Add dwmac-intel-plat to enable the stmmac driver in Intel Keem Bay.
Also add fix_mac_speed and tx_clk in order to change link speeds.
This is required as mac_speed_o is not connected in the
Intel Keem Bay SoC.
Signed-off-by: Rusaimi Amira Ruslan <rusaimi.amira.rusaimi@intel.com>
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4 does not look for HASHTBLMEMCRCERR and CMDTIDERR
bits in LE_DB_INT_CAUSE register, but these are enabled
in LE_DB_INT_ENABLE. So, add error handlers to LE
interrupt handler to emit a warning or alert message
for hash table mem crc and cmd tid errors
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PTP clock and uses it in Octeontx2
network device. PTP clock uses mailbox calls to
access the hardware counter on the RVU side.
Co-developed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Precision Timestamping block found on Octeontx2
platform is an independent coprocessor and has
internal PTP hardware clock. Once configured PTP
runs independently and when a packet arrives
CGX hardware block gets the current timestamp
from PTP block and forwards the packet to NIX
by prepending timestamp to the packet.
This patch adds the pci driver for PTP block.
The driver gets registered by AF driver and does
initial configuration and exposes a mailbox function to
read and adjust PTP hardware clock. The mailbox function
is called by AF consumers like netdev drivers or
userspace drivers. Since PTP being a single block
in platform this driver helps in accessing PTP
block by any AF consumer.
Co-developed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Aleksey Makarov <amakarov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four new mbox messages ids and handler are added in order to
enable or disable timestamping procedure on tx and rx side.
Additionally when PTP is enabled, the packet parser must skip
over 8 bytes and start analyzing packet data there. To make NPC
profiles work seemlesly PTR_ADVANCE of IKPU is set so that
parsing can be done as before when all data pointers
are shifted by 8 bytes automatically.
Co-developed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Zyta Szpak <zyta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case recovery was not successful, netdev still should be
present. But we should clear cdev if something bad happens
on recovery.
We also check cdev for null on dev close. That could be a case
if recovery was not successful.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gather and push out full device dump to devlink.
Device dump is the same as with `ethtool -d`, but now its generated
exactly at the moment bad thing happens.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove forcible recovery trigger and put it as a normal devlink
callback.
This allows user to enable/disable it via
devlink health set pci/0000:03:00.0 reporter fw_fatal auto_recover false
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devlink_health_report to push error indications.
We implement this in qede via callback function to make it possible
to reuse the same for other drivers sitting on top of qed in future.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we declare health reporter ops (empty for now)
and register these in qed probe and remove callbacks.
This way we get devlink attached to all kind of qed* PCI
device entities: networking or storage offload entity.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we return existing fw & mfw versions, we also fetch device's
serial number:
~$ sudo ~/iproute2/devlink/devlink dev info
pci/0000:01:00.1:
driver qed
board.serial_number REE1915E44552
versions:
running:
fw.app 8.42.2.0
stored:
fw.mgmt 8.52.10.0
MFW and FW are different firmwares on device.
Management is a firmware responsible for link configuration and
various control plane features. Its permanent and resides in NVM.
Running FW (or fastpath FW) is an embedded microprogram implementing
all the packet processing, offloads, etc. This FW is being loaded
on each start by the driver from FW binary blob.
The base device specific structure (qed_dev_info) was not directly
available to the base driver before. Thus, here we create and store
a private copy of this structure in qed_dev root object to
access the data.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces stubs in kconfig help entries with an actual description.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink instance lifecycle was linked to qed_dev object,
that caused devlink to be recreated on each recovery.
Changing it by making higher level driver (qede) responsible for its
life. This way devlink now survives recoveries.
qede now stores devlink structure pointer as a part of its device
object, devlink private data contains a linkage structure,
qed_devlink.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are extending devlink infrastructure, thus move the existing
stuff into a new file qed_devlink.c
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTYS register is used to report and configure the port type and
speed. Currently, internal bits in the register are used the same way
other bits are used.
Using the internal bits can cause bad parameter firmware errors. For
example, trying to write to internal bit 25 returns:
EMAD reg access failed (tid=53e2bffa00004310,reg_id=5004(ptys),type=write,status=7(bad parameter))
Remove the internal bits from the PTYS register, so that it is no longer
possible to pass them to firmware.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Spectrum-{2,3} ASICs the minimum burst size of the packet trap
policers needs to be 40% of the configured rate. Otherwise, intermittent
drops are observed even when the incoming packet rate is slightly lower
than the configured policer rate.
Adjust the burst size of the registered packet trap policers so that
they do not violate above mentioned limitation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Nothing earth shattering here, lots of small fixes (f.e. missing RCU
protection, bad ref counting, missing memset(), etc.) all over the
place:
1) Use get_file_rcu() in task_file iterator, from Yonghong Song.
2) There are two ways to set remote source MAC addresses in macvlan
driver, but only one of which validates things properly. Fix this.
From Alvin Šipraga.
3) Missing of_node_put() in gianfar probing, from Sumera
Priyadarsini.
4) Preserve device wanted feature bits across multiple netlink
ethtool requests, from Maxim Mikityanskiy.
5) Fix rcu_sched stall in task and task_file bpf iterators, from
Yonghong Song.
6) Avoid reset after device destroy in ena driver, from Shay
Agroskin.
7) Missing memset() in netlink policy export reallocation path, from
Johannes Berg.
8) Fix info leak in __smc_diag_dump(), from Peilin Ye.
9) Decapsulate ECN properly for ipv6 in ipv4 tunnels, from Mark
Tomlinson.
10) Fix number of data stream negotiation in SCTP, from David Laight.
11) Fix double free in connection tracker action module, from Alaa
Hleihel.
12) Don't allow empty NHA_GROUP attributes, from Nikolay Aleksandrov"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (46 commits)
net: nexthop: don't allow empty NHA_GROUP
bpf: Fix two typos in uapi/linux/bpf.h
net: dsa: b53: check for timeout
tipc: call rcu_read_lock() in tipc_aead_encrypt_done()
net/sched: act_ct: Fix skb double-free in tcf_ct_handle_fragments() error flow
net: sctp: Fix negotiation of the number of data streams.
dt-bindings: net: renesas, ether: Improve schema validation
gre6: Fix reception with IP6_TNL_F_RCV_DSCP_COPY
hv_netvsc: Fix the queue_mapping in netvsc_vf_xmit()
hv_netvsc: Remove "unlikely" from netvsc_select_queue
bpf: selftests: global_funcs: Check err_str before strstr
bpf: xdp: Fix XDP mode when no mode flags specified
selftests/bpf: Remove test_align leftovers
tools/resolve_btfids: Fix sections with wrong alignment
net/smc: Prevent kernel-infoleak in __smc_diag_dump()
sfc: fix build warnings on 32-bit
net: phy: mscc: Fix a couple of spelling mistakes "spcified" -> "specified"
libbpf: Fix map index used in error message
net: gemini: Fix missing free_netdev() in error path of gemini_ethernet_port_probe()
net: atlantic: Use readx_poll_timeout() for large timeout
...
23 fixes in 5 drivers (qla2xxx, ufs, scsi_debug, fcoe, zfcp). The
bulk of the changes are in qla2xxx and ufs and all are mostly small
and definitely don't impact the core.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCX0CxgiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVI9AP40cRrH
p0wrE1fKUyj+LbtnWrrHUXsuknS3Sf58zyPeEAEA3qxxLspTxWgLuSnT/KC2gqFB
Kv/XJyKM9CnRg7Uo4mo=
=GRmA
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"23 fixes in 5 drivers (qla2xxx, ufs, scsi_debug, fcoe, zfcp). The bulk
of the changes are in qla2xxx and ufs and all are mostly small and
definitely don't impact the core"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (23 commits)
Revert "scsi: qla2xxx: Disable T10-DIF feature with FC-NVMe during probe"
Revert "scsi: qla2xxx: Fix crash on qla2x00_mailbox_command"
scsi: qla2xxx: Fix null pointer access during disconnect from subsystem
scsi: qla2xxx: Check if FW supports MQ before enabling
scsi: qla2xxx: Fix WARN_ON in qla_nvme_register_hba
scsi: qla2xxx: Allow ql2xextended_error_logging special value 1 to be set anytime
scsi: qla2xxx: Reduce noisy debug message
scsi: qla2xxx: Fix login timeout
scsi: qla2xxx: Indicate correct supported speeds for Mezz card
scsi: qla2xxx: Flush I/O on zone disable
scsi: qla2xxx: Flush all sessions on zone disable
scsi: qla2xxx: Use MBX_TOV_SECONDS for mailbox command timeout values
scsi: scsi_debug: Fix scp is NULL errors
scsi: zfcp: Fix use-after-free in request timeout handlers
scsi: ufs: No need to send Abort Task if the task in DB was cleared
scsi: ufs: Clean up completed request without interrupt notification
scsi: ufs: Improve interrupt handling for shared interrupts
scsi: ufs: Fix interrupt error message for shared interrupts
scsi: ufs-pci: Add quirk for broken auto-hibernate for Intel EHL
scsi: ufs-mediatek: Fix incorrect time to wait link status
...
This patch seperates inline ipsec functionality from coprocessor
driver chcr. Now inline ipsec is separate ULD, moved from
"drivers/crypto/chelsio/" to "drivers/net/ethernet/chelsio/inline_crypto/ch_ipsec/"
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
chelsio inline tls driver(chtls) is mostly overlaps with NIC drivers
but currenty it is part of crypto driver, so move it out to appropriate
directory for better maintenance.
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In qed_rdma_destroy_cq() the result of dma_alloc_coherent() is cast from
void* unnecessarily. Remove cast.
Issue identified with Coccinelle.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both the driver and the firmware supports QinQ the flow key
structure that is send to the firmware is updated as the old
method of matching on VLAN did not allow for space to add another
VLAN tag. VLAN flows can now also match on the tpid field, not
constrained to just 0x8100 as before.
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a check to make sure the total length of the flow key sent to the
firmware stays within the supported limit.
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 filters can occupy up to 4 slots and will exhaust HPFILTER
region much sooner. So, continue searching for free slots in the
HASH or NORMAL filter regions, as long as the rule's priority does
not conflict with existing rules in those regions.
Signed-off-by: Rahul Kundu <rahul.kundu@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Truncation of DMA_BIT_MASK to 32-bit dma_addr_t is semantically safe,
but the compiler was warning because it was happening implicitly.
Insert explicit casts to suppress the warnings.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace alloc_etherdev_mq with devm_alloc_etherdev_mqs. In this way,
when probe fails, netdev can be freed automatically.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit
8dcf2ad39f ("net: atlantic: add hwmon getter for MAC temperature")
implemented a read callback with an udelay(10000U). This fails to
compile on ARM because the delay is >1ms. I doubt that it is needed to
spin for 10ms even if possible on x86.
>From looking at the code, the context appears to be preemptible so using
usleep() should work and avoid busy spinning.
Use readx_poll_timeout() in the poll loop.
Fixes: 8dcf2ad39f ("net: atlantic: add hwmon getter for MAC temperature")
Cc: Mark Starovoytov <mstarovoitov@marvell.com>
Cc: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-and-tested-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver reads RX and TX subCRQ handle array directly from
a DMA-mapped buffer address when it needs to make a H_SEND_SUBCRQ
hcall. This patch stores that information in the ibmvnic_sub_crq_queue
structure instead of reading from the buffer received at login. The
overall goal of this patch is to parse relevant information from the
login response buffer and store it in the driver's private data
structures so that we don't need to read directly from the buffer and
can then free up that memory.
Signed-off-by: Cristobal Forno <cforno12@linux.ibm.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most statistics in ena driver are incremented, meaning that a stat's
value is a sum of all increases done to it since driver/queue
initialization.
This patch makes all statistics this way, effectively making missed_tx
statistic incremental.
Also added a comment regarding rx_drops and tx_drops to make it
clearer how these counters are calculated.
Fixes: 11095fdb71 ("net: ena: add statistics for missed tx packets")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ena_del_napi_in_range() function unregisters the napi handler for
rings in a given range.
This function had the following WARN_ON macro:
WARN_ON(ENA_IS_XDP_INDEX(adapter, i) &&
adapter->ena_napi[i].xdp_ring);
This macro prints the call stack if the expression inside of it is
true [1], but the expression inside of it is the wanted situation.
The expression checks whether the ring has an XDP queue and its index
corresponds to a XDP one.
This patch changes the expression to
!ENA_IS_XDP_INDEX(adapter, i) && adapter->ena_napi[i].xdp_ring
which indicates an unwanted situation.
Also, change the structure of the function. The napi handler is
unregistered for all rings, and so there's no need to check whether the
index is an XDP index or not. By removing this check the code becomes
much more readable.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset work is scheduled by the timer routine whenever it
detects that a device reset is required (e.g. when a keep_alive signal
is missing).
When releasing device resources in ena_destroy_device() the driver
cancels the scheduling of the timer routine without destroying the reset
work explicitly.
This creates the following bug:
The driver is suspended and the ena_suspend() function is called
-> This function calls ena_destroy_device() to free the net device
resources
-> The driver waits for the timer routine to finish
its execution and then cancels it, thus preventing from it
to be called again.
If, in its final execution, the timer routine schedules a reset,
the reset routine might be called afterwards,and a redundant call to
ena_restore_device() would be made.
By changing the reset routine we allow it to read the device's state
accurately.
This is achieved by checking whether ENA_FLAG_TRIGGER_RESET flag is set
before resetting the device and making both the destruction function and
the flag check are under rtnl lock.
The ENA_FLAG_TRIGGER_RESET is cleared at the end of the destruction
routine. Also surround the flag check with 'likely' because
we expect that the reset routine would be called only when
ENA_FLAG_TRIGGER_RESET flag is set.
The destruction of the timer and reset services in __ena_shutoff() have to
stay, even though the timer routine is destroyed in ena_destroy_device().
This is to avoid a case in which the reset routine is scheduled after
free_netdev() in __ena_shutoff(), which would create an access to freed
memory in adapter->flags.
Fixes: 8c5c7abdeb ("net: ena: add power management ops to the ENA driver")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After making use of the gro_flush_timeout attribute I once got a
tx timeout due to an interrupt that wasn't handled. Seems using
irq_enabled can be racy, and it's not needed any longer anyway,
so remove it. I've never seen a report about such a race before,
therefore treat the change as an improvement.
There's just one small drawback: If a legacy PCI interrupt is used,
and if this interrupt is shared with a device with high interrupt
rate, then we may handle interrupts even if NAPI disabled them,
and we may see a certain performance decrease under high network load.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the return value of napi_complete_done(), this allows users to
use the gro_flush_timeout sysfs attribute as an alternative to classic
interrupt coalescing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even after Tx queues are marked stopped, there exists a
small window where the current packet in the normal Tx
path is still being sent out and loopback selftest ends
up corrupting the same Tx ring. So, ensure selftest takes
the Tx lock to synchronize access the Tx ring.
Fixes: 7235ffae3d ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Work request used for sending loopback packet needs to add
the firmware work request only once. So, fix by using
correct structure size.
Fixes: 7235ffae3d ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a couple of unused #defines in cs89x0.h.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If efx_nic_init_interrupt fails, or was never run (e.g. due to an earlier
failure in ef100_net_open), freeing irqs in efx_nic_fini_interrupt is not
needed and will cause error messages and stack traces.
So instead, only do this if efx_nic_init_interrupt successfully completed,
as indicated by the new efx->irqs_hooked flag.
Fixes: 965b549f3c ("sfc_ef100: implement ndo_open/close and EVQ probing")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an ef100_net_open() fails, ef100_net_stop() may be called without
channel->rps_flow_id having been written; thus it may hold the address
freed by a previous ef100_net_stop()'s call to efx_remove_filters().
This then causes a double-free when efx_remove_filters() is called
again, leading to a panic.
To prevent this, after freeing it, overwrite it with NULL.
Fixes: a9dc3d5612 ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
