Support prescaler 1/16 and 1/64, in addition to current 1 and 1/4.
Supporting below 2400bps was dropped long time ago in mainline.
Since then, setting lower rate has been resulting in erroneous
register value, without indicating any errors through API.
This patch adds more prescaler to support lower rates again.
This still doesn't check range, but we won't hit the case because
even 50bps at 48MHz clock is now supported.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 1ba7622094 (serial: sh-sci: console Runtime PM support,
from Magnus Damm <damm@opensource.se>, 2011-08-03), tried to support
console runtime PM, but unfortunately it didn't work for us for some
reason. We did not investigated further at that time, instead would
like to propose a different approach.
In Linux tty/serial world, to get console PM work properly, a serial
client driver does not have to maintain .runtime_suspend()/..resume()
calls itself, but can leave console power power management handling to
the serial core driver.
This patch moves the sh-sci driver in that direction.
Notes:
* There is room to optimize console runtime PM more aggressively by
maintaining additional local runtime PM calls, but as a first step
having .pm() operation would suffice.
* We still have a couple of direct calls to sci_port_enable/..disable
left in the driver. We have to live with them, because they're out
of serial core's help.
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This partially reverts commit 1ba7622094 (serial: sh-sci: console
Runtime PM support, from Magnus Damm <damm@opensource.se>, 2011-08-03).
The generic 'serial_core' can take care of console PM maintenance,
so all (or at least the first thing) we have to do to get console PM
work properly, is to implement uart_ops ->pm() operation in the sh-sci
serial client driver.
This patch partially reverts the commit above, but leaving sci_reset()
change in place, because sci_reset() is already part of another commit
(73c3d53f38 serial: sh-sci: Avoid FIFO clear for MCE toggle.).
A revised version of console PM support follows next.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5a50a01bf0 (sh-sci / PM: Use power.irq_safe, from
Rafael J. Wysocki <rjw@sisk.pl>, 2011-08-24).
In order to get console PM work properly, we should implement uart_ops
->pm() operation, rather than sprinkle band-ading runtime PM calls in
the driver.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 048be431e4 (sh-sci / PM: Avoid deadlocking runtime
PM, from Rafael J. Wysocki <rjw@sisk.pl>, 2012-03-09).
In order to get console PM work properly, we should implement uart_ops
->pm() operation, rather than sprinkle band-ading runtime PM calls in
the driver.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
To be sure, the TTY buffers (and later some stuff) are gone along with
the tty_port, we have to call tty_port_destroy at tear-down places.
This is mostly where the structure containing a tty_port is freed.
This patch does exactly that -- put tty_port_destroy at those places.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
This one is special as we need more work to be done. Previously,
the tty_port was initialized at module load time, but to be able to
destroy the port and init it again, we now do the initialization in
probe and destroy in remove. I.e. at more appropriate places for that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue.
Those using refcounting are safe now, but for those which do not we
introduce a function to be called right before the tty_port is freed
by the drivers.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
Here it is enough to switch to refcounting in tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit "TTY: move tty buffers to tty_port", the tty buffers are
not freed in some drivers. This is because tty_port_destructor is not
called whenever a tty_port is freed. This was an assumption I counted
with but was unfortunately untrue. So fix the drivers to fulfil this
assumption.
PTY is one of those, here we just need to use tty_port_put instead of
kfree. (Assuming tty_port_destructor does not need port->ops to be set
which we change here too.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not access unsafe port->tty pointer when we have a safe tty
already. Use the safe one.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With hotpluggable and memoryless nodes, it's possible that node 0 will
not be online, so use the first online node's zonelist rather than
hardcoding node 0 to pass a zonelist with all zones to the oom killer.
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch performs a small cleanup tty/Serial/Kconfig file by removing
unneeded ARCH dependencies. This dependencies already included in
board/type symbols.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is following what 8250 driver is doing in console write function,
to avoid the hardware lockup case.
v2: incldudes the <linux/nmi.h>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this we will shift data into oblivion and give wrong results on
some configurations
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Zynq platform requires the use of CONFIG_OF. Remove the #ifdef
conditionals in the uartps driver. Make dependency explicit in Kconfig.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should do hangup on dcd loss if CLOCAL is false not true.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=49911
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch check whether the fifo lenth is empty before writing new data to fifo.If condition
is true,ifx_spi_write need to trigger one mrdy_assert. If condition is false,the mrdy_assert
will be trigger by the next ifx_spi_io.
Cc: Bi Chao <chao.bi@intel.com>
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to correct the bit mapping of "MORE" and "CTS" in SPI frame header.
Per SPI protocol, SPI header is encoded with length of 4 byte, which is defined
as below:
bit 0 ~ 11: current data size;
bit 12: "MORE" bit;
bit 13: reserve
bit 14 ~ 15: reserve
bit 16 ~ 27: next data size
bit 28: RI
bit 29: DCD
bit 30: CTS/RTS
bit 31: DSR/DTR
According to above SPI header structure, the bit mapping of "MORE" and "CTS" is
incorrect in function ifx_spi_decode_spi_header();
Cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to implement following 2 places to avoid potential error when IFX6x60 port shutdown:
1) Clear Flag IFX_SPI_STATE_IO_AVAILABLE to disable data transfer when Modem port is shutdown;
2) Clear Flag IFX_SPI_STATE_IO_IN_PROGRESS and IFX_SPI_STATE_IO_READY when reopen port.
This is because last port shutdown may happen when SPI/DMA transfer is in progress, if the last
data transfer is not completed(for example due to modem reset), the Flag IFX_SPI_STATE_IO_IN_PROGRESS
will be set forever, so when IFX port is activated again, IFX_SPI_STATE_IO_IN_PROGRESS will prevent
transferring data forever. And if don't clear IFX_SPI_STATE_IO_READY, it may cause one more SPI frame
transferring in spit there is not data need to be transfer.
cc: liu chuansheng <chuansheng.liu@intel.com>
cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver for non-standard on-chip UART, instantiated in the ARC (Synopsys)
FPGA Boards such as ARCAngel4/ML50x
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We pass both port and state because the original caller had both to hand.
With all the attribute callers this won't be true so do the conversion in
the function itself.
The current callers all do lock/query/unlock. This won't be true for future
set based cases but there are plenty of get ones that will exist so split
the code with a helper for the future cases.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two patches needed are now in the tree. The first added the sysfs
interface and directly accesses the uartclk. The second provides a
proper interface for getting the values.
Wire them together.
This formes a basis for both get and set methods for any of the other uart
properties and we can now fill them out further.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These printks should all be emitted at KERN_DEBUG level.
Make them dependent on CONFIG_DEBUG or (#define DEBUG)
simplify the code a bit.
Add missing newlines where appropriate.
Most all of these messages could be deleted too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For checkpoint/restore we need to know if tty has
exclusive or packet mode set, as well as if pty
is currently locked. Just to be able to restore
this characteristics.
For this sake the following ioctl codes are introduced
- TIOCGPKT to get packet mode state
- TIOCGPTLCK to get Pty locked state
- TIOCGEXCL to get Exclusive mode state
Note this ioctls are a bit unsafe in terms of data
obtained consistency. The tty characteristics might
be changed right after ioctl complete. Keep it in
mind and use this ioctl carefully.
v2:
- Use TIOC prefix for ioctl codes (by jslaby@)
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Pavel Emelyanov <xemul@parallels.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since this ioctl is for pty devices only move it to pty.c.
v2:
- drop PTY_TYPE_MASTER test since it's master peer
ioctl anyway (by jslaby@)
Suggested-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Pavel Emelyanov <xemul@parallels.com>
CC: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently this driver expects the clock-frequency attribute. This
patch allows getting clock-frequency through clk driver API
clk_get_rate() if clock-frequency attribute is not defined.
So in the device bindings for serial device, one can add clocks
phandle to refer to the clk device to get the rate.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARN_RATELIMIT() expects the warning to end with a newline if one
is needed.
Not doing so results in odd looking warnings such as:
[ 1339.454272] tty is NULLPid: 7147, comm: kworker/4:0 Tainted: G W 3.7.0-rc2-next-20121025-sasha-00001-g673f98e-dirty #75
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch make use of del_timer instead of del_timer_sync in the
interrupt context.
The spi_timer function don't use any resources that may release after
running del_timer,
so using the del_timer is also safe and enough in this context.
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Tested-by: Chuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch make use of mod_timer instead of add_timer in the mrdy_assert function.
Because the srdy interrupter can go high when we are running function mrdy_assert and mrdy_assert
can be called by multi-entry. In our medfield platform, spi stress test can encounter this
error logs triggered by the BUG_ON of add_timer function.This patch had been tested on
our medfield platform.
the scenario:
CPU0 CPU1
mrdy_assert
set_bit(IFX_SPI_STATE_TIMER_PENDING)
ifx_spi_handle_srdy
...
clear_bit(IFX_SPI_STATE_TIMER_PENDING)
...
mrdy_assert
set_bit(IFX_SPI_STATE_TIMER_PENDING)
...
add_timer
...
add_timer
Cc: liu chuansheng <chuansheng.liu@intel.com>
Cc: Bi Chao <chao.bi@intel.com>
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPI protocol driver only provide one function (swap_buf()) to swap SPI
data into big endian format, which is only available when SPI
controller's word width is 16 bits. But word width could be configured
as 8/16/32 bits, different word width configure should be mapped to
different swap methods.This patch is to make SPI protocol driver choose
the right swap function corresponding to SPI word width configuration.
cc: liu chuansheng <chuansheng.liu@intel.com>
cc: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This switches a bunch of allocation and remapping to use the
devm_* garbage collected methods and cleans up the error
path and remove() paths consequently.
devm_ioremap() is only in <linux/io.h> so fix up the
erroneous <asm/*> include as well.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the array serial_omap_console_ports is hard coded to 4.
Make it depend on the maximum uart count.
Post to [cfc55bc ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6]
the max ports is 6.
Cc: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Special character detect enable if enabled by default.Received data
comparison with XOFF2 data happens by default.
tty provides only XOFF1 no X0FF2 is provided so no need
to enable check for XOFF2.
Keeping this enabled might give some slow transfers due to dummy xoff2
comparison with xoff2 reset value.
Since not all want the XOFF2 support lets not enable it by
default.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_context_loss_count returns an int however it is stored in
unsigned integer context_loss_cnt . This patch tries to make
context_loss_cnt int. So that in case of errors the value
(which may be negative) is not interpreted wrongly.
In serial_omap_runtime_resume in case of errors returned by
get_context_loss_count print a warning and do a restore.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 957ee7270d
(serial: omap: fix software flow control).
As Russell has pointed out, that commit isn't fixing
Software Flow Control at all, and it actually makes
it even more broken.
It was agreed to revert this commit and use Russell's
latest UART patches instead.
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>