This reverts commit ae0e8e8220.
This change had two problems:
1) Since it frees the stats in the drivers' close method, we
can OOPS in the transmit routine.
2) stats are no longer remembered across ifdown/ifup which
disagrees with how every other device operates.
Thanks to analysis and test patch from Serge E. Hallyn
and initial OOPS report by Sachin Sant.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes and obvious typo in the netdev_ops initialization:
ndo_so_ioctl should be ndo_do_ioctl.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6:
bnx2: Fix the behavior of ethtool when ONBOOT=no
qla3xxx: Don't sleep while holding lock.
qla3xxx: Give the PHY time to come out of reset.
ipv4 routing: Ensure that route cache entries are usable and reclaimable with caching is off
net: Move rx skb_orphan call to where needed
ipv6: Use correct data types for ICMPv6 type and code
net: let KS8842 driver depend on HAS_IOMEM
can: let SJA1000 driver depend on HAS_IOMEM
netxen: fix firmware init handshake
netxen: fix build with without CONFIG_PM
netfilter: xt_rateest: fix comparison with self
netfilter: xt_quota: fix incomplete initialization
netfilter: nf_log: fix direct userspace memory access in proc handler
netfilter: fix some sparse endianess warnings
netfilter: nf_conntrack: fix conntrack lookup race
netfilter: nf_conntrack: fix confirmation race condition
netfilter: nf_conntrack: death_by_timeout() fix
I found a little bug.
When configure in ifcfg-eth* is ONBOOT=no,
the behavior of ethtool command is wrong.
# grep ONBOOT /etc/sysconfig/network-scripts/ifcfg-eth2
ONBOOT=no
# ethtool eth2 | tail -n1
Link detected: yes
I think "Link detected" should be "no".
Signed-off-by: Ooiwa Naohiro <nooiwa@miraclelinux.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA: Add __init/__exit macros to addr.c and cma.c
IB/ehca: Bump version number
mlx4_core: Fix dma_sync_single_for_cpu() with matching for_device() calls
IB/mthca: Replace dma_sync_single() use with proper functions
RDMA/nes: Fix FIN state handling under error conditions
RDMA/nes: Fix max_qp_init_rd_atom returned from query device
IB/ehca: Ensure that guid_entry index is not negative
IB/ehca: Tolerate dynamic memory operations before driver load
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (38 commits)
fusion: mptsas, fix lock imbalance
[SCSI] scsi_transport_fc: replace BUS_ID_SIZE by fixed count
sd, sr: fix Driver 'sd' needs updating message
scsi_transport_iscsi: return -EOVERFLOW for Too many iscsi targets
fc_transport: Selective return value from BSG timeout function
fc_transport: The softirq_done function registration for BSG request
sym53c8xx: ratelimit parity errors
explain the hidden scsi_wait_scan Kconfig variable
ibmvfc: Fix endless PRLI loop in discovery
ibmvfc: Process async events before command responses
libfc: Add runtime debugging with debug_logging module parameter
libfcoe: Add runtime debugging with module param debug_logging
fcoe: Add runtime debug logging with module parameter debug_logging
scsi_debug: Add support for physical block exponent and alignment
cnic: add NETDEV_1000 and NETDEVICES to Kconfig select
cnic: Fix __symbol_get() build error.
Revert "[SCSI] cnic: fix error: implicit declaration of function ‘__symbol_get’"
ipr: differentiate pci-x and pci-e based adapters
ipr: add test for MSI interrupt support
scsi_transport_spi: Blacklist Ultrium-3 tape for IU transfers
...
Fixes this compile error on s390:
CC drivers/net/ks8842.o
drivers/net/ks8842.c: In function 'ks8842_select_bank':
drivers/net/ks8842.c:124: error: implicit declaration of function 'iowrite16'
drivers/net/ks8842.c: In function 'ks8842_write8':
drivers/net/ks8842.c:131: error: implicit declaration of function 'iowrite8'
Cc: Richard Rojfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes this compile error on s390:
drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_read_reg':
drivers/net/can/sja1000/sja1000_platform.c:42: error: implicit declaration of function 'ioread8'
drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_write_reg':
drivers/net/can/sja1000/sja1000_platform.c:47: error: implicit declaration of function 'iowrite8'
drivers/net/can/sja1000/sja1000_platform.c: In function 'sp_probe':
drivers/net/can/sja1000/sja1000_platform.c:79: error: implicit declaration of function 'ioremap_nocache'
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Oliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure all functions run firmware init handshake.
If PCI function 0 fails to initialize firmware, mark the
state failed so that other functions on the same board
bail out quickly instead of waiting 30s for firmware
handshake.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wrap pci suspend() and resume() with CONFIG_PM check.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5d23a1d2 ("net: replace dma_sync_single with
dma_sync_single_for_cpu") replaced uses of the deprectated function
dma_sync_single() with calls to dma_sync_single_for_cpu(). However,
to be correct, the code should do a sync for_cpu() before touching the
memory and for_device() after it's done.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (43 commits)
via-velocity: Fix velocity driver unmapping incorrect size.
mlx4_en: Remove redundant refill code on RX
mlx4_en: Removed redundant check on lso header size
mlx4_en: Cancel port_up check in transmit function
mlx4_en: using stop/start_all_queues
mlx4_en: Removed redundant skb->len check
mlx4_en: Counting all the dropped packets on the TX side
usbnet cdc_subset: fix issues talking to PXA gadgets
Net: qla3xxx, remove sleeping in atomic
ipv4: fix NULL pointer + success return in route lookup path
isdn: clean up documentation index
cfg80211: validate station settings
cfg80211: allow setting station parameters in mesh
cfg80211: allow adding/deleting stations on mesh
ath5k: fix beacon_int handling
MAINTAINERS: Fix Atheros pattern paths
ath9k: restore PS mode, before we put the chip into FULL SLEEP state.
ath9k: wait for beacon frame along with CAB
acer-wmi: fix rfkill conversion
ath5k: avoid PCI FATAL interrupts by restoring RETRY_TIMEOUT disabling
...
The ppp layer goes around calling the unthrottle method from non sleeping
paths. This isn't safe because the unthrottle methods in the tty layer need
to be able to sleep (consider a USB dongle).
Until now this didn't show up because the ppp layer never actually throttled
a port so the unthrottle was always a no-op. Currently it's a mutex taking
path so warnings are spewed if the unthrottle occurs via certain paths.
Fix this by removing the unneccessary unthrottle calls.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The s6000 on-chip MAC supports 10/100/1000Mbit and is connected to an
external PHY via MII or RGMII interface.
[jw@emlix.com: don't use device->bus_id directly]
Signed-off-by: Oskar Schirmer <os@emlix.com>
Signed-off-by: Daniel Glockner <dg@emlix.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Johannes Weiner <jw@emlix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Zankel <chris@zankel.net>
When a packet is greater than ETH_ZLEN, we end up assigning the
boolean result of a comparison to the size we unmap.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our RX rings are always full, there is no need to check whether
we need to fill them or not. If we fail to allocate a new socket
buffer, the incoming packet is dropped an the ring remains full.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This check that verifies that the LSO header along with control
segment and first data segment do not cross 128 bytes is no longer
required.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When closing the port, we stop all transmit queues under the transmit
lock. It ensures that we will not attempt to transmit new packets after
the physical port was closed.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
After we moved to be a multi queue device, need to stop/start
all of our transmit queues.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need this check in the transmit function
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reporting the counter's value through 'ethtool -S'
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ingo molnar <mingo@elte.hu> reported the error
drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’
when CONFIG_MODULES is not defined. Fix by using symbol_get() instead.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts commit bc3bf8fd33.
All the commit did was add a second #include of <linux/module.h> which is
the wrong fix.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The host-side CDC subset driver is binding more specifically
than it should ... only to PXA 210/25x/26x Linux-USB gadgets.
Loosen that restriction to match the gadget driver driver.
This will various PXA 27x and PXA 3xx devices happier when
talking to Linux hosts, potentially others.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tested-by: Aric D. Blumer <aric@sdgsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot sleep in ql_reset_work under spinlock, unlock before sleep,
relock after.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to make DMA_nnBIT_MASK() emit `deprecated' warnings. Convert the
remaining stragglers which are visible to the x86_64 build.
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsil.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Yi Zou <yi.zou@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
73ca520336
(ath5k: remove conf->beacon_int usage)
removed bintval setting from ath5k_config. We need to init the
interval earlier and don't touch it in add_interface anymore.
Otherwise it will be set only once by upper layer through
bss_info_changed but not on second and further hostap executions.
We ended up having bintval 1000 which rendered the AP useless on
many clients.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We want to put the chip into FULL SLEEP state, when we are disabling the
radio, but the the current code always change it to AWAKE/NETWORK SLEEP.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts 'ath5k: remove dummy PCI "retry timeout" fix' on the
same theory as in 'ath9k: Fix PCI FATAL interrupts by restoring
RETRY_TIMEOUT disabling'.
Reported-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An earlier commit, 'ath9k: remove dummy PCI "retry timeout" fix', removed
code that was documented to disable RETRY_TIMEOUT register (PCI reg
0x41) since it was claimed to be a no-op. However, it turns out that
there are some combinations of hosts and ath9k-supported cards for
which this is not a no-op (reg 0x41 has value 0x80, not 0) and this
code (or something similar) is needed. In such cases, the driver may
be next to unusable due to very frequent PCI FATAL interrupts from the
card.
Reverting the earlier commit, i.e., restoring the RETRY_TIMEOUT
disabling, seems to resolve the issue. Since the removal of this code
was not based on any known issue and was purely a cleanup change, the
safest option here is to just revert that commit. Should there be
desire to clean this up in the future, the change will need to be
tested with a more complete coverage of cards and host systems.
http://bugzilla.kernel.org/show_bug.cgi?id=13483
Cc: stable@kernel.org
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hans Pontar reported success on the sourceforge zd1211-devs mailing list.
The device is branded "Arcor Easy Stick A 50 WLAN" (device manufactured
by SMC for a German ISP - SMC model name: WN4501H-LF-IR). General
information and Windows driver are available under (German only):
http://www.arcor.de/hilfe/neu/index.php?sid=&aktion=anzeigen&rubrik=004018140&id=487
Device details:
USB-IDs: Vendor: 0x083A Device: 0xE503
Chip ID: zd1211b chip 083a:e503 v4810 high 00-1d-19 AL2230S_RF pa0 g--N-
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Tested-by: Hans Pontar <pontar@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch adds a mutex to protect the iwm_reset_worker against netdev
ndo_open and ndo_stop because all of them call iwm_up and iwm_down in
the implementation. Note the latter two are already protected by
rtnl. So if iwm_reset_worker is not required in the future, the mutex
can also be removed.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwm_if_free() is called before destroy_workqueue for isr_wq on
device remove method. But if there is still some pending work in
the isr_wq, the required data structures are already freed at this
point. This leeds a kernel oops. The patch fixes this problem by
moving iwm_if_free after destroy_workqueue.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We used to do alloc_netdev and register_netdev at the same time in
iwm_if_alloc. But some bus related structures will only be initialized
after iwm_priv is allocated. This caused a race condition that the
netdev might be registered earlier. The patch adds iwm_if_add and
iwm_if_remove so that the bus layer could register the device after
all initialization is done.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to check for iwm_priv_init() errors and do proper cleanups.
Otherwise we may fail to catch the create_singlethread_workqueue()
error which will cause a kernel oops when destroy_workqueue() later.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Unicast Promiscious Mode (UPM) bit in the mv643xx_eth port
configuration register doesn't do exactly what its name would suggest:
setting this bit merely enables reception of all unicast frames with a
destination address that differs from our local MAC address in bits
[47:4]. In particular, it doesn't have any effect on unicast frames
with a destination address that matches our MAC address in bits [47:4]
-- these will still be tested against the 16-entry unicast address
filter table.
Therefore, if the interface is set to promiscuous mode, just setting
the unicast promiscuous bit isn't enough -- we need to set all filter
bits in the unicast filter table to 1 as well.
Reported-by: Sachin Sanap <ssanap@marvell.com>
Signed-off-by: Prabhanjan Sarnaik <sarnaik@marvell.com>
Tested-by: Siddarth Gore <gores@marvell.com>
Tested-by: Mahavir Jain <mjain@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
all references got removed by 865c652d6b
(r8169: remove non-napi code).
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last hunk of this commit:
commit 12d04a3c12
Author: Alexander Duyck <alexander.h.duyck@intel.com>
Date: Wed Mar 25 22:05:03 2009 +0000
e1000e: commonize tx cleanup routine to match e1000 & igb
changed the logic for determining if we should call napi_complete or
not at then end of a napi poll.
If the NIC is using MSI-X with no work to do in ->poll, net_rx_action
can just spin indefinitely on older kernels and for 2 jiffies on newer
kernels since napi_complete is never called and budget isn't
decremented.
Discovered and verified while testing driver backport to an older
kernel.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds five PID's to the whitelist set of devices.
Devices added to the whitelist:
Dell Wireless 5530 HSPA
Ericsson Mobile Broadband Module variants (F3507g, F3607gw and F3307)
Toshiba F3507g
Signed-off-by: Jonas Sjöquist <jonas.sjoquist@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rcv and process ansync link status notifications from BE instead of polling
for link status in the be_worker thread.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup multicast_set method to avoid an extra copy of mc_list
and unwanted promiscuos sets to BE.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currenlty multicast_set and promiscuous_config cmds -- that may be called in BH context --
use the blocking MCC mbox to post cmds.
An mbox cmd is protected via a spin_lock(cmd_lock) and not spin_lock_bh() as it is undesirable
to disable BHs while a blocking mbox cmd is in progress (and take long to finish.)
This can lockup a cmd in progress in process context.
So, these two cmds in BH context must use the MCC queue to post cmds.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currenlty all cmds use the blocking MCC mbox to post cmds. An mbox cmd is protected
via a spin_lock(cmd_lock) and not spin_lock_bh() as it is undesirable
to disable BHs while a blocking mbox cmd is in progress (and take long to finish.)
This can lockup a cmd in progress in process context. Instead cmds that may be
called in BH context must use the MCC queue to post cmds. The cmd completions
are rcvd in a separate completion queue and the events are placed in the tx-event
queue.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes various endianness bugs. Some harmless and some real ones.
This is tested on a PowerPC-64 machine.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
This forces every update of tx ring producer to check for
availability of space for next full TSO command. Earlier
firmware control commands didn't care to pause tx queue.
Stop the tx queue if there's not enough space to transmit one full
LSO command left on the tx ring after current transmit. This avoids
returning NETDEV_TX_BUSY after checking distance between producer
and consumer on every cpu.
Restart the tx queue only if we have cleaned up enough tx
descriptors.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the detection of cut-thru mode of the hardware (direct dma
to host) to mode configured in SRE (ingress block) rather than
onboard memory control.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
forcedeth doesnt use properly dma api in its tx completion path
and in nv_loopback_test()
pci_map_single() should be paired with pci_unmap_single()
pci_map_page() should be paired with pci_unmap_page()
forcedeth xmit path uses pci_map_single() & pci_map_page(),
but tx completion path only uses pci_unmap_single()
nv_loopback_test() uses pci_map_single() & pci_unmap_page()
Add a dma_single field in struct nv_skb_map, and
define a helper function nv_unmap_txskb
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the adapter is not power-manageable using either ACPI, or the
native PCI PM interface, __e100_power_off() returns error code, which
causes every attempt to suspend to fail, although it should return 0
in such a case. Fix this problem by ignoring the return value of
pci_set_power_state() in __e100_power_off().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_disable was called twice in the remove function.
Correct this so that the driver module unloads without error.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements skb recycling. It reclaims transmitted skb's
for use in the receive ring.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the size of the driver transmit ring to reduce latency
and allow qdisc to do better rate control. Also make it
obvious what the minimum transmit ring allowed is and why.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it is likely that there are multiple packets received per
interrupt, only update the receive counters once after all
packets are processed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logic in sky2_down was incorrect. Receiver could report status
after rx_stop was called.
The steps need to be:
* stop new frames from being transmitted
* shut off transmit/receive logic
* synchronize with NAPI to process status info about transmitter
and receiver
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some read's to avoid any PCI posting issues when controlling
irq's.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset more parts of the receive path when device is take offline.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unblocks the chip if it is stuck in pause cycle during
shutdown.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stopping all activity through ChipCmd and blindly acking the irqs
is neither nice nor completely needed: the transition to low-power
mode does enough work and it apparently keeps the device in a sane
state.
Patch suggested by a fix for http://bugzilla.kernel.org/show_bug.cgi?id=9512
The rtl_shutdown path is kept unchanged so far.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Anders Eriksson <aeriksson@fastmail.fm>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sis190 driver is trying to get default phy, if it doesn't find home
or lan phy, it falls back to the first phy in the phy list but list_entry()
points to a bogus entry. list_first_entry() should be used instead.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-- derived from reverted commit 047584ce94
-- reworked by Grant Likely to play nice with commit:
"net: Rework ucc_geth driver to use of_mdio infrastructure"
(0b9da337dc)
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 047584ce94.
This patch meshes badly with "net: Rework ucc_geth driver to use
of_mdio infrastructure" (0b9da337dc).
Since most of the patch needs to be reworked, it is clearer to revert
the patch and then apply the corrected version
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] aic79xx: make driver respect nvram for IU and QAS settings
[SCSI] don't attach ULD to Dell Universal Xport
[SCSI] lpfc 8.3.3 : Update driver version to 8.3.3
[SCSI] lpfc 8.3.3 : Add support for Target Reset handler entrypoint
[SCSI] lpfc 8.3.3 : Fix a couple of spin_lock and memory issues and a crash
[SCSI] lpfc 8.3.3 : FC/FCOE discovery fixes
[SCSI] lpfc 8.3.3 : Fix various SLI-3 vs SLI-4 differences
[SCSI] qla2xxx: Resolve a performance issue in interrupt
[SCSI] cnic, bnx2i: Fix build failure when CONFIG_PCI is not set.
[SCSI] nsp_cs: time_out reaches -1
[SCSI] qla2xxx: fix printk format warnings
[SCSI] ncr53c8xx: div reaches -1
[SCSI] compat: don't perform unneeded copy in sg_io code
[SCSI] zfcp: Update FC pass-through support
[SCSI] zfcp: Add FC pass-through support
[SCSI] FC Pass Thru support
Fix kernel-doc parameter name in phy_device.c.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up remaining drivers returning a magic or an errno value from their
ndo_start_xmit() functions that were missed in the first pass:
- isdn_net: missed conversion
- bpqether: missed conversion: skb is freed, so return NETDEV_TX_OK
- hp100: intention appears to be to resubmit skb once resources are
available, but due to no queue handling it is dropped for now.
- lapbether: skb is freed, so return NETDEV_TX_OK
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Enabled SRIOV support in the driver.
- Call __vxge_hw_verify_pci_e_info() for the PF only. This function
verifies the negotiated link width and current link speed in the
Link Status Register (offset 12h) which are reserved fields for VFs
as per the SRIOV specification, section 3.5.8.
- Implemented David Miller's comment to remove the #ifdef CONFIG_PCI_IOV as
these intefaces have NOP versions declared when the defintion is not set.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Rastapur Santosh <santosh.rastapur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (64 commits)
debugfs: use specified mode to possibly mark files read/write only
debugfs: Fix terminology inconsistency of dir name to mount debugfs filesystem.
xen: remove driver_data direct access of struct device from more drivers
usb: gadget: at91_udc: remove driver_data direct access of struct device
uml: remove driver_data direct access of struct device
block/ps3: remove driver_data direct access of struct device
s390: remove driver_data direct access of struct device
parport: remove driver_data direct access of struct device
parisc: remove driver_data direct access of struct device
of_serial: remove driver_data direct access of struct device
mips: remove driver_data direct access of struct device
ipmi: remove driver_data direct access of struct device
infiniband: ehca: remove driver_data direct access of struct device
ibmvscsi: gadget: at91_udc: remove driver_data direct access of struct device
hvcs: remove driver_data direct access of struct device
xen block: remove driver_data direct access of struct device
thermal: remove driver_data direct access of struct device
scsi: remove driver_data direct access of struct device
pcmcia: remove driver_data direct access of struct device
PCIE: remove driver_data direct access of struct device
...
Manually fix up trivial conflicts due to different direct driver_data
direct access fixups in drivers/block/{ps3disk.c,ps3vram.c}
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (38 commits)
ps3flash: Always read chunks of 256 KiB, and cache them
ps3flash: Cache the last accessed FLASH chunk
ps3: Replace direct file operations by callback
ps3: Switch ps3_os_area_[gs]et_rtc_diff to EXPORT_SYMBOL_GPL()
ps3: Correct debug message in dma_ioc0_map_pages()
drivers/ps3: Add missing annotations
ps3fb: Use ps3_system_bus_[gs]et_drvdata() instead of direct access
ps3flash: Use ps3_system_bus_[gs]et_drvdata() instead of direct access
ps3: shorten ps3_system_bus_[gs]et_driver_data to ps3_system_bus_[gs]et_drvdata
ps3: Use dev_[gs]et_drvdata() instead of direct access for system bus devices
block/ps3: remove driver_data direct access of struct device
ps3vram: Make ps3vram_priv.reports a void *
ps3vram: Remove no longer used ps3vram_priv.ddr_base
ps3vram: Replace mutex by spinlock + bio_list
block: Add bio_list_peek()
powerpc: Use generic atomic64_t implementation on 32-bit processors
lib: Provide generic atomic64_t implementation
powerpc: Add compiler memory barrier to mtmsr macro
powerpc/iseries: Mark signal_vsp_instruction() as maybe unused
powerpc/iseries: Fix unused function warning in iSeries DT code
...
The code to compute VPD size didn't handle some systems that use
chip without VPD. Also some of the newer chips use some additional
registers to store the actual size, and wasn't worth putting the
additional complexity in, so just remove the code.
No big loss since the code to set the VPD size was only a
convenience so that utilities would not read the extra space past
the end of the available VPD.
Move the first PCI config read earlier to detect bad hardware
where it returns all ones and refuse loading driver before furthur
damage.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.
And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.
debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/
Fix inconsistency of directory name to mount debugfs filesystem.
* From Steven Rostedt
- find_debugfs() and tracing_files() in this patch.
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.osdl.org
Acked-by: Chris Wright <chrisw@sous-sol.org>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for misc devices to report their requested nodename to
userspace. It also updates a number of misc drivers to provide the
needed subdirectory and device name to be used for them.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch eplaces the shared FIRMWARE_NAME_MAX definition with a libertas
local one.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
probe functions should be __devinit
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we are in PS mode, we have to process the received frame if
the SC_OP_WAIT_FOR_CAB bit is set.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have to remain awake if the SC_OP_WAIT_FOR_CAB flag is set.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k_ps_{wakeup,restore} calls must be in balance.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ports the ath9k rfkill code to the new API offered by
cfg80211 and thus removes a lot of useless stuff.
("With this series a kernel panic, which is a regression, during module
unload disappears." -- Vasanthakumar Thiagarajan <vasanth@atheros.com>
Other patches in the series:
ath9k: Add helper to get ath9k specific current channel
ath9k: Make sure we have current channel in ah_curchan before rf
disable/enable
-- JWL)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis Rodriguez <mcgrof@gmail.com>
Tested-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is from Nick Kossifidis but he forgot to send it. It ensures
that the beacon queue gets started in mesh mode as well, otherwise ath5k
will not beacon in mesh point mode.
At this time, we still need to issue a scan before mesh beaconing will
work but that appears to be a separate problem.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patch fixes the following bugs at
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2005http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=2007
If we suspend with an association and then resumed,
we need to synchronize the active rxon with staging rxon,
else we will get an error when iwl_alive_start try to commit
rxon and staging is set to channel 0. Before going to suspend
staging and active rxon are in sync. After resuming from the
suspend, iwl_mac_start is called and it clears the staging
rxon. Patch fixes the bug by not clearing the staging rxon
in iwl_mac_start.
Patch also adds similar fix to 3945.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for both mixed and pure 40MHz, need to check for valid channel location.
if the specified channel not allow the channel location requested
(ABOVE, BELOW), then reject the Fat channel access
This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1988
("iwlwifi: checking for 40MHz mode" and "iwlwifi: check control channel
for pure 40MHz" combine with this to address the above bug. -- JWL)
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for pure 40MHz mode, set the control channel location if provided, but not
like Mixed mode; if information is not provided, still allow 40MHz
operation.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when checking for 40MHz, compare ht_protection to
IEEE80211_HT_OP_MODE_PROTECTION_20MHZ. ht_protection is not a bit-mask
field
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My earlier patch,
"mac80211: unify config_interface and bss_info_changed"
introduced a bug in iwlwifi where it will do some things
incorrectly now when reassociating.
Revamp iwl_bss_info_changed to fix that issue and make it
easier to read. Also, while at it, add comments about things
that it should do but currently doesn't.
Finally, also improve the locking in the function.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The card firmware does not set the Command Download Ready interrupt bit
when IEEE PS mode is enabled, preventing the driver from sending
commands (such as the command to exit IEEE PS mode) since there is no
indication that the card is ready to accept commands.
This patch works around the problem by using the the TX Download Ready
bit in place of the Command Download Ready Bit while in IEEE PS mode.
TX Download Ready is set in IEEE PS mode.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
powerpc: Fix bug in move of altivec code to vector.S
powerpc: Add support for swiotlb on 32-bit
powerpc/spufs: Remove unused error path
powerpc: Fix warning when printing a resource_size_t
powerpc/xmon: Remove unused variable in xmon.c
powerpc/pseries: Fix warnings when printing resource_size_t
powerpc: Shield code specific to 64-bit server processors
powerpc: Separate PACA fields for server CPUs
powerpc: Split exception handling out of head_64.S
powerpc: Introduce CONFIG_PPC_BOOK3S
powerpc: Move VMX and VSX asm code to vector.S
powerpc: Set init_bootmem_done on NUMA platforms as well
powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
powerpc/mm: Fix some SMP issues with MMU context handling
powerpc: Add PTRACE_SINGLEBLOCK support
fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
powerpc/virtex: Add ml510 reference design device tree
powerpc/virtex: Add Xilinx ML510 reference design support
powerpc/virtex: refactor intc driver and add support for i8259 cascading
powerpc/virtex: Add support for Xilinx PCI host bridge
...
CNIC and BNX2I must depend on PCI. Dependencies do not get
propagated through select.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mlx4: Add strong ordering to local inval and fast reg work requests
IB/ehca: Remove superfluous bitmasks from QP control block
RDMA/cxgb3: Limit fast register size based on T3 limitations
RDMA/cxgb3: Report correct port state and MTU
mlx4_core: Add module parameter for number of MTTs per segment
IB/mthca: Add module parameter for number of MTTs per segment
RDMA/nes: Fix off-by-one bugs in reset_adapter_ne020() and init_serdes()
infiniband: Remove void casts
IB/ehca: Increment version number
IB/ehca: Remove unnecessary memory operations for userspace queue pairs
IB/ehca: Fall back to vmalloc() for big allocations
IB/ehca: Replace vmalloc() with kmalloc() for queue allocation
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice. Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time. This is the same bug that was reported in ib_mthca by Yinghai
Lu <yhlu.kernel@gmail.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Need to rework how bonding devices are initialized to make it more
amenable to creating bonding devices via netlink.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove bogus non-portable possibly unaligned way of testing
for zero addres..
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding device acts unlike all other Linux network device functions
in that it ignores case of device names. The developer must have come
from windows!
Cleanup the management of names and use standard routines where possible.
Flag places where bonding device still doesn't work right with network
namespaces.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "expected_refcount" stuff in bonding sysfs module is a mistake.
Sysfs does proper refcounting, and it is okay to remove a bond device
that has some user process holding the file open.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve some of the complaints from checkpatch, and remove "magic emacs format"
comments, and useless MODULE_SUPPORTED_DEVICE(). But should not
change actual code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not safe to use a network device destructor that is a function in
the module, since it can be called after module is unloaded if sysfs
handle is open.
When eventually using netlink, the device cleanup code needs to be done
via uninit function.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole read/write semaphore locking can be removed. It doesn't add any
protection that isn't already done by using the RTNL mutex properly.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid a unnecessary carrier state transistion that happens when device
is registered.
Lockdep works better if initialization is done before registration as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_create() is always called with same parameters so move the argument
down.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/cnic.c: In function ‘init_bnx2_cnic’:
drivers/net/cnic.c:2520: error: implicit declaration of function ‘__symbol_get’
drivers/net/cnic.c:2520: warning: assignment makes pointer from integer without a cast
make[1]: *** [drivers/net/cnic.o] Error 1
make: *** [drivers/net/cnic.o] Error 2
Caused by not including linux/module.h
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix cnic build for case of CONFIG_INET=n.
Fix cnic build for case of CONFIG_IPV6=m and CONFIG_CNIC=y.
Fixes these build errors:
cnic.c:(.text+0x236a1d): undefined reference to `ip_route_output_key'
cnic.c:(.text+0x15a8e8): undefined reference to `ip6_route_output'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up USB drivers that return an errno value (result of usb_submit_urb())
to qdisc_restart(), causing qdisc_restart() to print a warning and requeue/
retransmit the skb.
- hso: skb is freed: use after free
- at76_usb: skb is freed: use after free
Compile tested only.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up hamradio drivers that return an errno value to dev_queue_xmit(), causing
it to print a warning an free the skb.
- bpqether: skb is freed: use after free
Compile tested only.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up WAN drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- cycx_x25: intention appears to be to requeue the skb
Does not compile cleanly for me even without this patch, so untested.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: fix network drivers ndo_start_xmit() return values (part 3)
Fix up wireless drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- airo: transmission not implemented for chip, intention is to free and abort
- ipw2200: transmission not implemented for promiscous mode, intention is to
drop
- prism54: intention is to drop
- wl3501_cs: intention appears to be to drop
- zd1201: error counter indicates intention is to drop
All drivers compile tested.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up IRDA drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning an requeue/retransmit the skb.
- donauboe: intention appears to be to have the skb retransmitted without
error message
- irda-usb: intention is to drop silently according to comment
- kingsub-sir: skb is freed: use after free
- ks959-sir: skb is freed: use after free
- ksdazzle-sir: skb is freed: use after free
- mcs7880: skb is freed: use after free
All but donauboe compile tested.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up drivers that return an errno value to qdisc_restart(), causing
qdisc_restart() to print a warning and requeue/retransmit the skb.
- xpnet: memory allocation error, intention is to drop
- ethoc: oversized packet, packet must be dropped
- ibmlana: skb freed: use after free
- rrunner: skb freed: use after free
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sir retries count reaches -1 rather than 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Graff Yang <graff.yang@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (154 commits)
[SCSI] osd: Remove out-of-tree left overs
[SCSI] libosd: Use REQ_QUIET requests.
[SCSI] osduld: use filp_open() when looking up an osd-device
[SCSI] libosd: Define an osd_dev wrapper to retrieve the request_queue
[SCSI] libosd: osd_req_{read,write} takes a length parameter
[SCSI] libosd: Let _osd_req_finalize_data_integrity receive number of out_bytes
[SCSI] libosd: osd_req_{read,write}_kern new API
[SCSI] libosd: Better printout of OSD target system information
[SCSI] libosd: OSD2r05: Attribute definitions
[SCSI] libosd: OSD2r05: Additional command enums
[SCSI] mpt fusion: fix up doc book comments
[SCSI] mpt fusion: Added support for Broadcast primitives Event handling
[SCSI] mpt fusion: Queue full event handling
[SCSI] mpt fusion: RAID device handling and Dual port Raid support is added
[SCSI] mpt fusion: Put IOC into ready state if it not already in ready state
[SCSI] mpt fusion: Code Cleanup patch
[SCSI] mpt fusion: Rescan SAS topology added
[SCSI] mpt fusion: SAS topology scan changes, expander events
[SCSI] mpt fusion: Firmware event implementation using seperate WorkQueue
[SCSI] mpt fusion: rewrite of ioctl_cmds internal generated function
...
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This replaces find_vq/del_vq with find_vqs/del_vqs virtio operations,
and updates all drivers. This is needed for MSI support, because MSI
needs to know the total number of vectors upfront.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ lguest/9p compile fixes)
Add a linked list of all virtqueues for a virtio device: this helps for
debugging and is also needed for upcoming interface change.
Also, add a "name" field for clearer debug messages.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We need to enforce the IP alignment on the non-mergeable RX path just
like the other RX path. Not doing so results in misaligned IP
headers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers incorrectly use ntohs() instead of htons()
A cleanup as htons() returns same result than ntohs(),
but better to use the proper one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SH4's BUG() seems to confuse the compiler as it is considered to
return; thus, some functions would trigger usage of uninitialized
variables or non-void functions returning void.
Work around by initializing/returning.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Some users still load bond module multiple times to create bonding
devices. This accidentally was broken by a later patch about
the time sysfs was fixed. According to Jay, it was broken
by:
commit b8a9787edd
Author: Jay Vosburgh <fubar@us.ibm.com>
Date: Fri Jun 13 18:12:04 2008 -0700
bonding: Allow setting max_bonds to zero
Note: sysfs and procfs still produce WARN() messages when this is done
so the sysfs method is the recommended API.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the i2400m device resets, the driver code will force some
functions to return a -ERESTARTSYS error code, which can is used by
the caller to determine which recovery actions to take.
However, in certain situations the only thing that can be done is to
bubble up said error code to user space, for handling.
However, -ERESTARSYS was a poor choice, as it is supposed to be used
by the kernel only.
As such, replace -ERESTARTSYS with -EL3RST; as well, in
i2400m_msg_to_dev(), when the device is in boot mode (following a
recent reset), return -EL3RST instead of -ENODEV (meaning the device
is in bootrom mode after a reset, not that the device was
disconnected, and thus, normal commands cannot be executed).
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
When a device reset happens during firmware load [in
i2400m_dev_bootstrap()], __i2400m_dev_start() will retry a number of
times. However, for those retries to be able to accomplish anything,
the device's bootrom has to be reinitialized.
Thus, on the retry path, pass the I2400M_MAC_REINIT to the firmware
load code.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
The current SDIO code was working in polling mode for boot-mode
(firmware load) mode. This was causing issues on some hardware.
Moved all the RX code to use a unified IRQ handler that based on the
type of data the device is sending can discriminate and decide which
is the right destination.
As well, all the reads from the device are made to be at least the
block size (256); the driver will ignore the rest when not needed.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When i2400m_bootrom_init() fails to put the device into a state of
being ready to accept firmware, the driver was currently trying to
reset it if it failed to do so. This is not too useful; as part of
trying to put the device in the right state a few resets have already
been tried.
At this point, things are probably fried out and an extra reset might
do more harm than good (for example causing reseting of other
functions in the same composite device).
So it is left up to the callers to determine the error path to take
(at the end this is always i2400m_setup(), who depending on how many
retries are left, might give up on the device).
From a fix by Cindy H. Kao.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
This change moves the table of "pokes" performed on the device at boot
time to the bus specific portion of the driver.
Different models of the i2400m device supported by this driver require
different poke tables, thus having a single table that works for all
is impossible. For that, the table is moved to the bus-specific
driver, who can decide which table to use based on the specifics of
the device and point the generic driver to it.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
The code that sets up the i2400m (firmware load and general driver
setup after it) includes a couple of retry loops.
The SDIO device sometimes can get in more complicated corners than the
USB one (due to its interaction with other SDIO functions), that
require trying a few more times.
To solve that, without having a failing USB device taking longer to be
considered dead, allow the retry counts to be specified by the
bus-specific driver, which the general driver takes as a parameter.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When a device reboot happens when we are under probe, with init_mutex
taken, make sure we can recover. Have dev_reset_handle set boot mode
and i2400m_msg_to_dev() will see it and fail gracefully instead of
timing out.
Found and diagnosed by Cindy H. Kao.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When the TX FIFO filled up and i2400m_tx_new() failed to allocate a
new TX message header, a missing check for said condition was causing a
kernel oops when trying to dereference a NULL i2400m->tx_msg pointer.
Found and diagnosed by Cindy H. Kao.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
i2400m_dev_shutdown() tried to reset the device to put it in a known
state before shutting down.
But that turned out to be pointless. We reach this case in two paths:
1 - when the device resets, to clean up state
2 - when the driver is unloaded, for the same
however, in both cases it is pointless; in (1) the device is already
reset, why do it again? in (2) we can't -- the USB stack, for example,
doesn't allow communicating with the device when the driver is being
unbound and if the device is disconnected, the device is gone already.
So just remove it. Leave the function as a placeholder for future
cleanups that will be done from data allocated by the driver during
device operation.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
i2400m_tx_skip_tail() needs to handle the special case of being called
when the tail room that is left over in the FIFO is zero.
This happens when a TX message header was opened at the very end of
the FIFO (without payloads). The i2400m_tx_close() code already marked
said TX message (header) to be skipped and this function should be
doing nothing.
It is called anyway because it is part of a common "corner case" path
handling which takes care of more cases than only this one.
The tail room computation was also improved to take care of the case
when tx_in is at the end of the buffer boundary; tail_room has to be
modded (%) to the buffer size. To do that in a single well-documented
place, __i2400m_tx_tail_room() is introduced and used.
Treat i2400m->tx_in == 0 as a corner case and handle it accordingly.
Found and diagnosed by Cindy H. Kao.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
In some situations, when a new TX message header is started, there
might be no space for data payloads. In this case the message is left
with zero payloads and the i2400m_tx_close() function has just to mark
it as "to skip". If it tries to go ahead it will overwrite things
because there is no space to add padding as defined by the
bus-specific layer. This can cause buffer overruns and in some stress
cases, panics.
Found and diagnosed by Cindy H. Kao.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The constant is being use as an alignment factor, not as a padding
factor; made reading/reviewing the code quite confusing.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
This reset type causes the WiMAX function to be disabled and
re-enabled, which will force the WiMAX device to reset and enter boot
mode.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
By mistake, the BUG_ON() check was left in there and it will fail when
called if i2400m->work_queue is still not setup.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
RX support is the only user of the work-queue, to process
reports/notifications from the device. Thus, it needs the work queue
to be initialized first.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reported and fixed by Cindy H Kao.
When the device is stopped __i2400m_dev_stop() stops the network
queue.
However, when this is done in the middle of heavy network operation,
when the bus-specific subdriver is still wrapping up and it reports a
sent TX transaction with _tx_msg_sent() right after the device was
stopped, the queue was being started again, which was causing a stream
of oopsen and finally a panic.
In any case, said call has no place there. It's a left over from an
early implementation that was discarded later on.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m driver waits for the device to report being ready for
entering power save before asking it to do so. This module parameter
allows control of said operation; if disabled, the driver won't ask
the device to enter power save mode.
This is useful in setups where power saving is not so important or
when the overhead imposed by network reentry after power save is not
acceptable; by combining this with parameter 'idle_mode_disabled', the
driver will always maintain both the connection and the device in
active state.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
vfree() does its own 'NULL' check, so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the tx queue destroy path, be_tx_q_clean() is currently called after the tx queues are freed; it must be called before.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_rx_compl_get() must not reset(via the valid word) the rx_compl as the rx_compl is not processed yet; it must be reset after it is processed.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx stats are not getting updated when an rx_compl with only one frag is rcvd in non-lro path.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix netdev stat rx_errors to cover length related errors and checksum errors and rx_dropped to the pkts dropped due to lack of buffers
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cancel_delayed_work_sycn instead of cancel_delayed_work() to reliably kill be_worker() as it rearms itself.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vfree() does its own 'NULL' check, so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vfree() does its own 'NULL' check, so no need for check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-allocate a skb at init time to be used for control messages to the HW
if skb allocation fails.
Tolerate failures to send messages initializing some memories at the cost of
parity error detection for these memories.
Retry sending connection id release messages if both alloc_skb(GFP_ATOMIC)
and alloc_skb(GFP_KERNEL) fail.
Do not bring the interface up if messages binding queue set to port fail to
be sent.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_tx_interrupt() is used from NAPI context, it can
directly free skbs. dev_kfree_skb_irq() is a leftover from
pre-NAPI times of this driver.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is available in a standard MDIO register in 10GBASE-T PHYs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX buffer rings can be comprised of non-contiguous fixed
size chunks of memory. The ring is given to the hardware
as a pointer to a location that stores the location of
the queue. If the queue is greater than 4096 bytes then
the hardware gets a list of said pointers.
This patch addes the necessary logic to generate the list if
the queue size exceeds 4096.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The alignment was on size of queue boundary, but the hardware
only requires 4-byte alignment.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WAKE_MCAST bit is tested twice, the first should be WAKE_UCAST.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <csnook@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a configurable Descriptor Skip Length for systems that lack cache
coherence.
(akpm: I think this should be done as a module parameter, not a
compile-tinme option)
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Cc: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=13348
akpm: the reporter disappeared, so I typed it in again.
It is not possible to make clone of tagged VLAN interface to be used as
mac-based vlan interfave.
How reproducible:
Use any 802.1q tagged vlan interface, e.g. eth2.700 and clone it:
ip link add link eth2.700 address 00:04:75:cb:38:09 macvlan0 type macvlan
ip link set dev macvlan0 up
ip addr add 10.195.1.1/24 dev macvlan0
So far, so good. Now try to ping anything via macvlan0:
ping 10.195.1.2
Actual results:
For every attempted packet tx kernel writes to console:
------------[ cut here ]------------
WARNING: at net/8021q/vlan_dev.c:254 vlan_dev_hard_header+0x36/0x126 [8021q]()
Hardware name: M22ES
Modules linked in: arptable_filter arp_tables bridge veth macvlan arc4 ecb
ppp_mppe ppp_async crc_ccitt ppp_generic slhc autofs4 sunrpc 8021q garp stp
ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 xt_state nf_conntrack xt_tcpudp
x_tables dm_mirror dm_region_hash dm_log dm_multipath dm_mod sbs sbshc lp
floppy snd_intel8x0 joydev snd_seq_dummy snd_intel8x0m snd_ac97_codec
ide_cd_mod ac97_bus snd_seq_oss cdrom snd_seq_midi_event serio_raw snd_seq
snd_seq_device snd_pcm_oss snd_mixer_oss parport_pc snd_pcm parport battery
8139cp snd_timer i2c_sis96x ac button snd rtc_cmos rtc_core 8139too soundcore
rtc_lib mii i2c_core pcspkr snd_page_alloc pata_sis libata sd_mod scsi_mod ext3
jbd ehci_hcd ohci_hcd uhci_hcd [last unloaded: ip_tables]
Pid: 0, comm: swapper Tainted: G W 2.6.29.3 #1
Call Trace:
[<c0425f48>] warn_slowpath+0x60/0x9f
[<c0425f6f>] warn_slowpath+0x87/0x9f
[<dffb850d>] vlan_dev_hard_header+0x0/0x126 [8021q]
[<dffb8543>] vlan_dev_hard_header+0x36/0x126 [8021q]
[<dffb850d>] vlan_dev_hard_header+0x0/0x126 [8021q]
[<df83155d>] macvlan_hard_header+0x3c/0x47 [macvlan]
[<df831521>] macvlan_hard_header+0x0/0x47 [macvlan]
[<c062bf3f>] arp_create+0xef/0x1ff
[<c062c08c>] arp_send+0x3d/0x54
[<c062c916>] arp_solicit+0x16c/0x177
[<c05fadd2>] neigh_timer_handler+0x227/0x269
[<c05fabab>] neigh_timer_handler+0x0/0x269
[<c042ce4d>] run_timer_softirq+0xf0/0x141
[<c0429e5a>] __do_softirq+0x76/0xf8
[<c0429de4>] __do_softirq+0x0/0xf8
<IRQ> [<c044fb67>] handle_level_irq+0x0/0xad
[<c0429db7>] irq_exit+0x35/0x62
[<c04046bb>] do_IRQ+0xdf/0xf4
[<c04035a7>] common_interrupt+0x27/0x2c
[<c04079c5>] default_idle+0x2a/0x3d
[<c0401bb6>] cpu_idle+0x57/0x70
Macvlan driver always uses standard ethernet header length for all types
of interface to which it is linked. This patch fixes this problem.
Reported-by: <sg.tweak@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore support for cards with MII-lacking PHYs as compared to removed
pre-2.6.29 eepro100 driver: use full low-level MII I/O access abstraction
by providing clean PHY-specific mdio_ctrl() functions for either standard
MII-compliant cards, slightly special ones or non-MII PHY ones.
We now have another netdev_priv member for mdio_ctrl(), thus we have some
array indirection, but we save some additional opcodes for specific
phy_82552_v handling in the common case.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Andreas Mohr <andi@lisas.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always enable rfkill since the ifdefs in the code is not really worth
the Kconfig option. Also fix a few code style things, and remove the
usage of the ah_gpio[] array so we can remove it later.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch along with my previous patch in mac80211 "Fix the
way ADDBA count..", fixes hang in tx when connected to an HT
AP which rejects/times out on addba req.
AGGR_ADDBA_PROGRESS should be cleared in aggr state when addba
negotiation is terminated due to either addba response is timed out
or addba is denied by the AP. With out clearing this bit,
all frames are queued onto s/w queue for getting tx'd as aggr and
will never be scheduled onto hw queue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add automagic feature flags, so the firmware can tell the driver
about supported features and the driver can switch features on/off as
needed.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ports the b43/legacy rfkill code to the new API offered
by cfg80211 and thus removes a lot of useless stuff.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces initial rfkill support for the ath5k driver
based on rfkill support in the cfg80211 framework.
All rfkill related code is separated into newly created rfkill.c.
Changes to existing code are minimal:
* added a new data structure ath5k_rfkill to the ath5k_softc structure
* inserted calls to HW rfkill init/deinit routines
* ath5k_intr() has been extended to handle AR5K_INT_GPIO interrupts
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is a back-port from aggregation testing code.
In the past, we didn't limit the amount of active tx urbs.
However, ar9170 only has a limited buffer reserved for
pending data frames.
This wasn't much of a problem with the slower 802.11b/g.
We simply stopped the full queue and moved on to something different
in the mean time. But - as you guessed it - this simple approach
stands in way for a decent aggregation implementation.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds new commands that the original firmware will not send
but we can use them to debug firmware.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix possible unaligned u32 access in b43_generate_plcp_hdr().
Unaligned data is read/write with a u32 pointer instead of using the
packed structure. Some versions of gcc ignore the "packed" attribute, if the
structure element is accessed through a local pointer.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the dependency on GPIO framework and lets the SPI host
driver handle the chip select. The SPI host driver is required to keep
the CS active for the entire message unless cs_change says otherwise.
This patch collects the two/three single SPI transfers into a message.
Also the delay in read path in case use_dummy_writes are not used is
moved into the SPI host driver.
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver used to be named rndis_wext before inclusion to upstream. Since
rndis_wlan is being converted to cfg80211, use of rndis_wext* names
can be confusing. So rename all rndis_wext to rndis_wlan (as should
have been when driver was renamed).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
