There are two checks to see if the manual gpio is configured, but
these the check is seeing if the structure is NULL instead it
should check to see if there are CTS and/or RTS pins defined.
This patch uses checks for those individual pins instead of
checking for the structure itself to restore auto RTS/CTS.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Yegor Yefremov <yegorslists@googlemail.com>
Link: https://lore.kernel.org/r/20191006163314.23191-2-aford173@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For many years omap variants have been setting the runtime PM
autosuspend delay to -1 to prevent unsafe policy with lossy first
character on wake-up. The user must specifically enable the timeout
for UARTs if desired.
We must not enable the workaround for serdev devices though. It leads
into UARTs not idling if no serdev devices are loaded and there is no
sysfs entry to configure the UART in that case. And this means that
my PM may not work unless the serdev modules are loaded.
We can detect a serdev device being configured based on a dts child
node, and we can simply skip the workround in that case. And the
serdev driver can idle the port during runtime when suitable if an
out-of-band wake-up GPIO line exists for example.
Let's also add some comments to the workaround while at it.
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20190723115400.46432-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Changed by Stefan:
Only call mctrl_gpio_init(), if the device has no ACPI companion device
to not break existing ACPI based systems. Also only use the mctrl_gpio_
functions when "gpios" is available.
Use MSR / MCR <-> TIOCM wrapper functions.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor out similar code pieces that set or clear UART_IER_THRI bit to
serial8250_{set,clear}_THRI() helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_omap driver uses clock-frequency DT property to obtain functional
clk frequency. This is not ideal as users need to calculate functional
clk frequency offline and populate it in DT.
Therefore add support to obtain functional clock frequency using clk
APIs when clock-frequency DT property is not defined.
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250_omap is DT only driver so dev->of_node always exists. Drop check
for existence of valid dev->of_node to simplify omap8250_probe().
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's take advantage of the new ("serial: core: Allow processing sysrq
at port unlock time") to handle sysrqs more cleanly.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM654 uses a UART controller that is compatible (partially) with
existing 8250 UART, however, has a few differences with respect to DMA
support and control paths. Introduce a base definition that allows us
to build up the differences in follow on patches.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed that unused UARTs won't necessarily idle properly always
unless at least one byte tx transfer is done first.
After some debugging I narrowed down the problem to the scr register
dma configuration bits that need to be set before softreset for the
clocks to idle. Unless we do this, the module clkctrl idlest bits
may be set to 1 instead of 3 meaning the clock will never idle and
is blocking deeper idle states for the whole domain.
This might be related to the configuration done by the bootloader
or kexec booting where certain configurations cause the 8250 or
the clkctrl clock to jam in a way where setting of the scr bits
and reset is needed to clear it. I've tried diffing the 8250
registers for the various modes, but did not see anything specific.
So far I've only seen this on omap4 but I'm suspecting this might
also happen on the other clkctrl using SoCs considering they
already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE.
Let's fix the issue by configuring scr before reset for basic dma
even if we don't use it. The scr register will be reset when we do
softreset few lines after, and we restore scr on resume. We should
do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag
set since the ones with UART_ERRATA_CLOCK_DISABLE are all based
using clkctrl similar to omap4.
Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL
bits are needed for the clkctrl to idle after a softreset.
And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE
for the related workaround to be enabled. This same compatible
value will also be used for omap5.
Fixes: cdb929e445 ("serial: 8250_omap: workaround errata around idling UART after using DMA")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable/Clear module level UART wakeup in UART_OMAP_WER register based on
return value of device_may_wakeup() in .suspend(). This allows
userspace to use sysfs to control the ability of UART to wakeup the
system from deep sleep state. Register is restored back in .startup()
call that happens as part of resume sequence.
With this patch, userspace can control UART wakeup capability via sysfs:
To enable wakeup capability:
echo enabled > /sys/class/tty/ttyXX/device/power/wakeup
For disabling wakeup capability:
echo disabled > /sys/class/tty/ttyXX/device/power/wakeup
Note that the UART wakeup events configured in the 8250 hardware only
work for idle modes that do not cut off power for the UART. For deeper
idle states, dedicated padconf wakeirqs must be used. Or in some cases
the UART RX pin can be remuxed to GPIO input if the GPIO block stays
powered.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_8250_throttle() is called when tty RX buffer is about to overflow
and can no longer keep up with the rate at which UART is receiving data.
So, the expectation of this callback, is that UART stops RX and asserts
HW flow control to signal the sender to stop sending more data.
omap_8250_throttle() disables RX FIFO interrupts thus FIFO is no longer
serviced, leading to assertion of flow control once RX FIFO is full.
But, this does not work when DMA is enabled as driver keeps queuing new
RX DMA request in completion handler without brothering about throttling
request made by the higher layer.
This patch introduces a flag that can be used to determine whether or
not to queue next RX DMA request based on throttling request.
Without this patch, tty buffer overflows are reported at higher
baudrates.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed a spelling error in a comment.
Signed-off-by: Rolf Evers-Fischer <rolf.evers.fischer@aptiv.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/tty files files with the correct SPDX license
identifier based on the license text in the file itself. The SPDX
identifier is a legally binding shorthand, which can be used instead of
the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Joachim Eastwood <manabian@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: "Uwe Kleine-König" <kernel@pengutronix.de>
Cc: Pat Gefre <pfg@sgi.com>
Cc: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Barry Song <baohua@kernel.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@tabi.org>
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Jiri Slaby <jslaby@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a define for the maximum baud rate divisor, to improve code
readability.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA RX completion handler for UART is called from a tasklet and hence
may be delayed depending on the system load. In meanwhile, there may be
RX timeout interrupt which can get serviced first before DMA RX
completion handler is executed for the completed transfer.
omap_8250_rx_dma_flush() which is called on RX timeout interrupt makes
sure that the DMA RX buffer is pushed and then the FIFO is drained and
also queues a new DMA request. But, when DMA RX completion handler
executes, it will erroneously flush the currently queued DMA transfer
which sometimes results in data corruption and double queueing of DMA RX
requests.
Fix this by checking whether RX completion is for the currently queued
transfer or not. And also hold port lock when in DMA completion to avoid
race wrt RX timeout handler preempting it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel always writes log messages to console via
serial8250_console_write()->serial8250_console_putchar() which directly
accesses UART_TX register _without_ using DMA.
But, if other processes like systemd using same UART port, then these
writes are handled by a different code flow using 8250_omap driver where
there is provision to use DMA.
It seems that it is possible that both DMA and CPU might simultaneously
put data to UART FIFO and lead to potential loss of data due to FIFO
overflow and weird data corruption. This happens when both kernel
console and userspace tries to write simultaneously to the same UART
port. Therefore, disable DMA on kernel console port to avoid potential
race between CPU and DMA.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise the interconnect related code implementing PM runtime will
produce these errors on a failed probe:
omap_uart 48066000.serial: omap_device: omap_device_enable() called from invalid state 1
omap_uart 48066000.serial: use pm_runtime_put_sync_suspend() in driver?
Note that we now also need to check for priv in omap8250_runtime_suspend()
as it has not yet been registered if probe fails. And we need to use
pm_runtime_put_sync() to properly idle the device like we already do
in omap8250_remove().
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 UART DMA support was marked broken by default as it was not
possible to pause ongoing RX DMA transfer. Now that both SDMA and
EDMA can support pause operation for RX DMA transactions, don't set
rx_dma_broken to true by default. With this patch 8250_omap driver will
use DMA by default.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART uses as EDMA as dma engine on AM437x SoC and therefore, requires
OMAP_DMA_TX_KICK quirk just like AM33xx. So, enable OMAP_DMA_TX_KICK
quirk for AM437x platform as well. While at that, drop use of
of_machine_is_compatible() and instead pass quirks via device data.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that DMA transfer is already complete but, completion
handler is yet to be called, when dmaengine_pause() is called in case of
error condition(like break/rx timeout). This leads to dmaengine_pause()
API to return EINVAL (as descriptor is already NULL) causing
rx_dma_broken flag to be set and effectively disabling RX DMA.
Fix this by calling dmaengine_pause() only when transfer is in progress.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serial console is broken in v4.8-rcX. Mika and I independently bisected down to
commit 4ef03d3287 ("tty/serial/8250: use mctrl_gpio helpers").
Since neither author nor anyone else didn't propose a solution we better revert
it for now.
This reverts commit 4ef03d3287.
Link: https://lkml.kernel.org/r/20160809130229.GN1729@lahna.fi.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce serial8250_out_MCR() and serial8250_in_MCR() routines, that
replace following calls:
serial_out(port, UART_MCR, val)
serial_port_out(up, UART_MCR, val)
serial_in(port, UART_MCR)
This patch is needed in order to integrate reading/writing of MCR
signals via SERIAL_MCTRL_GPIO infrastructure later.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA completed normally does not require termination; only terminate
paused rx dma stemming from rx dma flush.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using fake IIR values to perform rx dma operations unnecessarily
conflates separate operations, stopping in-progress dma with starting
new dma.
Introduce serial8250_rx_dma_flush() to handle stopping in-progress dma
[omap8250 already has equivalent omap_8250_rx_dma_flush()].
Replace rx_dma(UART_IIR_RX_TIMEOUT) with the equivalent *_rx_dma_flush(),
and rx_dma(0) with the equivalent *_rx_dma(). Handle IIR steering
in the irq handler with handle_rx_dma() helper.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the operation (restarting new rx dma) performed when error
argument is true.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 27c310c5c3 ("serial: 8250_dma: no need to sync RX buffer")
notes the RX DMA buffer is allocated from DMA coherent memory, and
thus does not need sync'd for each transaction. The same is true
for OMAP RX DMA.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_err is not used other than for boolean evaluation;
substitute the actual operation directly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
up_to_u8250p() casts struct uart_port * to struct uart_8250_port *. Update code
to use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use software emulated RS485 direction control to provide RS485 API
existed in omap_serial driver. Note that 8250_omap issues interrupt
on shift register empty which is single prerequesite for using software
emulated RS485.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clearing UART_MCR_RTS or UART_MCR_XONANY is unnecessary; these bits
are never set in the shadow mcr. The RTS clear is especially confusing.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_insert_flip_string() returns an int and as such it
might fail. So the result is that I kindly asked to insert 48 bytes and
the function only insterted 32.
I have no idea what to do with the remaining 16 so I think dropping them
is the only option. I also increase the buf_overrun counter so userpace
has a clue that we lost bytes.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250-omap driver requires the DMA-engine driver to support the pause
command in order to properly turn off programmed RX transfer before the
driver stars manually reading from the FIFO.
The lacking support of the requirement has been discovered recently. In
order to stay safe here we disable RX-DMA completly on probe.
The rx_dma_broken assignment on probe could be removed once we working
pause function in omap-dma.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP h/w-assisted IXON flow control is borked. The transmitter becomes
stuck if XON is never received; clearing the fifos or resetting the
rx flow control bits has no effect.
Remove auto-IXANY as well, since without auto-IXON, it has no purpose.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to Advisory 21 as documented in AM437x errata document,
UART module cannot be disabled once DMA is used. The only
workaround is to softreset the module before disabling it.
DRA7x UARTs are compatible to AM437x UARTs in terms of
this errata and prescribed workaround.
Enable usage of workaround for this errata on DRA7x SoCs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM335x, AM437x and DRA7x SoCs have an errata[1] due to which UART
cannot be idled after it has been used with DMA.
OMAP3 has a similar sounding errata which has been worked around
in a2fc36613a ("ARM: OMAP3: Use manual idle for UARTs
because of DMA errata"). But the workaround used there does not
apply to AM335x, AM437x SoCs.
After using DMA, the UART module on these SoCs must be soft reset
to go to idle.
This patch implements that errata workaround. It is expected that
UART will be used with DMA so no explicit check for DMA usage
has been added for errata applicability.
MDR1 register needs to be restored right after soft-reset because
"UART mode" must be set in that register for module wake-up on AM335x
to work. As a result, SCR register is now used to determine if
context was lost during sleep.
[1] See Advisory 21 in AM437x errata SPRZ408B, updated April 2015.
http://www.ti.com/lit/er/sprz408b/sprz408b.pdf
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of of_machine_is_compatible() for handling AM335x specific
"DMA kick" quirk in 8250_omap driver makes it ugly to extend the
quirk for other platforms. Instead use a new compatible.
The new compatible will also make it easier to take care of
other quirks on AM335x and like SoCs.
In order to not break backward DTB compatibility for users of
8250_omap driver on AM335x based boards, existing use of
of_machine_is_compatible() has not been removed.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The silicon errata[1] workaround implemented in a follow-on
patch, "serial: 8250_omap: workaround errata on disabling
UART after using DMA", requires MDR1 register programming.
Extract MDR1 register update into helper function,
omap8250_update_mdr1() to help with that.
[1] Advisory 21 in http://www.ti.com/lit/er/sprz408b/sprz408b.pdf
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
omap_device infrastructure has a suspend_noirq hook which
runtime suspends all devices late in the suspend cycle (see
_od_suspend_noirq() in arch/arm/mach-omap2/omap_device.c)
This leads to a NULL pointer exception in 8250_omap driver
since by the time omap8250_runtime_suspend() is called, 8250_dma
driver has already set rxchan to NULL via serial8250_release_dma().
Make an explicit check to see if rxchan is NULL in
runtime_{suspend|resume} hooks to fix this.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can now use generic wakeirq handling and remove the custom handling
for the wake-up interrupts.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d118 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").
This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.
Fixes: ca8bb4aefb ("serial: 8250: Revert "tty: serial: 8250_core:
read only RX if there is something in the FIFO"")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rx_running flag should show if DMA is currently active. However
there is a window between when the flag is set/cleared and when
the DMA is started/stopped. Because the flag is queried from both
hard and soft irq contexts, the driver can make incorrect
decisions and do things like start a DMA transfer using a buffer
that is already setup to be used for a DMA transfer.
This patch adds a spinlock to synchronize the rx_running flag and
close the above mentioned window.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial_core.h file have been included in header file
serial_8250.h. so remove the "#include <serial_core.h>" in
some 8250 serial drivers, because they have included the header file
serial_8250.h.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 88838d3112702 ("serial: omap_8250: Fix RTS handling") fixed
RTS pin control when in autoRTS mode.
New support added in "serial: core: Rework hw-assisted flow control support"
enables a much simpler approach; rather than masking out autoRTS
whenever writing the EFR register, use the UPSTAT_* mode to determine if
autoRTS should be enabled when raising RTS (in omap8250_set_mctrl()).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hw-assisted flow control support was added to the serial core
in v3.8 with commits,
dba05832cb ("SERIAL: core: add hardware assisted h/w flow control support")
2cbacafd7a ("SERIAL: core: add hardware assisted s/w flow control support")
9aba8d5b01 ("SERIAL: core: add throttle/unthrottle callbacks for hardware
assisted flow control")
Since then, additional requirements for serial core support have arisen.
Specifically,
1. Separate tx and rx flow control settings for UARTs which only support
tx flow control (ie., autoCTS).
2. Disable sw-assisted CTS flow control in autoCTS mode
3. Support for RTS flow control by serial core and userspace in autoRTS mode
Distinguish mode from capability; introduce UPSTAT_AUTORTS, UPSTAT_AUTOCTS
and UPSTAT_AUTOXOFF which, when set by the uart driver, enable serial core
support for hw-assisted rx, hw-assisted tx and hw-assisted in-band/IXOFF
rx flow control, respectively. [Note: hw-assisted in-band/IXON tx flow
control does not require serial core support/intervention and can be
enabled by the uart driver when required.]
These modes must be set/reset in the driver's set_termios() method, based
on termios settings, and thus can be safely queried in any context in which
one of the port lock, port mutex or termios rwsem are held. Set these modes
in the 2 in-tree drivers, omap-serial and 8250_omap, which currently
use UPF_HARD_FLOW/UPF_SOFT_FLOW support.
Retain UPF_HARD_FLOW and UPF_SOFT_FLOW as capabilities; re-define
UPF_HARD_FLOW as both UPF_AUTO_RTS and UPF_AUTO_CTS to allow for distinct
and separate rx and tx flow control capabilities.
Disable sw-assisted CTS flow control when UPSTAT_AUTOCTS is enabled.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the OMAP3 UART ignores MCR[1] (RTS) in autoRTS mode, autoRTS
mode must not be enabled unless RTS is set (or port->mctrl & TIOCM_RTS,
which is equivalent).
Fixes premature raising of RTS in omap_8250_set_termios() -- RTS was
raised even before UART mode was selected.
Fixes raise of RTS after port has been shutdown; omap_8250_pm() re-enabled
RTS after omap_8250_shutdown().
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OMAP3 UART ignores MCR[1] (ie., UART_MCR_RTS) when in autoRTS
mode (UPF_HARD_FLOW + CRTSCTS). This makes it impossible for either
the serial core or userspace to manually flow control the sender.
Disable autoRTS mode when RTS is lowered and restore the previous
mode when RTS is raised.
Note that the OMAP3 UART provides no mechanism for switching from
autoRTS mode without corrupting incoming data; to access the
necessary register, the line control settings must be set to 8-e-2
and thus any data received during that time will be interpreted with
those settings. This corruption has been observed in practice.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch invokes add_preferred_console() with ttyS based on ttyO
arguments if the user didn't specify it on its own. This ensures that
the user will see the kernel booting on his serial console in case he
forgot to update the command line.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
