Add missing ~ to the usage of the mask.
Reported-by: Kevin Benson <Kevin.Benson@zii.aero>
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 5c74c54ce6 ("net: dsa: mv88e6xxx: Split monitor port configuration")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are still experiencing some packet loss with the existing advanced
congestion buffering (ACB) settings with the IMP port configured for
2Gb/sec, so revert to conservative link speeds that do not produce
packet loss until this is resolved.
Fixes: 8f1880cbe8 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Fixes: de34d7084e ("net: dsa: bcm_sf2: Only 7278 supports 2Gb/sec IMP port")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure that the default VID is untagged otherwise the switch
will be sending tagged frames and the results can be problematic. This
is especially true with b53 switches that use VID 0 as their default
VLAN since VID 0 has a special meaning.
Fixes: fea8335317 ("net: dsa: b53: Fix default VLAN ID")
Fixes: 061f6a505a ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for unique interrupt names, after testing on a few
devices, it was assumed 32 characters would be sufficient. This
assumption turned out to be incorrect, ZII RDU2 for example uses a
device base name of mv88e6xxx-30be0000.ethernet-1:0, leaving no space
for post fixes such as -g1-atu-prob and -watchdog. The names then
become identical, defeating the point of the patch.
Increase the length of the string to 64 charactoes.
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Fixes: 3095383a8a ("net: dsa: mv88e6xxx: Unique IRQ name")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 7445 switch clocking profiles do not allow us to run the IMP port at
2Gb/sec in a way that it is reliable and consistent. Make sure that the
setting is only applied to the 7278 family.
Fixes: 8f1880cbe8 ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
b53_configure_vlan() is called by the bcm_sf2 driver upon setup and
indirectly through resume as well. During the initial setup, we are
guaranteed that dev->vlan_enabled is false, so there is no change in
behavior, however during suspend, we may have enabled VLANs before, so we
do want to restore that setting.
Fixes: dad8d7c645 ("net: dsa: b53: Properly account for VLAN filtering")
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SERDES statistics are valid for all members of the 6390 family,
not just the 6390 itself. Add the needed callbacks to all members of
the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the serdes link is set to 2500 using interfce type 2500base-X, lower
link speeds over on the line side should still be supported.
Rate adaptation is done out of band, in our case using AQR PHYs this is
done using flow control.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control is used with 2500Base-X and AQR PHYs to do rate adaptation
between line side 100/1000 links and MAC running at 2.5G.
This is independent of the flow control configuration settled on line
side though AN.
In general, allowing the MAC to handle flow control even if not
negotiated with the link partner should not be a problem, so the patch
just enables it in all cases.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: 8aa9ebccae ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHYs like VSC8234 don't like it when AN restarts on their system side
and they restart line side AN too, going into an endless link up/down loop.
Don't restart PCS AN if link is up already.
Although in theory this feedback loop should be possible with the other
in-band AN modes too, for some reason it was not seen with the VSC8514
QSGMII and AQR412 USXGMII PHYs. So keep this logic only for SGMII where
the problem was found.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least some PHYs (AQR412) don't advertise copper-side link status
during system side AN.
So remove this duplicate assignment to pcs->link and rely on the
previous one for link state: the local indication from the MAC PCS.
Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM531x5 and BCM539x families require that the IMP port be enabled
within the management page and that management mode (SM_SW_FWD_MODE) be
turned on. Once this is done, everything works as expected, including
multicast with standalone DSA devices or bridge devices.
Because such switches are frequencly cascaded with other internal
Broadcom switches on which we want to enable Broadcom tags, update
b53_can_enable_brcm_tags() to check the kind of DSA master tagging
protocol being used, if it is one of the two supported Broadcom tagging
protocols, force DSA_TAG_PROTO_NONE.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique interrupt name for the VTU and ATU,
based on the device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique g2 interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique watchdog interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique SERDES interrupt name, based on the
device name and the port the SERDES is for. For example:
95: 3 mv88e6xxx-g2 9 Edge mv88e6xxx-0.2:00-serdes-9
96: 0 mv88e6xxx-g2 10 Edge mv88e6xxx-0.2:00-serdes-10
The 0.2:00 indicates the switch and -9 indicates port 9.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dynamically generate a unique switch interrupt name, based on the
device name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family uses an extended register to set the port connected to
the CPU. The lower 5 bits indicate the port, the upper three bits are
the priority of the frames as they pass through the switch, what
egress queue they should use, etc. Since frames being set to the CPU
are typically management frames, BPDU, IGMP, ARP, etc set the priority
to 7, the reset default, and the highest.
Fixes: 33641994a6 ("net: dsa: mv88e6xxx: Monitor and Management tables")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Layerscape SoCs traditionally expose the SerDes configuration/status for
Ethernet protocols (PCS for SGMII/USXGMII/10GBase-R etc etc) in a register
format that is compatible with clause 22 or clause 45 (depending on
SerDes protocol). Each MAC has its own internal MDIO bus on which there
is one or more of these PCS's, responding to commands at a configurable
PHY address. The per-port internal MDIO bus (which is just for PCSs) is
totally separate and has nothing to do with the dedicated external MDIO
controller (which is just for PHYs), but the register map for the MDIO
controller is the same.
The VSC9959 (Felix) switch instantiated in the LS1028A is integrated
in hardware with the ENETC PCS of its DSA master, and reuses its MDIO
controller driver, so Felix has been made to depend on it in Kconfig.
+------------------------------------------------------------------------+
| +--------+ GMII (typically disabled via RCW) |
| ENETC PCI | ENETC |--------------------------+ |
| Root Complex | port 3 |-----------------------+ | |
| Integrated +--------+ | | |
| Endpoint | | |
| +--------+ 2.5G GMII | | |
| | ENETC |--------------+ | | |
| | port 2 |-----------+ | | | |
| +--------+ | | | | |
| +--------+ +--------+ |
| | Felix | | Felix | |
| | port 4 | | port 5 | |
| +--------+ +--------+ |
| |
| +--------+ +--------+ +--------+ +--------+ +--------+ +--------+ |
| | ENETC | | ENETC | | Felix | | Felix | | Felix | | Felix | |
| | port 0 | | port 1 | | port 0 | | port 1 | | port 2 | | port 3 | |
+------------------------------------------------------------------------+
| |||| SerDes | |||| |||| |||| |||| |
| +--------+block | +--------------------------------------------+ |
| | ENETC | | | ENETC port 2 internal MDIO bus | |
| | port 0 | | | PCS PCS PCS PCS | |
| | PCS | | | 0 1 2 3 | |
+-----------------|------------------------------------------------------+
v v v v v v
SGMII/ RGMII QSGMII/QSXGMII/4xSGMII/4x1000Base-X/4x2500Base-X
USXGMII/ (bypasses
1000Base-X/ SerDes)
2500Base-X
In the LS1028A SoC described above, the VSC9959 Felix switch is PF5 of
the ENETC root complex, and has 2 BARs:
- BAR 4: the switch's effective registers
- BAR 0: the MDIO controller register map lended from ENETC port 2
(PF2), for accessing its associated PCS's.
This explanation is necessary because the patch does some renaming
"pci_bar" -> "switch_pci_bar" for clarity, which would otherwise appear
a bit obtuse.
The fact that the internal MDIO bus is "borrowed" is relevant because
the register map is found in PF5 (the switch) but it triggers an access
fault if PF2 (the ENETC DSA master) is not enabled. This is not treated
in any way (and I don't think it can be treated).
All of this is so SoC-specific, that it was contained as much as
possible in the platform-integration file felix_vsc9959.c.
We need to parse and pre-validate the device tree because of 2 reasons:
- The PHY mode (SerDes protocol) cannot change at runtime due to SoC
design.
- There is a circular dependency in that we need to know what clause the
PCS speaks in order to find it on the internal MDIO bus. But the
clause of the PCS depends on what phy-mode it is configured for.
The goal of this patch is to make steps towards removing the bootloader
dependency for SGMII PCS pre-configuration, as well as to add support
for monitoring the in-band SGMII AN between the PCS and the system-side
link partner (PHY or other MAC).
In practice the bootloader dependency is not completely removed. U-Boot
pre-programs the PHY address at which each PCS can be found on the
internal MDIO bus (MDEV_PORT). This is needed because the PCS of each
port has the same out-of-reset PHY address of zero. The SerDes register
for changing MDEV_PORT is pretty deep in the SoC (outside the addresses
of the ENETC PCI BARs) and therefore inaccessible to us from here.
Felix VSC9959 and Ocelot VSC7514 are integrated very differently in
their respective SoCs, and for that reason Felix does not use the Ocelot
core library for PHYLINK. On one hand we don't want to impose the
fixed phy-mode limitation to Ocelot, and on the other hand Felix doesn't
need to force the MAC link speed the way Ocelot does, since the MAC is
connected to the PCS through a fixed GMII, and the PCS is the one who
does the rate adaptation at lower link speeds, which the MAC does not
even need to know about. In fact changing the GMII speed for Felix
irrecoverably breaks transmission through that port until a reset.
The pair with ENETC port 3 and Felix port 5 is optional and doesn't
support tagging. When we enable it, swp5 is a regular slave port, albeit
an internal one. The trouble is that it doesn't work, and that is
because the DSA PHYLIB adaptation layer doesn't treat fixed-link slave
ports. So that is yet another reason for wanting to convert Felix to the
native PHYLINK API.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 3 things that are wrong with the DSA deferred xmit mechanism:
1. Its introduction has made the DSA hotpath ever so slightly more
inefficient for everybody, since DSA_SKB_CB(skb)->deferred_xmit needs
to be initialized to false for every transmitted frame, in order to
figure out whether the driver requested deferral or not (a very rare
occasion, rare even for the only driver that does use this mechanism:
sja1105). That was necessary to avoid kfree_skb from freeing the skb.
2. Because L2 PTP is a link-local protocol like STP, it requires
management routes and deferred xmit with this switch. But as opposed
to STP, the deferred work mechanism needs to schedule the packet
rather quickly for the TX timstamp to be collected in time and sent
to user space. But there is no provision for controlling the
scheduling priority of this deferred xmit workqueue. Too bad this is
a rather specific requirement for a feature that nobody else uses
(more below).
3. Perhaps most importantly, it makes the DSA core adhere a bit too
much to the NXP company-wide policy "Innovate Where It Doesn't
Matter". The sja1105 is probably the only DSA switch that requires
some frames sent from the CPU to be routed to the slave port via an
out-of-band configuration (register write) rather than in-band (DSA
tag). And there are indeed very good reasons to not want to do that:
if that out-of-band register is at the other end of a slow bus such
as SPI, then you limit that Ethernet flow's throughput to effectively
the throughput of the SPI bus. So hardware vendors should definitely
not be encouraged to design this way. We do _not_ want more
widespread use of this mechanism.
Luckily we have a solution for each of the 3 issues:
For 1, we can just remove that variable in the skb->cb and counteract
the effect of kfree_skb with skb_get, much to the same effect. The
advantage, of course, being that anybody who doesn't use deferred xmit
doesn't need to do any extra operation in the hotpath.
For 2, we can create a kernel thread for each port's deferred xmit work.
If the user switch ports are named swp0, swp1, swp2, the kernel threads
will be named swp0_xmit, swp1_xmit, swp2_xmit (there appears to be a 15
character length limit on kernel thread names). With this, the user can
change the scheduling priority with chrt $(pidof swp2_xmit).
For 3, we can actually move the entire implementation to the sja1105
driver.
So this patch deletes the generic implementation from the DSA core and
adds a new one, more adequate to the requirements of PTP TX
timestamping, in sja1105_main.c.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I finally found out how the 4 management route slots are supposed to
be used, but.. it's not worth it.
The description from the comment I've just deleted in this commit is
still true: when more than 1 management slot is active at the same time,
the switch will match frames incoming [from the CPU port] on the lowest
numbered management slot that matches the frame's DMAC.
My issue was that one was not supposed to statically assign each port a
slot. Yes, there are 4 slots and also 4 non-CPU ports, but that is a
mere coincidence.
Instead, the switch can be used like this: every management frame gets a
slot at the right of the most recently assigned slot:
Send mgmt frame 1 through S0: S0 x x x
Send mgmt frame 2 through S1: S0 S1 x x
Send mgmt frame 3 through S2: S0 S1 S2 x
Send mgmt frame 4 through S3: S0 S1 S2 S3
The difference compared to the old usage is that the transmission of
frames 1-4 doesn't need to wait until the completion of the management
route. It is safe to use a slot to the right of the most recently used
one, because by protocol nobody will program a slot to your left and
"steal" your route towards the correct egress port.
So there is a potential throughput benefit here.
But mgmt frame 5 has no more free slot to use, so it has to wait until
_all_ of S0, S1, S2, S3 are full, in order to use S0 again.
And that's actually exactly the problem: I was looking for something
that would bring more predictable transmission latency, but this is
exactly the opposite: 3 out of 4 frames would be transmitted quicker,
but the 4th would draw the short straw and have a worse worst-case
latency than before.
Useless.
Things are made even worse by PTP TX timestamping, which is something I
won't go deeply into here. Suffice to say that the fact there is a
driver-level lock on the SPI bus offsets any potential throughput gains
that parallelism might bring.
So there's no going back to the multi-slot scheme, remove the
"mgmt_slot" variable from sja1105_port and the dummy static assignment
made at probe time.
While passing by, also remove the assignment to casc_port altogether.
Don't pretend that we support cascaded setups.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no build time dependency on CONFIG_OF, but we do need to make
sure we gate the initialization of the gpio_chip::of_node member with a
proper check on CONFIG_OF_GPIO. This enables the driver to build on
platforms that do not have CONFIG_OF enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling PTP timestamping, don't reset the switch with the new
static config until all existing PTP frames have been timestamped on the
RX path or dropped. There's nothing we can do with these afterwards.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And move the queue of skb's waiting for RX timestamps into the ptp_data
structure, since it isn't needed if PTP is not compiled.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.
Fixes: 86db36a347 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:
[ 37.691971] sja1105 spi0.1: An operation returned -22
The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.
Fixes: 41603d78b3 ("net: dsa: sja1105: Make the PTP command read-write")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.
As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.
Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.
Fixes: 47ed985e97 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If packet checker is enabled in the serdes, then Rx counter registers
start working, and no side effects have been detected.
This patch enables packet checker automatically when powering serdes on,
and exposes Rx counter registers via ethtool statistics interface.
Code partially basded by older attempt by Andrew Lunn.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set variable 'mbus' static
since new value always be assigned before use it.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP fragment is specified through user-defined field as the first
bit of the first user-defined word. We were previously trying to extract
it from the user-defined mask which could not possibly work. The ip_frag
is also supposed to be a boolean, if we do not cast it as such, we risk
overwriting the next fields in CFP_DATA(6) which would render the rule
inoperative.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide basic support for Atheros AR9331 built-in switch. So far it
works as port multiplexer without any hardware offloading support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Selecting MSCC_OCELOT_SWITCH is not possible when NET_VENDOR_MICROSEMI
is disabled:
WARNING: unmet direct dependencies detected for MSCC_OCELOT_SWITCH
Depends on [n]: NETDEVICES [=y] && ETHERNET [=n] && NET_VENDOR_MICROSEMI [=n] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y]
Selected by [m]:
- NET_DSA_MSCC_FELIX [=m] && NETDEVICES [=y] && HAVE_NET_DSA [=y] && NET_DSA [=y] && PCI [=y]
Add a Kconfig dependency on NET_VENDOR_MICROSEMI, which also implies
CONFIG_NETDEVICES.
Depending on a vendor config violates menuconfig locality for the DSA
driver, but is the smallest compromise since all other solutions are
much more complicated (see [0]).
https://www.spinics.net/lists/netdev/msg618808.html
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were several issues with 53568438e3 ("net: dsa: b53: Add support for port_egress_floods callback") that resulted in breaking connectivity for standalone ports:
- both user and CPU ports must allow unicast and multicast forwarding by
default otherwise this just flat out breaks connectivity for
standalone DSA ports
- IP multicast is treated similarly as multicast, but has separate
control registers
- the UC, MC and IPMC lookup failure register offsets were wrong, and
instead used bit values that are meaningful for the
B53_IP_MULTICAST_CTRL register
Fixes: 53568438e3 ("net: dsa: b53: Add support for port_egress_floods callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was using configuration of port 0 in devicetree for all ports.
In case CPU port was not 0, the delay settings was ignored. This resulted not
working communication between CPU and the switch.
Fixes: f5b8631c29 ("net: dsa: sja1105: Error out if RGMII delays are requested in DT")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following sparse warnings:
drivers/net/dsa/ocelot/felix.c:351:6: warning: symbol 'felix_txtstamp' was not declared. Should it be static?
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to reuse ocelot functions as possible to enable PTP
clock and to support hardware timestamping on Felix.
On TX path, timestamping works on packet which requires timestamp.
The injection header will be configured accordingly, and skb clone
requires timestamp will be added into a list. The TX timestamp
is final handled in threaded interrupt handler when PTP timestamp
FIFO is ready.
On RX path, timestamping is always working. The RX timestamp could
be got from extraction header.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to define PTP registers for felix_vsc9959.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch
and the ENETC:
- eno2 <-> swp4, at 2.5G
- eno3 <-> swp5, at 1G
Only one of the above Ethernet port pairs can act as a DSA link for
tagging.
When adding initial support for the driver, it was tested only on the 1G
eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially
(which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't
support fixed-link speeds higher than 1G).
After making PHYLINK work, it appears that swp4 still can't act as CPU
port. So it looks like ocelot_set_cpu_port was being called for swp4,
but then it was called again for swp5, overwriting the CPU port assigned
in the DT.
It appears that when you call dsa_upstream_port for a port that is not
defined in the device tree (such as swp5 when using swp4 as CPU port),
its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu,
and this trips up the following condition in dsa_upstream_port:
if (!cpu_dp)
return port;
So the moral of the story is: don't call dsa_upstream_port for a port
that is not defined in the device tree, and therefore its dsa_port
structure is not completely initialized (ds->num_ports is still 6).
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
