VLAN entries on a port can be associated with either a bridge VLAN or a
router port. Before the VLAN entry is destroyed these associations need
to be cleaned up.
Currently, this is always invoked from the function which destroys the
VLAN entry, but next patch is going to skip the destruction of the
default entry when a port in unlinked from a LAG.
The above does not mean that the associations should not be cleaned up,
so add a helper that will be invoked from both call sites.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches will need to access the default port VLAN. Since this
VLAN will exist throughout the lifetime of the port, simply store it in
the port's struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function allows flushing all the existing VLAN entries on a port. It
is invoked when a port is destroyed and when it is unlinked from a LAG.
In the latter case, when moving to the new default VLAN, there will not
be a need to destroy the default VLAN entry.
Therefore, add an argument that allows to control whether the default
port VLAN should be destroyed or not. Currently it is always set to
'true'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver does not set the port's PVID when initializing a
new port. This is because the driver is using VID 1 as PVID which is the
firmware default.
Subsequent patches are going to change the PVID the driver is setting
when initializing a new port.
Prepare for that by explicitly setting the port's PVID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to replace the current default VID (1) with
VLAN_N_VID - 1 (4095).
Prepare for this conversion by replacing the hard-coded '1' with a
define.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In symmetric routing, the only two members in the VLAN corresponding to
the L3 VNI are the router port and the VXLAN tunnel.
In case the VXLAN device is already enslaved to the bridge and only
later the VLAN interface is configured, the tunnel will not be
offloaded.
The reason for this is that when the router interface (RIF)
corresponding to the VLAN interface is configured, it calls the core
fid_get() API which does not check if NVE should be enabled on the FID.
Instead, call into the bridge code which will check if NVE should be
enabled on the FID.
This effectively means that the same code path is used to retrieve a FID
when either a local port or a router port joins the FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-12-20
This series contains updates to e100, igb, ixgbe, i40e and ice drivers.
I replaced spinlocks for mutex locks to reduce the latency on CPU0 for
igb when updating the statistics. This work was based off a patch
provided by Jan Jablonsky, which was against an older version of the igb
driver.
Jesus adjusts the receive packet buffer size from 32K to 30K when
running in QAV mode, to stay within 60K for total packet buffer size for
igb.
Vinicius adds igb kernel documentation regarding the CBS algorithm and
its implementation in the i210 family of NICs.
YueHaibing from Huawei fixed the e100 driver that was potentially
passing a NULL pointer, so use the kernel macro IS_ERR_OR_NULL()
instead.
Konstantin Khorenko fixes i40e where we were not setting up the
neigh_priv_len in our net_device, which caused the driver to read beyond
the neighbor entry allocated memory.
Miroslav Lichvar extends the PTP gettime() to read the system clock by
adding support for PTP_SYS_OFFSET_EXTENDED ioctl in i40e.
Young Xiao fixed the ice driver to only enable NAPI on q_vectors that
actually have transmit and receive rings.
Kai-Heng Feng fixes an igb issue that when placed in suspend mode, the
NIC does not wake up when a cable is plugged in. This was due to the
driver not setting PME during runtime suspend.
Stephen Douthit enables the ixgbe driver allow DSA devices to use the
MII interface to talk to switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5 updates taken for dependencies on following patches.
* branche 'mlx5-next': (23 commits)
IB/mlx5: Introduce uid as part of alloc/dealloc transport domain
net/mlx5: Add shared Q counter bits
net/mlx5: Continue driver initialization despite debugfs failure
net/mlx5: Fold the modify lag code into function
net/mlx5: Add lag affinity info to log
net/mlx5: Split the activate lag function into two routines
net/mlx5: E-Switch, Introduce flow counter affinity
IB/mlx5: Unify e-switch representors load approach between uplink and VFs
net/mlx5: Use lowercase 'X' for hex values
net/mlx5: Remove duplicated include from eswitch.c
net/mlx5: Remove the get protocol device interface entry
net/mlx5: Support extended destination format in flow steering command
net/mlx5: E-Switch, Change vhca id valid bool field to bit flag
net/mlx5: Introduce extended destination fields
net/mlx5: Revise gre and nvgre key formats
net/mlx5: Add monitor commands layout and event data
net/mlx5: Add support for plugged-disabled cable status in PME
net/mlx5: Add support for PCIe power slot exceeded error in PME
net/mlx5: Rework handling of port module events
net/mlx5: Move flow counters data structures from flow steering header
...
Use the mii_bus callbacks to address the entire clause 22/45 address
space. Enables userspace to poke switch registers instead of a single
PHY address.
The ixgbe firmware may be polling PHYs in a way that is not protected by
the mii_bus lock. This isn't new behavior, but as Andrew Lunn pointed
out there are more addresses available for conflicts.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Most dsa devices expect a 'struct mii_bus' pointer to talk to switches
via the MII interface.
While this works for dsa devices, it will not work safely with Linux
PHYs in all configurations since the firmware of the ixgbe device may
be polling some PHY addresses in the background.
Signed-off-by: Stephen Douthit <stephend@silicom-usa.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I210 ethernet card doesn't wakeup when a cable gets plugged. It's
because its PME is not set.
Since commit 42eca23021 ("PCI: Don't touch card regs after runtime
suspend D3"), if the PCI state is saved, pci_pm_runtime_suspend() stops
calling pci_finish_runtime_suspend(), which enables the PCI PME.
To fix the issue, let's not to save PCI states when it's runtime
suspend, to let the PCI subsystem enables PME.
Fixes: 42eca23021 ("PCI: Don't touch card regs after runtime suspend D3")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If ice driver has q_vectors w/ active NAPI that has no rings,
then this will result in a divide by zero error. To correct it
I am updating the driver code so that we only support NAPI on
q_vectors that have 1 or more rings allocated to them.
See commit 13a8cd191a ("i40e: Do not enable NAPI on q_vectors
that have no rings") for detail.
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Acked-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Out of bound read reported by KASan.
i40iw_net_event() reads unconditionally 16 bytes from
neigh->primary_key while the memory allocated for
"neighbour" struct is evaluated in neigh_alloc() as
tbl->entry_size + dev->neigh_priv_len
where "dev" is a net_device.
But the driver does not setup dev->neigh_priv_len and
we read beyond the neigh entry allocated memory,
so the patch in the next mail fixes this.
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a static code checker warning:
drivers/net/ethernet/intel/e100.c:1349
e100_load_ucode_wait() warn: passing zero to 'PTR_ERR'
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 4.5.9 of the datasheet says that the total size of all packet
buffers combined (TxPB 0 + 1 + 2 + 3 + RxPB + BMC2OS + OS2BMC) must not
exceed 60KB. Today we are configuring a total of 62KB, so reduce the
RxPB from 32KB to 30KB in order to respect that.
The choice of changing RxPBSIZE here is mainly because it seems more
correct to give more priority to the transmit packet buffers over the
receiver ones when running in Qav mode. Also, the BMC2OS and OS2BMC
sizes are already too short.
Signed-off-by: Jesus Sanchez-Palencia <jesus.s.palencia@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is based off of the work and suggestion of Jan Jablonsky
<jan.jablonsky@thalesgroup.com>.
The Watchdog workqueue in igb driver is scheduled every 2s for each
network interface. That includes updating a statistics protected by
spinlock. Function igb_update_stats in this case will be protected
against preemption. According to number of a statistics registers
(cca 60), processing this function might cause additional cpu load
on CPU0.
In case of statistics spinlock may be replaced with mutex, which
reduce latency on CPU0.
CC: Bernhard Kaindl <bernhard.kaindl@thalesgroup.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ath.git patches for 4.21. Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This issue arise in a race condition between ath10k_sta_state() and
ath10k_htt_fetch_peer_stats(), explained in below scenario
Steps:
1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion
when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST
state.
2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message.
In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after
the peer validation check.
Since arsta->tx_stats get freed before the peer deletion [1].
ath10k_htt_fetch_peer_stats() ended up in "use after free" situation.
Fixed this issue by moving the arsta->tx_stats free handling after the
peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in
"use after free" situation.
Kernel Panic:
Unable to handle kernel NULL pointer dereference at virtual address 00000286
pgd = d8754000
[00000286] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 6245 Comm: hostapd Not tainted
task: dc44cac0 ti: d4a38000 task.ti: d4a38000
PC is at kmem_cache_alloc+0x7c/0x114
LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core]
pc : [<c02bdc50>] lr : [<bf916b78>] psr: 20000013
sp : d4a39b88 ip : 00000000 fp : 00000001
r10: 00000000 r9 : 1d3bc000 r8 : 00000dc0
r7 : 000080d0 r6 : d4a38000 r5 : dd401b00 r4 : 00000286
r3 : 00000000 r2 : d4a39ba0 r1 : 000080d0 r0 : dd401b00
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5787d Table: 5a75406a DAC: 00000015
Process hostapd (pid: 6245, stack limit = 0xd4a38238)
Stack: (0xd4a39b88 to 0xd4a3a000)
...
[<c02bdc50>] (kmem_cache_alloc) from [<bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core])
[<bf916b78>] (ath10k_sta_state [ath10k_core]) from [<bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211])
[<bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211])
[<bf88634c>] (ieee80211_add_station [mac80211]) from [<bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211])
[<bf83f3c4>] (nl80211_new_station [cfg80211]) from [<bf6c4040>] (extack_doit+0x2c/0x74 [compat])
[<bf6c4040>] (extack_doit [compat]) from [<c05c285c>] (genl_rcv_msg+0x274/0x30c)
[<c05c285c>] (genl_rcv_msg) from [<c05c1d98>] (netlink_rcv_skb+0x58/0xac)
[<c05c1d98>] (netlink_rcv_skb) from [<c05c25d4>] (genl_rcv+0x20/0x34)
[<c05c25d4>] (genl_rcv) from [<c05c1750>] (netlink_unicast+0x11c/0x204)
[<c05c1750>] (netlink_unicast) from [<c05c1be0>] (netlink_sendmsg+0x30c/0x370)
[<c05c1be0>] (netlink_sendmsg) from [<c0587e90>] (sock_sendmsg+0x70/0x84)
[<c0587e90>] (sock_sendmsg) from [<c058970c>] (___sys_sendmsg.part.3+0x188/0x228)
[<c058970c>] (___sys_sendmsg.part.3) from [<c058a594>] (__sys_sendmsg+0x4c/0x70)
[<c058a594>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
Code: ebfffec1 e1a04000 ea00001b e5953014 (e7940003)
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon
Hardware tested: QCA9984
Firmware tested: 10.4-3.6.0.1-00004
Fixes: a904417fc ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state':
drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning:
variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable]
'num_tdls_vifs' not used any more after
9a993cc1ea ("ath10k: fix the logic of limiting tdls peer counts")
Also, remove the single called function ath10k_mac_tdls_vifs_count
and ath10k_mac_tdls_vifs_count_iter.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The top word of the constant can only have bits set if sign
extension set it to all-1, therefore we don't really have to
mask the top half of the register. We can just OR it into
the result as is.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The verifier will now understand the JSET instruction, so don't
mark the dead branch in the JIT as noop. We won't generate any
code, anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
For a little better performance on faster machines and faster link
speeds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older firmware only supports 16-bit flow handle, because of which the
number of flows that can be offloaded can’t scale beyond a point.
Newer firmware supports 64-bit flow handle enabling the host to scale
upto millions of flows. With the new 64-bit flow handle support, driver
has to query flow stats in a different way compared to the older approach.
This patch adds support for 64-bit flow handle and new way to query
flow stats.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If RDMA is supported on the 57500 chip, increase context memory
allocations for the resources used by RDMA.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the new functions bnxt_alloc_ctx_pg_tbls()/bnxt_free_ctx_pg_tbls()
to allocate and free pages for context memory. The new functions
will handle the different levels of paging support and allocate/free
the pages accordingly using the existing functions.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support level 2 context page memory structures, enhance the
bnxt_ring_mem_info structure with a "depth" field to specify the page
level and add a flag to specify using full pages for L1 and L2 page
tables. This is needed to support RDMA functionality on 57500 chips
since RDMA requires more context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier, some of the firmware commands (ex: CFA_FLOW_*) which are processed
by KONG processor were sent to the CHIMP processor from the host. This
approach was taken as there was no direct message channel to KONG.
CHIMP in turn used to send them to KONG. Newer firmware supports a new
message channel which the host can send messages directly to the KONG
processor.
This patch adds support for required changes needed in the driver
to support direct KONG message channel. This speeds up flow related
messages sent to the firmware for CLS_FLOWER offload.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These routines will be enhanced in the subsequent patch to
return the 2nd firmware comm. channel's hwrm response address &
sequence id respectively.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typecast hwrm_cmd_resp_addr to (u8 *) from (void *) before doing
arithmetic.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding a 2nd communication channel to firmware.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set hwrm_intr_seq_id value to its inverted value instead of
HWRM_SEQ_INVALID, when an hwrm completion of type
CMPL_BASE_TYPE_HWRM_DONE is received. This will enable us to use
the complete 16-bit sequence ID space.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The major changes are in the flow offload firmware APIs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_MLX5_ESWITCH is not defined, test for SR-IOV being disabled,
instead of calling e-switch LAG prereq routine.
Since LAG with SRIOV is allowed only when switchdev mode is on.
Fixes: eff849b2c6 ("net/mlx5: Allow/disallow LAG according to pre-req only")
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
vport system image guid should be queried using vport nic API for
Ethernet ports, and vport hca API for Infiniband ports.
Fixes: fadd59fc50 ("net/mlx5: Introduce inter-device communication mechanism")
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Generate encap header depending on the routed device to support
native/tagged Ethernet header.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support generation of native or tagged Ethernet header for encap
header, depending on provided net device.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Change the order to first route IPv4/6 and return if error. Only after
successful route continue to allocate an encap header, with no
functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In tunnel encap we prepare the encap header for IPv4/6 cases, in two
separate functions. For ETH header generation the code is almost
duplicated.
Move the ETH header generation code from IPv4/6 functions to a helper
function, with no functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we don't support nor fail attempts to offload encap flows routed
to vlan device on the underlay network. We wrongly consider a vlan underlay
device to be on the same e-switch b/c the switchdev ID is retrieved recursively.
Add explicit check for that and fail such attempts.
Also align to a more strict check for the ingress and the underlay devices
to practically be on the same eswitch.
Fixes: ce99f6b97f ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Fixes: 3e621b19b0 ('net/mlx5e: Support TC encapsulation offloads with upper devices')
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For tunnel we determine the output devs for IPv4/6 cases, in two
separate functions, with a duplicated code.
Move that code from IPv4/6 functions to a helper function, with no
functional change.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We use the switchdev parent HW id helper to identify if the mirred device
shares the same ASIC/port with the ingress device. This can get us wrong
in the presence of upper devices such as vlan or bridge set over the HW
devices (VF or uplink representors), b/c the switchdev ID is retrieved
recursively.
To fail offload attempts in such cases, we condition the check on the
egress device to have not only the same switchdev ID but also the relevant
mlx5 netdev ops.
Fixes: 03a9d11e6e ('net/mlx5e: Add TC drop and mirred/redirect action parsing for SRIOV offloads')
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There are cases (e.g tunneling with vlan on underlay and potentially
more) where this makes sense, so allow that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The default size for the VF representors' SQ was too small to handle high
packet rates. Doubling the size from 64 to 128 drastically improves the
packet rate under stress (by about 50%), whereas increasing the size
beyond 128 has not shown to make any further difference.
The impact of the SQ size was measured with UDP traffic, in the following
topology: TG <-> PF <-> TC forwarding <-> VF representor <-> VF in VM
over a single core processing bi-directional traffic, with the following
results:
SQ size of 64: SQ size of 128:
Packet rate for 64B UDP packets: 860 [Kpps] 1280 [Kpps]
Packet rate for 114B VxLan
encapsulated UDP packets: 320 [Kpps] 500 [Kpps]
Signed-off-by: Gavi Teitz <gavi@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Read the system time right before and immediately after reading the low
register of the internal timer. This adds support for the
PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The timecounter needs to be updated at least once in half of the
cyclecounter interval to prevent timecounter_cyc2time() interpreting a
new timestamp as an old value and causing a backward jump.
This would be an issue if the timecounter multiplier was so small that
the update interval would not be limited by the 64-bit overflow in
multiplication.
Shorten the calculated interval to make sure the timecounter is updated
in time even when the system clock is slowed down by up to 10%, the
multiplier is increased by up to 10%, and the scheduled overflow check
is late by 15%.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ariel Levkovich <lariel@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch removes the redundant variable initialization,
as driver will devm_kzalloc to set value to hdev soon.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver gets rss information from the last descriptor of the packet.
When driver handle the rss type, ring->next_to_clean indicates the
first descriptor of next packet.
This patch fix the descriptor index with "ring->next_to_clean - 1".
Fixes: 232fc64b6e ("net: hns3: Add HW RSS hash information to RX skb")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user disables flow director, all the rules will be disabled. But
when reset happens, it will restore all the rules again. It's not
reasonable. This patch fixes it by add flow director status check before
restore fules.
Fixes: 6871af29b3 ("net: hns3: Add reset handle for flow director")
Fixes: c17852a893 ("net: hns3: Add support for enable/disable flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When add flow director fule for vf, the vf id is used as array
subscript before valid checking, which may cause memory overflow.
Fixes: dd74f815dd ("net: hns3: Add support for rule add/delete for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing DOWN operation, the driver will reclaim the memory which has
already used for TX. If the hardware is processing this memory, it will
cause a RCB error to the hardware. According the hardware's description,
the driver should reset the tqp before reclaim the memory during DOWN.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each pf supports max 64 vectors and 128 tqps. For 2p/4p core scenario,
there may be more than 64 cpus online. So the result of min_t(u16,
num_Online_cpus(), tqp_num) may be more than 64. This patch adds check
for the vector number.
Fixes: dd38c72604 ("net: hns3: fix for coalesce configuration lost during reset")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udelay() in driver may always occupancy processor. If there is only
one cpu in system, the VF driver may initialize fail when insmod
PF and VF driver in the same system. This patch use msleep() to free
cpu when VF wait PF message.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In original codes, default tc value is set to the max tc. It's more
reasonable to close tc by changing default tc value to 1. Users can
enable it with lldp tool when they want to use tc.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When triggering nic down, there is a time window between bringing down
the protocol stack and stopping the work task. If the net is up in the
time window, it may bring up the protocol stack again.
This patch fixes it by stop the work task at the beginning of
hns3_nic_net_stop(). To keep symmetrical, start the work task at the
end of hns3_nic_net_open().
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/wil6210/main.c: In function '_wil6210_disconnect':
drivers/net/wireless/ath/wil6210/main.c:407:23: warning:
variable 'wdev' set but not used [-Wunused-but-set-variable]
It never used since commit ("e1b43407c034 wil6210: refactor disconnect flow")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is not an unexpected condition, so we don't need to be shouting to the
world about it.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When ath6kl was reworked to share code between regular and scheduled scans
in commit 3b8ffc6a22 ("ath6kl: Configure probed SSID list consistently"),
probed SSID entry changed from 1-index to 0-indexed. However,
ath6kl_cfg80211_scan_complete_event() was missed in that change. Fix its
indexing so that we correctly clear out the probed SSID list.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit dd45b7598f ("ath6kl: Include match ssid list in scheduled scan")
merged the probed and matched SSID lists before sending them to the
firmware. In the process, it assumed match set support is always available
in ath6kl_set_probed_ssids, which breaks scans for hidden SSIDs. Now, check
that the firmware supports matching SSIDs in scheduled scans before setting
MATCH_SSID_FLAG.
Fixes: dd45b7598f ("ath6kl: Include match ssid list in scheduled scan")
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a break at the end of the ini tlv case.
Fix both the internal and external tlv parsing.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bump the API version to 43 for 9000 and 22000 devices.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add debug data to the warning issued when getting wrong region
id from firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in debug message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is needed to test TWT requester on the client side.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These macros are never used and are actually wrong, so it's very
confusing. Remove them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the rt status of the last assert or 0 if the dump collection was
not initiated by an assert. Add the number of rx and tx fifos in use.
These fields are added to dump info lst file.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes, due to SCD bug, we need to start the queue with an
higher SSN. The queue allocation function currently increments
the SSN in the packet itself, but it is pointless, since this
value is overridden later by iwl_mvm_tx_mpdu with the value
from mvmsta->tid_data[tid].seq_number. Updating tid data is
sufficient.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In reclaim code, we don't need to take the queue lock for
waking the queue. The code section is executed only when
the tx path is stopped, and since the reclaim path is not
executed in parallel to itself, no one can update the queue
pointers, and accessing them is safe without a lock.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need to lock mvm station for transport reclaim.
Move the locking down, after the reclaim.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handle RX no data notification, which is used for advertising NDP to
radiotap.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HE capabilities differ between AP and STA.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's not the iwlwifi module that depends on mac80211, but iwlmvm and
iwldvm. To reflect this better, make MVM and DVM Kconfig options
depend on MAC80211 instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FW expects to get the ppe value for each NSS-BW pair in the same
format as in the he phy capabilities IE, which means that a value of 0
implies ppe should be used for BPSK (mcs 0). If there are no PPE
thresholds in the IE, or if for some NSS-RU pair there's no threshold
set for it (this could happen because it's a variable-sized field), it
means no PPE should not be used for that pair, so the value sent to FW
should be 7 which corresponds to "none".
Fixes: 514c30696f ("iwlwifi: add support for IEEE802.11ax")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make the coupling of station id and queue id clear. Group code
together. Remove outdated comment. Never use an undefined hw
queue as given from mac80211.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Assigning mvmsta to be NULL when we are about to exit the
function is pointless. Remove it. Move the variable declaration
to the scope it is used.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In iwl_mvm_tx_skb_non_sta(), in case of managed interface,
the AP station was supposed to be used for multicast frames
instead of the auxiliary station to avoid frames possibly
sent to an absent P2P GO. However, when moving to DQA mode,
this was broken as no valid queue was assigned. This is fixed
by a recent patch that directs all non-offchannel traffic to
ap station earlier in the TX path. However, the broken, and
now dead code, remained. Remove it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When building AMSDU for gen2, code uses iwl_tx_cmd. The only
updated field is len, which is in the same location, so it
is not a bug. However, it is a bit confusing and error prone,
so change it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function cw1200_bss_info_changed() and cw1200_hw_scan() can be
concurrently executed.
The two functions both access a possible shared variable "frame.skb".
This shared variable is freed by dev_kfree_skb() in cw1200_upload_beacon(),
which is called by cw1200_bss_info_changed(). The free operation is
protected by a mutex lock "priv->conf_mutex" in cw1200_bss_info_changed().
In cw1200_hw_scan(), this shared variable is accessed without the
protection of the mutex lock "priv->conf_mutex".
Thus, concurrency use-after-free bugs may occur.
To fix these bugs, the original calls to mutex_lock(&priv->conf_mutex) and
mutex_unlock(&priv->conf_mutex) are moved to the places, which can
protect the accesses to the shared variable.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 1204aa17f3 ("brcmfmac: set WIPHY_FLAG_HAVE_AP_SME flag")
the Raspberry Pi 3 A+ (BCM43455) isn't able to operate in AP mode with
hostapd (device_ap_sme=1 use_monitor=0):
brcmfmac: brcmf_cfg80211_stop_ap: setting AP mode failed -52
So add the missing mgmt_stypes for AP mode to fix this.
Fixes: 1204aa17f3 ("brcmfmac: set WIPHY_FLAG_HAVE_AP_SME flag")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the update_connect_param callback is set, nl80211 expects the flag
WIPHY_FLAG_SUPPORTS_FW_ROAM to be set as well. However, this flag is
only set when modparam roamoff=0, while the callback is set
unconditionally. Since commit 7f9a3e150e this causes a warning in
wiphy_register, which breaks brcmfmac.
Disable the update_connect_param callback when roamoff=0 to fix this.
Fixes: 7f9a3e150e ("nl80211: Update ERP info using NL80211_CMD_UPDATE_CONNECT_PARAMS")
Cc: Stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 6320 family of switches uses the same watchdog registers as the
6390.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_phylink_validate() sets all modes that are supported by a
given PPv2 port. An mistake made the 10000baseT_Full mode being
advertised in some cases when a port wasn't configured to perform at
10G. This patch fixes this.
Fixes: d97c9f4ab0 ("net: mvpp2: 1000baseX support")
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. remove fine-tune property and related setting to simplify
the timing adjustment flow.
2. set timing value according to the value from device tree,
and will not care whether PHY insert internal delay.
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC Reset was noticed to erase important EEPROM settings.
It is also unnecessary since a chip wide reset was done earlier
in initialization, and that reset preserves EEPROM settings.
There for this patch removes the unnecessary MAC specific reset.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expression terminated with "," instead of ";", resulted in
set_fte getting bad value for modify_enable_mask field.
Fixes: bd5251dbf1 ("net/mlx5_core: Introduce flow steering destination of type counter")
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the completion queue of the RQ is empty, do not immediately return.
If left-over decompressed CQEs (from the previous cycle) were processed,
need to go to the finalization part of the poll function.
Bug exists only when CQE compression is turned ON.
This solves the following issue:
mlx5_core 0000:82:00.1: mlx5_eq_int:544:(pid 0): CQ error on CQN 0xc08, syndrome 0x1
mlx5_core 0000:82:00.1 p4p2: mlx5e_cq_error_event: cqn=0x000c08 event=0x04
Fixes: 4b7dfc9925 ("net/mlx5e: Early-return on empty completion queues")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Previous patches tried to make RIF deletion more robust and avoid
use-after-free situations.
As another precaution, hold a reference on a RIF's netdev and release it
when the RIF is deleted.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the past we had multiple instances where RIFs were not properly
deleted.
One of the reasons for leaking a RIF was that at the time when IP
addresses were flushed from the respective netdev (prompting the
destruction of the RIF), the netdev was no longer a mlxsw upper. This
caused the inet{,6}addr notification blocks to ignore the NETDEV_DOWN
event and leak the RIF.
Instead of checking whether the netdev is our upper when an IP address
is removed, we can instead check if the netdev has a RIF configured.
To look up a RIF we need to access mlxsw private data, so the patch
stores the notification blocks inside a mlxsw struct. This then allows
us to use container_of() and extract the required private data.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next patch is going to make RIF deletion more robust by removing
reliance on fragile mlxsw_sp_lower_get(). This is because a netdev is
not necessarily our upper anymore when its IP addresses are flushed.
The inet{,6}addr notification blocks are going to resolve 'struct
mlxsw_sp' using container_of(), but the functions they call still use
mlxsw_sp_lower_get().
As a preparation for the next patch, propagate 'struct mlxsw_sp' down to
the functions called from the notification blocks and remove reliance on
mlxsw_sp_lower_get().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a LAG device or a VLAN device on top of it is enslaved to a bridge,
the driver propagates the CHANGEUPPER event to the LAG's slaves.
This causes each physical port to increase the reference count of the
internal representation of the bridge port by calling
mlxsw_sp_port_bridge_join().
However, when a port is removed from a LAG, the corresponding leave()
function is not called and the reference count is not decremented. This
leads to ugly hacks such as mlxsw_sp_bridge_port_should_destroy() that
try to understand if the bridge port should be destroyed even when its
reference count is not 0.
Instead, make sure that when a port is unlinked from a LAG it would see
the same events as if the LAG (or its uppers) were unlinked from a
bridge.
The above is achieved by walking the LAG's uppers when a port is
unlinked and calling mlxsw_sp_port_bridge_leave() for each upper that is
enslaved to a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b3529af6bb ("spectrum: Reference count VLAN entries") started
reference counting port-VLAN entries in a similar fashion to the 8021q
driver.
However, this is not actually needed and only complicates things.
Instead, the driver should forbid the creation of a VLAN on a port if
this VLAN already exists. This would also solve the issue fixed by the
mentioned commit.
Therefore, remove the get()/put() API and use create()/destroy()
instead.
One place that needs special attention is VLAN addition in a VLAN-aware
bridge via switchdev operations. In case the VLAN flags (e.g., 'pvid')
are toggled, then the VLAN entry already exists. To prevent the driver
from wrongly returning EEXIST, the driver is changed to check in the
prepare phase whether the entry already exists and only returns an error
in case it is not associated with the correct bridge port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 993107fea5 ("mlxsw: spectrum_switchdev: Fix VLAN device
deletion via ioctl") I fixed a bug caused by the fact that the driver
views differently the deletion of a VLAN device when it is deleted via
an ioctl and netlink.
Instead of relying on a specific order of events (device being
unregistered vs. VLAN filter being updated), simply make sure that the
driver performs the necessary cleanup when the VLAN device is unlinked,
which always happens before the other two events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is no longer used. Remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when a RIF is constructed on top of a FID, the RIF increments
the FID's reference count and the RIF is destroyed when the FID's
reference count drops to 1. This effectively means that when no local
ports are member in the FID, the FID is destroyed regardless if the
router port is a member in the FID or not.
The above can lead to the unexpected behavior in which routes using a
VLAN interface as their nexthop device are no longer offloaded after the
last local port leaves the corresponding VLAN (FID).
Example:
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1 offload
# bridge vlan del vid 10 dev swp3
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1
After the patch, the route is offloaded before and after the VLAN is
removed from local port 'swp3', as the RIF corresponding to 'br0.10'
continues to exists.
In order to remove RIFs' reliance on the underlying FID's reference
count, we need to add a reference count to sub-port RIFs, which are RIFs
that correspond to physical ports and their uppers (e.g., LAG devices).
In this case, each {Port, VID} ('struct mlxsw_sp_port_vlan') needs to
hold a reference on the RIF. For example:
bond0.10
|
bond0
|
+-------+
| |
swp1 swp2
Both {Port 1, VID 10} and {Port 2, VID 10} will hold a reference on the
RIF corresponding to 'bond0.10'. When the last reference is dropped, the
RIF will be destroyed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, only VRF and macvlan uppers are supported on top of VLAN
device configured over a bridge, so make sure the driver forbids other
uppers.
Note that enslavement to a VRF is handled earlier in the notification
block, so there is no need to check for a VRF upper here.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code has 2 problems. It assumes that the RX ring for
the loopback packet is combined with the TX ring. This is not
true if the ethtool channels are set to non-combined mode. The
second problem is that it won't work on 57500 chips without
adjusting the logic to get the proper completion ring (cpr) pointer.
Fix both issues by locating the proper cpr pointer through the RX
ring.
Fixes: e44758b78a ("bnxt_en: Use bnxt_cp_ring_info struct pointer as parameter for RX path.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
secpath_set is a wrapper for secpath_dup that will not perform
an allocation if the secpath attached to the skb has a reference count
of one, i.e., it doesn't need to be COW'ed.
Also, secpath_dup doesn't attach the secpath to the skb, it leaves
this to the caller.
Use secpath_set in places that immediately assign the return value to
skb.
This allows to remove skb->sp without touching these spots again.
secpath_dup can eventually be removed in followup patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
... so this won't have to be changed when skb->sp goes away.
v2: no changes, preserve ack.
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will avoid touching this when sp pointer is removed from sk_buff struct.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_sec_path and secpath_exists helpers where possible.
This reduces noise in followup patch that removes skb->sp pointer.
v2: no changes, preseve acks from v1.
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics for pending frames in Rx/Tx conf FQs and
number of buffers in pool. Available through ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last set of fixes for 4.20. All (except the mt76 fix) of these are
important fixes to user reported problems and pretty small in size.
rtlwifi
* fix skb leak
mwifiex
* revert a commit from v4.19 due to problems with locking
mt76
* fix a potential NULL derenfence
* add entry to MAINTAINERS
iwlwifi
* fix a firmware crash which was a regression introduced in v4.20-rc4
ath10k
* fix a firmware crash with wcn3990 firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcGlNvAAoJEG4XJFUm622boJ0H/AjDASkdxSG4n+s1wCmsUizE
jK9YwS2dOc1oVSzGPm35GccFgkc4x1IpS1qoTo1rykVD7Cn6G7mj6eqy8vTiJ24S
6HPhdkS5YynWvYfbQmuhhhaQ6ew8/dJzqhPJAH1/kPfDsy08qUaVl5tGw4CwP4Pp
Ufvrn8VNmRbrAg9Jq28+xmANNURtKNtHmXI5WWuSvA4LzkdEz2aebG8ynOwTrVW6
f6NHTDeJ5tWrswr0EWGjBbGRfb8TlacOxqzytrFYFuYHH3WiqCQZdsvRBazvryqJ
szrYMlI+bSN4m3ZEAtEWlZYTU1YNPwbRDXc+GYkbDr19YKevHxi+46SvXa36cJM=
=ECaW
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.20
Last set of fixes for 4.20. All (except the mt76 fix) of these are
important fixes to user reported problems and pretty small in size.
rtlwifi
* fix skb leak
mwifiex
* revert a commit from v4.19 due to problems with locking
mt76
* fix a potential NULL derenfence
* add entry to MAINTAINERS
iwlwifi
* fix a firmware crash which was a regression introduced in v4.20-rc4
ath10k
* fix a firmware crash with wcn3990 firmware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
-----BEGIN PGP SIGNATURE-----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=EpyK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have too many changes to list, highlights:
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HL2.0 firmware does not support setting quiet mode. If the host driver sends
the quiet mode setting command to the HL2.0 firmware, it crashes with the below
signature.
fatal error received: err_qdi.c:456:EX:wlan_process:1:WLAN RT:207a:PC=b001b4f0
The quiet mode command support is exposed by the firmware via thermal throttle
wmi service. Enable ath10k thermal support if thermal throttle wmi service bit
is set. 10.x firmware versions support this feature by default, but
unfortunately do not advertise the support via service flags, hence have to
manually set the service flag in ath10k_core_compat_services().
Tested on QCA988X with 10.2.4.70.9-2. Also tested on WCN3990.
Co-developed-by: Govind Singh <govinds@codeaurora.org>
Co-developed-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After phy_start() phylib takes care of all needed actions, including
aneg settings and checking link state. There's no need to set state
PHY_CHANGELINK in drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently variable data0 is not being initialized so a garbage value is
being passed to vxge_hw_vpath_fw_api and this value is being written to
the rts_access_steer_data0 register. There are other occurrances where
data0 is being initialized to zero (e.g. in function
vxge_hw_upgrade_read_version) so I think it makes sense to ensure data0
is initialized likewise to 0.
Detected by CoverityScan, CID#140696 ("Uninitialized scalar variable")
Fixes: 8424e00dfd ("vxge: serialize access to steering control register")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least old Xen net backends seem to send frags with no real data
sometimes. In case such a fragment happens to occur with the frag limit
already reached the frontend will BUG currently even if this situation
is easily recoverable.
Modify the BUG_ON() condition accordingly.
Tested-by: Dietmar Hahn <dietmar.hahn@ts.fujitsu.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff5 ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current state for the lan78xx driver does not allow for changing the
MAC address of the interface, without either removing the module (if
you compiled it that way) or rebooting the machine. If you attempt to
change the MAC address, ifconfig will show the new address, however,
the system/interface will not respond to any traffic using that
configuration. A few short-term options to work around this are to
unload the module and reload it with the new MAC address, change the
interface to "promisc", or reboot with the correct configuration to
change the MAC.
This patch enables the ability to change the MAC address via fairly normal means...
ifdown <interface>
modify entry in /etc/network/interfaces OR a similar method
ifup <interface>
Then test via any network communication, such as ICMP requests to gateway.
My only test platform for this patch has been a raspberry pi model 3b+.
Signed-off-by: Jason Martinsen <jasonmartinsen@msn.com>
-----
Signed-off-by: David S. Miller <davem@davemloft.net>
3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN7431 uses an external phy, and it can be found anywhere in
the phy address space. This patch uses phy address 1 for LAN7430
only. And searches all addresses otherwise.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default remotes are stored as FDB entries with an Ethernet address of
00:00:00:00:00:00. When a request is made to change a remote address of
a VXLAN device, vxlan_changelink() first deletes the existing default
remote, and then creates a new FDB entry.
This works well as long as the list of default remotes matches exactly
the configuration of a VXLAN remote address. Thus when the VXLAN device
has a remote of X, there should be exactly one default remote FDB entry
X. If the VXLAN device has no remote address, there should be no such
entry.
Besides using "ip link set", it is possible to manipulate the list of
default remotes by using the "bridge fdb". It is therefore easy to break
the above condition. Under such circumstances, the __vxlan_fdb_delete()
call doesn't delete the FDB entry itself, but just one remote. The
following vxlan_fdb_create() then creates a new FDB entry, leading to a
situation where two entries exist for the address 00:00:00:00:00:00,
each with a different subset of default remotes.
An even more obvious breakage rooted in the same cause can be observed
when a remote address is configured for a VXLAN device that did not have
one before. In that case vxlan_changelink() doesn't remove any remote,
and just creates a new FDB entry for the new address:
$ ip link add name vx up type vxlan id 2000 dstport 4789
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.20 self permanent
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.30 self permanent
$ ip link set dev vx type vxlan remote 192.0.2.30
$ bridge fdb sh dev vx | grep 00:00:00:00:00:00
00:00:00:00:00:00 dst 192.0.2.30 self permanent <- new entry, 1 rdst
00:00:00:00:00:00 dst 192.0.2.20 self permanent <- orig. entry, 2 rdsts
00:00:00:00:00:00 dst 192.0.2.30 self permanent
To fix this, instead of calling vxlan_fdb_create() directly, defer to
vxlan_fdb_update(). That has logic to handle the duplicates properly.
Additionally, it also handles notifications, so drop that call from
changelink as well.
Fixes: 0241b83673 ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a failure occurs in rtnl_configure_link(), the current code
calls unregister_netdevice() to roll back the earlier call to
register_netdevice(), and jumps to errout, which calls
vxlan_fdb_destroy().
However unregister_netdevice() calls transitively ndo_uninit, which is
vxlan_uninit(), and that already takes care of deleting the default FDB
entry by calling vxlan_fdb_delete_default(). Since the entry added
earlier in __vxlan_dev_create() is exactly the default entry, the
cleanup code in the errout block always leads to double free and thus a
panic.
Besides, since vxlan_fdb_delete_default() always destroys the FDB entry
with notification enabled, the deletion of the default entry is notified
even before the addition was notified.
Instead, move the unregister_netdevice() call after the manual destroy,
which solves both problems.
Fixes: 0241b83673 ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rdst of an offloaded FDB entry is replaced, it certainly isn't
offloaded anymore. Drivers are notified about such replacements, and can
re-mark the entry as offloaded again if they so wish. However until a
driver does so explicitly, assume a replaced FDB entry is not offloaded.
Note that replaces coming via vxlan_fdb_external_learn_add() are always
immediately followed by an explicit offload marking.
Fixes: 0efe117333 ("vxlan: Support marking RDSTs as offloaded")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
This series is essentially a cleanup to align with the rest of the NIC
switchdev drivers and make us
more robust and clear/n: currently the PF netdev serves as the mlx5
e-switch uplink netdev
representor when going into switchdev mode and back as plain NIC
netdev when going out.
This causes some irregularities and misc troubles.
Move to use dedicated uplink rep, as we have for the VF vports.
The uplink rep netdev does has sysfs link and supports the sriov vf
mac ndo, these two are in
use by libvirt and other orchestrators, It also has richer ethtool
support to allow controlling the
port link & mtu along with supporting dcb and plugging into the mlx5
lag logic.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcF/MBAAoJEEg/ir3gV/o+apkIAKVeB/ha8qiY+9ntA9B8HVxO
cYb+fv4+DuYjTg/nN5QdYSAisN4SwFDA5ukz/ckr6XwV65EgTjAtlon/fHg/rDyz
YT3dJRP9yjNXKxRvxa0K4PmTasmXGXzaJzsXYemHsfCDdnkNknZsqA+yoNe+2c40
HoNsdy/Pvr18PjzYtpX0BiuSjH623daBmdFH0o+rwuwsApkAUlBJfosTg/7xyU7v
TAjy8S1HCloJ7OAjOlzXVmYr65sAlQoFr860vLDQ7Og7JemxjSXQ+AdNb6mSAvZ5
LBEvCA3G5tb4OkFX+1i/alxOcuG8/FoO+O3ZQWve1DNxoS76po851bgHXIdZCPg=
=pqTq
-----END PGP SIGNATURE-----
Merge tag 'mlx5-uplink-rep-2018-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed:
====================
mlx5-uplink-rep-2018-12-15
Or Gerlitz says:
This series is essentially a cleanup to align with the rest of the NIC
switchdev drivers and make us
more robust and clear/n: currently the PF netdev serves as the mlx5
e-switch uplink netdev
representor when going into switchdev mode and back as plain NIC
netdev when going out.
This causes some irregularities and misc troubles.
Move to use dedicated uplink rep, as we have for the VF vports.
The uplink rep netdev does has sysfs link and supports the sriov vf
mac ndo, these two are in
use by libvirt and other orchestrators, It also has richer ethtool
support to allow controlling the
port link & mtu along with supporting dcb and plugging into the mlx5
lag logic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.
Specifically:
- TX timestamp descriptors may be loaded before ctrl is loaded for the
TX_USED check, which is racy as the descriptors may be updated between
the loads, causing old timestamp descriptor data to be used.
- RX ctrl may be loaded before addr is loaded for the RX_USED check,
which is racy as a new frame may be written between the loads, causing
old ctrl descriptor data to be used.
This issue exists for both macb_rx() and gem_rx() variants.
Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().
I have not observed any actual problems in practice caused by these
being missing, though.
Tested on a ZynqMP based system.
Fixes: 89e5785fc8 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit RX_USED set to 0 in the address field allows the controller to write
data to the receive buffer descriptor.
The driver does not ensure the ctrl field is ready (cleared) when the
controller sees the RX_USED=0 written by the driver. The ctrl field might
only be cleared after the controller has already updated it according to
a newly received frame, causing the frame to be discarded in gem_rx() due
to unexpected ctrl field contents.
A message is logged when the above scenario occurs:
macb ff0b0000.ethernet eth0: not whole frame pointed by descriptor
Fix the issue by ensuring that when the controller sees RX_USED=0 the
ctrl field is already cleared.
This issue was observed on a ZynqMP based system.
Fixes: 4df95131ea ("net/macb: change RX path for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
64-bit DMA addresses are split in upper and lower halves that are
written in separate fields on GEM. For RX, bit 0 of the address is used
as the ownership bit (RX_USED). When the RX_USED bit is unset the
controller is allowed to write data to the buffer.
The driver does not guarantee that the controller already sees the upper
half when the RX_USED bit is cleared, possibly resulting in the
controller writing an incoming frame to an address with an incorrect
upper half and therefore possibly corrupting unrelated system memory.
Fix that by adding the necessary DMA memory barrier between the writes.
This corruption was observed on a ZynqMP based system.
Fixes: fff8019a08 ("net: macb: Add 64 bit addressing support for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Acked-by: Harini Katakam <harini.katakam@xilinx.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms (currently detected only on SAMA5D4) TX might stuck
even the pachets are still present in DMA memories and TX start was
issued for them. This happens due to race condition between MACB driver
updating next TX buffer descriptor to be used and IP reading the same
descriptor. In such a case, the "TX USED BIT READ" interrupt is asserted.
GEM/MACB user guide specifies that if a "TX USED BIT READ" interrupt
is asserted TX must be restarted. Restart TX if used bit is read and
packets are present in software TX queue. Packets are removed from software
TX queue if TX was successful for them (see macb_tx_interrupt()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1070:5: warning:
variable 'op' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1342:5: warning:
variable 'cmd_op' set but not used [-Wunused-but-set-variable]
'op' never used since introduction in commit 7cb03b2347 ("qlcnic:
Support VF-PF communication channel commands.")
'cmd_op' not used since commit 6226204bcf ("qlcnic: Fix operation
type and command type.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function should return an error if create_singlethread_workqueue()
fails.
Fixes: 34877a15f7 ("net: stmmac: Rework and fix TX Timeout code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally deleted the code to set "rc = -ENOMEM;" and this patch
adds it back.
Fixes: d2201a2159 ("qed: No need for LL2 frags indication")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far phy_error() silently stops the PHY state machine. If the network
driver doesn't inform about a MDIO error then the user may wonder why
his network is down. Let's print the stack trace to facilitate search
for the root cause of the error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers phy_is_started() and __phy_is_started() to avoid open-coded
checks whether PHY has been started. To make the check easier move
PHY_HALTED before PHY_UP in enum phy_state. Further improvements:
phy_start_aneg():
Return -EBUSY and print warning if function is called from a non-started
state (DOWN, READY, HALTED). Better check because function is exported
and drivers may use it incorrectly.
phy_interrupt():
Return IRQ_NONE also if state is DOWN or READY. We should never receive
an interrupt in one of these states, but better play safe.
phy_stop():
Just return and print a warning if PHY is in a non-started state.
This warning should help to identify drivers with unbalanced calls to
phy_start() / phy_stop().
phy_state_machine():
Schedule state machine run only if PHY is in a started state.
E.g. if state is READY we don't need the state machine, it will be
started by phy_start().
v2:
- don't use __func__ within phy_warn_state
v3:
- use WARN() instead of printing error message to facilitate debugging
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a workaround to restart the phylib state machine in case of a
MDIO access timeout. Seems it was introduced to deal with the
consequences of a too small MDIO timeout. See also commit message of
c3b084c24c ("net: fec: Adjust ENET MDIO timeouts") which increased
the timeout value later. Due to the later timeout value fix it seems
to be safe to remove the workaround.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two statements that are indented too much by one space each,
fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_phylink_validate() function sets all modes that are
supported by a given PPv2 port. A recent change made all ports to
advertise they support 10G modes in certain cases. This is not true,
as only the port #0 can do so. This patch fixes it.
Fixes: 01b3fd5ac9 ("net: mvpp2: fix detection of 10G SFP modules")
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When caculating the SSU buffer, it first allocate tx and
rx private buffer, then the remaining buffer is for rx
shared buffer. The remaining buffer size should be at
least bigger than or equal to the shared_std, which is the
minimum shared buffer size required by the driver, but
currently if the remaining buffer size is equal to the
shared_std, it returns failure, which causes SSU buffer
allocation failure problem.
This patch fixes this problem by rounding up shared_std before
checking the the remaining buffer size bigger than or equal to
the shared_std.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware expects the buffer size set to SSU is aligned to
256 bytes, this patch aligns the buffer size to 256 byte using
roundup or rounddown function.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of getting tx and dv buffer size through
firmware, because different version of hardware requires different
size of tx and dv buffer.
This patch also add dv_buf_size to tc' private buffer size even if
pfc is not enable for the tc.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver calls phy_connect_direct and registers hclge_mac_adjust_link
to synchronize mac speed and duplex from phy. It is better to
synchronize mac speed and duplex from phy when phy link up.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our phy does not support 1000M/half, this patch removes 1000M/half from
PHY_SUPPORTED_FEATURES.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
coalesce param updates every 100 napi times, it may update a little
late if ping test after a high rate flow, may over napi poll is called
100 times as ping test sends packets every second.
This patch updates coalesce param every second, instead with every
100 napi times. It can not update the param 100% in time, but the
lag time is very short.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hns3_nic_uninit_vector_data(), the procedure of uninitializing
the tqp_vector's IRQ has not set affinity_notify to NULL and changes
its init flag. This patch fixes it. And for simplificaton, local
variable tqp_vector is used instead of priv->tqp_vector[i].
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reset, it is unnecessary to get the hardware's default
configuration again, otherwise, the user's configuration will be
overwritten.
Fixes: 4ed340ab8f ("net: hns3: Add reset process in hclge_main")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclge_reset() completes successfully, it should update the
last_reset_time, set reset_fail_cnt to 0, and set reset_type of
hnae3_ae_dev to HNAE3_NONE_RESET.
Also when hclgevf_reset() completes successfully, it should update
the last_reset_time, and set reset_type of hnae3_ae_dev to
HNAE3_NONE_RESET.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing DOWN, the calling of napi_disable() may not return, since the
napi_complete() in the hns3_nic_common_poll() will never be called when
HNS3_NIC_STATE_DOWN is set. So we need to call napi_complete() before
checking HNS3_NIC_STETE_DOWN.
Fixes: ff0699e04b ("net: hns3: stop napi polling when HNS3_NIC_STATE_DOWN is set")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hclgevf_pci_reset(), it only uninitialize and initialize
the msi, so if the initialization fails, hclgevf_uninit_hdev()
does not need to uninitialize the msi, but needs to uninitialize
the pci, otherwise it will cause pci resource not free.
Fixes: 862d969a3a ("net: hns3: do VF's pci re-initialization while PF doing FLR")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_get_vector_ring_chain() failed in the
hns3_nic_init_vector_data(), it should do the error handling instead
of return directly.
Also, cur_chain should be freed instead of chain and head->next should
be set to NULL in error handling of hns3_get_vector_ring_chain.
This patch fixes them.
Fixes: 73b907a083 ("net: hns3: bugfix for buffer not free problem during resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a packet was decapsulated it is classified to the relevant FID
based on its VNI and undergoes L2 forwarding.
Unlike regular (non-encapsulated) ARP packets, Spectrum does not trap
decapsulated ARP packets during L2 forwarding and instead can only trap
such packets in the underlay router during decapsulation.
Add this missing packet trap, which is required for VXLAN routing when
the MAC of the target host is not known.
Fixes: b02597d513 ("mlxsw: spectrum: Add NVE packet traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the firmware flash process, some of the EMADs get timed out, which
causes the driver to send them again with a limit of 5 retries. There are
some situations in which 5 retries is not enough and the EMAD access fails.
If the failed EMAD was related to the flashing process, the driver fails
the flashing.
The reason for these timeouts during firmware flashing is cache misses in
the CPU running the firmware. In case the CPU needs to fetch instructions
from the flash when a firmware is flashed, it needs to wait for the
flashing to complete. Since flashing takes time, it is possible for pending
EMADs to timeout.
Fix by increasing EMADs' timeout while flashing firmware.
Fixes: ce6ef68f43 ("mlxsw: spectrum: Implement the ethtool flash_device callback")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved setting if_combination.num_different_channels/radar_detect_widths
into an else after use_chanctx. In the case of use_chanctx, these two
settings were getting overwritten.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously the identifier used for indirect block callback registry and
for block rule cb registry (when done via indirect blocks) was the pointer
to the netdev we were interested in receiving updates on. This worked fine
if a single app existed that registered one callback per netdev of
interest. However, if multiple cards are in place and, in turn, multiple
apps, then each app may register the same callback with the same
identifier to both the netdev's indirect block cb list and to a block's cb
list. This can lead to EEXIST errors and/or incorrect cb deletions.
Prevent this conflict by using the app pointer as the identifier for
netdev indirect block cb registry, allowing each app to register a unique
callback per netdev. For block cb registry, the same app may register
multiple cbs to the same block if using TC shared blocks. Instead of the
app, use the pointer to the allocated cb_priv data as the identifier here.
This means that there can be a unique block callback for each app/netdev
combo.
Fixes: 3166dd07a9 ("nfp: flower: offload tunnel decap rules via indirect TC blocks")
Reported-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ethtool_regs version is set to 0 for all DSA drivers.
Use this field to store the chip ID to simplify the pretty dump of
any interfaces registered by the "dsa" driver.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With autoneg enabled, PHY loopback test fails. To disable autoneg,
driver needs to send a valid forced speed to FW. FW is not sending
async event for invalid speeds. To fix this, query forced speeds
and send the correct speed when disabling autoneg mode.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port statistics which include RDMA counters are useful even when the
netdevice is down. Do not free the port statistics DMA buffers
when the netdevice is down. This is keep the snapshot of the port
statistics and counters will just continue counting when the
netdevice goes back up.
Split the bnxt_free_stats() function into 2 functions. The port
statistics buffers will only be freed when the netdevice is
removed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the current driver, the statistics reported by .ndo_get_stats64()
are reset when the device goes down. Store a snapshot of the
rtnl_link_stats64 before shutdown. This snapshot is added to the
current counters in .ndo_get_stats64() so that the counters will not
get reset when the device is down.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently firmware specific errors are returned directly in flash_device
and reset ethtool hooks. Modify it to return linux standard errors
to userspace when flashing operations fail.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the code allows ETS bandwidth weight 0 to be set on unused TCs.
We should not set any DCB parameters on unused TCs at all.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Display the CoS counters as additional priority counters by looking up
the priority to CoS queue mapping. If the TX extended port statistics
block size returned by firmware is big enough to cover the CoS counters,
then we will display the new priority counters. We call firmware to get
the up-to-date pri2cos mapping to convert the CoS counters to
priority counters.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some minor differences when assigning VF resources on the
new chips. The MSIX (NQ) resource has to be assigned and ring group
is not needed on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bringing up a device, the code checks to see if the number of
MSIX has changed. pci_disable_msix() should be called first before
changing the number of reserved NQs/CMPL rings. This ensures that
the MSIX vectors associated with the NQs/CMPL rings are still
properly mapped when pci_disable_msix() masks the vectors.
This patch will prevent errors when RDMA support is added for the new
57500 chips. When the RDMA driver shuts down, the number of NQs is
decreased and we must use the new sequence to prevent MSIX errors.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_en requires same number of stat_ctxs as CP rings but RDMA
requires only 1 stat_ctx. Also add a new parameter resv_stat_ctxs
to better keep track of stat_ctxs reserved including resources used
by RDMA. Add a stat_ctxs parameter to all the relevant resource
reservation functions so we can reserve the correct number of
stat_ctxs.
Prior to this patch, we were not reserving the extra stat_ctx for
RDMA and RDMA would not work on the new 57500 chips.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling bnxt_set_max_func_stat_ctxs() to modify max stat_ctxs requested
or freed by the RDMA driver is wrong. After introducing reservation of
resources recently, the driver has to keep track of all stat_ctxs
including the ones used by the RDMA driver. This will provide a better
foundation for accurate accounting of the stat_ctxs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For bnxt_en driver, stat_ctxs created will always be same as
cp_nr_rings. Remove extra variable that duplicates the value.
Also introduce bnxt_get_avail_stat_ctxs_for_en() helper to get
available stat_ctxs and bnxt_get_ulp_stat_ctxs() helper to return
number of stat_ctxs used by RDMA.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The available CP rings are calculated differently on the new 57500
chips, so add this helper to do this calculation correctly. The
VFs will be assigned these available CP rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF has a pool of NQs and MSIX vectors assigned to it based on
NVRAM configurations. The number of usable MSIX vectors on the PF
is the minimum of the NQs and MSIX vectors. Any excess NQs without
associated MSIX may be used for the VFs, so we need to store this
max_nqs value. max_nqs minus the NQs used by the PF will be the
available NQs for the VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The failure to create debugfs entry is unpleasant event, but not enough
to abort drier initialization. Align the mlx5_core code to debugfs design
and continue execution whenever debugfs_create_dir() successes or not.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to control carrier from /sys/class/net/ethX/carrier
for Fixed PHYs.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers can use this as .ndo_change_carrier() to change carrier
via /sys/class/net/ethX/carrier.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kzalloc_node(..., GFP_KERNEL, node) will attempt to allocate
memory as close as possible to the node.
There is no need to fallback to kzalloc() if this has failed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the ethtool entries to control the port should be supported by
the uplink rep netdev in switchdev mode, add them.
While here, add also the get/set coalesce entries for all reps.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Towards supporting set/get of global pause for the port
and get of the port link ksetting from the uplink representor,
expose the relevant entries to other mlx5 callers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Some of the sriov ndo calls are needed also on the switchdev mode -
e.g setup VF mac and reading vport stats. Add them to the uplink rep
netdev ops. Same for the UDP tunnel ones, need them there to identify
offloaded udp tunnel ports.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Take care of setup/teardown for the port link, dcb, lag as well as
dealing with port mtu and carrier for e-switch uplink representors.
This is achieved by adding a dedicated profile instance for uplink
representors which includes the enable/disable and more profile routines
which are invoked by the general mlx5e code for netdev attach/detach.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Now, when we have a dedicated uplink representor, the netdev instance
set over the esw manager vport (PF) is of no-use. As such, remove it
once we're on switchdev mode and get it back to life when off switchdev.
This is done by reloading the Ethernet interface as well (we already
do that for the IB interface) from the eswitch code while going in/out
of switchdev mode.
The Eth add/remove entries are modified to act differently when called in
switchdev mode. In this case we only deal with registration of the eth
vport representors. The rep netdevices are created from the eswitch call
to load the registered eth representors.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove some last leftovers from using the PF netdev as
the e-switch uplink representor.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, when running in sriov switchdev mode, we are using the PF
netdevice as the uplink representor, this is problematic from few aspects:
- will break when the PF isn't eswitch manager (e.g smart NIC env)
- misalignment with other NIC switchdev drivers
- makes us have and maintain special code, hurts the driver quality/robustness
- which in turn opens the door for future bugs
As of each and all of the above, we move to have a dedicated netdev representor
for the uplink vport in a similar manner done for for the VF vports.
This includes the following:
1. have an uplink rep netdev as we have for VF reps
2. all reps use same load/unload functions
3. HW stats for uplink based on physical port counters and not vport counters
4. link state for the uplink managed through PAOS and not vport state
5. the uplink rep has sysfs link to the PF PCI function && uses the PF MAC address
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is prep step towards adding dedicated uplink representor.
The patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The reload of the IB interface done on the offloads stop call is
redundant b/c we do that on mlx5_eswitch_disable_sriov(), remove it.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Old firmware versions don't support this command. Sending it
to any firmware before -41.ucode will crash the firmware.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201975
Fixes: 66e839030f ("iwlwifi: fix wrong WGDS_WIFI_DATA_SIZE")
CC: <stable@vger.kernel.org> #4.19+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that mlxsw driver handles all aspects of updating
the Bloom filter mechanism, set bf_bypass value to false
and allow HW to use Bloom filter.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter is updated on transitions from a single rule pattern,
also called master RP, to eRP table and vice versa. Since rules are
being written to or deleted from the Bloom filter on such transitions,
it is not required to keep the same eRP bank ID for the master RP.
Change master RP index assignment so it will be assigned with zero.
This is consistent with the assignment of the first available spot
that is used for allocating eRP's indices.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bloom filter update is required only for rules which reside on an
eRP. When the region has only a single rule pattern then eRP table
is not used, however insertion of another pattern would trigger a
move to an active eRP table so it is imperative to update the Bloom
filter with all previously configured rules.
Add a method that updates Bloom filter entries for all rules
currently configured in the region, on the event of a transition
from master mask to eRP, or vice versa. For that purpose, maintain
a list of all A-TCAM rules within mlxsw_sp_acl_atcam_region.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add calls to eRP module for updating Bloom filter when a rule is
added or removed from the A-TCAM. eRP module will update the Bloom
filter only for cases in which the region has an active eRP table.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Bloom filter update for rule insertion and rule removal scenarios.
This is done within eRP module in order to assure that Bloom filter
updates are done only for rules which are part of an eRP, as HW does not
consult Bloom filter for entries when there is a single (master) mask in
the region.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 HW uses Bloom filter in order to skip lookups on specific
eRPs. It uses crc-16-Msbit-first calculation over a specific layout
of a rule's key fields combined with eRP ID as well as region ID.
Per potential lookup, iff the Bloom filter entry of the calculated
index is empty, then the lookup can be skipped. Hence, the mlxsw
driver should update the Bloom filter entry per each rule insertion
or deletion when rules are part of an eRP.
Add functions for adding and deleting entries in the Bloom filter.
In order to do so also add crc-16 computation based on the specific
Spectrum-2 polynomial and a function for encoding the crc-16 input
in the manner dictated by HW implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lay the foundations for Bloom filter handling. Introduce a new file for
Bloom filter actions.
Add struct mlxsw_sp_acl_bf to struct mlxsw_sp_acl_erp_core and initialize
the Bloom filter data structure. Also take care of proper destruction when
terminating.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
