_execute_tuning
A 'goto' can be used to save duplicating unlocking
and returning.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-12 10:14:55 +01:00
Adrian Hunter
ac00531d9f mmc: sdhci: Tuning should not change max_blk_count
Re-tuning requires that the maximum data length
is limited to 4MiB. The code currently changes
max_blk_count in an attempt to achieve that.
This is wrong because max_blk_count is a different
limit, but it is also un-necessary because
max_req_size is 512KiB anyway. Consequently, the
changes to max_blk_count are removed and the
comment for max_req_size adjusted accordingly.
The comment is also tweaked to show that the 512KiB
limit is a SDMA limit not an ADMA limit.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-01-12 10:14:55 +01:00
Alexandre Belloni
1c2d26e379 mmc: core: stop trying to switch width when only one bit is supported
mmc_select_bus_width() will try to switch to MMC_BUS_WIDTH_4 even if
MMC_CAP_4_BIT_DATA and MMC_CAP_8_BIT_DATA are not set in host->caps.
Return as soon as possible when those flags are not set

Fixes: 577fb13199 (mmc: rework selection of bus speed mode)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-29 14:49:28 +01:00
Linus Torvalds
c0f486fde3 More ACPI and power management updates for 3.19-rc1
- Fix a regression in leds-gpio introduced by a recent commit that
    inadvertently changed the name of one of the properties used by
    the driver (Fabio Estevam).
 
  - Fix a regression in the ACPI backlight driver introduced by a
    recent fix that missed one special case that had to be taken
    into account (Aaron Lu).
 
  - Drop the level of some new kernel messages from the ACPI core
    introduced by a recent commit to KERN_DEBUG which they should
    have used from the start and drop some other unuseful KERN_ERR
    messages printed by ACPI (Rafael J Wysocki).
 
  - Revert an incorrect commit modifying the cpupower tool
    (Prarit Bhargava).
 
  - Fix two regressions introduced by recent commits in the OPP
    library and clean up some existing minor issues in that code
    (Viresh Kumar).
 
  - Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
    the tree (or drop it where that can be done) in order to make
    it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
    Ulf Hansson, Ludovic Desroches).  There will be one more
    "CONFIG_PM_RUNTIME removal" batch after this one, because some
    new uses of it have been introduced during the current merge
    window, but that should be sufficient to finally get rid of it.
 
  - Make the ACPI EC driver more robust against race conditions
    related to GPE handler installation failures (Lv Zheng).
 
  - Prevent the ACPI device PM core code from attempting to
    disable GPEs that it has not enabled which confuses ACPICA
    and makes it report errors unnecessarily (Rafael J Wysocki).
 
  - Add a "force" command line switch to the intel_pstate driver
    to make it possible to override the blacklisting of some
    systems in that driver if needed (Ethan Zhao).
 
  - Improve intel_pstate code documentation and add a MAINTAINERS
    entry for it (Kristen Carlson Accardi).
 
  - Make the ACPI fan driver create cooling device interfaces
    witn names that reflect the IDs of the ACPI device objects
    they are associated with, except for "generic" ACPI fans
    (PNP ID "PNP0C0B").  That's necessary for user space thermal
    management tools to be able to connect the fans with the
    parts of the system they are supposed to be cooling properly.
    From Srinivas Pandruvada.
 
 /
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABCAAGBQJUk0IDAAoJEILEb/54YlRx7fgP/3+yF/0TnEW93j2ALDAQFiLF
 tSv2A2vQC8vtMJjjWx0z/HqPh86gfaReEFZmUJD/Q/e2LXEnxNZJ+QMjcekPVkDM
 mTvcIMc2MR8vOA/oMkgxeaKregrrx7RkCfojd+NWZhVukkjl+mvBHgAnYjXRL+NZ
 unDWGlbHG97vq/3kGjPYhDS00nxHblw8NHFBu5HL5RxwABdWoeZJITwqxXWyuPLw
 nlqNWlOxmwvtSbw2VMKz0uof1nFHyQLykYsMG0ZsyayCRdWUZYkEqmE7GGpCLkLu
 D6yfmlpen6ccIOsEAae0eXBt50IFY9Tihk5lovx1mZmci2SNRg29BqMI105wIn0u
 8b8Ej7MNHp7yMxRpB5WfU90p/y7ioJns9guFZxY0CKaRnrI2+BLt3RscMi3MPI06
 Cu2/WkSSa09fhDPA+pk+VDYsmWgyVawigesNmMP5/cvYO/yYywVRjOuO1k77qQGp
 4dSpFYEHfpxinejZnVZOk2V9MkvSLoSMux6wPV0xM0IE1iD0ulVpHjTJrwp80ph4
 +bfUFVr/vrD1y7EKbf1PD363ZKvJhWhvQWDgETsM1vgLf21PfWO7C2kflIAsWsdQ
 1ukD5nCBRlP4K73hG7bdM6kRztXhUdR0SHg85/t0KB/ExiVqtcXIzB60D0G1lENd
 QlKbq3O4lim1WGuhazQY
 =5fo2
 -----END PGP SIGNATURE-----

Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull more ACPI and power management updates from Rafael Wysocki:
 "These are regression fixes (leds-gpio, ACPI backlight driver,
  operating performance points library, ACPI device enumeration
  messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
  PM), some cleanups in the operating performance points (OPP)
  framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
  minor intel_pstate driver changes, a new MAINTAINERS entry for it and
  an ACPI fan driver change needed for better support of thermal
  management in user space.

  Specifics:

   - Fix a regression in leds-gpio introduced by a recent commit that
     inadvertently changed the name of one of the properties used by the
     driver (Fabio Estevam).

   - Fix a regression in the ACPI backlight driver introduced by a
     recent fix that missed one special case that had to be taken into
     account (Aaron Lu).

   - Drop the level of some new kernel messages from the ACPI core
     introduced by a recent commit to KERN_DEBUG which they should have
     used from the start and drop some other unuseful KERN_ERR messages
     printed by ACPI (Rafael J Wysocki).

   - Revert an incorrect commit modifying the cpupower tool (Prarit
     Bhargava).

   - Fix two regressions introduced by recent commits in the OPP library
     and clean up some existing minor issues in that code (Viresh
     Kumar).

   - Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
     tree (or drop it where that can be done) in order to make it
     possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
     Hansson, Ludovic Desroches).

     There will be one more "CONFIG_PM_RUNTIME removal" batch after this
     one, because some new uses of it have been introduced during the
     current merge window, but that should be sufficient to finally get
     rid of it.

   - Make the ACPI EC driver more robust against race conditions related
     to GPE handler installation failures (Lv Zheng).

   - Prevent the ACPI device PM core code from attempting to disable
     GPEs that it has not enabled which confuses ACPICA and makes it
     report errors unnecessarily (Rafael J Wysocki).

   - Add a "force" command line switch to the intel_pstate driver to
     make it possible to override the blacklisting of some systems in
     that driver if needed (Ethan Zhao).

   - Improve intel_pstate code documentation and add a MAINTAINERS entry
     for it (Kristen Carlson Accardi).

   - Make the ACPI fan driver create cooling device interfaces witn
     names that reflect the IDs of the ACPI device objects they are
     associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").

     That's necessary for user space thermal management tools to be able
     to connect the fans with the parts of the system they are supposed
     to be cooling properly.  From Srinivas Pandruvada"

* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
  MAINTAINERS: add entry for intel_pstate
  ACPI / video: update the skip case for acpi_video_device_in_dod()
  power / PM: Eliminate CONFIG_PM_RUNTIME
  NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  ACPI / EC: Fix unexpected ec_remove_handlers() invocations
  Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
  tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
  PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
  mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
  PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
  ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  ACPI / PM: Do not disable wakeup GPEs that have not been enabled
  ACPI / utils: Drop error messages from acpi_evaluate_reference()
  ...
2014-12-18 20:28:33 -08:00
Linus Torvalds
e6b5be2be4 Driver core patches for 3.19-rc1
Here's the set of driver core patches for 3.19-rc1.
 
 They are dominated by the removal of the .owner field in platform
 drivers.  They touch a lot of files, but they are "simple" changes, just
 removing a line in a structure.
 
 Other than that, a few minor driver core and debugfs changes.  There are
 some ath9k patches coming in through this tree that have been acked by
 the wireless maintainers as they relied on the debugfs changes.
 
 Everything has been in linux-next for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
 53kAoLeteByQ3iVwWurwwseRPiWa8+MI
 =OVRS
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core update from Greg KH:
 "Here's the set of driver core patches for 3.19-rc1.

  They are dominated by the removal of the .owner field in platform
  drivers.  They touch a lot of files, but they are "simple" changes,
  just removing a line in a structure.

  Other than that, a few minor driver core and debugfs changes.  There
  are some ath9k patches coming in through this tree that have been
  acked by the wireless maintainers as they relied on the debugfs
  changes.

  Everything has been in linux-next for a while"

* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
  Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
  fs: debugfs: add forward declaration for struct device type
  firmware class: Deletion of an unnecessary check before the function call "vunmap"
  firmware loader: fix hung task warning dump
  devcoredump: provide a one-way disable function
  device: Add dev_<level>_once variants
  ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
  ath: use seq_file api for ath9k debugfs files
  debugfs: add helper function to create device related seq_file
  drivers/base: cacheinfo: remove noisy error boot message
  Revert "core: platform: add warning if driver has no owner"
  drivers: base: support cpu cache information interface to userspace via sysfs
  drivers: base: add cpu_device_create to support per-cpu devices
  topology: replace custom attribute macros with standard DEVICE_ATTR*
  cpumask: factor out show_cpumap into separate helper function
  driver core: Fix unbalanced device reference in drivers_probe
  driver core: fix race with userland in device_add()
  sysfs/kernfs: make read requests on pre-alloc files use the buffer.
  sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
  fs: sysfs: return EGBIG on write if offset is larger than file size
  ...
2014-12-14 16:10:09 -08:00
Ludovic Desroches
c3cb6ba415 mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
The currently used SET_PM_RUNTIME_PM_OPS() macro is defined to the
SET_RUNTIME_PM_OPS() macro. Convert to the later, since that's the
proper one to use.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-12-13 00:44:11 +01:00
Linus Torvalds
92a578b064 ACPI and power management updates for 3.19-rc1
This time we have some more new material than we used to have during
 the last couple of development cycles.
 
 The most important part of it to me is the introduction of a unified
 interface for accessing device properties provided by platform
 firmware.  It works with Device Trees and ACPI in a uniform way and
 drivers using it need not worry about where the properties come
 from as long as the platform firmware (either DT or ACPI) makes
 them available.  It covers both devices and "bare" device node
 objects without struct device representation as that turns out to
 be necessary in some cases.  This has been in the works for quite
 a few months (and development cycles) and has been approved by
 all of the relevant maintainers.
 
 On top of that, some drivers are switched over to the new interface
 (at25, leds-gpio, gpio_keys_polled) and some additional changes are
 made to the core GPIO subsystem to allow device drivers to manipulate
 GPIOs in the "canonical" way on platforms that provide GPIO information
 in their ACPI tables, but don't assign names to GPIO lines (in which
 case the driver needs to do that on the basis of what it knows about
 the device in question).  That also has been approved by the GPIO
 core maintainers and the rfkill driver is now going to use it.
 
 Second is support for hardware P-states in the intel_pstate driver.
 It uses CPUID to detect whether or not the feature is supported by
 the processor in which case it will be enabled by default.  However,
 it can be disabled entirely from the kernel command line if necessary.
 
 Next is support for a platform firmware interface based on ACPI
 operation regions used by the PMIC (Power Management Integrated
 Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
 That interface is used for manipulating power resources and for
 thermal management: sensor temperature reporting, trip point setting
 and so on.
 
 Also the ACPI core is now going to support the _DEP configuration
 information in a limited way.  Basically, _DEP it supposed to reflect
 off-the-hierarchy dependencies between devices which may be very
 indirect, like when AML for one device accesses locations in an
 operation region handled by another device's driver (usually, the
 device depended on this way is a serial bus or GPIO controller).
 The support added this time is sufficient to make the ACPI battery
 driver work on Asus T100A, but it is general enough to be able to
 cover some other use cases in the future.
 
 Finally, we have a new cpufreq driver for the Loongson1B processor.
 
 In addition to the above, there are fixes and cleanups all over the
 place as usual and a traditional ACPICA update to a recent upstream
 release.
 
 As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
 for Intel platforms should be able to handle power management of
 the DMA engine correctly, the cpufreq-dt driver should interact
 with the thermal subsystem in a better way and the ACPI backlight
 driver should handle some more corner cases, among other things.
 
 On top of the ACPICA update there are fixes for race conditions
 in the ACPICA's interrupt handling code which might lead to some
 random and strange looking failures on some systems.
 
 In the cleanups department the most visible part is the series
 of commits targeted at getting rid of the CONFIG_PM_RUNTIME
 configuration option.  That was triggered by a discussion
 regarding the generic power domains code during which we realized
 that trying to support certain combinations of PM config options
 was painful and not really worth it, because nobody would use them
 in production anyway.  For this reason, we decided to make
 CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
 conclusion that the latter became redundant and CONFIG_PM could
 be used instead of it.  The material here makes that replacement
 in a major part of the tree, but there will be at least one more
 batch of that in the second part of the merge window.
 
 Specifics:
 
  - Support for retrieving device properties information from ACPI
    _DSD device configuration objects and a unified device properties
    interface for device drivers (and subsystems) on top of that.
    As stated above, this works with Device Trees and ACPI and allows
    device drivers to be written in a platform firmware (DT or ACPI)
    agnostic way.  The at25, leds-gpio and gpio_keys_polled drivers
    are now going to use this new interface and the GPIO subsystem
    is additionally modified to allow device drivers to assign names
    to GPIO resources returned by ACPI _CRS objects (in case _DSD is
    not present or does not provide the expected data).  The changes
    in this set are mostly from Mika Westerberg, Rafael J Wysocki,
    Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
    Geert Uytterhoeven).
 
  - Support for Hardware Managed Performance States (HWP) as described
    in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
    driver.  CPUID is used to detect whether or not the feature is
    supported by the processor.  If supported, it will be enabled
    automatically unless the intel_pstate=no_hwp switch is present in
    the kernel command line.  From Dirk Brandewie.
 
  - New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
 
  - Support for firmware interface based on ACPI operation regions
    used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
    platforms for power resource control and thermal management
    (Aaron Lu).
 
  - Limited support for retrieving off-the-hierarchy dependencies
    between devices from ACPI _DEP device configuration objects
    and deferred probing support for the ACPI battery driver based
    on the _DEP information to make that driver work on Asus T100A
    (Lan Tianyu).
 
  - New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
 
  - ACPICA update to upstream revision 20141107 which only affects
    tools (Bob Moore).
 
  - Fixes for race conditions in the ACPICA's interrupt handling
    code and in the ACPI code related to system suspend and resume
    (Lv Zheng and Rafael J Wysocki).
 
  - ACPI core fix for an RCU-related issue in the ioremap() regions
    management code that slowed down significantly after CPUs had
    been allowed to enter idle states even if they'd had RCU callbakcs
    queued and triggered some problems in certain proprietary graphics
    driver (and elsewhere).  The fix replaces synchronize_rcu() in
    that code with synchronize_rcu_expedited() which makes the issue
    go away.  From Konstantin Khlebnikov.
 
  - ACPI LPSS (Low-Power Subsystem) driver fix to handle power
    management of the DMA engine included into the LPSS correctly.
    The problem is that the DMA engine doesn't have ACPI PM support
    of its own and it simply is turned off when the last LPSS device
    having ACPI PM support goes into D3cold.  To work around that,
    the PM domain used by the ACPI LPSS driver is redesigned so at
    least one device with ACPI PM support will be on as long as the
    DMA engine is in use.  From Andy Shevchenko.
 
  - ACPI backlight driver fix to avoid using it on "Win8-compatible"
    systems where it doesn't work and where it was used by default by
    mistake (Aaron Lu).
 
  - Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
    Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
    Ashwin Chaugule (mostly related to the upcoming ARM64 support).
 
  - Intel RAPL (Running Average Power Limit) power capping driver
    fixes and improvements including new processor IDs (Jacob Pan).
 
  - Generic power domains modification to power up domains after
    attaching devices to them to meet the expectations of device
    drivers and bus types assuming devices to be accessible at
    probe time (Ulf Hansson).
 
  - Preliminary support for controlling device clocks from the
    generic power domains core code and modifications of the
    ARM/shmobile platform to use that feature (Ulf Hansson).
 
  - Assorted minor fixes and cleanups of the generic power
    domains core code (Ulf Hansson, Geert Uytterhoeven).
 
  - Assorted minor fixes and cleanups of the device clocks control
    code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
 
  - Consolidation of device power management Kconfig options by making
    CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
    which is now redundant (Rafael J Wysocki and Kevin Hilman).  That
    is the first batch of the changes needed for this purpose.
 
  - Core device runtime power management support code cleanup related
    to the execution of callbacks (Andrzej Hajda).
 
  - cpuidle ARM support improvements (Lorenzo Pieralisi).
 
  - cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
    a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
    Bartlomiej Zolnierkiewicz).
 
  - New cpufreq driver callback (->ready) to be executed when the
    cpufreq core is ready to use a given policy object and cpufreq-dt
    driver modification to use that callback for cooling device
    registration (Viresh Kumar).
 
  - cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
    James Geboski, Tomeu Vizoso).
 
  - Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
    cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
    Stefan Wahren, Petr Cvek).
 
  - OPP (Operating Performance Points) framework modification to
    allow OPPs to be removed too and update of a few cpufreq drivers
    (cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
    during initialization) on driver removal (Viresh Kumar).
 
  - Hibernation core fixes and cleanups (Tina Ruchandani and
    Markus Elfring).
 
  - PM Kconfig fix related to CPU power management (Pankaj Dubey).
 
  - cpupower tool fix (Prarit Bhargava).
 
 /
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABCAAGBQJUhj6JAAoJEILEb/54YlRxTM4P/j5g5SfqvY0QKsn7sR7MGZ6v
 nsgCBhJAqTw3ocNC7EAs8z9h2GWy1KbKpakKYWAh9Fs1yZoey7tFSlcv/Rgjlp70
 uU5sDQHtpE9mHKiymdsowiQuWgpl962L4k+k8hUslhlvgk1PvVbpajR6OqG8G+pD
 asuIW9eh1APNkLyXmRJ3ZPomzs0VmRdZJ0NEs0lKX9mJskqEvxPIwdaxq3iaJq9B
 Fo0J345zUDcJnxWblDRdHlOigCimglElfN5qJwaC4KpwUKuBvLRKbp4f69+wfT0c
 kYFiR29X5KjJ2kLfP/wKsLyuDCYYXRq3tCia5M1tAqOjZ+UA89H/GDftx/5lntmv
 qUlBa35VfdS1SX4HyApZitOHiLgo+It/hl8Z9bJnhyVw66NxmMQ8JYN2imb8Lhqh
 XCLR7BxLTah82AapLJuQ0ZDHPzZqMPG2veC2vAzRMYzVijict/p4Y2+qBqONltER
 4rs9uRVn+hamX33lCLg8BEN8zqlnT3rJFIgGaKjq/wXHAU/zpE9CjOrKMQcAg9+s
 t51XMNPwypHMAYyGVhEL89ImjXnXxBkLRuquhlmEpvQchIhR+mR3dLsarGn7da44
 WPIQJXzcsojXczcwwfqsJCR4I1FTFyQIW+UNh02GkDRgRovQqo+Jk762U7vQwqH+
 LBdhvVaS1VW4v+FWXEoZ
 =5dox
 -----END PGP SIGNATURE-----

Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull ACPI and power management updates from Rafael Wysocki:
 "This time we have some more new material than we used to have during
  the last couple of development cycles.

  The most important part of it to me is the introduction of a unified
  interface for accessing device properties provided by platform
  firmware.  It works with Device Trees and ACPI in a uniform way and
  drivers using it need not worry about where the properties come from
  as long as the platform firmware (either DT or ACPI) makes them
  available.  It covers both devices and "bare" device node objects
  without struct device representation as that turns out to be necessary
  in some cases.  This has been in the works for quite a few months (and
  development cycles) and has been approved by all of the relevant
  maintainers.

  On top of that, some drivers are switched over to the new interface
  (at25, leds-gpio, gpio_keys_polled) and some additional changes are
  made to the core GPIO subsystem to allow device drivers to manipulate
  GPIOs in the "canonical" way on platforms that provide GPIO
  information in their ACPI tables, but don't assign names to GPIO lines
  (in which case the driver needs to do that on the basis of what it
  knows about the device in question).  That also has been approved by
  the GPIO core maintainers and the rfkill driver is now going to use
  it.

  Second is support for hardware P-states in the intel_pstate driver.
  It uses CPUID to detect whether or not the feature is supported by the
  processor in which case it will be enabled by default.  However, it
  can be disabled entirely from the kernel command line if necessary.

  Next is support for a platform firmware interface based on ACPI
  operation regions used by the PMIC (Power Management Integrated
  Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
  That interface is used for manipulating power resources and for
  thermal management: sensor temperature reporting, trip point setting
  and so on.

  Also the ACPI core is now going to support the _DEP configuration
  information in a limited way.  Basically, _DEP it supposed to reflect
  off-the-hierarchy dependencies between devices which may be very
  indirect, like when AML for one device accesses locations in an
  operation region handled by another device's driver (usually, the
  device depended on this way is a serial bus or GPIO controller).  The
  support added this time is sufficient to make the ACPI battery driver
  work on Asus T100A, but it is general enough to be able to cover some
  other use cases in the future.

  Finally, we have a new cpufreq driver for the Loongson1B processor.

  In addition to the above, there are fixes and cleanups all over the
  place as usual and a traditional ACPICA update to a recent upstream
  release.

  As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
  Intel platforms should be able to handle power management of the DMA
  engine correctly, the cpufreq-dt driver should interact with the
  thermal subsystem in a better way and the ACPI backlight driver should
  handle some more corner cases, among other things.

  On top of the ACPICA update there are fixes for race conditions in the
  ACPICA's interrupt handling code which might lead to some random and
  strange looking failures on some systems.

  In the cleanups department the most visible part is the series of
  commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
  option.  That was triggered by a discussion regarding the generic
  power domains code during which we realized that trying to support
  certain combinations of PM config options was painful and not really
  worth it, because nobody would use them in production anyway.  For
  this reason, we decided to make CONFIG_PM_SLEEP select
  CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
  became redundant and CONFIG_PM could be used instead of it.  The
  material here makes that replacement in a major part of the tree, but
  there will be at least one more batch of that in the second part of
  the merge window.

  Specifics:

   - Support for retrieving device properties information from ACPI _DSD
     device configuration objects and a unified device properties
     interface for device drivers (and subsystems) on top of that.  As
     stated above, this works with Device Trees and ACPI and allows
     device drivers to be written in a platform firmware (DT or ACPI)
     agnostic way.  The at25, leds-gpio and gpio_keys_polled drivers are
     now going to use this new interface and the GPIO subsystem is
     additionally modified to allow device drivers to assign names to
     GPIO resources returned by ACPI _CRS objects (in case _DSD is not
     present or does not provide the expected data).  The changes in
     this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
     Lu, and Darren Hart with some fixes from others (Fabio Estevam,
     Geert Uytterhoeven).

   - Support for Hardware Managed Performance States (HWP) as described
     in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
     driver.  CPUID is used to detect whether or not the feature is
     supported by the processor.  If supported, it will be enabled
     automatically unless the intel_pstate=no_hwp switch is present in
     the kernel command line.  From Dirk Brandewie.

   - New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).

   - Support for firmware interface based on ACPI operation regions used
     by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
     platforms for power resource control and thermal management (Aaron
     Lu).

   - Limited support for retrieving off-the-hierarchy dependencies
     between devices from ACPI _DEP device configuration objects and
     deferred probing support for the ACPI battery driver based on the
     _DEP information to make that driver work on Asus T100A (Lan
     Tianyu).

   - New cpufreq driver for the Loongson1B processor (Kelvin Cheung).

   - ACPICA update to upstream revision 20141107 which only affects
     tools (Bob Moore).

   - Fixes for race conditions in the ACPICA's interrupt handling code
     and in the ACPI code related to system suspend and resume (Lv Zheng
     and Rafael J Wysocki).

   - ACPI core fix for an RCU-related issue in the ioremap() regions
     management code that slowed down significantly after CPUs had been
     allowed to enter idle states even if they'd had RCU callbakcs
     queued and triggered some problems in certain proprietary graphics
     driver (and elsewhere).  The fix replaces synchronize_rcu() in that
     code with synchronize_rcu_expedited() which makes the issue go
     away.  From Konstantin Khlebnikov.

   - ACPI LPSS (Low-Power Subsystem) driver fix to handle power
     management of the DMA engine included into the LPSS correctly.  The
     problem is that the DMA engine doesn't have ACPI PM support of its
     own and it simply is turned off when the last LPSS device having
     ACPI PM support goes into D3cold.  To work around that, the PM
     domain used by the ACPI LPSS driver is redesigned so at least one
     device with ACPI PM support will be on as long as the DMA engine is
     in use.  From Andy Shevchenko.

   - ACPI backlight driver fix to avoid using it on "Win8-compatible"
     systems where it doesn't work and where it was used by default by
     mistake (Aaron Lu).

   - Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
     Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
     Chaugule (mostly related to the upcoming ARM64 support).

   - Intel RAPL (Running Average Power Limit) power capping driver fixes
     and improvements including new processor IDs (Jacob Pan).

   - Generic power domains modification to power up domains after
     attaching devices to them to meet the expectations of device
     drivers and bus types assuming devices to be accessible at probe
     time (Ulf Hansson).

   - Preliminary support for controlling device clocks from the generic
     power domains core code and modifications of the ARM/shmobile
     platform to use that feature (Ulf Hansson).

   - Assorted minor fixes and cleanups of the generic power domains core
     code (Ulf Hansson, Geert Uytterhoeven).

   - Assorted minor fixes and cleanups of the device clocks control code
     in the PM core (Geert Uytterhoeven, Grygorii Strashko).

   - Consolidation of device power management Kconfig options by making
     CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
     which is now redundant (Rafael J Wysocki and Kevin Hilman).  That
     is the first batch of the changes needed for this purpose.

   - Core device runtime power management support code cleanup related
     to the execution of callbacks (Andrzej Hajda).

   - cpuidle ARM support improvements (Lorenzo Pieralisi).

   - cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
     new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
     Bartlomiej Zolnierkiewicz).

   - New cpufreq driver callback (->ready) to be executed when the
     cpufreq core is ready to use a given policy object and cpufreq-dt
     driver modification to use that callback for cooling device
     registration (Viresh Kumar).

   - cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
     Geboski, Tomeu Vizoso).

   - Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
     cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
     Stefan Wahren, Petr Cvek).

   - OPP (Operating Performance Points) framework modification to allow
     OPPs to be removed too and update of a few cpufreq drivers
     (cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
     during initialization) on driver removal (Viresh Kumar).

   - Hibernation core fixes and cleanups (Tina Ruchandani and Markus
     Elfring).

   - PM Kconfig fix related to CPU power management (Pankaj Dubey).

   - cpupower tool fix (Prarit Bhargava)"

* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
  i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
  dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  tools: cpupower: fix return checks for sysfs_get_idlestate_count()
  drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
  MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  leds: leds-gpio: Fix multiple instances registration without 'label' property
  iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
  block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
  PM: Merge the SET*_RUNTIME_PM_OPS() macros
  ...
2014-12-10 21:17:00 -08:00
Ulf Hansson
33d73935e4 mmc: sdhci-msm: Convert to mmc_send_tuning()
Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API instead.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Georgi Djakov <gdjakov@mm-sol.com>
Acked-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
2014-12-08 09:21:06 +01:00
Ulf Hansson
d178532689 mmc: sdhci-esdhc-imx: Convert to mmc_send_tuning()
Instead of having a local function taking care of sending the tuning
command, let's use the common mmc_send_tuning() API provided by the mmc
core. In this way the request will be handled as any other request by
sdhci core.

As an effect of this change, the pm_runtime_get_sync() call at
esdhc_prepare_tuning() isn't needed any more.

This patch will also introduce another change in behavior, since before
the response pattern to the tuning command wasn't verified by
sdhci-esdhc-imx. The mmc_send_tuning() does that.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
2014-12-08 09:20:47 +01:00
Ulf Hansson
fe5afb13d4 mmc: core: Let mmc_send_tuning() to take struct mmc_host* as parameter
To be able to use mmc_send_tuning() prior the struct mmc_card has been
allocated, let's convert it to take the struct mmc_host* as parameter
instead.

Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Dong Aisheng <b29396@freescale.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
2014-12-08 09:11:04 +01:00
Bhuvanesh Surachari
fdb409f636 mmc: queue: Improve error handling during allocation of bounce buffers
Allocation of previous bounce buffer in mmc_init_queue when the current
bounce buffer allocation fails was leading to a crash later in
__blk_segment_map_sg. Error handling is improved by allocating previous
bounce buffer only if the current bounce buffer allocation succeeds.

Signed-off-by: Bhuvanesh Surachari <bhuvanesh_surachari@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-05 10:33:17 +01:00
Rafael J. Wysocki
162d6f9800 MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.

Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mmc/.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-05 03:05:33 +01:00
Rafael J. Wysocki
6ed23b806e PM: Merge the SET*_RUNTIME_PM_OPS() macros
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.

However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.

For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.

Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2014-12-04 00:51:30 +01:00
Adrian Hunter
9d65cb88e5 mmc: sdhci-acpi: Add two host capabilities for Intel
Intel host controllers are capable of doing the bus
width test and of waiting while busy, so add the
capability flags.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-02 12:25:29 +01:00
Adrian Hunter
6aab23a8f7 mmc: sdhci-pci: Add two host capabilities for BYT
BYT host controllers are capable of doing the bus
width test and of waiting while busy, so add the
capability flags.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-02 12:25:29 +01:00
Adrian Hunter
e1f5633ad4 mmc: sdhci-acpi: Add SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC actually causes
standard-compliant behaviour by causing the flagging
of the last DMA transfer descriptor as the end
instead of there being an additional nop descriptor
which is flagged as the end.  Consequently, it is
better to have the quirk.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-02 12:25:29 +01:00
Adrian Hunter
db6e8cdfcd mmc: sdhci-pci: Add SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC to BYT
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC actually causes
standard-compliant behaviour by causing the flagging
of the last DMA transfer descriptor as the end
instead of there being an additional nop descriptor
which is flagged as the end.  Consequently, it is
better to have the quirk.  Add it for BYT.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-02 12:25:29 +01:00
ludovic.desroches@atmel.com
467e081d23 mmc: atmel-mci: use probe deferring if dma controller is not ready yet
Return probe defer if requesting a dma channel without a dma controller
probed.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-02 11:08:33 +01:00
ludovic.desroches@atmel.com
5e0fe89740 mmc: atmel-mci: stop using specific initcall
No more use late initcall to manage probing order. Use probe deferring
if needed.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-02 11:01:35 +01:00
ludovic.desroches@atmel.com
ab050b9269 mmc: atmel-mci: remove __init/__exit attributes
Using __init/__exit attributes can cause several breakages so remove
them.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-02 11:01:06 +01:00
ludovic.desroches@atmel.com
1c7615b90c mmc: atmel-mci: remove useless DMA stuff for non-dt devices
All devices with a DMA controller are DT compliant and legacy support
has been removed. For those reasons, some DMA stuff is useless.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-12-02 11:00:31 +01:00
Ulf Hansson
903101a839 mmc: omap_hsmmc: Fix UHS card with DDR50 support
The commit, mmc: omap: clarify DDR timing mode between SD-UHS and eMMC,
switched omap_hsmmc to support MMC DDR mode instead of UHS DDR50 mode.

Add UHS DDR50 mode again and this time let's also keep the MMC DDR mode.

Fixes: 5438ad95a5 (mmc: omap: clarify DDR timing mode between SD-UHS and eMMC)
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:40:39 +01:00
Minda Chen
996903de92 mmc: core: add core-level function for sending tuning commands
According to the SD card spec, Add a manual tuning command function
for SDR104/HS200.
Sending command 19 or command 21 to read data and compare with the
tunning block pattern.

This patch will help to decrease some platform private codes in SDHCI
platform_execute_tuning() callbacks.

Signed-off-by: Minda Chen <Minda.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:36:51 +01:00
Vincent Yang
c6eb588028 mmc: core: hold SD Clock before CMD11 during Signal
Voltage Switch Procedure

This patch is to fix an issue found on mb86s7x platforms.

[symptom]
There are some UHS-1 SD memory cards sometimes cannot be detected correctly,
e.g., Transcend 600x SDXC 64GB UHS-1 memory card.
During Signal Voltage Switch Procedure, failure to switch is indicated
by the card holding DAT[3:0] low.

[analysis]
According to SD Host Controller Simplified Specification Version 3.00
chapter 3.6.1, the Signal Voltage Switch Procedure should be:
(1) Check S18A; (2) Issue CMD11; (3) Check CMD 11 response;
(4) Stop providing SD clock; (5) Check DAT[3:0] should be 0000b;
(6) Set 1.8V Signal Enable; (7) Wait 5ms; (8) Check 1.8V Signal Enable;
(9) Provide SD Clock; (10) Wait 1ms; (11) Check DAT[3:0] should be 1111b;
(12) error handling

With CONFIG_MMC_CLKGATE=y, sometimes there is one more gating/un-gating
SD clock between (2) and (3). In this case, some UHS-1 SD cards will hold
DAT[3:0] 0000b at (11) and thus fails Signal Voltage Switch Procedure.

[solution]
By mmc_host_clk_hold() before CMD11, the additional gating/un-gating
SD clock between (2) and (3) can be prevented and thus no failure at (11).
It has been verified with many UHS-1 SD cards on mb86s7x platforms and
works correctly.

Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Reviewed-by: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:05 +01:00
Fabio Estevam
e34d467c51 mmc: mxs-mmc: Check for clk_prepare_enable() error
clk_prepare_enable() may fail and in this case we should propagate the error.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:04 +01:00
Fabio Estevam
5654d90064 mmc: mxs-mmc: Propagate the real error
If platform_get_irq() fails, it is better to propagate the real error value
instead of a 'fake' one.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:04 +01:00
Fabio Estevam
c3cd5c076c mmc: mxs-mmc: No need to do NULL check on 'iores'
devm_ioremap_resource() already checks if 'iores' is NULL or not, so we can
skip this manual check.

While at it, move platform_get_resource() closer to devm_ioremap_resource() for
better readability.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:03 +01:00
Andrew Bresticker
4d7c07cd6c mmc: dw_mmc: Add support for IMG Pistachio
Add support for the DW MMC host found on the Imagination Pistachio SoC.
Like the DW MMC hosts found on SOCFPGA and Rockchip SoCs, the DW MMC
host on Pistachio requires the use of SDMMC_CMD_USE_HOLD_REG.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:03 +01:00
Fabio Estevam
d13552908b mmc: mxs-mmc: Simplify PM hooks
By using SIMPLE_DEV_PM_OPS we can make the code smaller and cleaner.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:02 +01:00
Fabio Estevam
cc87a358c5 mmc: mxs-mmc: Register the irq with the device name
Instead of registering the irq name with the driver's name, it's better to pass
the device name so that we have a more explicit indication as to what mmc
instance the irq is related:

$ cat /proc/interrupts
           CPU0
...
 26:          6         -  96  80010000.ssp

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:02 +01:00
James Hogan
66dfd10173 mmc: dw_mmc: avoid write to CDTHRCTL on older versions
Commit f1d2736c81 (mmc: dw_mmc: control card read threshold) added
dw_mci_ctrl_rd_thld() with an unconditional write to the CDTHRCTL
register at offset 0x100. However before version 240a, the FIFO region
started at 0x100, so the write messes with the FIFO and completely
breaks the driver.

If the version id < 240A, return early from dw_mci_ctl_rd_thld() so as
not to hit this problem.

Fixes: f1d2736c81 (mmc: dw_mmc: control card read threshold)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.13+
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:02 +01:00
Dan Carpenter
9e2a0c96ef mmc: toshsd: move dereference below check for NULL
We check for NULL pointers after dereferencing so it's too late.  Oddly
enough, Smatch misses this code but complains about the caller passing
NULL pointers to this function:

	drivers/mmc/host/toshsd.c:389 toshsd_irq()
	error: we previously assumed 'host->cmd' could be null (see line 349)

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:01 +01:00
ludovic.desroches@atmel.com
ecb89f2f5f mmc: atmel-mci: remove compat for non DT board when requesting dma chan
All boards with a dma controller have DT support so using
dma_request_slave_channel_compat is no more needed.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:01 +01:00
Addy Ke
767562348b mmc: dw_mmc: add support for the other bit of sdio interrupt
The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.

Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:00 +01:00
Andrew Lunn
3c583f70a8 mmc: mvsdio: Work around broken TX DMA
In order to use the mvsdio driver for sdio, it has been necessary to
use a module parameter to disable DMA so to force PIO is used. It is
then possible to use wireless LAN devices like mwifiex found on
topkick and mirabox. However, accessing an MMC SD card does work with
DMA.

Investigation has shown that MMC block device accesses are always
aligned to 64 byte boundaries, where as transfers from mwifiex are
rarely more than word aligned. It has also been determined that card
to host transfers work with DMA for SDIO devices, but host to card
transfers with DMA have problems.

This patch extends the current checks for buffers which are not word
aligned or multiple of words. All host to card transfers which are not
64 byte aligned are now also performed via PIO. This should not affect
the performance of SD cards, but allow sdio devices to work out of the
box, and they are likely to be more efficient since DMA will be used
for card to host transfers.

Tested on mirabox for wifi via mwifiex
Tested on 370 RD for file systems on an SD card.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:31:00 +01:00
Ben Hutchings
a26eba614a mmc: block: Increase max_devices
Currently the driver imposes a limit of 256 total minor numbers,
apparently based on the historic Unix/Linux limit.  This is quite
restrictive, particularly if we raise the maximum number of
partitions per card to 256 to match sd.

In order to make the full minor number space available we would
have to replace the static dev_use and name_use arrays with struct
ida.  But we can at least allow use of 256 cards rather than just
256 minors, with only a small change.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:30:59 +01:00
Alim Akhtar
c34346b200 mmc: dw_mmc: add support for ARM64
There are upcoming ARM64 SoCs with dw_mmc host controller.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:30:59 +01:00
NeilBrown
006fc51cb3 mmc: core: reset sdio card properly on resume.
mmc_sdio_power_restore() calls
	mmc_send_if_cond(host, host->card->ocr);

	ret = mmc_send_io_op_cond(host, 0, NULL);

between mmc_go_idle() and mmc_sdio_init_card().
mmc_sdio_resume() needs to as well, else my libertas sdio wifi
device doesn't resume properly from suspend.

Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:30:59 +01:00
NeilBrown
59b6c9e0ad mmc: core: use card->ocr when negotiating voltage setting in mmc_sdio_power_restore
As we are restoring power to a known card, it makes sense to use
the 'ocr' value known for the card rather than the generic one
for the host interface.
This matches the use of card->ocr passed to mmc_power_up in
mmc_sdio_runtime_resume  (just before mmc_sdio_power_restore is
called), and the value passed to mmc_sdio_init_card() a little
later in mmc_sdio_power_restore().

Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:30:58 +01:00
Ondrej Zary
a5eb8bbd66 mmc: add Toshiba PCI SD controller driver
This patch resurrects an old never-finished driver for Toshiba PCI SD
controllers found in some older Toshiba laptops (such as Portege R100):

02:0d.0 System peripheral [0880]: Toshiba America Info Systems SD TypA Controller [1179:0805] (rev 05)

The code is fixed, cleaned up and successfully tested with SD, SDHC, SDXC and
MMC cards on Portege R100. (MMC cards don't even work in Windows!)
SDIO probably does not work (don't have any SDIO card).

The hardware is slow (around 2 MB/s - same in Windows) because it does not
support bus mastering (busmaster enable bit cannot be set in PCI control reg).
Also the card clock is limited to 16MHz (33MHz PCI clock divided by 2).

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:30:58 +01:00
Abhilash Kesavan
89ad2be75a mmc: dw_mmc: exynos: Add support for exynos7
The Exynos7 has a DWMMC controller (v2.70a) which is different from
prior versions. This patch adds new compatible strings for exynos7.
This patch also fixes the CLKSEL register offset on exynos7.

Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:30:57 +01:00
Johan Rudholm
2d079c43bc mmc: core: consistent handling of initial values
mmc_do_hw_reset(), mmc_power_up() and mmc_power_off() all set similar
initial values for bus_mode, bus_width, chip_select and timing. Let's
make this handling simpler and more consistent by sticking them
together in a common function. This will introduce small changes in
behavior in the following places:

mmc_power_off():

  For SPI hosts, explicitly set bus_mode = MMC_BUSMODE_PUSHPULL and
  chip_select = MMC_CS_HIGH, before we left them as they were.

  For non-SPI hosts, set bus_mode = MMC_BUSMODE_PUSHPULL instead of
  MMC_BUSMODE_OPENDRAIN as before.

  These two changes should not be a problem since the device will be
  powered off anyway.

mmc_do_hw_reset():

  Always set bus_mode = MMC_BUSMODE_PUSHPULL, as required by SD/SDIO
  cards. MMC cards require MMC_BUSMODE_OPENDRAIN, but this is taken
  care of by mmc_init_card() and mmc_attach_mmc().

Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:30:57 +01:00
Andreas Fenkart
80412ca8ab mmc: omap_hsmmc: remove unused slot_id parameter
omap_hsmmc only supports one slot. So slot id is always zero, and
slot id was never used in the callbacks anyway

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-26 14:30:56 +01:00