cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Using STM32 as guinea pig after Alex's initial positive
test to see if this is something we should encourage
in general and make default behaviour.
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs are split between several banks (A, B, ...) and each bank can have
up to 16 lines. Those GPIOs could be used as interrupt lines thanks to
exti lines. As there are only 16 exti lines, a mux is used to select which
gpio line is connected to which exti line. Mapping is done as follow:
-A0, B0, C0.. -->exti_line_0 (X0 selected by mux_0)
-A1, B1, C1.. -->exti_line_1 (X1 selected by mux_1)
...
This patch adds a protection to avoid overriding on mux_n for exti_line_n.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During power sequence, GPIO hardware registers could be lost if the power
supply is switched off. Each device using pinctrl API is in charge of
managing pins during suspend/resume sequences. But for pins used as gpio or
irq stm32 pinctrl driver has to save the hardware configuration.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not guaranteed that the IRQ controller driver is probed before
the pin controller driver gets probed.
Considering this, check for the irq domain availability during probe
and return EPROBE_DEFER if needed.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Align pins names with names provided in official stm32mp157 datasheet
available on st.com.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A same SoC can be available in several packages. Differences between
packages are only the numbers of available balls. In order not to write
a driver for each new package, same driver (ex: pinctrl-stm32mp157.c) will
be used. This patch introduces the "package" property for each pin. So on a
same driver, it will be possible to indicate on which package the pin is
available. The package information will be got from the device tree.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Return error to the caller when the hwspinlock can't get locked.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
configs is allocated by pinconf_generic_parse_dt_config(),
pinctrl_utils_add_map_configs() duplicates configs so it can and has to
be freed to prevent memory leaks.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a hwspinlock if defined in device tree use it to protect
configuration registers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds mask parameter to define IRQ mux field.
This field could vary depend of IRQ mux selection register.
To avoid backward compatibility, the drivers set
the legacy value by default.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Register a new GPIO bank only if GPIO bank node is enabled. This patch also
adds checks on ranges which are defined only if a bank is registered.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case the exti line is not in line with the bank number (that is the case
when there is an hole between two banks, for example GPIOK and then GPIOZ),
use "st,bank-ioport" DT property to get the right exti line.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-Parent domain of stm32gpio evolves to hierarchy domain
and could have a handle_fasteoi_irq. So an irq_eoi parent callback
is needed for children.
-Replace space by tabulation.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
These configs select MFD_SYSCON, but do not depend on HAS_IOMEM.
Compile testing on architecture without HAS_IOMEM causes "unmet
direct dependencies" in Kconfig phase.
Detected by "make ARCH=score allyesconfig".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- After lengthy discussions and partly due to my ignorance, we have
merged a patch making pinctrl_force_default() and pinctrl_force_sleep()
reprogram the states into the hardware of any hogged pins, even
if they are already in the desired state. This only apply to hogged
pins since groups of pins owned by drivers need to be managed by
each driver, lest they could not do things like runtime PM and
put pins to sleeping state even if the system as a whole is not
in sleep.
New drivers:
- New driver for the Microsemi Ocelot SoC. This is used in ethernet
switches.
- The X-Powers AXP209 GPIO driver was extended to also deal with pin
control and moved over from the GPIO subsystem. This circuit is
a mixed-mode integrated circuit which is part of AllWinner designs.
- New subdriver for the Qualcomm MSM8998 SoC, core of a high end
mobile devices (phones) chipset.
- New subdriver for the ST Microelectronics STM32MP157 MPU and
STM32F769 MCU from the STM32 family.
- New subdriver for the MediaTek MT7622 SoC. This is used for routers,
repeater, gateways and such network infrastructure.
- New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC has
multimedia features and target "smart devices", I guess in-car
entertainment, in-flight entertainment, industrial control panels etc.
General improvements:
- Incremental improvements on the SH-PFC subdrivers for things like
the CAN bus.
- Enable the glitch filter on Baytrail GPIOs used for interrupts.
- Proper handling of pins to GPIO ranges on the Semtec SX150X
- An IRQ setup ordering fix on MCP23S08.
- A good set of janitorial coding style fixes.
-----BEGIN PGP SIGNATURE-----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=gLY/
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.16 kernel cycle.
Like with GPIO it is actually a bit calm this time.
Core changes:
- After lengthy discussions and partly due to my ignorance, we have
merged a patch making pinctrl_force_default() and
pinctrl_force_sleep() reprogram the states into the hardware of any
hogged pins, even if they are already in the desired state.
This only apply to hogged pins since groups of pins owned by
drivers need to be managed by each driver, lest they could not do
things like runtime PM and put pins to sleeping state even if the
system as a whole is not in sleep.
New drivers:
- New driver for the Microsemi Ocelot SoC. This is used in ethernet
switches.
- The X-Powers AXP209 GPIO driver was extended to also deal with pin
control and moved over from the GPIO subsystem. This circuit is a
mixed-mode integrated circuit which is part of AllWinner designs.
- New subdriver for the Qualcomm MSM8998 SoC, core of a high end
mobile devices (phones) chipset.
- New subdriver for the ST Microelectronics STM32MP157 MPU and
STM32F769 MCU from the STM32 family.
- New subdriver for the MediaTek MT7622 SoC. This is used for
routers, repeater, gateways and such network infrastructure.
- New subdriver for the NXP (former Freescale) i.MX 6ULL. This SoC
has multimedia features and target "smart devices", I guess in-car
entertainment, in-flight entertainment, industrial control panels
etc.
General improvements:
- Incremental improvements on the SH-PFC subdrivers for things like
the CAN bus.
- Enable the glitch filter on Baytrail GPIOs used for interrupts.
- Proper handling of pins to GPIO ranges on the Semtec SX150X
- An IRQ setup ordering fix on MCP23S08.
- A good set of janitorial coding style fixes"
* tag 'pinctrl-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (102 commits)
pinctrl: mcp23s08: fix irq setup order
pinctrl: Forward declare struct device
pinctrl: sunxi: Use of_clk_get_parent_count() instead of open coding
pinctrl: stm32: add STM32F769 MCU support
pinctrl: sx150x: Add a static gpio/pinctrl pin range mapping
pinctrl: sx150x: Register pinctrl before adding the gpiochip
pinctrl: sx150x: Unregister the pinctrl on release
pinctrl: ingenic: Remove redundant dev_err call in ingenic_pinctrl_probe()
pinctrl: sprd: Use seq_putc() in sprd_pinconf_group_dbg_show()
pinctrl: pinmux: Use seq_putc() in pinmux_pins_show()
pinctrl: abx500: Use seq_putc() in abx500_gpio_dbg_show()
pinctrl: mediatek: mt7622: align error handling of mtk_hw_get_value call
pinctrl: mediatek: mt7622: fix potential uninitialized value being returned
pinctrl: uniphier: refactor drive strength get/set functions
pinctrl: imx7ulp: constify struct imx_cfg_params_decode
pinctrl: imx: constify struct imx_pinctrl_soc_info
pinctrl: imx7d: simplify imx7d_pinctrl_probe
pinctrl: imx: use struct imx_pinctrl_soc_info as a const
pinctrl: sunxi-pinctrl: fix pin funtion can not be match correctly.
pinctrl: qcom: Add msm8998 pinctrl driver
...
The 'early' argument of irq_domain_activate_irq() is actually used to
denote reservation mode. To avoid confusion, rename it before abuse
happens.
No functional change.
Fixes: 7249164346 ("genirq/irqdomain: Update irq_domain_ops.activate() signature")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexandru Chirvasitu <achirvasub@gmail.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Mikael Pettersson <mikpelinux@gmail.com>
Cc: Josh Poulson <jopoulso@microsoft.com>
Cc: Mihai Costache <v-micos@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-pci@vger.kernel.org
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Simon Xiao <sixiao@microsoft.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jork Loeser <Jork.Loeser@microsoft.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: devel@linuxdriverproject.org
Cc: KY Srinivasan <kys@microsoft.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sakari Ailus <sakari.ailus@intel.com>,
Cc: linux-media@vger.kernel.org
This driver consists of 2 controllers due to a hole in mapping:
-1 controller for GPIO bankA to K.
-1 controller for GPIO bankZ.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into
a menuconfig option. This obviously has the implication of
making the subsystem menu visible in menuconfig. This is
happening because of two things:
- Intel have started to deploy and depend on pin controllers
in a way that is affecting users directly. This happens
on the highly integrated laptop chipsets named after
geographical places: baytrail, broxton, cannonlake,
cedarfork, cherryview, denverton, geminilake, lewisburg,
merrifield, sunrisepoint... It started a while back and
now it is ever more evident that this is crucial
infrastructure for x86 laptops and not an embedded
obscurity anymore. Users need to be aware.
- Pin control expanders on I2C and SPI that are
arch-agnostic. Currently Semtech SX150X and Microchip
MCP28x08 but more are expected. Users will have to be
able to configure these in directly for their set-up.
- Just go and select GPIOLIB now that we made sure that
GPIOLIB is a very vanilla subsystem. Do not depend on
it, if we need it, select it.
- Exposing the pin control subsystem in menuconfig uncovered
a bunch of obscure bugs that are now hopefully fixed,
all more or less pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and
GPIO.
- New support for clock skew/delay generic DT bindings
and generic pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJaDV9TAAoJEEEQszewGV1zf0AQAIlHxM8B0mJPOFv7WdPIHs8j
GSGAPv0rPobdgZI8vegosIQmAiry5jjaHP6VGOrK5n8FRxfBLd89NLT7dgK7J9Yx
tYcQRQn1/MqZKaIjWWgTes3okEr9s77Of3aWkA9gyvBjTGoo2hu8BTwZOYuPrIPP
aYcI7VR0VbTe7FQR1QRtKBXnBTXfznF1j5ckKNY4ahgIPcUgxyh6EA1E61rDorLK
gvwwzoBqIKQAcnapgarF7YOJjoE0i7ZoSlhL0b0nvhcgolyK/zLN4xujLcTGPeTJ
hQwe7LhxtvtmJmu0jRMuetDLFT52d6eq8ttyFBMULkgRzcgMv6GZZXUy4k92t7ZT
F2DRbAjyAlxkhUhQ8BORzEXwfWYITt1M49jWQqugdDR2fV/MAlF8motOkVBl73iS
zHIQ/ZDcAD+PlwTHiDyDOUxj7qyDs2MkTLTzfXc0koOQZOqskDHQ1dIf3UzLzZ9S
/dx339/ejwP73E0lzOsanhianfonqWZ3Apn3aRG18uqCt2+eHySWpxyRANuOlBZI
czERg+47wDfng24xyuH0EElgbS5G0Bt1lT5zLVLdFEvoLmcBHVKqaCkiuvYXOjVM
GyMRvQPiJbhT6qiJ+aSP8t/utl1aUhXQLtrUnXxu8qv9tQ6jgmqiQd9855Uvrzb0
ZR2wyNc2jtWzwCfrkWjt
=kj/b
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers that need IRQ_DOMAIN_HIERARCHY should "select" it, but
drivers/pinctrl/stm32/Kconfig is the only exception that uses
"depends on" syntax. This prevents GPIO drivers from select'ing
IRQ_DOMAIN_HIERARCHY.
For example, if I add "select IRQ_DOMAIN_HIERARCHY" to GPIO_XGENE_SB,
I get the following recursive dependency error.
drivers/gpio/Kconfig:13:error: recursive dependency detected!
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:13: symbol GPIOLIB is selected by PINCTRL_STM32
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:3: symbol PINCTRL_STM32 is selected by PINCTRL_STM32F429
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:11: symbol PINCTRL_STM32F429 depends on IRQ_DOMAIN_HIERARCHY
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
kernel/irq/Kconfig:67: symbol IRQ_DOMAIN_HIERARCHY is selected by GPIO_XGENE_SB
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:502: symbol GPIO_XGENE_SB depends on GPIOLIB
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In stm32_pconf_parse_conf function, stm32_pmx_gpio_set_direction is
called with wrong parameter value. Indeed, using NULL value for range
will raise an oops.
Fixes: aceb16dc2d ("pinctrl: Add STM32 MCUs support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no link between the number of elements of tab which contains all
pin desc (located in each pinctrl-stm32xxxx.c files) and the pin number
(defined in the tab).
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch ensures that pin is correctly set as gpio input when it is used
as an interrupt.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch which adds STM32F469 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pinctrl has to be registered earlier. Mainly to register bank irqdomain
earlier as other devices could use interrupts from those irqdomain.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device tree entries to declare gpio range. It will allow to use
no contiguous gpio bank and holes inside a bank.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move gpio lock as irq from "domain alloc" callback to "domain activate"
callback. It will allow to use gpiolib sysfs correctly.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This activates strict mode muxing for the STM32 pin controllers,
as these do not allow GPIO and functions to use the same pin
simultaneously.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and
reimagined as a pin control driver with GPIO support
in a joint effort by three independent users of this
hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control
bindings rather than the sunxi-specific. Add debouncing
support to the driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over
to use the generic GPIOLIB_IRQCHIP.
-----BEGIN PGP SIGNATURE-----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=Pkzu
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl updates from Linus Walleij:
"Bulk pin control changes for the v4.10 kernel cycle:
No core changes this time. Mainly gradual improvement and
feature growth in the drivers.
New drivers:
- New driver for TI DA850/OMAP-L138/AM18XX pinconf
- The SX150x was moved over from the GPIO subsystem and reimagined as
a pin control driver with GPIO support in a joint effort by three
independent users of this hardware. The result was amazingly good!
- New subdriver for the Oxnas OX820
Improvements:
- The sunxi driver now supports the generic pin control bindings
rather than the sunxi-specific. Add debouncing support to the
driver.
- Simplifications in pinctrl-single adding a generic parser.
- Two downstream fixes and move the Raspberry Pi BCM2835 over to use
the generic GPIOLIB_IRQCHIP"
* tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (92 commits)
pinctrl: sx150x: use new nested IRQ infrastructure
pinctrl: sx150x: handle missing 'advanced' reg in sx1504 and sx1505
pinctrl: sx150x: rename 'reg_advance' to 'reg_advanced'
pinctrl: sx150x: access the correct bits in the 4-bit regs of sx150[147]
pinctrl: mt8173: set GPIO16 to usb iddig mode
pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP
pinctrl: New driver for TI DA850/OMAP-L138/AM18XX pinconf
devicetree: bindings: pinctrl: Add binding for ti,da850-pupd
Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition
pinctrl: intel: set default handler to be handle_bad_irq()
pinctrl: sx150x: add support for sx1501, sx1504, sx1505 and sx1507
pinctrl: sx150x: sort chips by part number
pinctrl: sx150x: use correct registers for reg_sense (sx1502 and sx1508)
pinctrl: imx: fix imx_pinctrl_desc initialization
pinctrl: sx150x: support setting multiple pins at once
pinctrl: sx150x: various spelling fixes and some white-space cleanup
pinctrl: mediatek: use builtin_platform_driver
pinctrl: stm32: use builtin_platform_driver
pinctrl: sunxi: Testing the wrong variable
pinctrl: nomadik: split up and comments MC0 pins
...
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch allows to probe stm32 pinctrl driver even if no interrupt
controller is defined to manage gpio irqs.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The newly added irqchip support for the stm32 pinctrl driver uses
hierarchical IRQ domains as provided by the NVIC primary irqchip.
This works great for any configuration that may be relevant on
stm32, but when doing compile-testing (randconfig), we can
enable it without NVIC or any other primary irqchip that
enables IRQ_DOMAIN_HIERARCHY:
drivers/pinctrl/stm32/pinctrl-stm32.c:212:13: error: 'irq_chip_eoi_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:213:20: error: 'irq_chip_mask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:214:20: error: 'irq_chip_unmask_parent' undeclared here (not in a function)
drivers/pinctrl/stm32/pinctrl-stm32.c:215:20: error: 'irq_chip_set_type_parent' undeclared here (not in a function)
This adds a Kconfig dependency to limit compile-testing to
configurations that have IRQ_DOMAIN_HIERARCHY already enabled.
It's not obvious whether we should use 'depends on' or 'select'
here, I think either one works, with 'depends on' being more
intuitive, while 'select' would be less likely to cause dependency
loops.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0eb9f68333 ("pinctrl: Add IRQ support to STM32 gpios")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only used to copy into other structures, so declare
them as const.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds IRQ support to STM32 gpios.
The EXTI controller has 16 lines dedicated to GPIOs.
EXTI line n can be connected to only line n of one of the GPIO ports, for
example EXTI0 can be connected to either PA0, or PB0, or PC0...
This port selection is done by specifying the port number into System
Config registers.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch which adds STM32F746 pinctrl and GPIO support, relies on the
generic STM32 pinctrl driver.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
