Since both snd_hda_codec_flush_amp_cache() and
snd_hda_codec_flush_cmd_cache() are called usually at the same time,
we can simply combine them to a single function,
snd_hda_codec_flush_cache().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture volume put callback may call the node selection change,
and its actual call won't be triggered unless flushed. In general,
we always need to call both snd_hda_codec_flush_amp_cache() and
snd_hda_codec_flush_cmd_cache() at the same place...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both the HP auto-mute and the independent HP mode conflict with each
other. Make HP auto-mute disabled (only for the affected HP jack)
during the driver is in HP independent mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It'd be better to give another name to the secondary (alt) analog PCM
stream, which is dedicated for the independent HP out and extra
inputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch eventually fixes two issues:
- Handle the case where the primary output is a headphone and can have
independent HP mode;
so far we checked only the case where the headphone is the secondary
output.
- Fix the conflict of HP independent mode and aamix mode;
when switched to aamix mode, the DAC might be also switched to
another widget shared with other outputs. Then even if we disable
the DAC for the original output, it doesn't change -- because the
active route is from another (shared) DAC to HP pin through aamix.
So, in such a case, we have to prohibit the switch to aamix for HP
routes.
This fixes issues appearing on VT codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many codecs provide routes to multiple output pins through an aamix
widget, but most of them do it only from a single DAC. However, the
current generic parser checks only the aamix paths from the original
(directly bound) DACs through aamix NID, and miss the path:
primary DAC -> aamix -> target out pin
This patch adds a more check for the routes like the above.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a patch couldn't be resolved in try_assign_dacs() although the
target DAC is expected, we forgot to add a proper badness value but
continued.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since fill_and_eval_dacs() may be called repeatedly with different
configurations, setting pinctls at each time there isn't optimal.
We can set it better only once after deciding the output configuration
in parse_output_paths().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Print the information of outputs in a bit more details and concisely
in a single place instead of printing the path at each time when
detected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch "ALSA: hda - fix wrong adc_idx in generic parser" fixed the
adc_idx for the capture volume and capture switch controls. But also
modified the adc_idx retrieval for the capture source controls
wrongly. As multiple capture source controls are created in a single
shot with counts > 1, the id.index doesn't contain the real value.
The real index has to be taken via snd_ctl_get_ioffidx() as in the
original code.
This patch reverts the fixes partially to recover from the
regression.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just stumbled over this one while reading the code.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I found a codec configuration which had six inputs, so the max of
five was not appropriate.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although I commented that boost volumes would be added only for
line-in and mic pins in the source code, the actual code excludes but
for mic-in. Fix it to accept the line-ins, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Two hooks in hda_gen_spec, cap_sync_hook and capture_switch_hook, play
very similar roles. The only differences are that the former is
called more often (e.g. at init or switching capsrc) while the latter
can take an on/off argument.
As a more generic implementation, consolidate these two hooks, and
pass snd_ctl_elem_value pointer as the second argument. If the
secondary argument is non-NULL, it can take the on/off value, so the
caller handles it like the former capture_switch_hook. If it's NULL,
it's called in the init or capsrc switch case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a standard capture switch without multiple binding is used, the
call for capture_switch_hook isn't called properly. Replace the put
ops to add the hook call in that case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current generic parser code, we look for the (mic) boost
controls only on input pins. But many codecs assign the boost volume
to a widget connected to each input pin instead of the input amp of
the pin itself.
In this patch, the parser tries to look through more widgets connected
to the pin and find a boost amp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When an amp in the activation path is associated with mixer controls,
activate_amp() tries to skip the initialization. It's good, but only
if the mixer really initializes both mute and volume. Otherwise,
either the mute of the volume is left uninitialized.
This patch adds this missing check and properly initialize the
partially controlled amps in an activation path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are a few places creating the labels and indices of kctls for
each input pin in the current generic parser code. This is redundant
and makes harder to maintain. Let's create the labels and indices at
once and keep them in hda_gen_spec.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the imux table entries can be a subset of autocfg.input table,
the indices of these aren't always same. For passing the proper index
value of autocfg.input at creating input ctl labels (via
snd_hda_autocfg_input_label()), keep the corresponding autocfg.input
idx value in the index field of each imux item, which isn't used in
the generic driver.
Also, this makes easier to check the invalid imux pin for stereo mix.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the volume or mute control of the primary output is shared with
other (headphone or speaker) outputs, we shouldn't name it as a
specific output type but rather name it with the channel name or a
generic name like "PCM".
Also, this check should be performed individually for the volume and
the mute controls because some codecs may have shared volumes but
separate mute controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the generic parser reduces the ADC list, copy the list of the
all detected ADCs and keep it.
This list can be later referred by the codec driver for finer power
controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add vmaster_tlv[] to hda_gen_spec and store the suggested TLV data
in snd_hda_gen_parse_auto_config(). This allows the codec driver to
correct the TLV data (e.g. mute capability) before actually creating
vmaster instance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just like the jack mode enum ctls for output jacks, add the support
for similar enum ctls for input pins to control the bias Vref.
The new controls will be added when spec->add_in_jack_modes is set
either by the codec driver or by a hint string.
Note that ground and 100% vrefs are excluded from the list for
simplicity, currently. We may add a new flag to allow them, too.
But I guess it's easier to put a value override in the pinfix in such
a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A new flag to skip the auto-mute handling in the generic parser, just
like suppress_auto_mic flag. It has to be set before calling
snd_hda_gen_parse_auto_config().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise no PCM will be built for codecs without analog I/O.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Otherwise setting the capture volume for amps will be weird and
inconsistent (it will try to set values outside the range of the
second amp based on capabilities of the first amp).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the input node does not have any volume capable input amp,
don't add such a control.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Even a single DAC can output two channels, so the channel count
is twice the number of DACs.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We use knew->index for adc_idx when we create "Capture Volume" and
"Capture Switch", so use the same to retrieve adc_idx.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag to indicate whether HP amp is turned on as default for
speaker or line-outs, and enable this for ALC260 codec, as many
machines with this codec require the HP amp even for speakers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the enum controls for changing the headphone amp bits of output
jacks, such as "Headphone Jack Mode". This feature isn't enabled as
default, so far, unless spec->add_out_jack_modes flag is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a multi-io jack is switched to another direction, call the
automute and autoswitch update functions, as this jack won't be used
as the headphone or the mic jack that may turn off others.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a jack is retasked as a different direction (e.g. a mic jack is
used as a CLFE output), such a jack shouldn't be counted as the target
for the automatic jack switching. Skip the automute or the autoswitch
when the current pinctl direction is different from what we suppose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the new pin target accessors for managing the current pinctl
values in the generic parser. The pinctl values of all active pins
are once determined at the initialization phase, and stored via
snd_hda_codec_set_pin_target(). This will be referred again in the
codec init or resume phase to set the actual pinctl.
This value is kept while the auto-mute. When a line-out or a speaker
pin is muted by auto-mute, the driver simply disables the pin, but it
doesn't touch the cached pinctl target value. Upon unmute, this value
is used to restore the original pinctl in return.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a DAC is reassigned from surrounds to front or ADCs are reduced
due to incomplete imux, we clear the path indices but the path
instances remain as is. Since the paths might be still referred
through the whole path list parsing (e.g. is_active_nid()), we should
clear these path instances as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since some codecs can choose the aamix as a capture source, we should
support it as well. When spec->add_stereo_mix_input flag is set, the
parser checks the availability of aamix as the input source, and adds
the paths automatically when possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current parser code, the input_paths[] may become inconsistent
when some of detected ADCs are dropped due to incomplete inputs, since
the driver rearranges only adc_nids[] but doesn't touch input_paths[].
This patch fixes the issue, and also it optimizes the reachability
checks by simply referring to the parsed input_paths[] instead of
calling is_reachable() again for each connection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of handling special cases in the caller side, give a proper
name string "Headphone Mic" from hda_get_autocfg_input_label() when
the headhpone jack pin is specified as an input.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture paths shouldn't contain the analog loopback mixer.
Pass a proper argument to exclude the aamix NID.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag spec->suppress_mic_auto_switch for codecs that don't
support unsol events properly like VT1708.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit modifies the definition of snd_hda_parse_nid_path()
slightly, now with_aa_mix argument is changed to anchor_nid, so that
it can handle any NID generically as an anchor point to include or
exclude.
The with_aa_mix field in struct nid_path is removed again by this
change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The multi-io channels can vary not only from 1 to 6 but also may vary
from 6 to 8 or such. At the same time, there are more speaker pins
available than the primary output pins. So, we need three variables
to check: the minimum channel counts for primary outputs, the current
channel counts for primary outputs, and the minimum channel counts for
all outputs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
