Commit Graph

16 Commits

Author SHA1 Message Date
Tuomas Tynkkynen
45e01f401a
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
2018-02-13 09:37:22 +01:00
Chen-Yu Tsai
59268ffe87 ARM: dts: sun7i: Enable HDMI support on some A20 devices
All the A20 devices I own have standard HDMI connectors wired
to the dedicated HDMI pins on the SoC:

  - Bananapi M1+
  - Cubieboard 2
  - Cubietruck
  - Lamobo R1 (or Bananapi R1)

Development boards from Olimex also have standard HDMI connectors.
Schematics for them are publicly available. Enable HDMI on them as
well.

  - Olimex A20-OLinuXino-LIME
  - Olimex A20-OLinuXino-LIME2
  - Olimex A20-OLinuXino-MICRO

Enable the display pipeline and HDMI output for them.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Priit Laes <plaes@plaes.org> # Cubietruck, A20-OLinuXino-MICRO
Tested-by: Olliver Schinagl <oliver@schinagl.nl> # A20-OLinuXino-LIME2
Tested-by: Jonathan Liu <net147@gmail.com> # A20-OLinuXino-LIME
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-18 09:39:01 +08:00
Icenowy Zheng
a3ccbc0097 ARM: sun7i: a20: enable ac/battery power supplies for Lamobo R1 board
The Lamobo R1 board connected the ACIN of the AXP209 PMIC to a MicroUSB
port, and the battery input is connected to a generic connector.

Enable these two power supplies in the device tree.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-09-17 12:04:29 +02:00
Chen-Yu Tsai
8a92770b64 ARM: sunxi: common-regulators: Drop pinmux settings for GPIO pins
As part of our effort to move pinctrl/GPIO interlocking into the
driver where it belongs, this patch drops the definition and usage
of the pinmux settings for the common regulators defined in
sunxi-common-regulators.dtsi.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-05-14 08:32:31 +02:00
Linus Torvalds
85d604902e ARM: Device-tree updates
Device-tree continues to see lots of updates. The majority of patches
 here are smaller changes for new hardware on existing platforms, and
 there are a few larger changes worth pointing out.
 
 Major new platforms:
 
  - Gemini has been ported to DT, so a handful of "new" platforms moved over
    from board files
  - Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288 SoM and RDK
  - A bunch of embedded platforms, several Linksys platforms, Synology DS116,
  - Motorola Droid4 (really old OMAP-based phone) support is added.
 
 Some refactorings, i.e. Allwinner H3/H5 support is commonalized.
 
 And lots of smaller changes, cleanups, etc. See shortlog for more description
 
 We're adding ability to cross-include DT files between arm and arm64,
 by creating appropriate links in the dt-include directory, and using arm/
 and arm64/ as include prefixes. This will avoid other local hacks such as
 per-file links between the two arch trees (this broke for external mirroring
 of DT contents). Now they can just provide their own appropriate dt-include
 hierarcy per platform.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJZEAoxAAoJEIwa5zzehBx3li8P/iIMy0HmGuJ0JsTldMk4kgkM
 1Ci/gcgKYn43m68RwvZCwkBxVibqCdMbBtLHCUt3ScGIYdj6mUG8axRHvFW/tsGf
 BP0Y5pxm7l1BlHOKed97bJUeMyqqG13szzS7aB5L6cyZt41lAAkpCx4OFAuIlaxo
 XM1v2xRSxqSf/zp4px83qX2hdHIpe4ZGlDiNh8rCBBnKMY4PqhK0V7TFLPOKbFnr
 stIvD1TpvzacN67JVo1En0rCFgXSCwJ+CTumAOIx4tflV48ymY5THRNtI1ogFosc
 1IfOxnC9DyRVM2ubFF7/ZLFbmn5KHu6ZwPLN+8Wl2McbT96PAtJ3h/zgTnuk4Tvf
 GaAfqcyAXFeiZGU+bkkGiaQwXRDBroxVuNFTgERNgF70GUrDpBzd3tJO2rx7oZCS
 Rj2QvKfBDBr9g5ldVGjOBIq/G9DeN5TtR6gyr/hCS/nm0NlYQ90Pzing0Nj8PDC9
 /AOa4k4wUWo/oaFucBEeATCxto3TKpmBuP1I31sWG8StKVSJbIek2dSMcWSVFrG5
 6/pzmuE4C7ZlshcFAUOeHxMVjBhTya5mDZQgZhCAnwhVMzrrpMTHTi27nbWcv/k8
 9TH+ig5DoKL65FFE92ZkEb4S47SaD2+qKjEzJMDNQzc5WuY4l7pfDQoSn3YLjzKZ
 xSKQEsmyOW0/0v8ecDKP
 =v6w6
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM Device-tree updates from Olof Johansson:
 "Device-tree continues to see lots of updates. The majority of patches
  here are smaller changes for new hardware on existing platforms, and
  there are a few larger changes worth pointing out.

  Major new platforms:

   - Gemini has been ported to DT, so a handful of "new" platforms moved
     over from board files

   - Rockchip RK3288 support for Tinkerboard and Phytec phyCORE-RK3288
     SoM and RDK

   - A bunch of embedded platforms, several Linksys platforms, Synology
     DS116,

   - Motorola Droid4 (really old OMAP-based phone) support is added.

  Some refactorings, i.e. Allwinner H3/H5 support is commonalized.

  And lots of smaller changes, cleanups, etc. See shortlog for more
  description

  We're adding ability to cross-include DT files between arm and arm64,
  by creating appropriate links in the dt-include directory, and using
  arm/ and arm64/ as include prefixes. This will avoid other local hacks
  such as per-file links between the two arch trees (this broke for
  external mirroring of DT contents). Now they can just provide their
  own appropriate dt-include hierarcy per platform"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (349 commits)
  ARM: dts: exynos: Use - instead of @ for DT OPP entries
  arm: spear6xx: add DT description of the ADC on SPEAr600
  arm: spear6xx: remove unneeded pinctrl properties in spear600-evb
  arm: spear6xx: switch spear600-evb to the new flash partition DT binding
  arm: spear6xx: fix spaces in spear600-evb.dts
  arm: spear6xx: use node labels in spear600-evb.dts
  arm: spear6xx: add labels to various nodes in spear600.dtsi
  ARM: dts: vexpress: fix few unit address format warnings
  ARM: dts: at91: sama5d3_xplained: not all ADC channels are available
  ARM: dts: at91: sama5d3_xplained: fix ADC vref
  ARM: dts: at91: add envelope detector mux to the Axentia TSE-850
  ARM: dts: armada-38x: label USB and SATA nodes
  ARM: dts: imx6q-utilite-pro: add hpd gpio
  ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
  ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
  ARM: dts: imx: add Gateworks Ventana GW5903 support
  ARM: dts: i.MX25: add AIPS control registers
  ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
  ARM: dts: imx7-colibri: remove 1.8V fixed regulator
  ARM: dts: imx7-colibri: allow to disable Ethernet rail
  ...
2017-05-09 09:54:39 -07:00
Chen-Yu Tsai
85d2913614 ARM: dts: sunxi: Remove no longer used pinctrl/sun4i-a10.h header
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.

Remove the #include entry with the following command:

    sed --follow-symlinks -i -e '/pinctrl\/sun4i-a10.h/D' \
	arch/arm/boot/dts/sun?i*.*

arch/arm/boot/dts/sun9i-a80.dtsi was then edited to remove the extra
empty line.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-03-27 13:39:58 +02:00
Florian Fainelli
0cdefd5b54 ARM: dts: sun7i: lamobo-r1: Fix CPU port RGMII settings
The CPU port of the BCM53125 is configured with RGMII (no delays) but
this should actually be RGMII with transmit delay (rgmii-txid) because
STMMAC takes care of inserting the transmitter delay. This fixes
occasional packet loss encountered.

Fixes: d7b9eaff5f ("ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board")
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-03-20 09:30:39 +01:00
Maxime Ripard
1edcd36fcb ARM: sunxi: Convert pinctrl nodes to generic bindings
Now that we can handle the generic pinctrl bindings, convert our DT to it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-26 08:27:11 +01:00
Maxime Ripard
119c366aea ARM: sunxi: Remove useless allwinner,pull property
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).

Remove these properties to make it obvious that we do not set anything in
such a case.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-26 08:24:50 +01:00
Maxime Ripard
d312f6fb80 ARM: sunxi: Remove useless allwinner,drive property
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-26 08:24:50 +01:00
Chen-Yu Tsai
6be9aa1341 ARM: dts: sun7i: lamobo-r1: Enable audio codec
Lamobo R1 has a headphone jack for audio output, and an onboard
microphone. These are tied to the SoC's internal audio codec.

Enable the audio codec.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-07-11 08:26:17 +02:00
Chen-Yu Tsai
f64cb7c724 ARM: dts: sun7i: lamobo-r1: Fix GPIO flags in reg_ahci_5v
reg_ahci_5v uses a GPIO in active high mode. Use the proper macro,
instead of just 0 for the GPIO flags.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-07-11 08:26:17 +02:00
Chen-Yu Tsai
bec72ca528 ARM: dts: sun7i: lamobo-r1: Remove usb1 vbus regulator
USB1 VBUS is directly tied to the 5V rail on the board. It is not
individually controllable. Drop the regulator.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-07-09 10:10:14 +02:00
Chen-Yu Tsai
377c2b3483 ARM: dts: sun7i: lamobo-r1: Fix USB-based WiFi module power
On the Lamobo R1, USB2 is connected to the RTL8192CU WiFi module.
The power enable pin is connected to PH12.

Fix the enable pin the reg_usb2_vbus.

Also disable ohci1, as the WiFi module is USB 2.0 capable.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-07-09 10:09:59 +02:00
Florian Fainelli
d7b9eaff5f ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board
Now that we have a proper binding for Ethernet switches hanging off
different buses, and a driver for the BCM53125 switch, add its Device
Tree as a child MDIO node, at MDIO address 30 (Broadcom pseudo-PHY
address) and describe the ports layout of the Lamobo R1 board.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-07-04 21:18:08 +02:00
Jelle de Jong
f9ca30440c ARM: dts: sun7i: Add dts file for the lamobo-r1 board
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.

Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2016-02-25 10:12:27 -08:00