The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the implementation of __spi_validate(), spi core will set transfer
bits_per_word and max speed as spi device default if it is not set for
this transfer. So we can remove the same implementation in this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The only remaining feature of spi-bitbang used by this driver is the
chipselect() callback, which just does conditional GPIO.
This is handled fine by the SPI core's spi_set_cs(), hence switch the
driver to use the core message handling through our own transfer_one()
method.
As the (optional) GPIO CS is no longer deasserted at spi_master.setup()
time (through spi_bitbang_setup() and the spi_bitbang.chipselect()
callback), we now have to take care of that ourselves.
Remove the call to spi_master_put() in sh_msiof_spi_remove(), as our SPI
master is now registered using devm_spi_register_master()
(spi_bitbang_start() uses the non-managed version).
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so the spi core will reject transfers that attempt
to use an unsupported bits_per_word value.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move clock management and pin configuration from the bitbang chipselect()
method to the SPI core prepare_message() and unprepare_message() methods.
As spi_master.{,un}prepare_message() is guaranteed to be called in
matching pairs, the clock management synchronization is no longer needed.
As sh_msiof_spi_set_pin_regs() is no longer called at spi_master.setup()
time (through spi_bitbang_setup() and the spi_bitbang.chipselect()
callback), we now have to take care of that ourselves.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for the MSIOF variant in the R-Car H2 (r8a7790) and M2
(r8a7791) SoCs.
Binding documentation:
- Add future-proof "renesas,msiof-<soctype>" compatible values,
- The default for "renesas,rx-fifo-size" is 256 on R-Car H2 and M2,
- "renesas,tx-fifo-size" and "renesas,rx-fifo-size" are deprecated for
soctype-specific bindings,
- Add example bindings.
Implementation:
- MSIOF on R-Car H2 and M2 requires the transmission of dummy data if
data is being received only (cfr. "Set SICTR.TSCKE to 1" and "Write
dummy transmission data to SITFDR" in paragraph "Transmit and Receive
Procedures" of the Hardware User's Manual).
- As RX depends on TX, MSIOF on R-Car H2 and M2 also lacks the RSCR
register (Receive Clock Select Register), and some bits in the RMDR1
(Receive Mode Register 1) and TMDR2 (Transmit Mode Register 2)
registers.
- Use the recently introduced SPI_MASTER_MUST_TX flag to enable support
for dummy transmission in the SPI core, and to differentiate from other
MSIOF implementations in code paths that need this.
- New DT compatible values ("renesas,msiof-r8a7790" and
"renesas,msiof-r8a7791") are added, as well as new platform device
names ("spi_r8a7790_msiof" and "spi_r8a7791_msiof").
- The default RX FIFO size is 256 words on R-Car H2 and M2.
This is loosely based on a set of patches from Takashi Yoshii
<takasi-y@ops.dti.ne.jp>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
As different variants of MSIOF have different FIFO sizes, move the default
FIFO sizes to a new struct sh_msiof_chipdata, pointed to from the device
ID data.
[Moved ifdef to fix build -- broonie]
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Documentation:
- Add missing "interrupt-parent", "#address-cells", "#size-cells", and
"clocks" properties,
- Add missing default values for "num-cs", "renesas,tx-fifo-size" and
"renesas,rx-fifo-size",
- Add a reference to the pinctrl documentation.
Implementation:
- As "num-cs" is marked optional, provide a sensible default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
In current implementation, CS is controlled by GPIO, which is passed
through spi->controller_data. However, the MSIOF HW module has a function
to output CS by itself, which is already enabled and actual switch will be
done by pinmux.
Store the GPIO number in the core cs_gpio field, and ignore it if it is
an invalid (negative) GPIO number.
Loosely based on a patch from Takashi Yoshii <takasi-y@ops.dti.ne.jp>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both spi_transfer.speed_hz and spi_master.max_speed_hz are u32
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
DT doesn't instantiate SPI children if spi_master.dev.of_node is not set up
properly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set hardware CS(CS control function on MSIOF <-> GPIO CS) polarity
according to SPI_CS_HIGH flag on spi->mode.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
Truncation on integer division in sh_msiof_spi_set_clk_regs()
results in insufficient transfer frequency (> max_speed_freq).
For example, source 52MHz, required max 6MHz
52/6 = 8.6 --> 8, then 1/8 table selected,
and result in 52/8 = 6.5 MHz (>6MHz)
Rounding it up is a simple solution.
52/6 = 8.6 --> 9, then 1/16 table selected,
and result in 52/16 = 3.25 MHz
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
Get the driver ready for the migration to the common clock framework by
calling clk_prepare() and clk_unprepare(). The calls are added in the
probe and remove handlers as the clk_enable() and clk_disable() calls
are located in atomic context and there's no callback function in
non-atomic context that can be used to prepare/unprepare the clock.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This simplifies error and cleanup code paths.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cast pointers to uintptr_t instead of unsigned int. This fixes warnings
on platforms where pointers have a different size than int.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Previously the runtime PM API insisted on having callbacks for everything
but this requirement was removed a while ago so the empty callbacks can
also be removed.
Signed-off-by: Mark Brown <broonie@linaro.org>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds the capability to retrieve setup data from the device tree
node. The usage of platform data is still available.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
clk_get() no longer needs a character string for associating the right
clock as this is done via the device struct now.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We are clipping down the presence of module.h, since it was
everywhere. If you really need it, you better call it out,
as per this changeset.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
For simple modules that contain a single platform_driver without any
additional setup code then ends up being a block of duplicated
boilerplate. This patch adds a new macro, module_platform_driver(),
which replaces the module_init()/module_exit() registrations with
template functions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Magnus Damm <magnus.damm@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>