The IS_ERR_OR_NULL(priv->clock) check inside
sja1105_ptp_clock_unregister() is preventing cancel_delayed_work_sync
from actually being run.
Additionally, sja1105_ptp_clock_unregister() does not actually get run,
when placed in sja1105_remove(). The DSA switch gets torn down, but the
sja1105 module does not get unregistered. So sja1105_ptp_clock_unregister
needs to be moved to sja1105_teardown, to be symmetrical with
sja1105_ptp_clock_register which is called from the DSA sja1105_setup.
It is strange to fix a "fixes" patch, but the probe failure can only be
seen when the attached PHY does not respond to MDIO (issue which I can't
pinpoint the reason to) and it goes away after I power-cycle the board.
This time the patch was validated on a failing board, and the kernel
panic from the fixed commit's message can no longer be seen.
Fixes: 29dd908d35 ("net: dsa: sja1105: Cancel PTP delayed work on unregister")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the FDB dump taken from first-generation switches also
contains information on whether entries are static or not. So use that
instead of searching through the driver's tables.
Fixes: d763778224 ("net: dsa: sja1105: Implement is_static for FDB entries on E/T")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When put under a bridge with vlan_filtering 0, the SJA1105 ports will
flood all traffic as if learning was broken. This is because learning
interferes with the rx_vid's configured by dsa_8021q as unique pvid's.
So learning technically still *does* work, it's just that the learnt
entries never get matched due to their unique VLAN ID.
The setting that saves the day is Shared VLAN Learning, which on this
switch family works exactly as desired: VLAN tagging still works
(untagged traffic gets the correct pvid) and FDB entries are still
populated with the correct contents including VID. Also, a frame cannot
violate the forwarding domain restrictions enforced by its classified
VLAN. It is just that the VID is ignored when looking up the FDB for
taking a forwarding decision (selecting the egress port).
This patch activates SVL, and the result is that frames with a learnt
DMAC are no longer flooded in the scenario described above.
Now exactly *because* SVL works as desired, we have to revisit some
earlier patches:
- It is no longer necessary to manipulate the VID of the 'bridge fdb
{add,del}' command when vlan_filtering is off. This is because now,
SVL is enabled for that case, so the actual VID does not matter*.
- It is still desirable to hide dsa_8021q VID's in the FDB dump
callback. But right now the dump callback should no longer hide
duplicates (one per each front panel port's pvid, plus one for the
VLAN that the CPU port is going to tag a TX frame with), because there
shouldn't be any (the switch will match a single FDB entry no matter
its VID anyway).
* Not really... It's no longer necessary to transform a 'bridge fdb add'
into 5 fdb add operations, but the user might still add a fdb entry with
any vid, and all of them would appear as duplicates in 'bridge fdb
show'. So force a 'bridge fdb add' to insert the VID of 0**, so that we
can prune the duplicates at insertion time.
** The VID of 0 is better than 1 because it is always guaranteed to be
in the ports' hardware filter. DSA also avoids putting the VID inside
the netlink response message towards the bridge driver when we return
this particular VID, which makes it suitable for FDB entries learnt
with vlan_filtering off.
Fixes: 227d07a07e ("net: dsa: sja1105: Add support for traffic through standalone ports")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a better way to signal this, perhaps in phylink_validate, but
for now just print this error message as guidance for other people
looking at this driver's code while trying to rework PHYLINK.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYLINK being designed with PHYs in mind that can change MII protocol,
for correct operation it is necessary to ensure that the PHY interface
mode stays the same (otherwise clear the supported bit mask, as
required).
Because this is just a hypothetical situation for now, we don't bother
to check whether we could actually support the new PHY interface mode.
Actually we could modify the xMII table, reset the switch and send an
updated static configuration, but adding that would just be dead code.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been pointed out that PHYLINK can call mac_config only to update
the phy_interface_type and without knowing what the AN results are.
Experimentally, when this was observed to happen, state->link was also
unset, and therefore was used as a proxy to ignore this call. However it
is also suggested that state->link is undefined for this callback and
should not be relied upon.
So let the previously-dead codepath for SPEED_UNKNOWN be called, and
update the comment to make sure the MAC's behavior is sane.
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first generation switches don't tell us through the dynamic config
interface whether the dumped FDB entries are static or not (the LOCKEDS
bit from P/Q/R/S).
However, now that we're keeping a mirror of all 'bridge fdb' commands in
the static config, this is an opportunity to compare a dumped FDB entry
to the driver's private database. After all, what makes an entry static
is that *we* added it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A FDB entry means that "frames that match this VID and DMAC must be
forwarded to this port".
In the case of dsa_8021q however, the VID is not a single one (and
neither two, as my previous patch assumed). The VID can be set either by
the CPU port (1 tx_vid), or by any of the other front-panel port (n-1
rx_vid's).
Fixes: 93647594d8 ("net: dsa: sja1105: Hide the dsa_8021q VLANs from the bridge fdb command")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason why this wasn't tackled earlier is that I had hoped I
understood the user manual wrong. But unfortunately hacks are required
in order to retrieve the static/dynamic nature of FDB entries on SJA1105
P/Q/R/S, since this info is stored in the writeback buffer of the
dynamic config command.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to add support for LOCKEDS (static FDB entries) on SJA1105
P/Q/R/S, at first I didn't remember how the abstraction I created
worked, and actually thought it works by mistake.
To avoid other people staring at the code and not making much sense out
of it, add some comments at the top of the file.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 8456721dd4 ("net: dsa: sja1105: Add support for
configuring address ageing time"), we started to reset the switch rather
often (each time the bridge core changes the ageing time on a switch
port).
The unfortunate reality is that SJA1105 doesn't have any {cold, warm,
whatever} reset mode in which it accepts a new configuration stream
without flushing the FDB. Instead, in its world, the FDB *is* an
optional part of the static configuration.
So we play its game, and do what we also do for VLANs: for each 'bridge
fdb' command, we add the FDB entry through the dynamic interface, and we
append the in-kernel static config memory with info that we're going to
use later, when the next reset command is going to be issued.
The result is that 'bridge fdb' commands are now persistent (dynamically
learned entries are lost, but that's ok).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of the commit 1da7382134 ("net: dsa: sja1105: Add FDB
operations for P/Q/R/S series") message, I said that:
At the moment only FDB entries installed statically through 'bridge fdb'
are visible in the dump callback - the dynamically learned ones are
still under investigation.
It looks like the reason why they were not visible in 'bridge fdb' was
that they were never learned - always flooded.
SJA1105 P/Q/R/S manual says about the MAXADDRP[port] field:
Specify the maximum number of MAC address dynamically learned from
the respective port. It is used to limit the number of learned MAC
addresses per port.
It looks like not providing a value in the static config (aka providing
zeroes) is enough for it to not store the learned addresses in the FDB.
For now we divide the 1024 entry FDB "equally" amongst the 5 ports. This
may be revisited if the situation calls for that - for now I'm happy
that learning works.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1da7382134 ("net: dsa: sja1105: Add FDB operations for
P/Q/R/S series"), these bits were set in the static config, but
apparently they did not do anything. The reason is that the packing
accessors for them were part of a patch I forgot to send.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SJA1105 there is no concept of 'default values' per se, everything
needs to be driver-supplied through the static configuration tables.
The issue is that the hardware manual says that 'at least the default
untagging VLAN' is mandatory to be provided through the static config.
But VLAN 0 isn't a very good initial pvid - its use is reserved for
priority-tagged frames, and the layers of the stack that care about
those already make sure that this VLAN is installed, as can be seen in
the message below:
8021q: adding VLAN 0 to HW filter on device swp2
So change the pvid provided through the static configuration to 1, which
matches the bridge core's defaults.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Arnd Bergmann pointed out in commit 78fe8a28fb ("net: dsa: sja1105:
fix ptp link error"), there is no point in having PTP support as a
separate loadable kernel module.
So remove the exported symbols and make sja1105.ko contain PTP support
or not based on CONFIG_NET_DSA_SJA1105_PTP.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a reversed dependency, it is possible to build
the lower ptp driver as a loadable module and the actual
driver using it as built-in, causing a link error:
drivers/net/dsa/sja1105/sja1105_spi.o: In function `sja1105_static_config_upload':
sja1105_spi.c:(.text+0x6f0): undefined reference to `sja1105_ptp_reset'
drivers/net/dsa/sja1105/sja1105_spi.o:(.data+0x2d4): undefined reference to `sja1105et_ptp_cmd'
drivers/net/dsa/sja1105/sja1105_spi.o:(.data+0x604): undefined reference to `sja1105pqrs_ptp_cmd'
drivers/net/dsa/sja1105/sja1105_main.o: In function `sja1105_remove':
sja1105_main.c:(.text+0x8d4): undefined reference to `sja1105_ptp_clock_unregister'
drivers/net/dsa/sja1105/sja1105_main.o: In function `sja1105_rxtstamp_work':
sja1105_main.c:(.text+0x964): undefined reference to `sja1105_tstamp_reconstruct'
drivers/net/dsa/sja1105/sja1105_main.o: In function `sja1105_setup':
sja1105_main.c:(.text+0xb7c): undefined reference to `sja1105_ptp_clock_register'
drivers/net/dsa/sja1105/sja1105_main.o: In function `sja1105_port_deferred_xmit':
sja1105_main.c:(.text+0x1fa0): undefined reference to `sja1105_ptpegr_ts_poll'
sja1105_main.c:(.text+0x1fc4): undefined reference to `sja1105_tstamp_reconstruct'
drivers/net/dsa/sja1105/sja1105_main.o:(.rodata+0x5b0): undefined reference to `sja1105_get_ts_info'
Change the Makefile logic to always build the ptp module
the same way as the rest. Another option would be to
just add it to the same module and remove the exports,
but I don't know if there was a good reason to keep them
separate.
Fixes: bb77f36ac2 ("net: dsa: sja1105: Add support for the PTP clock")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/dsa/sja1105/sja1105_main.c:1848:6:
warning: symbol 'sja1105_port_rxtstamp' was not declared. Should it be static?
drivers/net/dsa/sja1105/sja1105_main.c:1869:6:
warning: symbol 'sja1105_port_txtstamp' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per the DT phy-mode specification, RGMII delays are applied by the
MAC when there is no PHY present on the link.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pad_mii_tx registers point to the same memory region but were
unused. So convert to using these for RGMII I/O cell configuration, as
they bear a shorter name.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first fact that needs to be stated is that the per-MAC settings in
SJA1105 called EGRESS and INGRESS do *not* disable egress and ingress on
the MAC. They only prevent non-link-local traffic from being
sent/received on this port.
So instead of having .phylink_mac_config essentially mess with the STP
state and force it to DISABLED/BLOCKING (which also brings useless
complications in sja1105_static_config_reload), simply add the
.phylink_mac_link_down and .phylink_mac_link_up callbacks which inhibit
TX at the MAC level, while leaving RX essentially enabled.
Also stop from trying to put the link down in .phylink_mac_config, which
is incorrect.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used to stop egress traffic in .phylink_mac_link_up.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the driver is now using PHYLINK exclusively, it makes sense to
remove all references to it and replace them with PHYLINK.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that replaces the link speed numbers used in
the driver with the corresponding ethtool macros.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the PTP support towards userspace applications such as
linuxptp.
The switches can timestamp only trapped multicast MAC frames, and
therefore only the profiles of 1588 over L2 are supported.
TX timestamping can be enabled per port, but RX timestamping is enabled
globally. As long as RX timestamping is enabled, the switch will emit
metadata follow-up frames that will be processed by the tagger. It may
be a problem that linuxptp does not restore the RX timestamping settings
when exiting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meta frame reception relies on the hardware keeping its promise that it
will send no other traffic towards the CPU port between a link-local
frame and a meta frame. Otherwise there is no other way to associate
the meta frame with the link-local frame it's holding a timestamp of.
The receive function is made stateful, and buffers a timestampable frame
until its meta frame arrives, then merges the two, drops the meta and
releases the link-local frame up the stack.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without noticing any particular issue, this patch ensures that
management traffic is treated with the maximum priority on RX by the
switch. This is generally desirable, as the driver keeps a state
machine that waits for metadata follow-up frames as soon as a management
frame is received. Increasing the priority helps expedite the reception
(and further reconstruction) of the RX timestamp to the driver after the
MAC has generated it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used to keep state for RX timestamping. It is global
because the switch serializes timestampable and meta frames when
trapping them towards the CPU port (lower port indices have higher
priority) and therefore having one state machine per port would create
unnecessary complications.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This table is used to program the switch to emit "meta" follow-up
Ethernet frames (which contain partial RX timestamps) after each
link-local frame that was trapped to the CPU port through MAC filtering.
This includes PTP frames.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On TX, timestamping is performed synchronously from the
port_deferred_xmit worker thread.
In management routes, the switch is requested to take egress timestamps
(again partial), which are reconstructed and appended to a clone of the
skb that was just sent. The cloning is done by DSA and we retrieve the
pointer from the structure that DSA keeps in skb->cb.
Then these clones are enqueued to the socket's error queue for
application-level processing.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The design of this PHC driver is influenced by the switch's behavior
w.r.t. timestamping. It exposes two PTP counters, one free-running
(PTPTSCLK) and the other offset- and frequency-corrected in hardware
through PTPCLKVAL, PTPCLKADD and PTPCLKRATE. The MACs can sample either
of these for frame timestamps.
However, the user manual warns that taking timestamps based on the
corrected clock is less than useful, as the switch can deliver corrupted
timestamps in a variety of circumstances.
Therefore, this PHC uses the free-running PTPTSCLK together with a
timecounter/cyclecounter structure that translates it into a software
time domain. Thus, the settime/adjtime and adjfine callbacks are
hardware no-ops.
The timestamps (introduced in a further patch) will also be translated
to the correct time domain before being handed over to the userspace PTP
stack.
The introduction of a second set of PHC operations that operate on the
hardware PTPCLKVAL/PTPCLKADD/PTPCLKRATE in the future is somewhat
unavoidable, as the TTEthernet core uses the corrected PTP time domain.
However, the free-running counter + timecounter structure combination
will suffice for now, as the resulting timestamps yield a sub-50 ns
synchronization offset in steady state using linuxptp.
For this patch, in absence of frame timestamping, the operations of the
switch PHC were tested by syncing it to the system time as a local slave
clock with:
phc2sys -s CLOCK_REALTIME -c swp2 -O 0 -m -S 0.01
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are needed for the situation where the switch driver and the PTP
driver are both built as modules.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The incl_srcpt setting makes the switch mangle the destination MACs of
multicast frames trapped to the CPU - a primitive tagging mechanism that
works even when we cannot use the 802.1Q software features.
The downside is that the two multicast MAC addresses that the switch
traps for L2 PTP (01-80-C2-00-00-0E and 01-1B-19-00-00-00) quickly turn
into a lot more, as the switch encodes the source port and switch id
into bytes 3 and 4 of the MAC. The resulting range of MAC addresses
would need to be installed manually into the DSA master port's multicast
MAC filter, and even then, most devices might not have a large enough
MAC filtering table.
As a result, only limit use of incl_srcpt to when it's strictly
necessary: when under a VLAN filtering bridge. This fixes PTP in
non-bridged mode (standalone ports). Otherwise, PTP frames, as well as
metadata follow-up frames holding RX timestamps won't be received
because they will be blocked by the master port's MAC filter.
Linuxptp doesn't help, because it only requests the addition of the
unmodified PTP MACs to the multicast filter.
This issue is not seen in bridged mode because the master port is put in
promiscuous mode when the slave ports are enslaved to a bridge.
Therefore, there is no downside to having the incl_srcpt mechanism
active there.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From reading the P/Q/R/S user manual, it appears that TPID is used by
the switch for detecting S-tags and TPID2 for C-tags. Their meaning is
not clear from the E/T manual.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch, pre-cursor to making another change to the
General Parameters Table (incl_srcpt) which does not logically pertain
to the sja1105_change_tpid function name, but not putting it there would
otherwise create a need of resetting the switch twice.
So simply move the existing code into the .port_vlan_filtering callback,
where the incl_srcpt change will be added as well.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware values for link speed are held in the sja1105_speed_t enum.
However they do not increase in the order that sja1105_get_speed_cfg was
iterating over them (basically from SJA1105_SPEED_AUTO - 0 - to
SJA1105_SPEED_1000MBPS - 1 - skipping the other two).
Another bug is that the code in sja1105_adjust_port_config relies on the
fact that an invalid link speed is detected by sja1105_get_speed_cfg and
returned as -EINVAL. However storing this into an enum that only has
positive members will cast it into an unsigned value, and it will miss
the negative check.
So take the simplest approach and remove the sja1105_get_speed_cfg
function and replace it with a simple switch-case statement.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX VLANs and RX VLANs are an internal implementation detail of DSA for
frame tagging. They work by installing special VLANs on switch ports in
the operating modes where no behavior change w.r.t. VLANs can be
observed by the user.
Therefore it makes sense to hide these VLANs in the 'bridge fdb'
command, as well as translate the pvid into the RX VID and TX VID on
'bridge fdb add' and 'bridge fdb del' commands.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a cosmetic patch that simplifies the code by removing a
redundant check. A logical AND-with-zero performed on a zero is still
zero.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for manipulating the L2 forwarding database (dump,
add, delete) for the second generation of NXP SJA1105 switches.
At the moment only FDB entries installed statically through 'bridge fdb'
are visible in the dump callback - the dynamically learned ones are
still under investigation.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management routes are one-shot FDB rules installed on the CPU port for
sending link-local traffic. They are a prerequisite for STP, PTP etc to
work.
Also make a note that removing a management route was not supported on
the previous generation of switches.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conceptually, if an entry is not found in the requested hardware table,
it is not an invalid request - so change the error returned
appropriately.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are needed in order to implement the switchdev FDB callbacks.
Compared to the E/T generation, not only the ABI (bit offsets) is
different, but also the introduction of the HOSTCMD field which permits
O(1) TCAM search for an FDB entry. Make use of the newly introduce
OP_SEARCH to permit that. It will be used while adding and deleting an
FDB entry (to see whether it exists or not).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA callbacks were written with the E/T (first generation) in mind,
which is quite different.
For P/Q/R/S completely new implementations need to be provided, which
are held as function pointers in the priv->info structure. We are
taking a slightly roundabout way for this (a function from
sja1105_main.c reads a structure defined in sja1105_spi.c that
points to a function defined in sja1105_main.c), but it is what it is.
The FDB dump callback works for both families, hence no function pointer
for that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only a single dynamic configuration table of the SJA1105 P/Q/R/S
supports this operation: the FDB.
To keep the existing structure in place (sja1105_dynamic_config_read and
sja1105_dynamic_config_write) and not introduce any new function, a
convention is made for sja1105_dynamic_config_read that a negative index
argument denotes a search for the entry provided as argument.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This appends to the L2 Forwarding and L2 Forwarding Parameters tables
(originally added for first-generation switches) the bits that are new
in the second generation.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was inadvertently copied from the SJA1105 E/T structure and not
tested. Cross-checking with the P/Q/R/S documentation (UM11040) makes
it immediately obvious what the correct bit offsets for this field are.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure is merely an implementation detail and should be hidden
from the sja1105_dynamic_config.h header, which provides to the rest of
the driver an abstract access to the dynamic configuration interface of
the switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/dsa/sja1105/sja1105_static_config.c:446:1: warning:
symbol 'static_config_check_memory_size' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
