As of commit b9ddd50911 ("iio: adc: max9611: Fix temperature
reading in probe"), max9611 initialization sometimes fails on the
Salvator-X(S) development board with:
max9611 4-007f: Invalid value received from ADC 0x8000: aborting
max9611: probe of 4-007f failed with error -5
The max9611 driver tests communications with the chip by reading the die
temperature during the probe function, which returns an invalid value.
According to the datasheet, the typical ADC conversion time is 2 ms, but
no minimum or maximum values are provided. Maxim Technical Support
confirmed this was tested with temperature Ta=25 degreeC, and promised
to inform me if a maximum/minimum value is available (they didn't get
back to me, so I assume it is not).
However, the driver assumes a 1 ms conversion time. Usually the
usleep_range() call returns after more than 1.8 ms, hence it succeeds.
When it returns earlier, the data register may be read too early, and
the previous measurement value will be returned. After boot, this is
the temperature POR (power-on reset) value, causing the failure above.
Fix this by increasing the delay from 1000-2000 µs to 3000-3300 µs.
Note that this issue has always been present, but it was exposed by the
aformentioned commit.
Fixes: 69780a3bbc ("iio: adc: Add Maxim max9611 ADC driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Each time we need to read a sample (from the sysfs interface, since the
driver supports only it) the driver writes the configuration register
with the proper settings needed to perform the said read, then it runs
another xfer to actually read the resulting value. Most notably the
configuration register is updated to set the ADC internal MUX depending by
which channel the read targets.
Unfortunately this seems not enough to ensure correct operation because
the ADC works in a pipelined-like fashion and the new configuration isn't
applied in time.
The ADC alternates two phases: acquisition and conversion. During the
acquisition phase the ADC samples the analog signal in an internal
capacitor; in the conversion phase the ADC performs the actual analog to
digital conversion of the stored voltage. Note that of course the MUX
needs to be set to the proper channel when the acquisition phase is
performed.
Once the conversion phase has been completed, the device automatically
switches back to a new acquisition; on the other hand the device switches
from acquisition to conversion on the rising edge of SPI cs signal (that
is when the xfer finishes).
Only after both two phases have been completed (with the proper settings
already written in the configuration register since the beginning) it is
possible to read the outcome from SPI bus.
With the current driver implementation, we end up in the following
situation:
_______ 1st xfer ____________ 2nd xfer ___________________
SPI cs.. \_________/ \_________/
SPI rd.. idle |(val N-2)+ idle | val N-1 + idle ...
SPI wr.. idle | cfg N + idle | (X) + idle ...
------------------------ + -------------------- + ------------------
AD .. acq N-1 + cnv N-1 | acq N + cnv N | acq N+1
As shown in the diagram above, the value we read in the Nth read belongs
to configuration setting N-1.
In case the configuration is not changed (config[N] == config[N-1]), then
we still get correct data, but in case the configuration changes (i.e.
switching the MUX on another channel), we get wrong data (data from the
previously selected channel).
This patch fixes this by performing one more "dummy" transfer in order to
ending up in reading the data when it's really ready, as per the following
timing diagram.
_______ 1st xfer ____________ 2nd xfer ___________ 3rd xfer ___
SPI cs.. \_________/ \_________/ \_________/
SPI rd.. idle |(val N-2)+ idle |(val N-1)+ idle | val N + ..
SPI wr.. idle | cfg N + idle | (X) + idle | (X) + ..
------------------------ + -------------------- + ------------------- + --
AD .. acq N-1 + cnv N-1 | acq N + cnv N | acq N+1 | ..
NOTE: in the latter case (cfg changes), the acquisition phase for the
value to be read begins after the 1st xfer, that is after the read request
has been issued on sysfs. On the other hand, if the cfg doesn't change,
then we can refer to the fist diagram assuming N == (N - 1); the
acquisition phase _begins_ before the 1st xfer (potentially a lot of time
before the read has been issued via sysfs, but it _ends_ after the 1st
xfer, that is _after_ the read has started. This should guarantee a
reasonably fresh data, which value represents the voltage that the sampled
signal has after the read start or maybe just around it.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver forgets to unregister the iio trigger in probe failure and
remove.
Use devm API to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This probe function is passing the wrong size to devm_iio_device_alloc().
It is supposed to be the size of the private data. Fortunately,
sizeof(*indio_dev) is larger than sizeof(struct mrfld_adc) so it doesn't
cause a runtime problem.
Fixes: a711866273 ("iio: adc: intel_mrfld_adc: Add Basin Cove ADC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When the internal reference was selected by a channel it was not enabled.
This patch fixes that and enables it.
Fixes: b3af341bbd ("iio: adc: Add ad7124 support")
Signed-off-by: Mircea Caprioru <mircea.caprioru@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When a conversion result is being read from ADC, the driver reads the
number of channels + 1 because it thinks that IIO_CHAN_SOFT_TIMESTAMP
is also a physical channel. This patch fixes this issue.
Fixes: 2985a5d884 ("staging: iio: adc: ad7606: Move out of staging")
Reported-by: Robert Wörle <rwoerle@mibtec.de>
Signed-off-by: Beniamin Bia <beniamin.bia@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
New device support
* ad5446
- Support the ad5600 DAC (id only needed).
* ad7292 ADC DAC etc
- New driver plus dt-bindings.
* veml6030 ambient light sensor
- New driver plus dt-bindings and sysfs docs.
Features
* mpu6050
- Explicit VDD control.
* stm32-adc
- Allow limiting of max clock frequency from devicetree to ensure it's
suitable for external circuitry.
yaml binding conversions
* ltc1660
* mcp3911
Fixes
* adis16480
- Fix wrong scale factors.
- Fix debugfs reg access by providing the callback.
* cros_ec_baro
- Fixing missing mask entry to make available sample frequencies visible
in sysfs.
* st_lsm6dsx
- Explicitly handle different ODR table sizes.
- Handle restrictions between slave ODR and accel ODR when
both are enabled.
- Allow ODR to be expressed more accurately by using miliHz.
* tools
- Fix an issue with parallel builds.
Cleanups and warning fixes
* adis16136, adis16400, adis16460, adis-lib
- Change some checks on return values to be for 0 rather than strictly
negative. Avoids some fiddly issues with the compiler concluding some
variables are initialized due to a mixture of error checks.
- Assign values only on success of 'read' operations - avoiding any
chance the compiler will falsly suggest they might be used uninitialized.
- Whitespace and simlar cleanups.
* aspeed adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* bcm-iproc-adc
- Stray semicolon removal.
* cc10001
- devm_platfom_ioremap_resource to reduce boilerplate.
* dln2-adc
- Reorganise the buffered mode setup and tear down. Part of moving towards
being able to refactor this area of the IIO core.
* hdc100x
- Reorganise the buffered mode setup and tear down.
* ingenic-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
* mt6577
- devm_platfom_ioremap_resource to reduce boilerplate.
* npcm
- devm_platfom_ioremap_resource to reduce boilerplate.
* rcar-gyroadc
- devm_platfom_ioremap_resource to reduce boilerplate.
* spear-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
-----BEGIN PGP SIGNATURE-----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=ckQz
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.5c' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of IIO new device support cleanups and fixes for the 5.5 cycle.
New device support
* ad5446
- Support the ad5600 DAC (id only needed).
* ad7292 ADC DAC etc
- New driver plus dt-bindings.
* veml6030 ambient light sensor
- New driver plus dt-bindings and sysfs docs.
Features
* mpu6050
- Explicit VDD control.
* stm32-adc
- Allow limiting of max clock frequency from devicetree to ensure it's
suitable for external circuitry.
yaml binding conversions
* ltc1660
* mcp3911
Fixes
* adis16480
- Fix wrong scale factors.
- Fix debugfs reg access by providing the callback.
* cros_ec_baro
- Fixing missing mask entry to make available sample frequencies visible
in sysfs.
* st_lsm6dsx
- Explicitly handle different ODR table sizes.
- Handle restrictions between slave ODR and accel ODR when
both are enabled.
- Allow ODR to be expressed more accurately by using miliHz.
* tools
- Fix an issue with parallel builds.
Cleanups and warning fixes
* adis16136, adis16400, adis16460, adis-lib
- Change some checks on return values to be for 0 rather than strictly
negative. Avoids some fiddly issues with the compiler concluding some
variables are initialized due to a mixture of error checks.
- Assign values only on success of 'read' operations - avoiding any
chance the compiler will falsly suggest they might be used uninitialized.
- Whitespace and simlar cleanups.
* aspeed adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* bcm-iproc-adc
- Stray semicolon removal.
* cc10001
- devm_platfom_ioremap_resource to reduce boilerplate.
* dln2-adc
- Reorganise the buffered mode setup and tear down. Part of moving towards
being able to refactor this area of the IIO core.
* hdc100x
- Reorganise the buffered mode setup and tear down.
* ingenic-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* lpc18xx-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
* mt6577
- devm_platfom_ioremap_resource to reduce boilerplate.
* npcm
- devm_platfom_ioremap_resource to reduce boilerplate.
* rcar-gyroadc
- devm_platfom_ioremap_resource to reduce boilerplate.
* spear-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-adc
- devm_platfom_ioremap_resource to reduce boilerplate.
* vf610-dac
- devm_platfom_ioremap_resource to reduce boilerplate.
* tag 'iio-for-5.5c' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (43 commits)
iio: adis16480: Add debugfs_reg_access entry
iio: adis16480: Fix scales factors
tools: iio: Correctly add make dependency for iio_utils
iio: adc: Add driver support for AD7292
dt-bindings: iio: adc: Add dt-schema for AD7292
dt-bindings: iio: adc: Migrate MCP3911 documentation to yaml
iio: imu: mpu6050: Add support for vdd-supply regulator
dt-bindings: iio: imu: mpu6050: add vdd-supply
iio: cros_ec_baro: set info_mask_shared_by_all_available field
iio: dac: ad5446: Add support for new AD5600 DAC
dt-bindings: iio: dac: Migrate LTC1660 documentation to yaml
iio: documentation: light: Add veml6030 sysfs documentation
dt-bindings: iio: light: add veml6030 ALS bindings
iio: light: add driver for veml6030 ambient light sensor
iio: imu: st_lsm6dsx: express odr in mHZ
iio: imu: st_lsm6dsx: fix ODR check in st_lsm6dsx_write_raw
iio: imu: st_lsm6dsx: explicitly define odr table size
iio: adc: stm32: allow to tune analog clock
dt-bindings: iio: stm32-adc: add max clock rate property
iio: dac: vf610: Use devm_platform_ioremap_resource
...
The AD7292 is a 10-bit monitor and control system with ADC, DACs,
temperature sensor, and GPIOs.
Configure AD7292 devices in direct access mode, enabling single-ended
ADC readings.
Datasheet:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/ad7292.pdf
Signed-off-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new optional dt property to tune analog clock prescaler.
Driver looks for optional "st,max-clk-rate-hz", then computes
best approximation below that rate, using ADC internal prescaler.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduces boilerplate.
Suggested by coccinelle
CHECK drivers/iio/adc/vf610_adc.c
drivers/iio/adc/vf610_adc.c:819:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Fugang Duan <b38611@freescale.com>
Avoids local boilerplate doing the same thing.
Suggested by coccinelle
CHECK drivers/iio/adc/spear_adc.c
drivers/iio/adc/spear_adc.c:283:1-22: WARNING: Use devm_platform_ioremap_resource for st -> adc_base_spear6xx
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Avoids some local boilerplate.
Suggested by coccinelle.
CHECK drivers/iio/adc/rcar-gyroadc.c
drivers/iio/adc/rcar-gyroadc.c:495:1-11: WARNING: Use devm_platform_ioremap_resource for priv -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Reduces local boilerplate code.
Suggested by coccinelle via coccicheck.
CHECK drivers/iio/adc/npcm_adc.c
drivers/iio/adc/npcm_adc.c:200:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Tomer Maimon <tmaimon77@gmail.com>
Avoid local boilerplate.
Identified by coccinelle
CHECK drivers/iio/adc/lpc18xx_adc.c
drivers/iio/adc/lpc18xx_adc.c:137:1-10: WARNING: Use devm_platform_ioremap_resource for adc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Joachim Eastwood <manabian@gmail.com>
Replaces local boilerplate. Identified by coccinelle.
CHECK drivers/iio/adc/ingenic-adc.c
drivers/iio/adc/ingenic-adc.c:449:1-10: WARNING: Use devm_platform_ioremap_resource for adc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Artur Rojek <contact@artur-rojek.eu>
Reduces local boilerplate.
Found by coccinelle:
drivers/iio/adc/cc10001_adc.c:344:1-18: WARNING: Use devm_platform_ioremap_resource for adc_dev -> reg_base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Naidu Tellapati <naidu.tellapati@imgtec.com>
Reduces boilerplate. Identified by coccinelle
CHECK drivers/iio/adc/mt6577_auxadc.c
drivers/iio/adc/mt6577_auxadc.c:257:1-18: WARNING: Use devm_platform_ioremap_resource for adc_dev -> reg_base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Zhiyong Tao <zhiyong.tao@mediatek.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reduces boilerplate.
Identified by: Coccinelle / coccicheck
CHECK drivers/iio/adc/aspeed_adc.c
drivers/iio/adc/aspeed_adc.c:189:1-11: WARNING: Use devm_platform_ioremap_resource for data -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Rick Altherr <raltherr@google.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
The iio_triggered_buffer_postenable() hook should be called first to
attach the poll function. The iio_triggered_buffer_predisable() hook is
called last (as is it should).
This change moves iio_triggered_buffer_postenable() to be called first. It
adds iio_triggered_buffer_predisable() on the error paths of the postenable
hook.
For the predisable hook, some code-paths have been changed to make sure
that the iio_triggered_buffer_predisable() hook gets called in case there
is an error before it.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There maybe a race when using dmaengine_terminate_all(). The predisable
routine may call iio_triggered_buffer_predisable() prior to a pending DMA
callback.
Adopt dmaengine_terminate_sync() to ensure there's no pending DMA request
before calling iio_triggered_buffer_predisable().
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Set gain in hx711_reset() to its default value after a reset cycle. This
omits one precautionary read cycle, because the read is performed in
hx711_set_gain_for_channel() anyway if gain has changed.
Check for DOUT low and if its high wait some time if it goes down
instead of doing a blind reset cycle when DOUT is not down.
This is a performance optimization which allows to query the sensor with
a higher frequency.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix the following warnings when documentation is built:
drivers/iio/adc/stm32-adc-core.c:62: warning: cannot understand function
prototype: 'struct stm32_adc_common_regs '
drivers/iio/adc/stm32-adc-core.c:78: warning: cannot understand function
prototype: 'struct stm32_adc_priv_cfg '
drivers/iio/adc/stm32-adc-core.c:123: warning: Function parameter or
member 'pdev' not described in 'stm32f4_adc_clk_sel'
drivers/iio/adc/stm32-adc.c:219: warning: cannot understand function
prototype: 'struct stm32_adc_regs '
drivers/iio/adc/stm32-adc.c:237: warning: cannot understand function
prototype: 'struct stm32_adc_regspec '
drivers/iio/adc/stm32-adc.c:264: warning: cannot understand function
prototype: 'struct stm32_adc_cfg '
drivers/iio/adc/stm32-adc.c:323: warning: Function parameter or member
'difsel' not described in 'N'
drivers/iio/adc/stm32-adc.c:323: warning: Function parameter or member
'pcsel' not described in 'stm32_adc'
drivers/iio/adc/stm32-adc.c:371: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32f4_sq[STM32_ADC_MAX_SQ + 1]
drivers/iio/adc/stm32-adc.c:417: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32f4_smp_bits[] = '
drivers/iio/adc/stm32-adc.c:508: warning: cannot understand function
prototype: 'const struct stm32_adc_regs stm32h7_smp_bits[] = '
drivers/iio/adc/stm32-adc.c:1112: warning: Function parameter or member
'indio_dev' not described in 'stm32_adc_get_trig_extsel'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'indio_dev' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'reg' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'writeval' not described in 'stm32_adc_debugfs_reg_access'
drivers/iio/adc/stm32-adc.c:1420: warning: Function parameter or member
'readval' not described in 'stm32_adc_debugfs_reg_access'
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Suggestion from coccinelle / coccicheck
CHECK drivers/iio/adc/twl4030-madc.c
drivers/iio/adc/twl4030-madc.c:524:6-15: WARNING: Comparison of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:655:1-43: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:659:2-44: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:664:1-43: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:498:2-34: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:510:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:511:2-11: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:531:2-19: WARNING: Assignment of 0/1 to bool variable
drivers/iio/adc/twl4030-madc.c:532:2-11: WARNING: Assignment of 0/1 to bool variable
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Reduces local boilerplate.
Suggested by coccinelle.
CHECK drivers/iio/adc/xilinx-xadc-core.c
drivers/iio/adc/xilinx-xadc-core.c:1184:1-11: WARNING: Use devm_platform_ioremap_resource for xadc -> base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Manish Narani <manish.narani@xilinx.com>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Coccinelle noticed:
CHECK drivers/iio/adc/cpcap-adc.c
drivers/iio/adc/cpcap-adc.c:1009:9-34: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT
As far as I can see this is a simple case of it should be specified
but isn't.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Avoid local boilerplate.
Suggested by coccinelle via coccicheck.
CHECK drivers/iio/adc/meson_saradc.c
drivers/iio/adc/meson_saradc.c:1218:1-5: WARNING: Use devm_platform_ioremap_resource for base
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reduce local boilerplate.
Identified by coccinelle
drivers/iio/adc/exynos_adc.c:792:1-11: WARNING: Use devm_platform_ioremap_resource for info -> regs
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Nothing stops data being of type __be16, which fixes the warning:
CHECK drivers/iio/adc/stmpe-adc.c
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
drivers/iio/adc/stmpe-adc.c:202:29: warning: cast to restricted __be16
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: <philippe.schenker@toradex.com>
Cleans up the sparse warning:
CHECK drivers/iio/adc/at91-sama5d2_adc.c
drivers/iio/adc/at91-sama5d2_adc.c:1486:31: warning: Using plain integer as NULL pointer
drivers/iio/adc/at91-sama5d2_adc.c:1509:31: warning: Using plain integer as NULL pointer
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
This is a new driver for the ST-Ericsson AB8500 GPADC, which
replaces the old driver in drivers/mfd/ab8500-gpadc.c and
thus gets rid of another necessarily different custom driver
from the times before IIO existed.
The AB8500 GPADC can convert 10 different channels and these
are used for monitoring voltages in the U8500 chipset, some
are used for battery charging, some for temperature
monitoring.
As this is very core functionality that a lot of drivers
depend on and was formerly compiled in with the AB8500 core
driver, we deafault it to 'y' in Kconfig: it can be compiled
out but it is really not advisible: the platform can
for example overheat if we do.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Exposes the ADC device present on, at least, Intel Merrifield platform.
Based on work done by:
Yang Bin <bin.yang@intel.com>
Huiquan Zhong <huiquan.zhong@intel.com>
Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Pavan Kumar S <pavan.kumar.s@intel.com>
Though it has been heavily rewritten for upstream.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maxim's max12xx series is very similar to the max10xx series, with the
difference of the measurements depth which is upgraded from 10 to 12
bits per channel. Everything else looks the same.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Maxim's max1027/29/31 series returns the measured voltages with a
resolution of 10 bits. There is a very similar series, max1227/29/31
which works identically but uses a resolution of 12 bits. Prepare the
support for these chips by turning the 'depth' into a macro parameter
instead of hardcoding it everywhere. Also reorganize just a bit the
macros at the top to avoid repeating tens of lines when adding support
for a new chip.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All the registers are configured by the driver, let's reset the chip
at probe time, avoiding any conflict with a possible earlier
configuration.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The chip has a 'start conversion' and a 'end of conversion' pair of
pins. They can be used but this is absolutely not mandatory as regular
polling of the value is totally fine with the current internal
clocking setup. Turn the interrupts optional and do not error out if
they are not inquired in the device tree. This has the effect to
prevent triggered buffers use though.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Until now, only write operations were supported. Force two bytes read
operation when reading, which should fit most of the development
purposes. Of course, extended operations like buffered reads on
multiple channels or even temperature + voltage reads will not be read
entirely. Usually, just starting a new operation will work but in any
case a software reset (done through the debufs interface too) will
return the device in a usable state.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Third version with the adis rework set dropped as better to just have
a fresh version of that at some future date.
The usual mixed backs of new device support being added to drivers,
long term reworks continuing and little per driver cleanups and
features.
Also a few trivial counter subsystem tidy ups on behalf of William.
Core new feature
* Device label support. A long requested feature no one got around to
implementing before. Allows DT based provision of a 'label' that
identifies a device uniquely within a system. This differs from existing
'name' which is meant to be the part number.
New device support
* ingenic-adc
- Support for the JZ4770 SoC ADC including bindings.
* inv_mpu6050
- Add support for magnetometer in MPU925x parts.
Fiddly to do as this is actually a separate device sitting inside the
package, but with the master device being able to schedule reads etc.
Will only run if the auxiliary bus is not in use for any other devices.
Features
* ad7192
- Userspace calibration controls to do zero and full scale.
* st_lsm6dsx
- Enable latched interrupts by default for sensors events with related clear.
- Motion events and related wakeup source. This needed quite a bit of
refactoring as well.
Cleanups and minor features
* ad7192
- sysfs ABI docs
* ad7949
- Remove code to readback configuration word as driver never actually enabled
it.
- Fix incorrect xfer length. Not actually known to cause problems other
than wasted bus usage.
* adis16080
- Replace core mlock usage with local lock with more appropriate scope.
* adis16130
- Remove pointless mlock usage.
* adis16240
- Remove include of gpio.h as no gpio usage.
* atlas-ph-sensor
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* bh1750
- Fix up a static compiler warning and make the code more readable.
- yaml conversion of binding + MAINTAINERS entry.
* bmp280
- Drop a stray newline.
* cm36651
- Drop a redundant assignment
* itg3200
- Alignment cleanup.
* max31856
- Add missing of_node and parent references, useful to identify the device.
* sc27xx_adc
- Use devm_hwspin_lock_request_specific rather than local rolled version.
* stm32-lptimer counter
- kernel-doc warning.
* stm32-timer counter
- kernel-doc warning.
- Alignment cleanup.
* sx9500
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tcs3414
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
-----BEGIN PGP SIGNATURE-----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=nIWU
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.5a-take3' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of IIO new device support, cleanups and features for the 5.5 cycle
Third version with the adis rework set dropped as better to just have
a fresh version of that at some future date.
The usual mixed backs of new device support being added to drivers,
long term reworks continuing and little per driver cleanups and
features.
Also a few trivial counter subsystem tidy ups on behalf of William.
Core new feature
* Device label support. A long requested feature no one got around to
implementing before. Allows DT based provision of a 'label' that
identifies a device uniquely within a system. This differs from existing
'name' which is meant to be the part number.
New device support
* ingenic-adc
- Support for the JZ4770 SoC ADC including bindings.
* inv_mpu6050
- Add support for magnetometer in MPU925x parts.
Fiddly to do as this is actually a separate device sitting inside the
package, but with the master device being able to schedule reads etc.
Will only run if the auxiliary bus is not in use for any other devices.
Features
* ad7192
- Userspace calibration controls to do zero and full scale.
* st_lsm6dsx
- Enable latched interrupts by default for sensors events with related clear.
- Motion events and related wakeup source. This needed quite a bit of
refactoring as well.
Cleanups and minor features
* ad7192
- sysfs ABI docs
* ad7949
- Remove code to readback configuration word as driver never actually enabled
it.
- Fix incorrect xfer length. Not actually known to cause problems other
than wasted bus usage.
* adis16080
- Replace core mlock usage with local lock with more appropriate scope.
* adis16130
- Remove pointless mlock usage.
* adis16240
- Remove include of gpio.h as no gpio usage.
* atlas-ph-sensor
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* bh1750
- Fix up a static compiler warning and make the code more readable.
- yaml conversion of binding + MAINTAINERS entry.
* bmp280
- Drop a stray newline.
* cm36651
- Drop a redundant assignment
* itg3200
- Alignment cleanup.
* max31856
- Add missing of_node and parent references, useful to identify the device.
* sc27xx_adc
- Use devm_hwspin_lock_request_specific rather than local rolled version.
* stm32-lptimer counter
- kernel-doc warning.
* stm32-timer counter
- kernel-doc warning.
- Alignment cleanup.
* sx9500
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tcs3414
- Improve logical ordering of buffer predisable / postenable functions.
This is part of a longer term rework Alexandru is driving towards.
* tag 'iio-for-5.5a-take3' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (41 commits)
iio: pressure: bmp280: remove stray newline
iio: adc: sc27xx: Use devm_hwspin_lock_request_specific() to simplify code
iio: chemical: atlas-ph-sensor: fix iio_triggered_buffer_predisable() position
iio: gyro: clean up indentation issue
counter: stm32: clean up indentation issue
iio: proximity: sx9500: fix iio_triggered_buffer_{predisable,postenable} positions
iio: core: Add optional symbolic label to device attributes
dt-binding: iio: Add optional label property
iio: gyro: adis16080: replace mlock with own lock
counter: stm32-lptimer-cnt: fix a kernel-doc warning
counter: stm32-timer-cnt: fix a kernel-doc warning
iio: gyro: adis16130: remove mlock usage
MAINTAINERS: add entry for ROHM BH1750 driver
dt-bindings: iio: light: bh1750: convert bindings to yaml
iio: imu: st_lsm6dsx: add motion report function and call from interrupt
iio: imu: st_lsm6dsx: always enter interrupt thread
iio: imu: st_lsm6dsx: add wakeup-source option
iio: imu: st_lsm6dsx: add motion events
iio: imu: st_lsm6dsx: move interrupt thread to core
iio: imu: inv_mpu6050: add fifo support for magnetometer data
...
Change to use devm_hwspin_lock_request_specific() to help to simplify the
cleanup code for drivers requesting one hwlock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
-----BEGIN PGP SIGNATURE-----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=s9EA
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 5.4 cycle.
* adis16400
- Make sure to free memory on a few failure paths.
* adxl372
- Fix wrong fifo depth
- Fix wrong indexing of data from the fifo.
- Perform a reset at startup to avoid a problem with inconsistent state.
* axp288
- This is a fix for a fix. The original fix made sure we kept the
configuration from some firmwares to preserve a bias current.
Unfortunately it appears the previous behaviour was working around
a buggy firmware by overwriting the wrong value it had. Hence
a regression was seen.
* bmc150
- Fix the centre temperature. This was due to an error in one of the
datasheets.
* hx711
- Fix an issue where a badly timed interrupt could lead to a control
line being high long enough to put the device into a low power state.
* meson_sar_adc
- Fix a case where the irq was enabled before everything it uses was
allocated.
* st_lsm6dsx
- Ensure we don't set the sensor sensitivity to 0 as it will force
all readings to 0.
- Fix a wait time for the slave i2c controller when the accelerometer
is not enabled.
* stm32-adc
- Precursor for fix. Move a set of register definitions to a header.
- Fix a race when several ADCs are in use with some using interrupts
to control the dataflow and some using DMA.
* vcnl4000
- Fix a garbage of_match_table in which a string was passed instead
of the intended enum.
* tag 'iio-fixes-for-5.4a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: Fix an undefied reference error in noa1305_probe
iio: light: opt3001: fix mutex unlock race
iio: adc: ad799x: fix probe error handling
iio: light: add missing vcnl4040 of_compatible
iio: light: fix vcnl4000 devicetree hooks
iio: imu: st_lsm6dsx: fix waitime for st_lsm6dsx i2c controller
iio: adc: axp288: Override TS pin bias current for some models
iio: imu: adis16400: fix memory leak
iio: imu: adis16400: release allocated memory on failure
iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
iio: adc: stm32-adc: move registers definitions
iio: accel: adxl372: Perform a reset at start up
iio: accel: adxl372: Fix push to buffers lost samples
iio: accel: adxl372: Fix/remove limitation for FIFO samples
iio: adc: hx711: fix bug in sampling of data
iio: fix center temperature of bmc150-accel-core
iio: imu: st_lsm6dsx: forbid 0 sensor sensitivity
iio: adc: meson_saradc: Fix memory allocation order
Since commit 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe
and reset alert status on probe") the error path is wrong since it
leaves the vref regulator on. Fix this by disabling both regulators.
Fixes: 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models, but it seems our old hardcoded 80ųA bias
current was working around a firmware bug on at least one model laptop.
In order to both have our cake and eat it, this commit adds a dmi based
list of models where we need to override the firmware set bias current and
adds the one model we now know needs this to it: The Lenovo Ideapad 100S
(11 inch version).
Fixes: 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203829
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
End of conversion may be handled by using IRQ or DMA. There may be a
race when two conversions complete at the same time on several ADCs.
EOC can be read as 'set' for several ADCs, with:
- an ADC configured to use IRQs. EOCIE bit is set. The handler is normally
called in this case.
- an ADC configured to use DMA. EOCIE bit isn't set. EOC triggers the DMA
request instead. It's then automatically cleared by DMA read. But the
handler gets called due to status bit is temporarily set (IRQ triggered
by the other ADC).
So both EOC status bit in CSR and EOCIE control bit must be checked
before invoking the interrupt handler (e.g. call ISR only for
IRQ-enabled ADCs).
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move STM32 ADC registers definitions to common header.
This is precursor patch to:
- iio: adc: stm32-adc: fix a race when using several adcs with dma and irq
It keeps registers definitions as a whole block, to ease readability and
allow simple access path to EOC bits (readl) in stm32-adc-core driver.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix bug in sampling function hx711_cycle() when interrupt occures while
PD_SCK is high. If PD_SCK is high for at least 60 us power down mode of
the sensor is entered which in turn leads to a wrong measurement.
Switch off interrupts during a PD_SCK high period and move query of DOUT
to the latest point of time which is at the end of PD_SCK low period.
This bug exists in the driver since it's initial addition. The more
interrupts on the system the higher is the probability that it happens.
Fixes: c3b2fdd0ea ("iio: adc: hx711: Add IIO driver for AVIA HX711")
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
