To more accurately reflect that it is purely a routing
cache lookup key and is used in no other context.
Signed-off-by: David S. Miller <davem@davemloft.net>
Slow path output route resolution always makes sure that
->{saddr,daddr} are set, and also if we trigger into IPSEC resolution
we initialize them as well, because xfrm_lookup() expects them to be
fully resolved.
But if we hit the fast path and flowi4->flowi4_proto is zero, we won't
do this initialization.
Therefore, move the IPSEC path initialization to the route cache
lookup fast path to make sure these are always set.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make dst_alloc() and it's users explicitly initialize the entire
entry.
The zero'ing done by kmem_cache_zalloc() was almost entirely
redundant.
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolved logic conflicts causing a build failure due to
drivers/net/r8169.c changes using a patch from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_select_default() is a complete NOP, and completely pointless
to invoke, when we have no more than 1 default route installed.
And this is far and away the common case.
So remember how many prefixlen==0 routes we have in the routing
table, and elide the call when we have no more than one of those.
This cuts output route creation time by 157 cycles on Niagara2+.
In order to add the new int to fib_table, we have to correct the type
of ->tb_data[] to unsigned long, otherwise the private area will be
unaligned on 64-bit systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
This makes sk_buff available for other use in fib_validate_source().
Signed-off-by: Michael Smith <msmith@cbnco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1018b5c016 ("Set rt->rt_iif more
sanely on output routes.") breaks rt_is_{output,input}_route.
This became the cause to return "IP_PKTINFO's ->ipi_ifindex == 0".
To fix it, this does:
1) Add "int rt_route_iif;" to struct rtable
2) For input routes, always set rt_route_iif to same value as rt_iif
3) For output routes, always set rt_route_iif to zero. Set rt_iif
as it is done currently.
4) Change rt_is_{output,input}_route() to test rt_route_iif
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any operation that:
1) Brings up an interface
2) Adds an IP address to an interface
3) Deletes an IP address from an interface
can potentially invalidate the nh_saddr value, requiring
it to be recomputed.
Perform the recomputation lazily using a generation ID.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2c8cec5c10 (Cache learned PMTU information in inetpeer) added
an extra inet_putpeer() call in ip_rt_update_pmtu().
This results in various problems, since we can free one inetpeer, while
it is still in use.
Ref: http://www.spinics.net/lists/netdev/msg159121.html
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ECN support incorrectly maps ECN BESTEFFORT packets to TC_PRIO_FILLER
(1) instead of TC_PRIO_BESTEFFORT (0)
This means ECN enabled flows are placed in pfifo_fast/prio low priority
band, giving ECN enabled flows [ECT(0) and CE codepoints] higher drop
probabilities.
This is rather unfortunate, given we would like ECN being more widely
used.
Ref : http://www.coverfire.com/archives/2011/03/13/pfifo_fast-and-ecn/
Signed-off-by: Dan Siemon <dan@coverfire.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dave Täht <d@taht.net>
Cc: Jonathan Morton <chromatix99@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On current net-next-2.6, when Linux receives ICMP Type: 3, Code: 4
(Destination unreachable (Fragmentation needed)),
icmp_unreach
-> ip_rt_frag_needed
(peer->pmtu_expires is set here)
-> tcp_v4_err
-> do_pmtu_discovery
-> ip_rt_update_pmtu
(peer->pmtu_expires is already set,
so check_peer_pmtu is skipped.)
-> check_peer_pmtu
check_peer_pmtu is skipped and MTU is not updated.
To fix this, let check_peer_pmtu execute unconditionally.
And some minor fixes
1) Avoid potential peer->pmtu_expires set to be zero.
2) In check_peer_pmtu, argument of time_before is reversed.
3) check_peer_pmtu expects peer->pmtu_orig is initialized as zero,
but not initialized.
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To start doing these conversions, we need to add some temporary
flow4_* macros which will eventually go away when all the protocol
code paths are changed to work on AF specific flowi objects.
Signed-off-by: David S. Miller <davem@davemloft.net>
I intend to turn struct flowi into a union of AF specific flowi
structs. There will be a common structure that each variant includes
first, much like struct sock_common.
This is the first step to move in that direction.
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers are under rcu_read_lock() protection already.
Rename to ip_check_mc_rcu() to make it even more clear.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in commit 44713b67db
("ipv4: Optimize flow initialization in output route lookup."
we can optimize the on-stack flow setup to only initialize
the members which are actually used.
Otherwise we bzero the entire structure, then initialize
explicitly the first half of it.
Signed-off-by: David S. Miller <davem@davemloft.net>
The only necessary parts are the src/dst addresses, the
interface indexes, the TOS, and the mark.
The rest is unnecessary bloat, which amounts to nearly
50 bytes on 64-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
rt->rt_iif is only ever inspected on input routes, for example DCCP
uses this to populate a route lookup flow key when generating replies
to another packet.
Therefore, setting it to anything other than zero on output routes
makes no sense.
Signed-off-by: David S. Miller <davem@davemloft.net>
We burn a lot of useless cycles, cpu store buffer traffic, and
memory operations memset()'ing the on-stack flow used to perform
output route lookups in __ip_route_output_key().
Only the first half of the flow object members even matter for
output route lookups in this context, specifically:
FIB rules matching cares about:
dst, src, tos, iif, oif, mark
FIB trie lookup cares about:
dst
FIB semantic match cares about:
tos, scope, oif
Therefore only initialize these specific members and elide the
memset entirely.
On Niagara2 this kills about ~300 cycles from the output route
lookup path.
Likely, we can take things further, since all callers of output
route lookups essentially throw away the on-stack flow they use.
So they don't care if we use it as a scratch-pad to compute the
final flow key.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Commit 0dbaee3b37 (net: Abstract default ADVMSS behind an
accessor.) introduced a possible crash in tcp_connect_init(), when
dst->default_advmss() is called from dst_metric_advmss()
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only troublesome bit here is __mkroute_output which wants
to override res->fi and res->type, compute those in local
variables instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows avoiding multiple writes to the initial __refcnt.
The most simplest cases of wanting an initial reference of "1"
in ipv4 and ipv6 have been converted, the rest have been left
along and kept at the existing "0".
Signed-off-by: David S. Miller <davem@davemloft.net>
This also allows us to combine all the dst->flags settings and avoid
read/modify/write sequences to this struct member.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of redundancy and unnecessary stack frames
in the output route creation path.
1) Make __mkroute_output() return error pointers.
2) Eliminate ip_mkroute_output() entirely, made possible by #1.
3) Call __mkroute_output() directly and handling the returning error
pointers in ip_route_output_slow().
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that we do not generate the redirect netevent any longer,
because we don't create a new cached route.
Instead, once the new neighbour is bound to the cached route,
we emit a neigh update event instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
The general idea is that if we learn new PMTU information, we
bump the peer genid.
This triggers the dst_ops->check() code to validate and if
necessary propagate the new PMTU value into the metrics.
Learned PMTU information self-expires.
This means that it is not necessary to kill a cached route
entry just because the PMTU information is too old.
As a consequence:
1) When the path appears unreachable (dst_ops->link_failure
or dst_ops->negative_advice) we unwind the PMTU state if
it is out of date, instead of killing the cached route.
A redirected route will still be invalidated in these
situations.
2) rt_check_expire(), rt_worker_func(), et al. are no longer
necessary at all.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we didn't have a routing cache, we would not be able to properly
propagate certain kinds of dynamic path attributes, for example
PMTU information and redirects.
The reason is that if we didn't have a routing cache, then there would
be no way to lookup all of the active cached routes hanging off of
sockets, tunnels, IPSEC bundles, etc.
Consider the case where we created a cached route, but no inetpeer
entry existed and also we were not asked to pre-COW the route metrics
and therefore did not force the creation a new inetpeer entry.
If we later get a PMTU message, or a redirect, and store this
information in a new inetpeer entry, there is no way to teach that
cached route about the newly existing inetpeer entry.
The facilities implemented here handle this problem.
First we create a generation ID. When we create a cached route of any
kind, we remember the generation ID at the time of attachment. Any
time we force-create an inetpeer entry in response to new path
information, we bump that generation ID.
The dst_ops->check() callback is where the knowledge of this event
is propagated. If the global generation ID does not equal the one
stored in the cached route, and the cached route has not attached
to an inetpeer yet, we look it up and attach if one is found. Now
that we've updated the cached route's information, we update the
route's generation ID too.
This clears the way for implementing PMTU and redirects directly in
the inetpeer cache. There is absolutely no need to consult cached
route information in order to maintain this information.
At this point nothing bumps the inetpeer genids, that comes in the
later changes which handle PMTUs and redirects using inetpeers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like metrics, the ICMP rate limiting bits are cached state about
a destination. So move it into the inet_peer entries.
If an inet_peer cannot be bound (the reason is memory allocation
failure or similar), the policy is to allow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Always lookup to see if we have an existing inetpeer entry for
a route. Let FLOWI_FLAG_PRECOW_METRICS merely influence the
"create" argument to rt_bind_peer().
Also, call rt_bind_peer() unconditionally since it is not
possible for rt->peer to be non-NULL at this point.
Signed-off-by: David S. Miller <davem@davemloft.net>
Both fib_trie and fib_hash have a local implementation of
fib_table_select_default(). This is completely unnecessary
code duplication.
Since we now remember the fib_table and the head of the fib
alias list of the default route, we can implement one single
generic version of this routine.
Looking at the fib_hash implementation you may get the impression
that it's possible for there to be multiple top-level routes in
the table for the default route. The truth is, it isn't, the
insert code will only allow one entry to exist in the zero
prefix hash table, because all keys evaluate to zero and all
keys in a hash table must be unique.
Signed-off-by: David S. Miller <davem@davemloft.net>
When an IPSEC SA is still being set up, __xfrm_lookup() will return
-EREMOTE and so ip_route_output_flow() will return a blackhole route.
This can happen in a sndmsg call, and after d33e455337 ("net: Abstract
default MTU metric calculation behind an accessor.") this leads to a
crash in ip_append_data() because the blackhole dst_ops have no
default_mtu() method and so dst_mtu() calls a NULL pointer.
Fix this by adding default_mtu() methods (that simply return 0, matching
the old behavior) to the blackhole dst_ops.
The IPv4 part of this patch fixes a crash that I saw when using an IPSEC
VPN; the IPv6 part is untested because I don't have an IPv6 VPN, but it
looks to be needed as well.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib metric memory in this case is static in the kernel image,
so we don't need to reference count it since it's never going
to go away on us.
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP is going to record metrics for the connection,
so pre-COW the route metrics at route cache entry
creation time.
This avoids several atomic operations that have to
occur if we COW the metrics after the entry reaches
global visibility.
Signed-off-by: David S. Miller <davem@davemloft.net>
Please note that the IPSEC dst entry metrics keep using
the generic metrics COW'ing mechanism using kmalloc/kfree.
This gives the IPSEC routes an opportunity to use metrics
which are unique to their encapsulated paths.
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing metrics are now copy-on-write.
Initially a route entry points it's metrics at a read-only location.
If a routing table entry exists, it will point there. Else it will
point at the all zero metric place-holder called 'dst_default_metrics'.
The writeability state of the metrics is stored in the low bits of the
metrics pointer, we have two bits left to spare if we want to store
more states.
For the initial implementation, COW is implemented simply via kmalloc.
However future enhancements will change this to place the writable
metrics somewhere else, in order to increase sharing. Very likely
this "somewhere else" will be the inetpeer cache.
Note also that this means that metrics updates may transiently fail
if we cannot COW the metrics successfully.
But even by itself, this patch should decrease memory usage and
increase cache locality especially for routing workloads. In those
cases the read-only metric copies stay in place and never get written
to.
TCP workloads where metrics get updated, and those rare cases where
PMTU triggers occur, will take a very slight performance hit. But
that hit will be alleviated when the long-term writable metrics
move to a more sharable location.
Since the metrics storage went from a u32 array of RTAX_MAX entries to
what is essentially a pointer, some retooling of the dst_entry layout
was necessary.
Most importantly, we need to preserve the alignment of the reference
count so that it doesn't share cache lines with the read-mostly state,
as per Eric Dumazet's alignment assertion checks.
The only non-trivial bit here is the move of the 'flags' member into
the writeable cacheline. This is OK since we are always accessing the
flags around the same moment when we made a modification to the
reference count.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dependencies of netfilter realm match: it depends on NET_CLS_ROUTE,
which itself depends on NET_SCHED; this dependency is missing from netfilter.
Since matching on realms is also useful without having NET_SCHED enabled and
the option really only controls whether the tclassid member is included in
route and dst entries, rename the config option to IP_ROUTE_CLASSID and move
it outside of traffic scheduling context to get rid of the NET_SCHED dependeny.
Reported-by: Vladis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The preferred source address is currently ignored for local routes,
which results in all local connections having a src address that is the
same as the local dst address. Fix this by respecting the preferred source
address when it is provided for local routes.
This bug can be demonstrated as follows:
# ifconfig dummy0 192.168.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 192.168.0.1
# ip route change table local local 192.168.0.1 dev dummy0 \
proto kernel scope host src 127.0.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 127.0.0.1
We now establish a local connection and verify the source IP
address selection:
# nc -l 192.168.0.1 3128 &
# nc 192.168.0.1 3128 &
# netstat -ant | grep 192.168.0.1:3128.*EST
tcp 0 0 192.168.0.1:3128 192.168.0.1:33228 ESTABLISHED
tcp 0 0 192.168.0.1:33228 192.168.0.1:3128 ESTABLISHED
Signed-off-by: Joel Sing <jsing@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip_route_output_slow(), instead of allowing a route to be created on
a not UPed device, report -ENETUNREACH immediately.
# ip tunnel add mode ipip remote 10.16.0.164 local
10.16.0.72 dev eth0
# (Note : tunl1 is down)
# ping -I tunl1 10.1.2.3
PING 10.1.2.3 (10.1.2.3) from 192.168.18.5 tunl1: 56(84) bytes of data.
(nothing)
# ./a.out tunl1
# ip tunnel del tunl1
Message from syslogd@shelby at Dec 22 10:12:08 ...
kernel: unregister_netdevice: waiting for tunl1 to become free.
Usage count = 3
After patch:
# ping -I tunl1 10.1.2.3
connect: Network is unreachable
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flush the routing cache only of entries that match the
network namespace in which the purge event occurred.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Like RTAX_ADVMSS, make the default calculation go through a dst_ops
method rather than caching the computation in the routing cache
entries.
Now dst metrics are pretty much left as-is when new entries are
created, thus optimizing metric sharing becomes a real possibility.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all RTAX_ADVMSS metric accesses go through a new helper function,
dst_metric_advmss().
Leave the actual default metric as "zero" in the real metric slot,
and compute the actual default value dynamically via a new dst_ops
AF specific callback.
For stacked IPSEC routes, we use the advmss of the path which
preserves existing behavior.
Unlike ipv4/ipv6, DecNET ties the advmss to the mtu and thus updates
advmss on pmtu updates. This inconsistency in advmss handling
results in more raw metric accesses than I wish we ended up with.
Signed-off-by: David S. Miller <davem@davemloft.net>
Always go through a new ip4_dst_hoplimit() helper, just like ipv6.
This allowed several simplifications:
1) The interim dst_metric_hoplimit() can go as it's no longer
userd.
2) The sysctl_ip_default_ttl entry no longer needs to use
ipv4_doint_and_flush, since the sysctl is not cached in
routing cache metrics any longer.
3) ipv4_doint_and_flush no longer needs to be exported and
therefore can be marked static.
When ipv4_doint_and_flush_strategy was removed some time ago,
the external declaration in ip.h was mistakenly left around
so kill that off too.
We have to move the sysctl_ip_default_ttl declaration into
ipv4's route cache definition header net/route.h, because
currently net/ip.h (where the declaration lives now) has
a back dependency on net/route.h
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to hide all direct accesses, especially writes,
to dst_entry metrics values.
This will allow us to:
1) More easily change how the metrics are stored.
2) Implement COW for metrics.
In particular this will help us put metrics into the inetpeer
cache if that is what we end up doing. We can make the _metrics
member a pointer instead of an array, initially have it point
at the read-only metrics in the FIB, and then on the first set
grab an inetpeer entry and point the _metrics member there.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we test rt->fl.iif against zero, we're seeing if it's
an output or an input route.
Make that explicit with some helper functions.
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems idev field in struct rtable has no special purpose, but adding
extra atomic ops.
We hold refcounts on the device itself (using percpu data, so pretty
cheap in current kernel).
infiniband case is solved using dst.dev instead of idev->dev
Removal of this field means routing without route cache is now using
shared data, percpu data, and only potential contention is a pair of
atomic ops on struct neighbour per forwarded packet.
About 5% speedup on routing test.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations to :
(struct dst_entry)->rt_next
(struct rt_hash_bucket)->chain
And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point using RCU for dst we allocate for a very short time
(used once).
Change dst_release() to take DST_NOCACHE into account, but also change
skb_dst_set_noref() to force a refcount increment for such dst.
This is a _huge_ gain, because we dont waste memory to store xx thousand
of dsts. Instead of queueing them to RCU, we can free them instantly.
CPU caches can stay hot, re-using same memory blocks to hold temporary
dsts.
Note : remove unneeded smp_mb__before_atomic_dec(); in dst_release(),
since atomic_dec_return() implies a full memory barrier.
Stress test, 160.000.000 udp frames sent, IP route cache disabled
(DDOS).
Before:
real 0m38.091s
user 0m13.189s
sys 7m53.018s
After:
real 0m29.946s
user 0m12.157s
sys 7m40.605s
For reference, if IP route cache was enabled :
real 0m32.030s
user 0m10.521s
sys 8m15.243s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change a few checks against the hardcoded broadcast address,
0xffffffff, to ipv4_is_lbcast(). Remove some existing checks
using ipv4_is_lbcast() that are now obviously superfluous.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct dst_ops tracks number of allocated dst in an atomic_t field,
subject to high cache line contention in stress workload.
Switch to a percpu_counter, to reduce number of time we need to dirty a
central location. Place it on a separate cache line to avoid dirtying
read only fields.
Stress test :
(Sending 160.000.000 UDP frames,
IP route cache disabled, dual E5540 @2.53GHz,
32bit kernel, FIB_TRIE, SLUB/NUMA)
Before:
real 0m51.179s
user 0m15.329s
sys 10m15.942s
After:
real 0m45.570s
user 0m15.525s
sys 9m56.669s
With a small reordering of struct neighbour fields, subject of a
following patch, (to separate refcnt from other read mostly fields)
real 0m41.841s
user 0m15.261s
sys 8m45.949s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "fib: RCU conversion of fib_lookup()" removed rcu_read_lock() from
__mkroute_output but left a couple of calls to rcu_read_unlock() in there.
This causes lockdep to complain that the rcu_read_unlock() call in
__ip_route_output_key causes a lock inbalance and quickly crashes the
kernel. The below fixes this for me.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing stress tests with IP route cache disabled, and multi queue
devices, I noticed a very high contention on one rwlock used in
neighbour code.
When many cpus are trying to send frames (possibly using a high
performance multiqueue device) to the same neighbour, they fight for the
neigh->lock rwlock in order to call neigh_hh_init(), and fight on
hh->hh_refcnt (a pair of atomic_inc/atomic_dec_and_test())
But we dont need to call neigh_hh_init() for dst that are used only
once. It costs four atomic operations at least, on two contended cache
lines, plus the high contention on neigh->lock rwlock.
Introduce a new dst flag, DST_NOCACHE, that is set when dst was not
inserted in route cache.
With the stress test bench, sending 160000000 frames on one neighbour,
results are :
Before patch:
real 2m28.406s
user 0m11.781s
sys 36m17.964s
After patch:
real 1m26.532s
user 0m12.185s
sys 20m3.903s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing stress tests with a disabled IP route cache, I found
__mkroute_output() was touching three times in_device atomic refcount.
Use RCU to touch it once to reduce cache line ping pongs.
Before patch
time to perform the test
real 1m42.009s
user 0m12.545s
sys 25m0.726s
Profile :
16109.00 26.4% ip_route_output_slow vmlinux
7434.00 12.2% dst_destroy vmlinux
3280.00 5.4% fib_rules_lookup vmlinux
3252.00 5.3% fib_semantic_match vmlinux
2622.00 4.3% fib_table_lookup vmlinux
2535.00 4.1% dst_alloc vmlinux
1750.00 2.9% _raw_read_lock vmlinux
1532.00 2.5% rt_set_nexthop vmlinux
After patch
real 1m36.503s
user 0m12.977s
sys 23m25.608s
14234.00 22.4% ip_route_output_slow vmlinux
8717.00 13.7% dst_destroy vmlinux
4052.00 6.4% fib_rules_lookup vmlinux
3951.00 6.2% fib_semantic_match vmlinux
3191.00 5.0% dst_alloc vmlinux
1764.00 2.8% fib_table_lookup vmlinux
1692.00 2.7% _raw_read_lock vmlinux
1605.00 2.5% rt_set_nexthop vmlinux
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 and IPv6 have separate neighbour tables, so
the warning messages should be distinguishable.
[ Add a suitable message prefix on the ipv4 side as well -DaveM ]
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__in_dev_get_rtnl(dev_out) is called while RTNL is not held, thus
triggers a lockdep fault.
At this point, we only perform a raw test of dev_out->ip_ptr being NULL,
we dont need to make sure ip_ptr cant changed right after.
We can use rcu_dereference_raw() for this.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Blackhole routes are used when xfrm_lookup() returns -EREMOTE (error
triggered by IKE for example), hence this kind of route is always
temporary and so we should check if a better route exists for next
packets.
Bug has been introduced by commit d11a4dc18b.
Signed-off-by: Jianzhao Wang <jianzhao.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now cmpxchg() is available on all arches, we can use it in
build_ehash_secret() and rt_bind_peer() instead of using spinlocks.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new rt attribute, RTA_MARK, and use it in
rt_fill_info()/inet_rtm_getroute() to support following commands :
ip route get 192.168.20.110 mark NUMBER
ip route get 192.168.20.108 from 192.168.20.110 iif eth1 mark NUMBER
ip route list cache [192.168.20.110] mark NUMBER
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CodingStyle cleanups
EXPORT_SYMBOL should immediately follow the symbol declaration.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addition of rcu_head to struct inet_peer added 16bytes on 64bit arches.
Thats a bit unfortunate, since old size was exactly 64 bytes.
This can be solved, using an union between this rcu_head an four fields,
that are normally used only when a refcount is taken on inet_peer.
rcu_head is used only when refcnt=-1, right before structure freeing.
Add a inet_peer_refcheck() function to check this assertion for a while.
We can bring back SLAB_HWCACHE_ALIGN qualifier in kmem cache creation.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_dev_get() -> __in_dev_get_rcu() in a rcu protected function.
[ Fix build with CONFIG_IP_ROUTE_VERBOSE disabled. -DaveM ]
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid two atomic ops on output device refcount
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid two atomic ops on struct in_device refcount per incoming packet,
if slow path taken, (or route cache disabled)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Lameter mentioned that packets could be dropped in input path
because of rp_filter settings, without any SNMP counter being
incremented. System administrator can have a hard time to track the
problem.
This patch introduces a new counter, LINUX_MIB_IPRPFILTER, incremented
each time we drop a packet because Reverse Path Filter triggers.
(We receive an IPv4 datagram on a given interface, and find the route to
send an answer would use another interface)
netstat -s | grep IPReversePathFilter
IPReversePathFilter: 21714
Reported-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch saves 224 bytes of text on my machine.
__this_cpu_inc() generates a single instruction, using no scratch
registers :
65 ff 04 25 a8 30 01 00 incl %gs:0x130a8
instead of :
48 c7 c2 80 30 01 00 mov $0x13080,%rdx
65 48 8b 04 25 88 ea 00 00 mov %gs:0xea88,%rax
83 44 10 28 01 addl $0x1,0x28(%rax,%rdx,1)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input() is the version returning a refcounted dst, while
ip_route_input_noref() returns a non refcounted one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use low order bit of skb->_skb_dst to tell dst is not refcounted.
Change _skb_dst to _skb_refdst to make sure all uses are catched.
skb_dst() returns the dst, regardless of noref bit set or not, but
with a lockdep check to make sure a noref dst is not given if current
user is not rcu protected.
New skb_dst_set_noref() helper to set an notrefcounted dst on a skb.
(with lockdep check)
skb_dst_drop() drops a reference only if skb dst was refcounted.
skb_dst_force() helper is used to force a refcount on dst, when skb
is queued and not anymore RCU protected.
Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if
!IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in
sock_queue_rcv_skb(), in __nf_queue().
Use skb_dst_force() in dev_requeue_skb().
Note: dst_use_noref() still dirties dst, we might transform it
later to do one dirtying per jiffies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A while back there was a discussion regarding the rt_secret_interval timer.
Given that we've had the ability to do emergency route cache rebuilds for awhile
now, based on a statistical analysis of the various hash chain lengths in the
cache, the use of the flush timer is somewhat redundant. This patch removes the
rt_secret_interval sysctl, allowing us to rely solely on the statistical
analysis mechanism to determine the need for route cache flushes.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse can help us find endianness bugs, but we need to make some
cleanups to be able to more easily spot real bugs.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The the rebuild changes the genid which in turn is used at
the hash calculation. Thus if we don't restart and go on with
inserting the rt will happen in wrong chain.
(Fixed Neil's comment about the index passed into the rt_intern_hash)
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need in getting it 3 times and gcc isn't smart enough
to understand this himself.
This is just a cleanup before the fix (next patch).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP sessions over IPv4 can get stuck if routers between endpoints
do not fragment packets but implement PMTU instead, and we are using
those routers because of an ICMP redirect.
Setup is as follows
MTU1 MTU2 MTU1
A--------B------C------D
with MTU1 > MTU2. A and D are endpoints, B and C are routers. B and C
implement PMTU and drop packets larger than MTU2 (for example because
DF is set on all packets). TCP sessions are initiated between A and D.
There is packet loss between A and D, causing frequent TCP
retransmits.
After the number of retransmits on a TCP session reaches tcp_retries1,
tcp calls dst_negative_advice() prior to each retransmit. This results
in route cache entries for the peer to be deleted in
ipv4_negative_advice() if the Path MTU is set.
If the outstanding data on an affected TCP session is larger than
MTU2, packets sent from the endpoints will be dropped by B or C, and
ICMP NEEDFRAG will be returned. A and D receive NEEDFRAG messages and
update PMTU.
Before the next retransmit, tcp will again call dst_negative_advice(),
causing the route cache entry (with correct PMTU) to be deleted. The
retransmitted packet will be larger than MTU2, causing it to be
dropped again.
This sequence repeats until the TCP session aborts or is terminated.
Problem is fixed by removing redirected route cache entries in
ipv4_negative_advice() only if the PMTU is expired.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xfrm_dst keeps a reference to ipv4 rtable entries on each
cached bundle. The only way to renew xfrm_dst when the underlying
route has changed, is to implement dst_check for this. This is
what ipv6 side does too.
The problems started after 87c1e12b5e
("ipsec: Fix bogus bundle flowi") which fixed a bug causing xfrm_dst
to not get reused, until that all lookups always generated new
xfrm_dst with new route reference and path mtu worked. But after the
fix, the old routes started to get reused even after they were expired
causing pmtu to break (well it would occationally work if the rtable
gc had run recently and marked the route obsolete causing dst_check to
get called).
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
route: Fix caught BUG_ON during rt_secret_rebuild_oneshot()
Call rt_secret_rebuild can cause BUG_ON(timer_pending(&net->ipv4.rt_secret_timer)) in
add_timer as there is not any synchronization for call rt_secret_rebuild_oneshot()
for the same net namespace.
Also this issue affects to rt_secret_reschedule().
Thus use mod_timer enstead.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We added an automatic route cache rebuilding in commit 1080d709fb
but had to correct few bugs. One of the assumption of original patch,
was that entries where kept sorted in a given way.
This assumption is known to be wrong (commit 1ddbcb005c gave an
explanation of this and corrected a leak) and expensive to respect.
Paweł Staszewski reported to me one of his machine got its routing cache
disabled after few messages like :
[ 2677.850065] Route hash chain too long!
[ 2677.850080] Adjust your secret_interval!
[82839.662993] Route hash chain too long!
[82839.662996] Adjust your secret_interval!
[155843.731650] Route hash chain too long!
[155843.731664] Adjust your secret_interval!
[155843.811881] Route hash chain too long!
[155843.811891] Adjust your secret_interval!
[155843.858209] vlan0811: 5 rebuilds is over limit, route caching
disabled
[155843.858212] Route hash chain too long!
[155843.858213] Adjust your secret_interval!
This is because rt_intern_hash() might be fooled when computing a chain
length, because multiple entries with same keys can differ because of
TOS (or mark/oif) bits.
In the rare case the fast algorithm see a too long chain, and before
taking expensive path, we call a helper function in order to not count
duplicates of same routes, that only differ with tos/mark/oif bits. This
helper works with data already in cpu cache and is not be very
expensive, despite its O(N^2) implementation.
Paweł Staszewski sucessfully tested this patch on his loaded router.
Reported-and-tested-by: Paweł Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update rcu_dereference() primitives to use new lockdep-based
checking. The rcu_dereference() in __in6_dev_get() may be
protected either by rcu_read_lock() or RTNL, per Eric Dumazet.
The rcu_dereference() in __sk_free() is protected by the fact
that it is never reached if an update could change it. Check
for this by using rcu_dereference_check() to verify that the
struct sock's ->sk_wmem_alloc counter is zero.
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <1266887105-1528-5-git-send-email-paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add __percpu sparse annotations to net.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
The macro and type tricks around snmp stats make things a bit
interesting. DEFINE/DECLARE_SNMP_STAT() macros mark the target field
as __percpu and SNMP_UPD_PO_STATS() macro is updated accordingly. All
snmp_mib_*() users which used to cast the argument to (void **) are
updated to cast it to (void __percpu **).
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
/proc/net/rt_acct is not created if NET_CLS_ROUTE=n.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to be used together with switch technologies, like RFC3069,
that where the individual ports are not allowed to communicate with
each other, but they are allowed to talk to the upstream router. As
described in RFC 3069, it is possible to allow these hosts to
communicate through the upstream router by proxy_arp'ing.
This patch basically allow proxy arp replies back to the same
interface (from which the ARP request/solicitation was received).
Tunable per device via proc "proxy_arp_pvlan":
/proc/sys/net/ipv4/conf/*/proxy_arp_pvlan
This switch technology is known by different vendor names:
- In RFC 3069 it is called VLAN Aggregation.
- Cisco and Allied Telesyn call it Private VLAN.
- Hewlett-Packard call it Source-Port filtering or port-isolation.
- Ericsson call it MAC-Forced Forwarding (RFC Draft).
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
The motivation for an additional notifier in batched netdevice
notification (rt_do_flush) only needs to be called once per batch not
once per namespace.
For further batching improvements I need a guarantee that the
netdevices are unregistered in order allowing me to unregister an all
of the network devices in a network namespace at the same time with
the guarantee that the loopback device is really and truly
unregistered last.
Additionally it appears that we moved the route cache flush after
the final synchronize_net, which seems wrong and there was no
explanation. So I have restored the original location of the final
synchronize_net.
Cc: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rewrite statistics accumulation to be in terms of structure fields,
not raw u32 additions. Keep them in same order, though.
This is the last user of create_proc_read_entry() in net/,
please NAK all new ones as well as all new ->write_proc, ->read_proc and
create_proc_entry() users. Cc me if there are problems. :-)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generated with the following semantic patch
@@
struct net *n1;
struct net *n2;
@@
- n1 == n2
+ net_eq(n1, n2)
@@
struct net *n1;
struct net *n2;
@@
- n1 != n2
+ !net_eq(n1, n2)
applied over {include,net,drivers/net}.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Sun, 2009-11-22 at 16:31 -0800, David Miller wrote:
> It should be of the form:
> if (x &&
> y)
>
> or:
> if (x && y)
>
> Fix patches, rather than complaints, for existing cases where things
> do not follow this pattern are certainly welcome.
Also collapsed some multiple tabs to single space.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While investigating for network latencies, I found inet_getid() was a
contention point for some workloads, as inet_peer_idlock is shared
by all inet_getid() users regardless of peers.
One way to fix this is to make ip_id_count an atomic_t instead
of __u16, and use atomic_add_return().
In order to keep sizeof(struct inet_peer) = 64 on 64bit arches
tcp_ts_stamp is also converted to __u32 instead of "unsigned long".
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that sys_sysctl is a compatiblity wrapper around /proc/sys
all sysctl strategy routines, and all ctl_name and strategy
entries in the sysctl tables are unused, and can be
revmoed.
In addition neigh_sysctl_register has been modified to no longer
take a strategy argument and it's callers have been modified not
to pass one.
Cc: "David Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Policy routing is not looked up by mark on reverse path filtering.
This fixes it.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use symbols instead of magic constants while checking PMTU discovery
setsockopt.
Remove redundant test in ip_rt_frag_needed() (done by caller).
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's unused.
It isn't needed -- read or write flag is already passed and sysctl
shouldn't care about the rest.
It _was_ used in two places at arch/frv for some reason.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sizing of memory allocations shouldn't depend on the number of physical
pages found in a system, as that generally includes (perhaps a huge amount
of) non-RAM pages. The amount of what actually is usable as storage
should instead be used as a basis here.
Some of the calculations (i.e. those not intending to use high memory)
should likely even use (totalram_pages - totalhigh_pages).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While doing some forwarding benchmarks, I noticed
ip_rt_send_redirect() is rather expensive, even if send_redirects is
false for the device.
Fix is to avoid two atomic ops, we dont really need to take a
reference on in_dev
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Choose saner defaults for xfrm[4|6] gc_thresh values on init
Currently, the xfrm[4|6] code has hard-coded initial gc_thresh values
(set to 1024). Given that the ipv4 and ipv6 routing caches are sized
dynamically at boot time, the static selections can be non-sensical.
This patch dynamically selects an appropriate gc threshold based on
the corresponding main routing table size, using the assumption that
we should in the worst case be able to handle as many connections as
the routing table can.
For ipv4, the maximum route cache size is 16 * the number of hash
buckets in the route cache. Given that xfrm4 starts garbage
collection at the gc_thresh and prevents new allocations at 2 *
gc_thresh, we set gc_thresh to half the maximum route cache size.
For ipv6, its a bit trickier. there is no maximum route cache size,
but the ipv6 dst_ops gc_thresh is statically set to 1024. It seems
sane to select a simmilar gc_thresh for the xfrm6 code that is half
the number of hash buckets in the v6 route cache times 16 (like the v4
code does).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When route caching is disabled (rt_caching returns false), We still use route
cache entries that are created and passed into rt_intern_hash once. These
routes need to be made usable for the one call path that holds a reference to
them, and they need to be reclaimed when they're finished with their use. To be
made usable, they need to be associated with a neighbor table entry (which they
currently are not), otherwise iproute_finish2 just discards the packet, since we
don't know which L2 peer to send the packet to. To do this binding, we need to
follow the path a bit higher up in rt_intern_hash, which calls
arp_bind_neighbour, but not assign the route entry to the hash table.
Currently, if caching is off, we simply assign the route to the rp pointer and
are reutrn success. This patch associates us with a neighbor entry first.
Secondly, we need to make sure that any single use routes like this are known to
the garbage collector when caching is off. If caching is off, and we try to
hash in a route, it will leak when its refcount reaches zero. To avoid this,
this patch calls rt_free on the route cache entry passed into rt_intern_hash.
This places us on the gc list for the route cache garbage collector, so that
when its refcount reaches zero, it will be reclaimed (Thanks to Alexey for this
suggestion).
I've tested this on a local system here, and with these patches in place, I'm
able to maintain routed connectivity to remote systems, even if I set
/proc/sys/net/ipv4/rt_cache_rebuild_count to -1, which forces rt_caching to
return false.
Signed-off-by: Neil Horman <nhorman@redhat.com>
Reported-by: Jarek Poplawski <jarkao2@gmail.com>
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't drop route if we're not caching
I recently got a report of an oops on a route lookup. Maxime was
testing what would happen if route caching was turned off (doing so by setting
making rt_caching always return 0), and found that it triggered an oops. I
looked at it and found that the problem stemmed from the fact that the route
lookup routines were returning success from their lookup paths (which is good),
but never set the **rp pointer to anything (which is bad). This happens because
in rt_intern_hash, if rt_caching returns false, we call rt_drop and return 0.
This almost emulates slient success. What we should be doing is assigning *rp =
rt and _not_ dropping the route. This way, during slow path lookups, when we
create a new route cache entry, we don't immediately discard it, rather we just
don't add it into the cache hash table, but we let this one lookup use it for
the purpose of this route request. Maxime has tested and reports it prevents
the oops. There is still a subsequent routing issue that I'm looking into
further, but I'm confident that, even if its related to this same path, this
patch makes sense to take.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the sake of power saver lovers, use a deferrable timer to fire
rt_check_expire()
As some big routers cache equilibrium depends on garbage collection
done in time, we take into account elapsed time between two
rt_check_expire() invocations to adjust the amount of slots we have to
check.
Based on an initial idea and patch from Tero Kristo
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander V. Lukyanov found a regression in 2.6.29 and made a complete
analysis found in http://bugzilla.kernel.org/show_bug.cgi?id=13339
Quoted here because its a perfect one :
begin_of_quotation
2.6.29 patch has introduced flexible route cache rebuilding. Unfortunately the
patch has at least one critical flaw, and another problem.
rt_intern_hash calculates rthi pointer, which is later used for new entry
insertion. The same loop calculates cand pointer which is used to clean the
list. If the pointers are the same, rtable leak occurs, as first the cand is
removed then the new entry is appended to it.
This leak leads to unregister_netdevice problem (usage count > 0).
Another problem of the patch is that it tries to insert the entries in certain
order, to facilitate counting of entries distinct by all but QoS parameters.
Unfortunately, referencing an existing rtable entry moves it to list beginning,
to speed up further lookups, so the carefully built order is destroyed.
For the first problem the simplest patch it to set rthi=0 when rthi==cand, but
it will also destroy the ordering.
end_of_quotation
Problematic commit is 1080d709fb
(net: implement emergency route cache rebulds when gc_elasticity is exceeded)
Trying to keep dst_entries ordered is too complex and breaks the fact that
order should depend on the frequency of use for garbage collection.
A possible fix is to make rt_intern_hash() simpler, and only makes
rt_check_expire() a litle bit smarter, being able to cope with an arbitrary
entries order. The added loop is running on cache hot data, while cpu
is prefetching next object, so should be unnoticied.
Reported-and-analyzed-by: Alexander V. Lukyanov <lav@yar.ru>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_check_expire() computes average and standard deviation of chain lengths,
but not correclty reset length to 0 at beginning of each chain.
This probably gives overflows for sum2 (and sum) on loaded machines instead
of meaningful results.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now we have no upper limit on the size of the route cache hash table.
On a 128GB POWER6 box it ends up as 32MB:
IP route cache hash table entries: 4194304 (order: 9, 33554432 bytes)
It would be nice to cap this for memory consumption reasons, but a massive
hashtable also causes a significant spike when measuring OS jitter.
With a 32MB hashtable and 4 million entries, rt_worker_func is taking
5 ms to complete. On another system with more memory it's taking 14 ms.
Even though rt_worker_func does call cond_sched() to limit its impact,
in an HPC environment we want to keep all sources of OS jitter to a minimum.
With the patch applied we limit the number of entries to 512k which
can still be overriden by using the rt_entries boot option:
IP route cache hash table entries: 524288 (order: 6, 4194304 bytes)
With this patch rt_worker_func now takes 0.460 ms on the same system.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: build fix
API was changed, but not all usage sites were converted:
net/ipv4/route.c: In function ‘ip_rt_init’:
net/ipv4/route.c:3379: error: too few arguments to function ‘__alloc_percpu’
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Base versions handle constant folding now.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This last patch makes the appropriate changes to use and propagate the
network namespace where needed in IPv4 multicast routing code.
This consists mainly in replacing all the remaining init_net occurences
with current netns pointer retrieved from sockets, net devices or
mfc_caches depending on the routines' contexts.
Some routines receive a new 'struct net' parameter to propagate the current
netns:
* vif_add/vif_delete
* ipmr_new_tunnel
* mroute_clean_tables
* ipmr_cache_find
* ipmr_cache_report
* ipmr_cache_unresolved
* ipmr_mfc_add/ipmr_mfc_delete
* ipmr_get_route
* rt_fill_info (in route.c)
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In future all cpumask ops will only be valid (in general) for bit
numbers < nr_cpu_ids. So use that instead of NR_CPUS in iterators
and other comparisons.
This is always safe: no cpu number can be >= nr_cpu_ids, and
nr_cpu_ids is initialized to NR_CPUS at boot.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass netns to xfrm_lookup()/__xfrm_lookup(). For that pass netns
to flow_cache_lookup() and resolver callback.
Take it from socket or netdevice. Stub DECnet to init_net.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.
So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
call_rcu() will unconditionally rewrite RCU head anyway.
Applies to
struct neigh_parms
struct neigh_table
struct net
struct cipso_v4_doi
struct in_ifaddr
struct in_device
rt->u.dst
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a patch to provide on demand route cache rebuilding. Currently, our
route cache is rebulid periodically regardless of need. This introduced
unneeded periodic latency. This patch offers a better approach. Using code
provided by Eric Dumazet, we compute the standard deviation of the average hash
bucket chain length while running rt_check_expire. Should any given chain
length grow to larger that average plus 4 standard deviations, we trigger an
emergency hash table rebuild for that net namespace. This allows for the common
case in which chains are well behaved and do not grow unevenly to not incur any
latency at all, while those systems (which may be being maliciously attacked),
only rebuild when the attack is detected. This patch take 2 other factors into
account:
1) chains with multiple entries that differ by attributes that do not affect the
hash value are only counted once, so as not to unduly bias system to rebuilding
if features like QOS are heavily used
2) if rebuilding crosses a certain threshold (which is adjustable via the added
sysctl in this patch), route caching is disabled entirely for that net
namespace, since constant rebuilding is less efficient that no caching at all
Tested successfully by me.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Remove CONFIG_KMOD from net/ (towards removing CONFIG_KMOD entirely)
ipv4: Add a missing rcu_assign_pointer() in routing cache.
[netdrvr] ibmtr: PCMCIA IBMTR is ok on 64bit
xen-netfront: Avoid unaligned accesses to IP header
lmc: copy_*_user under spinlock
[netdrvr] myri10ge, ixgbe: remove broken select INTEL_IOATDMA
rt_intern_hash() is doing an update of a RCU guarded hash chain
without using rcu_assign_pointer() or equivalent barrier.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
name and nlen parameters passed to ->strategy hook are unused, remove
them. In general ->strategy hook should know what it's doing, and don't
do something tricky for which, say, pointer to original userspace array
may be needed (name).
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net> [ networking bits ]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ip_route_output() contains a check to make sure that no flows with
non-local source IP addresses are routed. This obviously makes using
such addresses impossible.
This patch introduces a flowi flag which makes omitting this check
possible. The new flag provides a way of handling transparent and
non-transparent connections differently.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: KOVACS Krisztian <hidden@sch.bme.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When scanning route cache hash table, we can avoid taking locks for
empty buckets. Both /proc/net/rt_cache and NETLINK RTM_GETROUTE
interface are taken into account.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net.ipv4.neigh should be a part of skeleton to avoid ordering problems
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let me first state that disabling the route cache hash rebuild
should not be done without extensive analysis on the risk profile
and careful deliberation.
However, there are times when this can be done safely or for
testing. For example, when you have mechanisms for ensuring
that offending parties do not exist in your network.
This patch lets the user disable the rebuild if the interval is
set to zero. This also incidentally fixes a divide-by-zero error
with name-spaces.
In addition, this patch makes the effect of an interval change
immediate rather than it taking effect at the next rebuild as
is currently the case.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dst_metric() with dst_mtu() in net/ipv4/route.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (46 commits)
tcp: MD5: Fix IPv6 signatures
skbuff: add missing kernel-doc for do_not_encrypt
net/ipv4/route.c: fix build error
tcp: MD5: Fix MD5 signatures on certain ACK packets
ipv6: Fix ip6_xmit to send fragments if ipfragok is true
ipvs: Move userspace definitions to include/linux/ip_vs.h
netdev: Fix lockdep warnings in multiqueue configurations.
netfilter: xt_hashlimit: fix race between htable_destroy and htable_gc
netfilter: ipt_recent: fix race between recent_mt_destroy and proc manipulations
netfilter: nf_conntrack_tcp: decrease timeouts while data in unacknowledged
irda: replace __FUNCTION__ with __func__
nsc-ircc: default to dongle type 9 on IBM hardware
bluetooth: add quirks for a few hci_usb devices
hysdn: remove the packed attribute from PofTimStamp_tag
isdn: use the common ascii hex helpers
tg3: adapt tg3 to use reworked PCI PM code
atm: fix direct casts of pointers to u32 in the InterPhase driver
atm: fix const assignment/discard warnings in the ATM networking driver
net: use the common ascii hex helpers
random32: seeding improvement
...
fix:
net/ipv4/route.c: In function 'ip_static_sysctl_init':
net/ipv4/route.c:3225: error: 'ipv4_route_path' undeclared (first use in this function)
net/ipv4/route.c:3225: error: (Each undeclared identifier is reported only once
net/ipv4/route.c:3225: error: for each function it appears in.)
net/ipv4/route.c:3225: error: 'ipv4_route_table' undeclared (first use in this function)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Piss-poor sysctl registration API strikes again, film at 11...
What we really need is _pathname_ required to be present in already
registered table, so that kernel could warn about bad order. That's the
next target for sysctl stuff (and generally saner and more explicit
order of initialization of ipv[46] internals wouldn't hurt either).
For the time being, here are full fixups required by ..._rotable()
stuff; we make per-net sysctl sets descendents of "ro" one and make sure
that sufficient skeleton is there before we start registering per-net
sysctls.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Running recent kernels, and using a particular vpn gateway, I've been
having to edit my mails down to get them accepted by the smtp server.
Git bisect led to commit e84f84f276 -
netns: place rt_genid into struct net. The conversion from a != test
to rt_is_expired() put one negative too many: and now my mail works.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to avoid locking at all in ipv4_sysctl_rtcache_flush by
defining local ctl_table on the stack.
The patch is based on the suggestion from Eric W. Biederman.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst cache is marked as expired on the per/namespace basis by previous
path. Right now we have to implement selective cache shrinking. This
procedure has been ported from older OpenVz codebase.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically, there is no difference to atomic_read internally or pass it as
a parameter as rt_hash is inline.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush delay is used as an external storage for net.ipv4.route.flush sysctl
entry. It is write-only.
The ctl_table->data for this entry is used once. Fix this case to point
to the stack to remove global variable. Do this to avoid additional
variable on struct net in the next patch.
Possible race (as it was before) accessing this local variable is removed
using flush_mutex.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also removes an obsolete check for the unused flag RTCF_MASQ.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the IPsec output function xfrm_output_resume does its
own dst_output call it should always call __ip_local_output
instead of ip_local_output as the latter may invoke dst_output
directly. Otherwise the return values from nf_hook and dst_output
may clash as they both use the value 1 but for different purposes.
When that clash occurs this can cause a packet to be used after
it has been freed which usually leads to a crash. Because the
offending value is only returned from dst_output with qdiscs
such as HTB, this bug is normally not visible.
Thanks to Marco Berizzi for his perseverance in tracking this
down.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are functions to refer to the value of dst->metric[THE_METRIC-1]
directly without use of a inline function "dst_metric" defined in
net/dst.h.
The following patch changes them to use the inline function
consistently.
Signed-off-by: Satoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add struct net_device parameter to ip_rt_frag_needed() and update MTU to
cache entries where ifindex is specified. This is similar to what is
already done in ip_rt_redirect().
Signed-off-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Plan C: we can follow the Al Viro's proposal about %n like in this patch.
The same applies to udp, fib (the /proc/net/route file), rt_cache and
sctp debug. This is minus ~150-200 bytes for each.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comparison in ip_route_input is a hot path, by recoding the C
"and" as bit operations, fewer conditional branches get generated
so the code should be faster. Maybe someday Gcc will be smart
enough to do this?
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No urgency on the rehash interval timer, so mark it as deferrable.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since route hash is a triple, use jhash_3words rather doing the mixing
directly. This should be as fast and give better distribution.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't mark functions that are large as inline, let compiler decide.
Also, use inline rather than __inline__.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an inline net_eq() to compare two namespaces.
Without CONFIG_NET_NS, since no namespace other than &init_net
exists, it is always 1.
We do not need to convert 1) inline vs inline and
2) inline vs &init_net comparisons.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Without CONFIG_NET_NS, no namespace other than &init_net exists,
no need to store net in seq_net_private.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Introduce per-sock inlines: sock_net(), sock_net_set()
and per-inet_timewait_sock inlines: twsk_net(), twsk_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
The route table parameters are set based on system memory and sysctl
values that almost never change. Also the genid only changes every
10 minutes.
RTprint is defined by never used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(Anonymous) unions can help us to avoid ugly casts.
A common cast it the (struct rtable *)skb->dst one.
Defining an union like :
union {
struct dst_entry *dst;
struct rtable *rtable;
};
permits to use skb->rtable in place.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Show routing cache for a particular namespace only.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the other case /proc/net/rt_cache will look inconsistent in respect to
genid.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use proc_create() to make sure that ->proc_fops be setup before gluing
PDE to main tree.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
