drivers/staging/iio/adc/ad7298_ring.c:97:37: warning: 'time_ns' may
be used uninitialized in this function [-Wmaybe-uninitialized]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
kdb <-> kgdb transitioning does not work properly with this UART
driver because the get character routine loops indefinitely as opposed
to returning NO_POLL_CHAR per the expectation of the KDB I/O driver
API.
The symptom is a kernel hang when trying to switch debug modes.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without checking if the auart supports the hardware flow control or not,
the old mxs_auart_set_mctrl() asserted the RTS pin blindly.
This will causes the auart receives wrong data in the following case:
The far-end has already started the write operation, and wait for
the auart asserts the RTS pin. Then the auart starts the read operation,
but mxs_auart_set_mctrl() may be called before we set the RTSCTS in the
mxs_auart_settermios(). So the RTS pin is asserted in a wrong situation,
and we get the wrong data in the end.
This bug has been catched when I connect the mx23(DTE) to the mx53(DCE).
This patch also replaces the AUART_CTRL2_RTS with AUART_CTRL2_RTSEN.
We should use the real the hardware flow control, not the software-controled
hardware flow control.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull two slave-dmaengine fixes from Vinod Koul:
"One fixes the correct use of clock API in imx driver and the other
enables clock for tegra driver, which is used for other tegra driver
conversion to dmanegine in -next."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: enable/disable dma clock
dma: imx-dma: Fix kernel crash due to missing clock conversion
Pull more drm fixes from Dave Airlie:
"Just some intel and nouveau ones this time, intel has more edp panel
fixes for macbooks and nouveau has a suspend/resume regression fix in
there."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
drm/nve0/fifo: add support for the flip completion swmthd
The main purpose of this function is to exclude ME devices
without support for MEI/HECI interface from binding
Currently affected systems are C600/X79 based servers
that expose PCI device even though it doesn't supported ME Interface.
MEI driver accessing such nonfunctional device can corrupt
the system.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01eaf24 "extcon: Convert extcon_gpio to devm_gpio_request_one"
missed the replacement for devm_gpio_request_one. fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4e00daaa9 changed __dev_printk
in a way that broke dynamic-debug's ability to control the dynamic
prefix of dev_dbg(dev,..), but not dev_dbg(NULL,..) or pr_debug(..),
which is why it wasnt noticed sooner.
When dev==NULL, __dev_printk() just calls printk(), which just works.
But otherwise, it assumed that level was always a string like "<L>"
and just plucked out the 'L', ignoring the rest. However,
dynamic_emit_prefix() adds "[tid] module:func:line:" to the string,
those additions all got lost.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Cc: stable <stable@vger.kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjorn's latest patchset does break Gobi 1K and 2K because on both
devices as it claims usb interface 0. That's because usbif 0 is not
handled in the switch statement, and thus the if0 gets claimed when it
should not. So let's just make things even simpler yet, and handle both
the 1K and 2K+ cases separately. This patch should not affect the new
Sierra device support, because those devices are matched via
interface-specific matching and thus should never hit the composite
code.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After watchdog was disabled the driver would stall
due to wrong calculation of credits reduction
The cat&paste bug was introduced in the commit
7bdf72d3d8
mei: introduce mei_data2slots wrapper
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike other parts of the mlx4_ib code, the function build_mlx_header()
doesn't check if the iboe netdev of the given port is valid before
dereferencing it, which can cause a crash if the ethernet interface
has already been taken down.
Fix this by checking for a valid netdev pointer before using it to get
the port MAC address.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
commit 27a7b260f7
md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
changed 0.90 metadata handling to truncated size to 4TB as that is
all that 0.90 can record.
However for RAID0 and Linear, 0.90 doesn't need to record the size, so
this truncation is not needed and causes working arrays to become too small.
So avoid the truncation for RAID0 and Linear
This bug was introduced in 3.1 and is suitable for any stable kernels
from then onwards.
As the offending commit was tagged for 'stable', any stable kernel
that it was applied to should also get this patch. That includes
at least 2.6.32, 2.6.33 and 3.0. (Thanks to Ben Hutchings for
providing that list).
Cc: stable@vger.kernel.org
Signed-off-by: Neil Brown <neilb@suse.de>
- Use kcalloc() / vzalloc() instead of an extra bitmap_zero().
- Add __GFP_NOWARN to kcalloc() since we'll try vzalloc() if it fails.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix some issues around int variables used in data structures related
to memory registration.
Handle int overflow in mlx4_init_icm_table by using a u64 intermediate
variable and changing struct mlx4_icm_table num_obj field to be u32.
Change some more fields/variables to use u32 instead of int to prevent
a case where the variable becomes negative when bit 31 is set.
Also subtract log_mtts_per_seg from the exponent when computing
num_mtt, since its added later on in that very same code area.
This and the previous commit fixes some issues which actually prevent
commit db5a7a65c0 ("mlx4_core: Scale size of MTT table with system
RAM") from working. Now, when the number of MTTs is scaled with the
size of the RAM we can map up to 8TB.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
mlx4_buddy_init uses kmalloc() to allocate bitmaps, which fails when
the required size is beyond the max supported value (or when memory is
too fragmented to handle a huge allocation). Extend this to use use
vmalloc() if kmalloc() fails, and take that into account when freeing
the bitmaps as well.
This fixes a driver load failure when log num mtt is 26 or higher, and
is a step in the direction of allowing to register huge amounts of
memory on large memory systems.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In JPEG mode, the size of image is variable due to different JPEG compression
rate. We only can get the pix->sizeimage from the user.
If we clear pix->sizeimage in soc_camera_try_fmt() then we will get it from:
ret = soc_mbus_image_size(xlate->host_fmt, pix->bytesperline,
pix->height);
if (ret < 0)
return ret;
pix->sizeimage = max_t(u32, pix->sizeimage, ret);
In general, this sizeimage will be larger than the actul JPEG image size.
But vb2 will check the buffer and size of image in __qbuf_userptr():
/* Check if the provided plane buffer is large enough */
if (planes[plane].length < q->plane_sizes[plane])
So we shouldn't clear the pix->sizeimage and also shouldn't re-calculate
the pix->sizeimage in soc_mbus_image_size() in JPEG mode
We also shouldn't re-calculate pix->bytesperline:
ret = soc_mbus_bytes_per_line(pix->width, xlate->host_fmt);
if (ret < 0)
return ret;
pix->bytesperline = max_t(u32, pix->bytesperline, ret);
pix->bytesperline also should be set by the user or by the driver's
try_fmt() implementation.
Change-Id: I700690a2287346127a624b5260922eaa5427a596
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On i.MX27 two clocks are required: emma-ipg and emma-ahb. The ahb clock
has to be requested using both a device and a connection ID.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
[g.liakhovetski@gmx.de: rebase to the current media tree]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch checks the state of the buffer when calling .buf_init() method.
This is needed for the USERPTR buffer type, because in that case
.buf_init() is called every time a buffer is queued, and not only once
during the preparation stage, like in the MMAP case. Without this check
buffers get initialised repeatedly, which also leads to the allocation
of new DMA descriptors, of which there is only a final relatively small
number available. Both MMAP and USERPTR methods were successfully tested.
Signed-off-by: Alex Gershgorin <alexg@meprolight.com>
[g.liakhovetski@gmx.de: remove mx3_camera_buffer::state completely]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* mos7840 driver was using multiple of HZ for the timeout handed off to
usb_control_msg(). Changed the timeout to use msecs instead.
* Remove unused WAIT_FOR_EVER definition
Signed-off-by: Mark Ferrell <mferrell@uplogix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ZTE (Vodafone) K5006-Z use the following
interface layout:
00 DIAG
01 secondary
02 modem
03 networkcard
04 storage
Ignoring interface #3 which is handled by the qmi_wwan
driver.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_open() can complete before register_netdev() returns.
Fix vmxnet3_probe_device() to support this.
Signed-off-by: Steve Hodgson <steve@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid a crash caused by the scmnd->scsi_done(scmnd) call in
srp_process_rsp() being invoked with scsi_done == NULL. This can
happen if a reply is received during or after a command abort.
Reported-by: Joseph Glanville <joseph.glanville@orionvm.com.au>
Reference: http://marc.info/?l=linux-rdma&m=134314367801595
Cc: <stable@vger.kernel.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Convert a 0 error return code to a negative one, as returned elsewhere
in the function.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Correct spelling typos in comments in drivers/infiniband.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit dbf0e4c (PCI: EHCI: fix crash during suspend on ASUS
computers) added a workaround for an ASUS suspend issue related to
USB EHCI and a bug in a number of ASUS BIOSes that attempt to shut
down the EHCI controller during system suspend if its PCI command
register doesn't contain 0 at that time.
It turns out that the same workaround is necessary in the analogous
hibernation code path, so add it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=45811
Reported-and-tested-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
If a PCI device is put into D3_cold by acpi_bus_set_power(),
the message printed by acpi_pci_set_power_state() says that its
power state has been changed to D4, which doesn't make sense.
In turn, if the device is put into D3_hot, the message simply
says "D3" without specifying the variant of the D3 state.
Fix this by using the pci_power_name() macro for printing the state
name instead of building it from the numeric value corresponding to
the given state directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It seems commit 2098e95ce9 (regulator: twl:
adapt twl-regulator driver to dt) accidentally deleted VINTANA1. Also
the same commit defines VINTANA2 twice with TWL4030_ADJUSTABLE_LDO and
TWL4030_FIXED_LDO. This patch changes the fixed one to be VINTANA1.
I noticed this when auditing my N900 boot logs. I could not notice any
change in device behaviour, though, except that the boot logs are now
like before:
...
[ 0.282928] VDAC: 1800 mV normal standby
[ 0.284027] VCSI: 1800 mV normal standby
[ 0.285400] VINTANA1: 1500 mV normal standby
[ 0.286865] VINTANA2: 2750 mV normal standby
[ 0.288208] VINTDIG: 1500 mV normal standby
[ 0.289978] VSDI_CSI: 1800 mV normal standby
...
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/nve0/fifo: add support for the flip completion swmthd
Daniel Vetter writes:
"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a
Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power). It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
John W. Linville says:
====================
Alexey Khoroshilov provides a potential memory leak in rndis_wlan.
Bob Copeland gives us an ath5k fix for a lockdep problem.
Dan Carpenter fixes a signedness mismatch in at76c50x.
Felix Fietkau corrects a regression caused by an earlier commit that can
lead to an IRQ storm.
Lorenzo Bianconi offers a fix for a bad variable initialization in ath9k
that can cause it to improperly mark decrypted frames.
Rajkumar Manoharan fixes ath9k to prevent the btcoex time from running
when the hardware is asleep.
The remainder are Bluetooth fixes, about which Gustavo says:
"Here goes some fixes for 3.6-rc1, there are a few fix to
thte inquiry code by Ram Malovany, support for 2 new devices,
and few others fixes for NULL dereference, possible deadlock
and a memory leak."
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy noticed that with CONFIG_INET turned off, the following build
errors happen:
ERROR: "register_inetaddr_notifier" [drivers/staging/csr/csr_wifi.ko] undefined!
ERROR: "unregister_inetaddr_notifier" [drivers/staging/csr/csr_wifi.ko] undefined!
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3902a37028 (staging: comedi:
refactor comedi_device_attach() a bit) by yours truly introduced an
inverted logic bug in comedi_device_attach() for the case where the
driver expects the device to be configured by driver name rather than
board name. The result of a strcmp() is being tested incorrectly. Fix
it.
Thanks to Stephen N Chivers for discovering the bug and suggesting the
fix.
Cc: <stable@vger.kernel.org> # 3.5.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b63b70d877 ("IPoIB: Use a private hash table for path lookup
in xmit path") introduced a bug where in ipoib_neigh_free() (which is
called from a few errors flows in the driver), rcu_dereference() is
invoked with the wrong pointer object, which results in a crash.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit b63b70d877 ("IPoIB: Use a private hash table for path lookup
in xmit path") introduced a bug where in ipoib_cm_destroy_tx() a CM
object is moved between lists without any supported locking. Under a
stress test, this eventually leads to list corruption and a crash.
Previously when this routine was called, callers were taking the
device priv lock. Currently this function is called from the RCU
callback associated with neighbour deletion. Fix the race by taking
the same lock we used to before.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Take advantage of the matching macros to make the device id
list easier to read and maintain.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 6 new devices and one modified device, based on
information from laptop vendor Windows drivers.
Sony provides a driver with two new devices using
a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The
Sony driver also adds a non-standard QMI/net
interface to the already supported 1199:9011
Gobi device. We do not know whether this is an
alternate interface number or an additional
interface which might be present, but that doesn't
really matter.
Lenovo provides a driver supporting 4 new devices:
- MC7770 (1199:901b) with standard Gobi 2k+ layout
- MC7700 (0f3d:68a2) with layout similar to MC7710
- MC7750 (114f:68a2) with layout similar to MC7710
- EM7700 (1199:901c) with layout similar to MC7710
Note regaring the three devices similar to MC7710:
The Windows drivers only support interface #8 on these
devices. The MC7710 can support QMI/net functions on
interface #19 and #20 as well, and this driver is
verified to work on interface #19 (a firmware bug is
suspected to prevent #20 from working).
We do not enable these additional interfaces until they
either show up in a Windows driver or are verified to
work in some other way. Therefore limiting the new
devices to interface #8 for now.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver support many composite USB devices where the
interface class/subclass/protocol provides no information
about the interface function. Interfaces with different
functions may all use ff/ff/ff, like this example of
a device with three serial interfaces and three QMI/wwan
interfaces:
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1199 ProdID=68a2 Rev= 0.06
S: Manufacturer=Sierra Wireless, Incorporated
S: Product=MC7710
S: SerialNumber=3581780xxxxxx
C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Instead of class/subclass/protocol the vendor use fixed
interface numbers for each function, and the Windows
drivers use these numbers to match driver and function.
The driver has had its own interface number whitelisting
code to simulate this functionality. Replace this with
generic interface number matching now that the USB subsystem
support is there. This
- removes the need for a driver_info structure per
interface number,
- avoids running the probe function for unsupported
interfaces, and
- simplifies the code.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although this doesn't matter actually, because netpoll_tx_running()
doesn't use the parameter, the code will be more readable.
For team_dev_queue_xmit() we have to move it down to avoid
compile errors.
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the previous patch applied, __netpoll_cleanup() is non-block now,
so we don't need to release the spin_lock before calling it.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the previous patch, slave_disable_netpoll() and __netpoll_cleanup()
may be called with read_lock() held too, so we should make them
non-block, by moving the cleanup and kfree() to call_rcu_bh() callbacks.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When invalidating the TLBs it is documentated as requiring a post-sync
write. Failure to do so seems to result in a GPU hang.
Exposure to this hang on IVB seems to be a result of removing the extra
stalls required for SNB pipecontrol workarounds:
commit 6c6cf5aa9c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 20 18:02:28 2012 +0100
drm/i915: Only apply the SNB pipe control w/a to gen6
Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).
Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP is tons of fun. It turns out that at least the new MacBook Air 5,1
model absolutely doesn't like the new force vdd dance we've introduced
in
commit 6cb49835da
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun May 20 17:14:50 2012 +0200
drm/i915: enable vdd when switching off the eDP panel
But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.
Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.
For reference the old bug, which hopefully doesn't get broken by this:
https://bugzilla.kernel.org/show_bug.cgi?id=43163
In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.
v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.
v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671
Tested-by: Roberto Romer <sildurin@gmail.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Tested-by: Keith Packard <keithp@keithp.com>
Cc: stable@vger.kernel.org
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull s390 patches from Martin Schwidefsky:
"Included are bug fixes and a patch to enable system call filtering
with BPF."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/compat: fix mmap compat system calls
s390/compat: fix compat wrappers for process_vm system calls
s390: do not clobber personality flags in sys_32_personality()
s390/seccomp: add support for system call filtering using BPF
s390/sclp_sdias: Add missing break and "fall through"
s390/mm: remove MAX_PHYSADDR_BITS define
Pull drm fixes from Dave Airlie:
"Radeon and intel fixes mostly, one fix to the mgag200 driver to not
hang on certain server variants."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (32 commits)
drm/radeon: fix typo in function header comment
drm/radeon/kms: implement timestamp userspace query (v2)
drm/radeon/kms: add MSAA texture support for r600-evergreen
drm/radeon/kms: reorder code in r600_check_texture_resource
drm/radeon: fence virtual address and free it once idle v4
drm/radeon: fix some missing parens in asic macros
drm/radeon: add some new SI pci ids
drm/radeon: fix ordering in pll picking on dce4+
drm/radeon: do not reenable crtc after moving vram start address
drm/radeon: fix bank tiling parameters on cayman
drm/radeon: fix bank tiling parameters on evergreen
drm/radeon: fix bank tiling parameters on SI
drm/radeon: properly handle crtc powergating
drm/radeon: properly handle SS overrides on TN (v2)
drm/radeon/dce4+: set a more reasonable cursor watermark
drm/radeon: fix handling for ddc type 5 on combios
drm/mgag200: fix G200ER pll picking algorithm
drm/edid: Fix potential memory leak in edid_load()
drm/udl: Use ERR_CAST inlined function instead of ERR_PTR(PTR_ERR(.. [1]
drm/radeon/kms: allow "invalid" DB formats as a means to disable DB
...
Commit 7212157267 ("GPIO: gpio-pxa: fix devicetree functions") added an
"xlate" function pointer to the irq_domain_ops, but this function is nor
declared or defined anywhere when CONFIG_OF is disabled, causing the
build error:
drivers/gpio/gpio-pxa.c:532:11: error: 'irq_domain_xlate_twocell' undeclared here (not in a function)
Extending the DT-only code section to cover the irq_domain_ops and the
pxa_gpio_dt_ids solves this problem and makes it clearer which code is
actually used without DT.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fix is a backport from the reworked nouveau driver. It masks off the
engines we're not expecting to use before attempting a channel kickoff.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The copy engine exhibits random memory corruption in at least one case, the
GeForce 320M (nv50, 0xaf) in the MacBookAir3,1.
This patch omits creating the engine for the specific chipset, falling back
to M2MF, which kills the symptoms.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes screen being black after changing performance level.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@vger.kernel.org [3.5+]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
At least partially fixes DP output detection on W530. Not sure if more
issues remain, or if my adaptor is just behaving weirdly (it does that
sometimes).
In any case, this patch is necessary.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It is possible for asynchronous RDMA_CM_EVENT_ESTABLISHED events to be
generated with ctx->uid == 0, because ucma_set_event_context() copies
ctx->uid to the event structure outside of ctx->file->mut. This leads
to a crash in the userspace library, since it gets a bogus event.
Fix this by taking the mutex a bit earlier in ucma_event_handler.
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Sean Hefty <Sean.Hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
ath_rx_tasklet() calls ath9k_rx_skb_preprocess() and ath9k_rx_skb_postprocess()
in a loop over the received frames. The decrypt_error flag is
initialized to false
just outside ath_rx_tasklet() loop. ath9k_rx_accept(), called by
ath9k_rx_skb_preprocess(),
only sets decrypt_error to true and never to false.
Then ath_rx_tasklet() calls ath9k_rx_skb_postprocess() and passes
decrypt_error to it.
So, after a decryption error, in ath9k_rx_skb_postprocess(), we can
have a leftover value
from another processed frame. In that case, the frame will not be marked with
RX_FLAG_DECRYPTED even if it is decrypted correctly.
When using CCMP encryption this issue can lead to connection stuck
because of CCMP
PN corruption and a waste of CPU time since mac80211 tries to decrypt an already
deciphered frame with ieee80211_aes_ccm_decrypt.
Fix the issue initializing decrypt_error flag at the begging of the
ath_rx_tasklet() loop.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
i2c_add_adapter() may do i2c transfers on the bus to detect supported
devices. Therefore the adapter needs to be all set before adding it. This
was not the case for the bit-banging fallback, resulting in an oops if the
device detection GMBUS transfers timed out. Fix the issue by calling
i2c_add_adapter() only after intel_gpio_setup().
LKML-Reference: <5021F00B.7000503@ionic.de>
Tested-by: Mihai Moldovan <ionic@ionic.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Returns a snapshot of the GPU clock counter. Needed
for certain OpenGL extensions.
v2: agd5f
- address Jerome's comments
- add function documentation
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Most of the checking seems to be in place already. As you can see,
log2(number of samples) resides in LAST_LEVEL.
This is required for MSAA support (namely for depth-stencil resolve and
blitting between MSAA resources).
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Virtual address need to be fenced to know when we can safely remove it.
This patch also properly clear the pagetable. Previously it was
serouisly broken.
Kernel 3.5/3.4 need a similar patch but adapted for difference in mutex locking.
v2: For to update pagetable when unbinding bo (don't bailout if
bo_va->valid is true).
v3: Add kernel 3.5/3.4 comment.
v4: Fix compilation warnings.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
No functional change, but re-order the cases so they
evaluate properly due to the way the DCE macros work.
Noticed by kallisti5 on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It seems we can not update the crtc scanout address. After disabling
crtc, update to base address do not take effect after crtc being
reenable leading to at least frame being scanout from the old crtc
base address. Disabling crtc display request lead to same behavior.
So after changing the vram address if we don't keep crtc disabled
we will have the GPU trying to read some random system memory address
with some iommu this will broke the crtc engine and will lead to
broken display and iommu error message.
So to avoid this, disable crtc. For flicker less boot we will need
to avoid moving the vram start address.
This patch should also fix :
https://bugs.freedesktop.org/show_bug.cgi?id=42373
Cc: <stable@vger.kernel.org>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
The sixteen bank case wasn't handled here, leading to GPU
crashes because of userspace miscalculation.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to make sure the crtc is gated on before modesetting.
Explicitly gate the crtc on in prepare() and set a flag
so that the dpms functions don't gate it off during
mode set.
Noticed by sylware on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The IntegratedSystemInfo table changed versions
on TN. Update the SS override lookup to handle it.
v2: fix copy-paste typo.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set a more reasonable default cursor watermark. The
recommended default value is 4. This should reduce
urgency requests to the MC form the display hw.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The call to spi_unregister_master() in the device remove function frees device
memory, and with it any device local data. However, device local data is still
accessed after the call to spi_unregister_master().
Acquire a reference to the SPI device and release it after cleanup is complete
to solve the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
bfe4c041 "leds: convert Renesas TPU LED driver to devm_kzalloc() and
cleanup error exit path" introduced a possible case in which r_tpu_probe
calls iounmap on a wild pointer. This changes the one case that was
missed in the same way as the other error paths.
Without this patch, building kota2_defconfig results in:
drivers/leds/leds-renesas-tpu.c: In function 'r_tpu_probe':
drivers/leds/leds-renesas-tpu.c:246:6: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
drivers/leds/leds-renesas-tpu.c:308:17: warning: 'p' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
This reverts commit a0193cbee0.
The problem with the original commit was that it caused a warning with
the MMC trigger calling del_timer_sync from hard-irq context.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Reported-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Pull networking changes from David Miller:
"Most importantly this should cure the ipv4-mapped ipv6 socket TCP
crashes some people were seeing, otherwise:
1) Fix e1000e autonegotiation handling regression, from Tushar Dave.
2) Fix TX data corruption race on e1000e down, also from Tushar Dave.
3) Fix bfin_sir IRDA driver build, from Sonic Zhang.
4) AF_PACKET mmap() tests a flag in the TX ring shared between
userspace and the kernel for an internal consistency check. It
really shouldn't do this to validate the kernel's own behavior
because the user can corrupt it to be any value at all. From
Daniel Borkmann.
5) Fix TCP metrics leak on netns dismantle, from Eric Dumazet.
6) Orphan the anonymous TCP socket from the SKB in
ip_send_unicast_reply() so that the rest of the stack needn't see
it. Otherwise we get selinux problems of all sorts, from Eric
Dumazet.
This is the best way to fix this since the socket is just a place
holder for sending packets in a context where we have no real
socket at all.
7) Fix TUN detach crashes, from Stanislav Kinsbursky.
8) dev_set_alias() leaks memory on krealloc() failure, from Alexey
Khoroshilov.
9) FIB trie must use call_rcu() not call_rcu_bh(), because this code
is not universally invoked from software interrupts. From Eric
Dumazet.
10) PPTP looks up ipv4 routes with the wrong network namespace, fix
from Gao Feng."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
bnx2x: Fix compiler warnings
af_packet: remove BUG statement in tpacket_destruct_skb
macvtap: rcu_dereference outside read-lock section
codel: refine one condition to avoid a nul rec_inv_sqrt
ixgbe: add missing braces
ipv4: fix ip_send_skb()
net: tcp: ipv6_mapped needs sk_rx_dst_set method
ipv4: tcp: unicast_sock should not land outside of TCP stack
bnx2x: Fix recovery flow cleanup during probe
bnx2x: fix unload previous driver flow when flr-capable
tun: don't zeroize sock->file on detach
igb: Fix register defines for all non-82575 hardware
e1000e: fix panic while dumping packets on Tx hang with IOMMU
igb: fix panic while dumping packets on Tx hang with IOMMU
tcp: must free metrics at net dismantle
net/stmmac: mark probe function as __devinit
lpc_eth: remove obsolete ifdefs
net/core: Fix potential memory leak in dev_set_alias()
cdc-phonet: Don't leak in usbpn_open
batman-adv: Fix mem leak in the batadv_tt_local_event() function
...
Pull tcm_vhost level target fabric driver from Nicholas Bellinger:
"Here is the PULL request for the initial merge of tcm_vhost based on
RFC-v5 code with MST's ACK appended to the initial merge commit."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcm_vhost: Initial merge for vhost level target fabric driver
Fix the following compiler warnings:
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:2908:3: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
- drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c:1709:7: warning: comparison
of distinct pointer types lacks a cast [enabled by default]
Signed-off-by: Joren Van Onder <joren.vanonder@gmail.com>
Acked-By: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu_dereference occurs in update section. Replacement by
rcu_dereference_protected in order to prevent lockdep
complaint.
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix a resource leak in the SCH driver
- Fix the register address calculation in the MSIC driver
- Fix the PXA driver's devicetree functions
- Delete redundant shadow variable leftovers in the MXC driver
- Specify the GPIO base for the device tree probe in the MXC driver
- Add a modalias for the i.MX driver
- Fix off-by-one bug in the Samsung driver
- Fix erroneous errorpath in the Langwell driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=WsZj
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
- Fix a resource leak in the SCH driver
- Fix the register address calculation in the MSIC driver
- Fix the PXA driver's devicetree functions
- Delete redundant shadow variable leftovers in the MXC driver
- Specify the GPIO base for the device tree probe in the MXC driver
- Add a modalias for the i.MX driver
- Fix off-by-one bug in the Samsung driver
- Fix erroneous errorpath in the Langwell driver
* tag 'gpio-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
drivers/gpio/gpio-langwell.c: fix error return code
gpio: samsung: Fix off-by-one bug in gpio addresses
ARM: dts: imx: add alias for gpio
gpio/mxc: specify gpio base for device tree probe
gpio/mxc: remove redundant shadow variables initialization
GPIO: gpio-pxa: fix devicetree functions
gpio: msic: Fix calculating register address in msic_gpio_to_oreg()
gpio-sch: Fix leak of resource
* Fix for two recent regressions in the generic PM domains framework.
* Revert of a commit that introduced a resume regression and is conceptually
incorrect in my opinion.
* Fix for a return value in pcc-cpufreq.c from Julia Lawall.
* RTC wakeup signaling fix from Neil Brown.
* Suppression of compiler warnings for CONFIG_PM_SLEEP unset in ACPI,
platform/x86 and TPM drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=lo6A
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
- Fix for two recent regressions in the generic PM domains framework.
- Revert of a commit that introduced a resume regression and is
conceptually incorrect in my opinion.
- Fix for a return value in pcc-cpufreq.c from Julia Lawall.
- RTC wakeup signaling fix from Neil Brown.
- Suppression of compiler warnings for CONFIG_PM_SLEEP unset in ACPI,
platform/x86 and TPM drivers.
* tag 'pm-for-3.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tpm_tis / PM: Fix unused function warning for CONFIG_PM_SLEEP
platform / x86 / PM: Fix unused function warnings for CONFIG_PM_SLEEP
ACPI / PM: Fix unused function warnings for CONFIG_PM_SLEEP
Revert "NMI watchdog: fix for lockup detector breakage on resume"
PM: Make dev_pm_get_subsys_data() always return 0 on success
drivers/cpufreq/pcc-cpufreq.c: fix error return code
RTC: Avoid races between RTC alarm wakeup and suspend.
These are a bunch of bug fixes that came in after the merge window and
one update for the MAINTAINERS file. The largest part of the fixes
are patches that address bugs found by building all the ARM defconfig
files. There are a lot more warnings that we have patches for, but
the others are either still under discussion or are harmless and
do not cause actual problems besides making the build slightly noisy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=TmsX
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc bug fixes from Arnd Bergmann:
"These are a bunch of bug fixes that came in after the merge window and
one update for the MAINTAINERS file.
The largest part of the fixes are patches that address bugs found by
building all the ARM defconfig files. There are a lot more warnings
that we have patches for, but the others are either still under
discussion or are harmless and do not cause actual problems besides
making the build slightly noisy."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: davinci: remove broken ntosd2_init_i2c
ARM: s3c24xx: enable CONFIG_BUG for tct_hammer
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
ARM: imx: gpmi-nand depends on mxs-dma
ARM: integrator: include <linux/export.h>
ARM: s3c24xx: use new PWM driver
ARM: sa1100: include linux/io.h in hackkit leds code
Input: eeti_ts: pass gpio value instead of IRQ
ARM: pxa: remove irq_to_gpio from ezx-pcap driver
ARM: tegra: more regulator fixes for Harmony
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
ARM: kirkwood: fix typo in Makefile.boot
i.MX27: Fix emma-prp and csi clocks.
ARM: integrator: use clk_prepare_enable() for timer
MAINTAINERS: update entry for Linus Walleij
...
This removes the need for shark_led_work to take the v4l2 lock.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recent kernels properly clear the usb intfdata pointer when another
driver fails to bind (in the radio-shark* case the usbhid driver would try
to bind first.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the error
drivers/usb/core/hub.c:3753: undefined reference to `usb_speed_string'
seen in various random configurations.
Cc: Sean Young <sean@mess.org>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct v4l2_hw_freq_seek has two new fields that weren't printed in the
logging function. Added.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When VIDIOC_ENUM_FREQ_BANDS is called for a driver that doesn't supply an
enum_freq_bands op, then it will fall back to reporting a single freq band
based on information from g_tuner or g_modulator.
Due to a bug this is an infinite list since the index field wasn't tested.
This patch fixes this and returns -EINVAL if index != 0.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This has originally been introduced to not oversubscribe the dp links
in
commit 885a5fb5b1
Author: Zhenyu Wang <zhenyuw@linux.intel.com>
Date: Tue Jan 12 05:38:31 2010 +0800
drm/i915: fix pixel color depth setting on eDP
Since then we've fixed up the dp link bandwidth calculation code and
should now automatically fall back to 6bpc dithering. So this is
unnecessary.
Furthermore it seems to break the new MacbookPro with retina display,
hence let's just rip this out.
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Cc: Benoit Gschwind <gschwind@gnu-log.net>
Cc: Francois Rigaut <frigaut@gmail.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Tested-by: Benoit Gschwind <gschwind@gnu-log.net>
Tested-by: Bernhard Froemel <froemel at vmars tuwien.ac.at>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
--
Testing feedback highgly welcome, and thanks for Benoit for finding
out that the bpc computations are busted.
-Daniel
When you reopen the lid on a laptop with PCH, the panel suddenly goes
blank sometimes. It seems because BLC_PWM_CPU_CTL register is cleared
to zero when BLC_PWM_CPU_CTL2 and BLC_PWM_PCH_CTL1 registers are
enabled.
This patch fixes the problem by moving the call of the function setting
BLC_PWM_CPU_CTL after enabling other two registers.
Reported-and-tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just a few fixes for problems found after updating v4l2-compliance to check
the frequency band enumeration.
Note that the i2c driver doesn't fill in bus_info, but since I can't test that
driver I've decided not to fix that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Buffers marked as erroneous are recycled immediately by the driver if
the nodrop module parameter isn't set. The buffer payload size is reset
to 0, but the buffer bytesused field isn't. This results in the buffer
being immediately considered as complete, leading to an infinite loop in
interrupt context.
Fix the problem by resetting the bytesused field when recycling the
buffer.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jayakrishnan Memana <jayakrishnan.memana@maxim-ic.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If CONFIG_VLAN_8021Q is not set, then vlan_dev_real_dev() just goes BUG(),
so we shouldn't call it unless we're actually dealing with a VLAN netdev.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch adds missing braces around the 10gig link check to include the check for KR support.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Sascha Wildner <saw@online.de>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial patch adds a short description for SERIAL_CLPS711X Kconfig
entry, removes excess dependence on the ARM-platform (this is done
globally for the platform), allows the driver to be compiled by default
and removes unnecessary description about GRUB and LILO, because these
bootloaders do not supported this platform.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue introduced by patch:
72c973d usb: gadget: add usb_endpoint_descriptor to struct usb_ep
Without this patch we see a kworker taking 100% CPU, after this sequence:
- Connect gadget to a windows host
- load g_ether
- ifconfig up <ip>; ifconfig down; ifconfig up
- ping <windows host>
The "ifconfig down" results in calling eth_stop(), which will call
usb_ep_disable() and, if the carrier is still ok, usb_ep_enable():
usb_ep_disable(link->in_ep);
usb_ep_disable(link->out_ep);
if (netif_carrier_ok(net)) {
usb_ep_enable(link->in_ep);
usb_ep_enable(link->out_ep);
}
The ep should stay enabled, but will not, as ep_disable set the desc
pointer to NULL, therefore the subsequent ep_enable will fail. This leads
to permanent rescheduling of the eth_work() worker as usb_ep_queue()
(called by the worker) will fail due to the unconfigured endpoint.
We fix this issue by saving the ep descriptors and re-assign them before
usb_ep_enable().
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing implementation of tegra_ehci_remove() calls
usb_put_hcd(hcd) first and then iounmap(hcd->regs).
usb_put_hcd() implementation calls hcd_release()
which frees up memory allocated for hcd.
As iounmap is trying to unmap hcd->regs, after hcd
getting freed up, warning messages were observed during
unload of USB.
Hence fixing it.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One line fix after 'struct ehci_regs' definition was changed
in commit a46af4ebf9 (USB: EHCI: define
extension registers like normal ones).
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If renesas_usbhs is probed as autonomy mode,
phy reset should be called after power resumed,
and manual cold-plug should be called with slight delay.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
suspend/resume will failed on renesas_usbhs without this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot unconditionally access any usb-serial port specific
data from the interface driver. Both supending and resuming
may happen after the port has been removed and portdata is
freed.
Treat ports with no portdata as closed ports to avoid a NULL
pointer dereference on resume. No need to kill URBs for
removed ports on suspend, avoiding the same NULL pointer
reference there.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some usb-serial drivers may access port data in their suspend/
resume functions. Such drivers must always verify the validity
of the data as both suspend and resume can be called both before
usb_serial_device_probe and after usb_serial_device_remove.
But the port data may be invalidated during port_probe and
port_remove. This patch prevents the race against suspend and
resume by disabling suspend while port_probe or port_remove is
running.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Use the buffer content length as opposed to the total buffer size. This can
be a real problem when using the mos7840 as a usb serial-console as all
kernel output is truncated during boot.
Signed-off-by: Mark Ferrell <mferrell@uplogix.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During suspend, the device will be moved to FULLSLEEP state.
As btcoex is never been stopped, the btcoex timer is running
and tries to access hw on fullsleep state. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This return holds the number of bytes transfered (1 byte) or a negative
error code. The type should be int instead of u8.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not leak memory by updating pointer with potentially NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit b74713d04e
"ath9k: Handle fatal interrupts properly" introduced a race condition, where
IRQs are being left enabled, however the irq handler returns IRQ_HANDLED
while the reset is still queued without addressing the IRQ cause.
This leads to an IRQ storm that prevents the system from even getting to
the reset code.
Fix this by disabling IRQs in the handler without touching intr_ref_cnt.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The usb message must be saved also in case the USB endpoint is not a
control endpoint (i.e., "endpoint 0"), otherwise in some circumstances
we don't have a payload in case of error.
The patch has been created by tracing with usbmon the different error
messages generated by this driver with respect to the ehci-hcd driver.
Signed-off-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Tested-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit 354ab8567a titled
"Fix OMAP EHCI suspend/resume failure (i693)" is causing
the usb hub and device detection fails in beagle XM
causeing NFS not functional. This affects the core retention too.
The same commit logic needs to be revisted adhering to hwmod and
device tree framework.
for now, this commit id 354ab8567a
titled "Fix OMAP EHCI suspend/resume failure (i693)" reverted.
This patch is validated on BeagleXM with NFS support over
usb ethernet and USB mass storage and other device detection.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: stable <stable@vger.kernel.org> # 3.5
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit "5e0aa49 usb: chipidea: use generic map/unmap routines",
the udc part of the chipidea driver needs the generic usb gadget helper
functions. If the chipidea driver with udc support is built into the
kernel and usb gadget is built a module, the linking of the kernel
fails with:
drivers/built-in.o: In function `_hardware_dequeue':
drivers/usb/chipidea/udc.c:527:
undefined reference to `usb_gadget_unmap_request'
drivers/usb/chipidea/udc.c:1269:
undefined reference to `usb_gadget_unmap_request'
drivers/usb/chipidea/udc.c:1821:
undefined reference to `usb_del_gadget_udc'
drivers/usb/chipidea/udc.c:443:
undefined reference to `usb_gadget_map_request'
drivers/usb/chipidea/udc.c:1774:
undefined reference to `usb_add_gadget_udc'
This patch changes the dependencies, so that udc support can only be
activated if the linux gadget support (USB_GADGET) is builtin or both
chipidea driver and USB_GADGET are modular. Same dependencies for the
chipidea host support and the linux host side USB support (USB).
While there, fix the indention of chipidea the help text.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In this patch, we add new declarations into option.c to support the new
interfaces of Huawei Data Card devices. And at the same time, remove the
redundant declarations from option.c.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds VID/PID for Kondo Kagaku Co. Ltd. Serial USB Adapter
interface:
http://www.kondo-robot.com/EN/wp/?cat=28
Tested by controlling an RCB3 board using libRCB3.
Signed-off-by: Ozan Çağlayan <ozancag@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to a compiler warning, the tpm_tis_resume() function is not
used for CONFIG_PM_SLEEP unset, so add a #ifdef to prevent it from
being built in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
According to compiler warnings, quite some suspend/resume functions
in platform x86 drivers are not used for CONFIG_PM_SLEEP unset, so
add #ifdefs to prevent them from being built in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
According to compiler warnings, several suspend/resume functions
in ACPI drivers are not used for CONFIG_PM_SLEEP unset, so add
#ifdefs to prevent them from being built in that case.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The original code was misported from the X driver,
a) an int went to unsigned int, breaking the downward counting testm code
b) the port did the vco/computed clock bits completely wrong.
This fixes an infinite loop on modprobe on some Dell servers with the G200ER
chipset variant.
Found in internal testing.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Do not leak memory by updating pointer with potentially
NULL realloc return value.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These patches all fix bugs that were newly introduced in v3.6-rc1
and found because they cause a gcc warning with one of the ARM
defconfigs. Most of them are harmless, but since we're trying
to get rid of all warnings eventually, we can start with the ones
that were not there before.
* testing/new-warnings:
omap-rng: fix use of SIMPLE_DEV_PM_OPS
spi/s3c64xx: improve error handling
mtd/omap2: fix dmaengine_slave_config error handling
gpio: em: do not discard em_gio_irq_domain_cleanup
ARM: exynos: exynos_pm_add_dev_to_genpd may be unused
usb/ohci-omap: remove unused variable
mfd/asic3: fix asic3_mfd_probe return value
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
omap_rng_suspend and omap_rng_resume are unused if CONFIG_PM is enabled
but CONFIG_PM_SLEEP is disabled. I found this while building all defconfig
files on ARM. It's not clear to me if this is the right solution, but
at least it makes the code consistent again.
Without this patch, building omap1_defconfig results in:
drivers/char/hw_random/omap-rng.c:165:12: warning: 'omap_rng_suspend' defined but not used [-Wunused-function]
drivers/char/hw_random/omap-rng.c:171:12: warning: 'omap_rng_resume' defined but not used [-Wunused-function]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kevin Hilman <khilman@ti.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
When a device tree definition os an s3c64xx SPI master is missing
a "controller-data" subnode, the newly added s3c64xx_get_slave_ctrldata
function might use uninitialized memory in place of that node,
which was correctly reported by gcc.
Without this patch, building s3c6400_defconfig results in:
drivers/spi/spi-s3c64xx.c: In function 's3c64xx_get_slave_ctrldata.isra.25':
drivers/spi/spi-s3c64xx.c:841:5: warning: 'data_np' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Jaswinder Singh <jaswinder.singh@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
The newly added dmaengine support in the omap2 nand driver
potentially causes an undefined return value from the
omap_nand_probe function when dmaengine_slave_config
reports an error. Let's handle this by returning the
same error back to the caller.
Without this patch, building omap2plus_defconfig results in:
drivers/mtd/nand/omap2.c: In function 'omap_nand_probe':
drivers/mtd/nand/omap2.c:1154:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Grazvydas Ignotas <notasas@gmail.com>
The newly added gpio-em driver marks its em_gio_irq_domain_cleanup
function as __devexit, which would lead to that function being
discarded in case CONFIG_HOTPLUG is disabled. However, the function
is also called by the error handling logic em_gio_probe, which
would cause a jump into a NULL pointer if it was removed from the
kernel or module.
Without this patch, building kzm9d_defconfig results in:
WARNING: drivers/gpio/built-in.o(.devinit.text+0x330): Section mismatch in reference from the function em_gio_probe() to the function .devexit.text:em_gio_irq_domain_cleanup()
The function __devinit em_gio_probe() references
a function __devexit em_gio_irq_domain_cleanup().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
em_gio_irq_domain_cleanup() so it may be used outside an exit section.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
The ACPI tables in the Macbook Air 5,1 define a single IOAPIC with id 2,
but the only remapping unit described in the DMAR table matches id 0.
Interrupt remapping fails as a result, and the kernel panics with the
message "timer doesn't work through Interrupt-remapped IO-APIC."
To fix this, check each IOAPIC for a corresponding IOMMU. If an IOMMU is
not found, do not allow IRQ remapping to be enabled.
v2: Move check to parse_ioapics_under_ir(), raise log level to KERN_ERR,
and add FW_BUG to the log message
v3: Skip check if IOMMU doesn't support interrupt remapping and remove
existing check that the IOMMU count equals the IOAPIC count
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
During probe, every function probed clears the recovery registers from
all functions on its path - thus signaling that given a future recovery
event, there will be no need to wait for those functions.
This is a flawed behaviour - each function should only be responsible
for its own bit.
Since this registers are handled during the load/unload routines,
this cleanup is removed altogether.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing previous driver unload flow is flawed, causing the probe of
functions reaching the 'uncommon fork' in flr-capable devices to fail.
This patch resolves this, as well as fixing the flow for hypervisors which
disable flr capabilities from functions as they pass them as PDA to VMs,
as we cannot base the flow on the pci configuration space.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a fix for bug, introduced in 3.4 kernel by commit
1ab5ecb90c ("tun: don't hold network
namespace by tun sockets"), which, among other things, replaced simple
sock_put() by sk_release_kernel(). Below is sequence, which leads to
oops for non-persistent devices:
tun_chr_close()
tun_detach() <== tun->socket.file = NULL
tun_free_netdev()
sk_release_sock()
sock_release(sock->file == NULL)
iput(SOCK_INODE(sock)) <== dereference on NULL pointer
This patch just removes zeroing of socket's file from __tun_detach().
sock_release() will do this.
Cc: stable@vger.kernel.org
Reported-by: Ruan Zhijie <ruanzhijie@hotmail.com>
Tested-by: Ruan Zhijie <ruanzhijie@hotmail.com>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS. If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system. Some BIOS will work around this, but not all.
The bug can be avoided if the USB ports are switched back to EHCI on
shutdown. The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.
Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names. One example
is Compulab's mini-desktop, the Intense-PC. Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.
The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.
This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c209 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Denis Turischev <denis@compulab.co.il>
Tested-by: Denis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org
Commit 65f735082d ("regulator: core: Add core support for GPIO controlled
enable lines") introduced enable gpio entry in regulator configuration
structure. Some drivers use '-1' as a placeholder for marking that such
gpio line is not available, because '0' is considered as a valid gpio
number. This patch fixes initialization of such drivers (like MAX8952
on UniversalC210 board), when '-1' is provided as enable gpio pin in the
regulator's platform data.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Hi Greg,
Here's four patches for 3.6. Most are marked for stable as well.
The first one makes the xHCI driver load properly on newer Rensas hosts.
The next two fix issues with the Etron host incorrectly marking short
transfers as successful, and avoiding log warning spam for hosts that
make the same mistake.
The last patch fixes a really nasty xHCI driver bug that could cause
general protection faults when devices stall transfers.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yn5e
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-08-08' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xHCI bug fixes and host quirks.
Hi Greg,
Here's four patches for 3.6. Most are marked for stable as well.
The first one makes the xHCI driver load properly on newer Rensas hosts.
The next two fix issues with the Etron host incorrectly marking short
transfers as successful, and avoiding log warning spam for hosts that
make the same mistake.
The last patch fixes a really nasty xHCI driver bug that could cause
general protection faults when devices stall transfers.
Sarah Sharp
It is not currently possible to build the gpmi-nand driver without
also building the mxs-dma driver. Clarify this Kconfig and enable
both in the defconfig file so we can build it again with both enabled.
drivers/built-in.o: In function `gpmi_dma_filter':
clk-fixed-factor.c:(.text+0xafc18): undefined reference to `mxs_dma_is_apbh'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
The EETI touchscreen asserts its IRQ line as soon as it has data in its
internal buffers. The line is automatically deasserted once all data has
been read via I2C. Hence, the driver has to monitor the GPIO line and
cannot simply rely on the interrupt handler reception.
In the current implementation of the driver, irq_to_gpio() is used to
determine the GPIO number from the i2c_client's IRQ value.
As irq_to_gpio() is not available on all platforms, this patch changes
this and makes the driver ignore the passed in IRQ. Instead, a GPIO is
added to the platform_data struct and gpio_to_irq is used to derive the
IRQ from that GPIO. If this fails, bail out. The driver is only able to
work in environments where the touchscreen GPIO can be mapped to an
IRQ.
Without this patch, building raumfeld_defconfig results in:
drivers/input/touchscreen/eeti_ts.c: In function 'eeti_ts_irq_active':
drivers/input/touchscreen/eeti_ts.c:65:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Cc: linux-input@vger.kernel.org
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
The irq_to_gpio function was removed from the pxa platform
in linux-3.2, and this driver has been broken since.
There is actually no in-tree user of this driver that adds
this platform device, but the driver can and does get enabled
on some platforms.
Without this patch, building ezx_defconfig results in:
drivers/mfd/ezx-pcap.c: In function 'pcap_isr_work':
drivers/mfd/ezx-pcap.c:205:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
It looks like the register defines for DCA were never updated after going from
82575 to 82576. This change addresses that by updating the defines.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch avoids phys_to_virt() by using skb->data and the address of the
pages allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().
This patch avoids phys_to_virt() by making using skb->data and the address
of the pages allocated for Rx.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Presently it's assumed that the irqdomain code handles the irq_desc
allocation for us, but this isn't necessarily the case when we've
pre-allocated IRQs via sparseirq. Previously we had a -EEXIST check in
the code that attempted to trap these cases and simply update them
in-place, but this behaviour was inadvertently lost in the transition to
irqdomains.
This simply restores the previous behaviour, first attempting to let the
irqdomain core fetch the allocation for us, and falling back to an
in-place domain association in the extant IRQ case. Fixes up regressions
on platforms that pre-allocate legacy IRQs (specifically ARM-based
SH-Mobile platforms, as SH stopped pre-allocating vectors some time ago).
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The semantic patch that makes this change is available
in scripts/coccinelle/api/err_cast.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel writes:
"- Regression fixer for an OOPS at boot when i915.ko is built-in and
CONFIG_PM=n, introduce in 3.5 (patch from Hunt Xu)
- Regression fixer for occlusion query failures, the required w/a wasn't
applied in all cases (thanks to Eric for tracking this on down).
- dmar vs. dma_buf imprt fix (Dave Airlie)
- 2 patches to fight down forcewake issues on snb. This is the stuff I've
talked about 2 weeks ago already, it's a minefield. Investigation still
going on, but afaict this is the best we have for now.
- a few minor things to keep coverty&compiler happy (Alan, Davendra,
Stéphane)
- tons of hsw pci ids - this one is a bit late because internal approval
sometimes takes a while, but ppl in charge finally agreed that world+dog
already knows about ult and crw haswell variants ;-)
Wrt regressions I'm aware of:
- the power regression due to semaphores=1. Ben is running around with a
killawatt, unfortunately we have a hard time reproducing this one. And
this /shouldn't/ increase power usage. Ben has turned up a few odds bits
though already.
- the lvds fix in 3.6-rc1 broke a backlight after lid close/open (but can
be resurrected with a modeset cycle). I guess we anger the bios - I'm
still looking into this one.
- gmbus broke edid reading on an odd-ball monitor, we need to fall-back.
Due to vacation (both mine&the reporter's) this is stalling for a final
patch and a tested-by on it. But issue is fully diagnosed."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: correctly order the ring init sequence
drm/i915: add more Haswell PCI IDs
drm/i915: make rc6 in sysfs functions conditional
drm/i915: Workaround hang with BSD and forcewake on SandyBridge
drm/i915: Make intel_panel_get_backlight static.
i915: don't map imported dma-bufs for dmar.
drm/i915: remove unused variable
drm/i915: Don't forget to apply SNB PIPE_CONTROL GTT workaround.
drm/i915: fix forcewake related hangs on snb
i915: Remove silly test
i915: fix error path leak in intel_sdvo_write_cmd
vlv: it might be wise if we initialised the flag value...
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Driver probe functions are generally __devinit so they will be
discarded after initialization for non-hotplug kernels.
This was found by a new warning after patch 6a228452d "stmmac: Add
device-tree support" adds a new __devinit function that is called
from stmmac_pltfr_probe.
Without this patch, building socfpga_defconfig results in:
WARNING: drivers/net/ethernet/stmicro/stmmac/stmmac.o(.text+0x5d4c): Section mismatch in reference from the function stmmac_pltfr_probe() to the function .devinit.text:stmmac_probe_config_dt()
The function stmmac_pltfr_probe() references
the function __devinit stmmac_probe_config_dt().
This is often because stmmac_pltfr_probe lacks a __devinit
annotation or the annotation of stmmac_probe_config_dt is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The #ifdefs regarding CONFIG_ARCH_LPC32XX_MII_SUPPORT and
CONFIG_ARCH_LPC32XX_IRAM_FOR_NET are obsolete since the symbols have been
removed from Kconfig and replaced by devicetree based configuration.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate memory for 'req' with usb_alloc_urb() and then test
'if (!req || rx_submit(pnd, req, GFP_KERNEL | __GFP_COLD))'.
If we enter that branch due to '!req' then there is no problem. But if
we enter the branch due to 'req' being != 0 and the 'rx_submit()' call
being false, then we'll leak the memory we allocated.
Deal with the leak by always calling 'usb_free_urb(req)' when entering
the branch. If 'req' happens to be 0 then the call is harmless, if it
is not 0 then we free the memory we allocated but don't need.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
pptp always use init_net as the net namespace to lookup
route, this will cause route lookup failed in container.
because we already set the correct net namespace to struct
sock in pptp_create,so fix this by using sock_net(sk) to
replace &init_net.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter P Waskiewicz Jr says:
====================
This series contains fixes to the e1000e and igb drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit IREN is replaced by UMOD_IRDA and UMOD_MASK since blackfin 60x added, but
this driver didn't update which will cause bfin_sir build error:
drivers/net/irda/bfin_sir.c:161:9: error: 'IREN' undeclared (first use in this
function)
drivers/net/irda/bfin_sir.c:435:18: error: 'IREN' undeclared (first use in
this function)
drivers/net/irda/bfin_sir.c:521:11: error: 'IREN' undeclared (first use in
this function)
This patch fix it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Acked-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a particularly nasty bug that was revealed by the ring
expansion patches. The bug has been present since the very beginning of
the xHCI driver history, and could have caused general protection faults
from bad memory accesses.
The first thing to note is that a Set TR Dequeue Pointer command can
move the dequeue pointer to a link TRB, if the canceled or stalled
transfer TD ended just before a link TRB. The function to increment the
dequeue pointer, inc_deq, was written before cancellation and stall
support was added. It assumed that the dequeue pointer could never
point to a link TRB. It would unconditionally increment the dequeue
pointer at the start of the function, check if the pointer was now on a
link TRB, and move it to the top of the next segment if so.
This means that if a Set TR Dequeue Point command moved the dequeue
pointer to a link TRB, a subsequent call to inc_deq() would move the
pointer off the segment and into la-la-land. It would then read from
that memory to determine if it was a link TRB. Other functions would
often call inc_deq() until the dequeue pointer matched some other
pointer, which means this function would quite happily read all of
system memory before wrapping around to the right pointer value.
Often, there would be another endpoint segment from a different ring
allocated from the same DMA pool, which would be contiguous to the
segment inc_deq just stepped off of. inc_deq would eventually find the
link TRB in that segment, and blindly move the dequeue pointer back to
the top of the correct ring segment.
The only reason the original code worked at all is because there was
only one ring segment. With the ring expansion patches, the dequeue
pointer would eventually wrap into place, but the dequeue segment would
be out-of-sync. On the second TD after the dequeue pointer was moved to
a link TRB, trb_in_td() would fail (because the dequeue pointer and
dequeue segment were out-of-sync), and this message would appear:
ERROR Transfer event TRB DMA ptr not part of current TD
This fixes bugzilla entry 4333 (option-based modem unhappy on USB 3.0
port: "Transfer event TRB DMA ptr not part of current TD", "rejecting
I/O to offline device"),
https://bugzilla.kernel.org/show_bug.cgi?id=43333
and possibly other general protection fault bugs as well.
This patch should be backported to kernels as old as 2.6.31. A separate
patch will be created for kernels older than 3.4, since inc_deq was
modified in 3.4 and this patch will not apply.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: James Ettle <theholyettlz@googlemail.com>
Tested-by: Matthew Hall <mhall@mhcomputing.net>
Cc: stable@vger.kernel.org
Commit c2e935a7d "USB: move transceiver from ehci_hcd and ohci_hcd to
hcd and rename it as phy" removed the last use of the "ohci" variable
in the usb_hcd_omap_remove function, but left the variable in place
unused.
Without this patch, building omap1_defconfig results in:
In file included from drivers/usb/host/ohci-hcd.c:1013:0:
drivers/usb/host/ohci-omap.c: In function 'usb_hcd_omap_remove':
drivers/usb/host/ohci-omap.c:406:19: warning: unused variable 'ohci' [-Wunused-variable]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Richard Zhao <richard.zhao@freescale.com>
In commit 4f304245b "mfd: Set asic3 DS1WM clock_rate", a possible
path through asic3_mfd_probe was introduced that would lead to
an unpredictable return value, if everything succeeds but there
are pdata->leds is NULL. This was reported correctly by gcc.
Without this patch, building magician_defconfig results in:
drivers/mfd/asic3.c: In function 'asic3_mfd_probe':
drivers/mfd/asic3.c:940:2: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Parsons <lost.distance@yahoo.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Commits 1d5fcfec22 (PM / Domains: Add device domain data reference
counter) and 62d4490294 (PM / Domains: Allow device callbacks to be
added at any time) added checks for the return value of
dev_pm_get_subsys_data(), but those checks were incorrect, because
that function returned 1 on success in some cases.
Since all of the existing users of dev_pm_get_subsys_data() don't use
the positive value returned by it on success, change its definition
so that it always returns 0 when successful.
Reported-by: Heiko Stübner <heiko@sntech.de>
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If an RTC alarm fires just as suspend is happening, it is possible for
suspend to complete and the alarm to be missed.
To avoid the race, we must register the event with the PM core.
As the event is made visible to userspace through a thread which is
only scheduled by the interrupt, we need a pm_stay_awake/pm_relax
pair preventing suspend from the interrupt until the thread completes
its work.
This makes the pm_wakeup_event() call in cmos_interrupt unnecessary as
it provides suspend protection for all RTCs that use rtc_update_irq.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pull networking fixes from David Miller:
1) Missed rcu_assign_pointer() in mac80211 scanning, from Johannes
Berg.
2) Allow devices to limit the number of segments that an individual
TCP TSO packet can use at a time, to deal with device and/or driver
specific limitations. From Ben Hutchings.
3) Fix unexpected hard IPSEC expiration after setting the date. From
Fan Du.
4) Memory leak fix in bxn2x driver, from Jesper Juhl.
5) Fix two memory leaks in libertas driver, from Daniel Drake.
6) Fix deref of out-of-range array index in packet scheduler generic
actions layer. From Hiroaki SHIMODA.
7) Fix TX flow control errors in mlx4 driver, from Yevgeny Petrilin.
8) Fix CRIS eth_v10.c driver build, from Randy Dunlap.
9) Fix wrong SKB freeing in LLC protocol layer, from Sorin Dumitru.
10) The IP output path checks neigh lookup errors incorrectly, it needs
to use IS_ERR(). From Vasiliy Kulikov.
11) An estimator leak leads to deref of freed memory in timer handler,
fix from Hiroaki SHIMODA.
12) TCP early demux in ipv6 needs to use DST cookies in order to
validate the RX route properly. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
net: ipv6: fix TCP early demux
net: Use PTR_RET rather than if(IS_ERR(.. [1]
net_sched: act: Delete estimator in error path.
ip: fix error handling in ip_finish_output2()
llc: free the right skb
ixp4xx_eth: fix ptp_ixp46x build failure
drivers/atm/iphase.c: fix error return code
tcp_output: fix sparse warning for tcp_wfree
drivers/net/phy/mdio-mux-gpio.c: drop devm_kfree of devm_kzalloc'd data
batman-adv: select an internet gateway if none was chosen
mISDN: Bugfix for layer2 fixed TEI mode
igb: don't break user visible strings over multiple lines in igb_ethtool.c
igb: correct hardware type (i210/i211) check in igb_loopback_test()
igb: Fix for failure to init on some 82576 devices.
cris: fix eth_v10.c build error
cdc-ncm: tag Ericsson WWAN devices (eg F5521gw) with FLAG_WWAN
isdnloop: fix and simplify isdnloop_init()
hyperv: Move wait completion msg code into rndis_filter_halt_device()
net/mlx4_core: Remove port type restrictions
net/mlx4_en: Fixing TX queue stop/wake flow
...
- Move MXS pinctrl registration to poscore_initcall
- Fix up various devm_* managed resources code paths
- Fix one function group in the Nomadik driver
- Update MAINTAINERS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJQInDjAAoJEEEQszewGV1zd/EQAJomDXod98OvoZXwtTrKnJw0
9zfBZs2577a0ytCZonMXxFpSTE4e0+GTNN97dno3ueordOqkA9Jr7Bx9FWi4zyiM
0XJLmkFwONMOaKWjN6xtEUh7c5SsvwPSgUbIi/8DhcqeCRxsYsdVZjWxfSmgC4hB
fm+WwvxqxhjklLvy9I+LanaF93k688Penyv8cqnY2Y2lER3tHGZXEtEVWnz0ZWnQ
Ft7NEf8ms5BueX4QCNfd/vX1j6P0dueHvwl9Qv8oLbddgGP2jFPhEA/iZxGn/7Tv
w9rayQPBhPnAZv2bVfYN/LsmpQlivEnWRxK2S2llxAeUo+aPebsS1nRL68JQg4dA
7EFHmX+VBiP2mfXomOb4lJYl/tWIyidlneQ+eqUyY4mim0wF/045FRk7hi/EIqI1
E6jJxG4d3Becxzvtqpd8jj7iA6QkmmnNUdOP8Ktp8bo+9IQd+ogaf3zyNIQdnuSD
td/08yAwNmVLqcV7pvhtgwLtArEp2crekT7MF/CTajMiBRa7JsmyB7rNovYvxbeg
ik/I9cmR2yeu5rAJYQ4w/QpHWYAIFtiGM57rkKodaLW4bptD23KLk7v0zWTwC2WX
pQG+9Yq8kGW6n6BIAUFA5BJ2HaNN2KsS9zIicocFvu2Aab/Rmq6f5ohHH596pEka
7Ck3SmvPd3fJfYgHQCpp
=3cIB
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-for-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
- Move MXS pinctrl registration to poscore_initcall
- Fix up various devm_* managed resources code paths
- Fix one function group in the Nomadik driver
- Update MAINTAINERS
* tag 'pinctrl-fixes-for-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
drivers/pinctrl/pinctrl-nomadik.c: drop devm_kfree of devm_kzalloc'd data
MAINTAINERS: fix a few pinctrl related entries
pinctrl-sirf: remove devm_kfree at error path
pinctrl/nomadik: fix hsi function group list
pinctrl/pinctrl-u300: remove unneeded devm_kfree call
pinctrl: mxs: register driver at postcore_initcall time
These patches fix a couple of issues. First of all a few problems with
ACS on x86 introduced in the last merge window, where ACS did not work
on AMD and a NULL pointer dereference when there ran against SR-IOV
devices.
The patches fallen out of coccinelle checks fix a possible invalid
memory reference and a possible memory leak. The other patches mostly
fix build errors and warnings and a wrong return value.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0b5/
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"These patches fix a couple of issues. First of all a few problems
with ACS on x86 introduced in the last merge window, where ACS did not
work on AMD and a NULL pointer dereference when there ran against
SR-IOV devices.
The patches fallen out of coccinelle checks fix a possible invalid
memory reference and a possible memory leak. The other patches mostly
fix build errors and warnings and a wrong return value."
* tag 'iommu-fixes-v3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix ACS path checking
iommu/intel: Fix ACS path checking
iommu/amd: Fix pci_request_acs() call-place
iommu/exynos: Fix build error
iommu/tegra: smmu: Fix error initial value at domain_init
iommu/tegra: smmu: Cleanup with lesser nest
iommu: Add missing forward declaration in include file
iommu: Include linux/types.h
iommu/intel: add missing free_domain_mem
iommu/tegra: remove invalid reference to list iterator variable
If the last block of the HSA is read, EVSTATE_ALL_STORED is returned
by SCLP. Because of a missing break in the switch statement two trace
entries are written in this case: "all stored" and "part stored".
This patch adds the missing break and also adds a "fall through"
comment to improve the readability.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reported-by: David A Gilbert <DavidAGilbert@uk.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Originally gpio-regulator used the first item of its state list
that matched the given voltage or current range.
Commit 4dbd8f63f0 (regulator: gpio-regulator: Set the smallest voltage/current
in the specified range) changed this, to make the selection independent of
the ordering of the state list.
But selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
Therefore split the previous common selection function into specific
functions for voltage and current regulators.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We may only start to set up the new register values after having
confirmed that the ring is truely off. Otherwise the hw might lose the
newly written register values. This is caught later on in the init
sequence, when we check whether the register writes have stuck.
Cc: stable@vger.kernel.org
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50522
Tested-by: Yang Guang <guang.a.yang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to do left shift (cfg->num + LP8788_ISINK_SCALE_OFFSET) bits for
updating scale configuration.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
As mentioned by Ian Abbott, the pci address passed to ioremap
should be a resource_size_t not an unsigned long. Use a local
variable of that type to hold the pci_resource_start() that is
passed to ioremp().
Set the dev->iobase to a dummy non-zero value so that the "detach"
can use it as a flag to know that comedi_pci_disable() needs to
be called.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned by Ian Abbott, the pci address passed to ioremap
should be a resource_size_t not an unsigned long. Use a local
variable of that type to hold the pci_resource_start() that is
passed to ioremp().
Set the dev->iobase to a dummy non-zero value so that the "detach"
can use it as a flag to know that comedi_pci_disable() needs to
be called.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned by Ian Abbott, the pci address passed to ioremap
should be a resource_size_t not an unsigned long. Use a local
variable of that type to hold the pci_resource_start() that is
passed to ioremp().
Set the dev->iobase to a dummy non-zero value so that the "detach"
can use it as a flag to know that comedi_pci_disable() needs to
be called.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned by Ian Abbott, this driver originally checked
the pci_dev subsystem_device in order to make sure that the
pci_dev was compatible with this driver. The cleanup of the
"find pci device" code removed this check. Add it back.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As mentioned by Ian Abbott, the comedi pci drivers that try to
locate an unused pci device with the pci_is_enabled() test
might actually skip over a perfectly good unused device. This
test is also not consistent with the other comedi pci drivers.
Remove the test from all the comedi pci drivers.
Reported-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we encounter an xHCI host that needs the XHCI_TRUST_TX_LENGTH
quirk, the xHCI driver ends up spewing messages about the quirk into
dmesg every time a short packet occurs. Change the xHCI driver to
rate-limit such warnings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Matthew Hall <mhall@mhcomputing.net>
Reported-by: Gary E. Miller <gem@rellim.com>
Gary reports that with recent kernels, he notices more xHCI driver
warnings:
xhci_hcd 0000:03:00.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
We think his Etron xHCI host controller may have the same buggy behavior
as the Fresco Logic xHCI host. When a short transfer is received, the
host will mark the transfer as successfully completed when it should be
marking it with a short completion.
Fix this by turning on the XHCI_TRUST_TX_LENGTH quirk when the Etron
host is discovered. Note that Gary has revision 1, but if Etron fixes
this bug in future revisions, the quirk will have no effect.
This patch should be backported to kernels as old as 2.6.36, that
contain a backported version of commit
1530bbc627 "xhci: Add new short TX quirk
for Fresco Logic host."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Gary E. Miller <gem@rellim.com>
Cc: stable@vger.kernel.org
The NEC/Renesas 720201 xHCI host controller does not complete its reset
within 250 milliseconds. In fact, it takes about 9 seconds to reset the
host controller, and 1 second for the host to be ready for doorbell
rings. Extend the reset and CNR polling timeout to 10 seconds each.
This patch should be backported to kernels as old as 2.6.31, that
contain the commit 66d4eadd8d "USB: xhci:
BIOS handoff and HW initialization."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Edwin Klein Mentink <e.kleinmentink@zonnet.nl>
Cc: stable@vger.kernel.org
The conversion to voltage tables in
commit a3beb74261
"regulator: ab3100: Use regulator_list_voltage_table()"
missed to add the voltage table to the buck. Fix this and
it works like a charm.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mask used in anatop_get_voltage_sel does not match the mask used in
anatop_set_voltage_sel.
We need to do left shift anatop_reg->vol_bit_shift bits for the correct mask.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As per datasheet, the vin pin for the regulator is named
as vin_sm0, vin_sm1, vin_sm2 for sm0, sm1 and sm2 respectively.
Correcting the names in driver and documentation to match with
datasheet.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below error handling cases:
1. If reading PALMAS_SMPS_CTRL fails, simply returns ret rather than goto
err_unregister_regulator because we have not call regulator_register().
2. If palmas_ldo_init() fails, we need to call regulator_unregister() for the
regulator we just successfully registered in this for loop iteration.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code uses wrong calls palmas_smps_[read|write] in palmas_ldo_init(),
should be palmas_ldo_[read|write] instead.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes below issues when choosing selector:
1. Current code returns negative selector if min_uV < 900000 which is wrong.
For example, it is possible to satisfy the request with selector = 1 if
the requested min_uV is 850000.
2. Current code may select a voltage lower than requested min_uV.
For example, if the requested min_uV is 945000, current code chooses
selector = 1 which is lower than requested min_uV.
DIV_ROUND_UP to avoid this case.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
devm_kfree should not have to be explicitly used.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,d;
@@
x = devm_kzalloc(...)
...
?-devm_kfree(d,x);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the pointers that are allocated with devm_kzalloc will be automatically freed,
at unload time.
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tidy up a small typo in the HSI function group list.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Also properly indent the HB IDs.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some 8086:10c9 NICs have a problem completing the ethtool loopback test.
The result looks like this:
ethtool -t eth1
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 13
Link test (on/offline) 0
A bisect clearly points to commit a95a07445e.
However that seems to only trigger the bug. While adding some printk the
problem disappeared, so this might be a timing issue. After some trial and
error I discovered that adding a small delay just before igb_write_phy_reg()
in igb_integrated_phy_loopback() allows the loopback test to succeed.
I was unable to figure out the root cause so far but I expect it to be
somewhere in the following executing path
igb_integrated_phy_loopback
->igb_write_phy_reg_igp
->igb_write_phy_reg_mdic
->igb_acquire_phy_82575
->igb_acquire_swfw_sync_82575
The problem could only be observed on 8086:10c9 NICs so far and not all
of them show the behaviour. I did not restrict the workaround to this
type of NIC as it should do no harm to other igb NICs.
With the patch below the loopback test succeeded 500 times in a row
using a NIC that would otherwise fail.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
A bus trace shows that while executing e1000e_down, TCTL is cleared except
for the PSP bit. This occurs while in the middle of fetching a TSO packet
since the Tx packet buffer is full at that point. Before the device is
reset, the e1000_watchdog_task starts to run from the middle (it was
apparently pre-empted earlier, although that is not in the trace) and sets
TCTL.EN. At that point, 82571 transmits the corrupted packet, apparently
because TCTL.MULR was cleared in the middle of fetching a packet, which is
forbidden.
Driver should just clear TCTL.EN in e1000_reset_hw_82571 instead of
clearing the entire register, so as not to change any settings in the
middle of fetching a packet.
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
