Current dts files with 'gpio-led' nodes were manually verified.
In order to automate this process leds-gpio.txt
has been converted to yaml. With this conversion a check
for pattern properties was added. A test with the command
below gives a screen full of warnings like:
arch/arm64/boot/dts/rockchip/rk3368-r88.dt.yaml: gpio-leds:
'work' does not match any of the regexes:
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Fix these errors with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
patternProperties:
# The first form is preferred, but fall back to just 'led'
# anywhere in the node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/leds/
leds-gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200428144933.10953-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable SPI1 exposed on both Low and High speed expansion connectors
of Ficus. SPI1 has 3 different chip selects wired as below:
CS0 - Serial Flash (unpopulated)
CS1 - Low Speed expansion
CS2 - High Speed expansion
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add on-board LED support for Ficus board based on the following
standard used by other 96Boards:
red:user1 default-trigger: heartbeat
red:user2 default-trigger: mmc0/disk-activity (onboard-storage)
red:user3 default-trigger: mmc1 (SD-card)
red:user4 default-trigger: none, panic-indicator
red:wlan default-trigger: phy0tx
red:bt default-trigger: hci0-power
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Since the same family members of Rock960 boards (Rock960 and Ficus)
share the same configuration, split out the common nodes into a common
dtsi file for reducing code duplication. The board specific nodes for
Ficus boards are then placed in corresponding board DTS file.
Below are some of the key differences between both Rock960 and Ficus
boards:
1. Different host enable GPIO for USB
2. Different power and reset GPIO for PCI-E
3. No Ethernet port on Rock960
Only the properties which differ between both boards are placed in the
board specific dts and the reset of the nodes are placed in common dtsi
file.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The pwm-regulator for vdd_log uses additional unreviewed properties in the
vendor kernel, which slipped in with the devicetree.
As written, they are unreviewed and unused in all mainline implementations
so drop them again.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The vcc3v3_pcie regulator supplies 3.3V so add voltage properties
for it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
[split off from original patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The board exposes two types A ports, one is USB 3.0, up to 5.0Gbps and
another one is USB 2.0 up to 480Mbps. Enable the USB PHYs and the USB
controllers to enable theses devices.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The RK3399 Ficus board is an Enterprise Edition board
manufactured by Vamrs Ltd., based on the Rockchip RK3399 SoC.
The board exposes a bunch of nice peripherals, including
SATA, HDMI, MIPI CSI, Ethernet, WiFi, and PCIe.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
