fec_ptp_check_pps_event will return 1 if FEC_T_TF_MASK caused
an interrupt. Don't return IRQ_NONE in this case.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before queue 0 was always checked if any queue caused an interrupt.
It is better to just mark queue 0 if queue 0 has caused an interrupt.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO header size was defined in many drivers. Factorize the code and
define its size in net/tso.h.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC Receive Control Register has a 14 bit field indicating the
longest frame that may be received. It is being set to 1522. Frames
longer than this are discarded, but counted as being in error.
When using DSA, frames from the switch has an additional header,
either 4 or 8 bytes if a Marvell switch is used. Thus a full MTU frame
of 1522 bytes received by the switch on a port becomes 1530 bytes when
passed to the host via the FEC interface.
Change the maximum receive size to 2048 - 64, where 64 is the maximum
rx_alignment applied on the receive buffer for AVB capable FEC
cores. Use this value also for the maximum receive buffer size. The
driver is already allocating a receive SKB of 2048 bytes, so this
change should not have any significant effects.
Tested on imx51, imx6, vf610.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PHY is missing but expected, e.g. because of a typ0 in the dt
file, it is not possible to open the interface. ip link returns:
RTNETLINK answers: No such device
It is not very obvious what the problem is. Add a netdev_err() in this
case to make it easier to debug the issue.
[ 21.409385] fec 2188000.ethernet eth0: Unable to connect to phy
RTNETLINK answers: No such device
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2b30842b23 ("net: fec: Clear and enable MIB counters on imx51")
introduced fec_enet_clear_ethtool_stats(), but missed to add a stub
for the CONFIG_M5272=y case, causing build failure for the
m5272c3_defconfig.
Add the missing empty stub to fix the build failure.
Fixes: Commit 2b30842b23 ("net: fec: Clear and enable MIB counters on imx51")
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the IMX51 and IMX53 datasheet indicates that the MIB counters
should be cleared during setup. Otherwise random numbers are returned
via ethtool -S. Add a quirk and a function to do this.
Tested on an IMX51.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY require to wait for a bit after the reset GPIO has been
toggled. This adds support for the DT property `phy-reset-post-delay`
which gives the delay in milliseconds to wait after reset.
If the DT property is not given, no delay is observed. Post reset delay
greater than 1000ms are invalid.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The errata ERR007885 HW fix don't add to i.MX6ul ENET IP version,
so add sw workaroud for the chip.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the errata number ERR006358 comment typo.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many boards use i2c/spi expander gpio as phy-reset-gpios and these
gpios maybe registered after fec port, driver should check the return
value of .of_get_named_gpio().
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In aarch64 system, it requires to trasfer ->dev to dma_alloc_coherent()
API, otherwise allocate failed and print kernel warning.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In aarch64 system, the BD pointer is 64bit, and the high-order 32-bits
of the address is effective, so replace usigned with (void *) type to
aovid 64bit address is casted to 32bit in .fec_enet_get_nextdesc() and
.fec_enet_get_prevdesc() functions.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add return value check after calling .of_property_read_u32() to avoid
the warning reported by coverity.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 80cca775cd ("net: fec: cache statistics while device is down")
introduced unconditional statistics-related actions.
However, when driver is compiled with CONFIG_M5272, staticsics-related
definitions do not exist, which results into build errors.
Fix that by adding explicit handling of !defined(CONFIG_M5272) case.
Fixes: 80cca775cd ("net: fec: cache statistics while device is down")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Execution 'ethtool -S' on fec device that is down causes OOPS on Vybrid
board:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0898200
pgd = ddecc000
[e0898200] *pgd=9e406811, *pte=400d1653, *ppte=400d1453
Internal error: : 1008 [#1] SMP ARM
...
Reason of OOPS is that fec_enet_get_ethtool_stats() accesses fec
registers while IPG clock is stopped by PM.
Fix that by caching statistics in fec_enet_private. Cache is initialized
at device probe time, and updated at statistics request time if device
is up, and also just before turning device off on down path.
Additional locking is not needed, since cached statistics is accessed
either before device is registered, or under rtnl_lock().
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 407066f8f3 ("net: fec: Support phys probed from devicetree and
fixed-link")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ac72b7b63 ("net: fec: align IP header in hardware") breaks
networking on mx28.
There is an erratum on mx28 (ENGR121613 - ENET big endian mode
not compatible with ARM little endian) that requires an additional
byte-swap operation to workaround this problem.
So call swap_buffer() prior to performing the IP header alignment
to restore network functionality on mx28.
Fixes: 3ac72b7b63 ("net: fec: align IP header in hardware")
Reported-and-tested-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare, clk_enable and their counterparts (at least the common clk
ones, but also most others) do check for the clk being NULL anyhow (and
return 0 then), so there is no gain when the caller checks, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mac address origin is not dt, you can only safely assign a mac
address after "link up" of the device. If the link is off the clocks are
disabled and because of issues assigning registers when clocks are off the
new mac address cannot be written in .ndo_set_mac_address() on some soc's.
This fix sets the mac address unconditionally in fec_restart(...) and
ensures consistency between fec registers and the network layer.
Signed-off-by: Gavin Schenk <g.schenk@eckelmann.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 9638d19e48 ("net: fec: add netif status check before set mac address")
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC receive accelerator (RACC) supports shifting the data payload of
received packets by 16-bits, which aligns the payload (IP header) on a
4-byte boundary, which is, if not required, at least strongly suggested
by the Linux networking layer.
Without this patch, a huge number of alignment faults will be taken by the
IP stack, as seen in /proc/cpu/alignment:
~/$ cat /proc/cpu/alignment
User: 0
System: 72645 (inet_gro_receive+0x104/0x27c)
Skipped: 0
Half: 0
Word: 0
DWord: 0
Multi: 72645
User faults: 3 (fixup+warn)
This patch was suggested by Andrew Lunn in this message to linux-netdev:
http://marc.info/?l=linux-arm-kernel&m=147465452108384&w=2
and adapted from a patch by Russell King from 2014:
http://git.arm.linux.org.uk/cgit/linux-arm.git/commit/?id=70d8a8a
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX27 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://cache.nxp.com/files/32bit/doc/ref_manual/MCIMX27RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the i.MX25 reference manual, this SoC does not have support
for the receive accelerator (RACC) register at offset 0x1C4.
http://www.nxp.com/files/dsp/doc/ref_manual/IMX25RM.pdf
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of leftover symbol conflicts caused by hashtable.h
being included by netdevice.h; those were not caught as build failure
(they're "only" a warning, but in fact real bugs). Fix those up.
Fixes: e87a8f24c ("net: resolve symbol conflicts with generic hashtable.h")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
- A patch series including both cpuidle and FEC driver changes to
disable deeper idle states when FEC is active while board level
workaround for ERR006687 is not available
- A number patches to fix sparse warnings and spell errors
- A fix for TZIC FIQ translation from VIRQ to HWIRQ
- Support compatible of i.MX7 Solo SoC which has a subset of i.MX7 Dual
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcmFTAAoJEFBXWFqHsHzOxXoH/A5B4yRv82dM9L6KcCYqxc8B
UL8Rt11mMsezj/mSoikPjdDV7rKRcbSyY7ujUs0g9jhdKzl2sCCu9rXtYN+oeDpH
iJrndyQ8+Y0UDitmvZGwyW5HImUKuoMvFjJpg7D3WGs/2wACj9TVrrNl+AWawZXR
B+mNO6vT3MEnflzFKkcZmYhwtMXPmaGDc732pS6sgqBLjAJp8X37wWoWJ2lVG9zf
8fjEfUcB3jqWFr6YYJk/adWEjFwRBQ1QayY994Cxeym9kSo3BXfDJ3wcnG1sdOvF
jsM0fsV75gMQNCy8VqiHTNhLk5DGM5PYKQLrQ8r0yoAwvXLLAbu+gPXJSWrACig=
=yWZX
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
The i.MX SoC changes for 4.8:
- A patch series including both cpuidle and FEC driver changes to
disable deeper idle states when FEC is active while board level
workaround for ERR006687 is not available
- A number patches to fix sparse warnings and spell errors
- A fix for TZIC FIQ translation from VIRQ to HWIRQ
- Support compatible of i.MX7 Solo SoC which has a subset of i.MX7 Dual
* tag 'imx-soc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: add support for i.MX 7Solo
ARM: i.MX: Disable supervisor protect for i.MX51
ARM: imx6: fix missing <soc/imx/cpuidle.h> in cpuidle-imx6q.c
ARM: i.MX: Fix FIQ interrupt handling for TZIC
ARM: imx6: fix static declaration in include/soc/imx/cpuidle.h
ARM: imx6q: export cpuidle functions needed by fec driver
ARM: imx: fix missing include of common.h
ARM: imx: fix missing includes
ARM: imx6: disable deeper idle states when FEC is active w/o HW workaround
ARM: mach-imx6q: fix spelling mistake in error message
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX6UL is a member in i.MX series family, the SOC FEC inherits from
i.MX6SX but removes some IP features, lets define a new type for fec
device.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different i.MX SOC FEC support different features like :
- i.MX6Q/DL FEC does not support AVB and interrupt coalesc
- i.MX6SX/i.MX7D supports AVB and interrupt coalesc
- i.MX6UL/ULL does not support AVB, but support interrupt coalesc
So, add new quirk flag to judge the supported features.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since msleep is based on jiffies the PHY reset could take longer
than expected. So use msleep for values greater than 20 msec otherwise
usleep_range.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i.MX6 Q/DL has an erratum (ERR006687) that prevents the FEC from
waking the CPUs when they are in wait(unclocked) state. As the hardware
workaround isn't applicable to all boards, disable the deeper idle state
when the workaround isn't present and the FEC is in use.
This allows to safely run a kernel with CPUidle enabled on all i.MX6
boards.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net> (for network changes)
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
trivial fix to spelling mistakes and add missing newline in pr_err
messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dirty_tx isn't updated, then dma_unmap_single
can be called twice.
This fixes a
[ 58.420980] ------------[ cut here ]------------
[ 58.425667] WARNING: CPU: 0 PID: 377 at /home/schurig/d/mkarm/linux-4.5/lib/dma-debug.c:1096 check_unmap+0x9d0/0xab8()
[ 58.436405] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x0000000000000000] [size=66 bytes]
encountered by Holger
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: <holgerschurig@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the one
contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the receive path a queue's work bit was cleared unconditionally even
if fec_enet_rx_queue only read out a part of the available packets from
the hardware. This resulted in not reading any packets in the next napi
turn and so packets were delayed or lost.
The obvious fix is to only clear a queue's bit when the queue was
emptied.
Fixes: 4d494cdc92 ("net: fec: change data structure to support multiqueue")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the fec driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 55cd48c821 ("net: fec: stop the "rcv is not +last, " error
messages") introduces a write to a register that does not exist in
Coldfire.
Move the FEC_FTRL register access inside the FEC_QUIRK_HAS_RACC 'if' block,
so that we guarantee it will not be used on Coldfire CPUs.
Reported-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
is actually "active high". Thanks for Troy Kisky for pointing
that out.
Since the patch is in linux-next, this patch is incremental and doesn't
replace the original patch.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
