VFs attached to PFs other than AF can not communicate with AF
directly. Instead they are supposed to first send message to
the PF they are residing on and PF forwards it to the AF.
Responses to messages are handled in the reverse order.
On the other hand if VFs are on AF (PF0) itself then direct mailbox
communication is possible since there's no other PF in the way.
This patch addresses this particular case and adds support for
handling it.
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Marko Kallio <mkallio@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon receiving FLR IRQ for a RVU PF, teardown or cleanup
resources held by that PF_FUNC. This patch cleans up,
NIX LF
- Stop ingress/egress traffic
- Disable NPC MCAM entries being used.
- Free Tx scheduler queues
- Disable RQ/SQ/CQ HW contexts
NPA LF
- Disable Pool/Aura HW contexts
In future teardown of SSO/SSOW/TIM/CPT will be added.
Also added a mailbox message for a RVU PF to request
AF, to perform FLR for a RVU VF under it.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RVU admin function (AF) has all the priviliges to cleanup
HW state when VFIO triggers a PCIe function level reset (FLR)
due to either reset or a VM crash. FLR for RVU PF1-PFn will
trigger an IRQ to AF.
This patch enables all RVU PF's FLR interrupts and registers a
handler. Upon receiving an interrupt, a workqueue is scheduled
to cleanup all hardware blocks being used by the PF which
received the FLR.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While mapping a NIX LF to a NPA LF attached PF_FUNC or
SSO LF attached PF_FUNC, verify if PF_FUNC is valid and
if that PF_FUNC has a LF of that block attached to it or not.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This works by shadowing existing UCAST MCAM entry
with a new one additionally matching either NPC_LT_LB_CTAG
or NPC_LT_LB_STAG. For this to fully work one needs to
send properly configured NIX_VTAG_CFG message afterwards i.e with
strip and capture enabled and type set to 0.
On receiving tagged packet NIX will remove outer VLAN and capture
TCI in NIX_RX_PARSE_S.
Also simplified RX Vtag configuration flow
With this setting STRIP/CAPTURE VTAG actions separately would be
possible. Following combinations are possible: STRIP,
STRIP and CAPTURE, CAPTURE or nothing (0 disables respective actions).
Signed-off-by: Tomasz Duszynski <tduszynski@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a PF/VF with a NIXLF attached has default/reserved MCAM entries
for receiving Ucast/Bcast/Promisc traffic. Ideally traffic should be
forwarded to NIXLF only after it's contexts are initialized. This
patch keeps these default entries disabled and adds mbox messages
for a PF/VF to enable these once NPA/NIXLF initialization is done.
Likewise while PF/VF is being teared down, it can send the disable
mailbox message to stop receiving traffic.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added basic default MKEX profile. This profile tells
hardware what data to extract from packet and where to
place it (bit offset) in final KEY generated for the
parsed packet. Based on the bit placement of the packet
data, MCAM entries have to programmed for matching.
Also added a msg to retrieve this MKEX profile from PF/VF
which inturn can process it to determine how MCAM entry
has to be populated.
Signed-off-by: Santosh Shukla <sshukla@marvell.com>
Signed-off-by: Yuri Tolstov <ytolstov@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new mailbox message is added to support allocating a MCAM entry
along with a counter and configuring it in one go. This reduces
the amount of mailbox communication involved in installing a new
MCAM rule.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alloc memory to save MCAM 'entry to counter' mapping and since
multiple entries can map to same counter, added counter's reference
count tracking.
Do 'entry to counter' mapping when a entry is being installed
and mbox msg sender requested to configure a counter as well.
Mapping is removed when a entry or counter is being freed or
a explicit mbox msg is received to unmap them.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NPC HW has counters which can be mapped to MCAM
entries to gather entry match statistics. This
patch adds support to allocate, free, clear and retrieve
stats of NPC MCAM counters. New mailbox messages have
been added for this. Similar to MCAM entries both
contiguous and non-contiguous counter allocation is
supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a RVU PF/VF to enable, disable, configure
and shuffle MCAM entries via mbox commands. This patch adds
mailbox message formats and handling of these commands.
As of now otherthan validating MCAM entry index, info like
channel number e.t.c in MCAM config data sent by PF/VF are
not validated.
Also a max of 64 MCAM entries can be shuffled with a single
mbox command.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds NPC MCAM entry management and support for
allocating and freeing them via mailbox. Both contiguous and
non-contiguous allocations are supported. Incase of contiguous,
if request cannot be met then max contiguous number of available
entries are allocated.
High or low priority index allocation w.r.t a reference MCAM index
is also supported.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mailbox message handling is done in a workqueue context scheduled
from interrupt handler. So resource locks does not need to be a spinlock.
Therefore relax them into a mutex so that later on we may use them
in routines that might sleep.
Signed-off-by: Stanislaw Kardach <skardach@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds reading HW limits like number of Rx/Tx stats,
number of queue IRQs supported per NIX LF from AF registers
and sync them to PF/VF.
Signed-off-by: Kiran Kumar <kirankumark@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for RVU PF/VFs to modify min/max
packet lengths allowed by HW. For VFs on PF0, settings will
be automatically applied on LBK link. RX link's min/maxlen
is configured to min/max of PF and it's all VFs. On the TX side
if requested all SMQs attached to the requesting NIXLF will be
updated with new min/max lengths.
Also updates transmit credits for Tx links based on new maxlen.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts all mailbox message handler API
names to lowercase.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the upper 12 bits are used for chip identification, this helps
to reduce the size of array mac_info.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8168_oob_notify is used in rtl8168dp_driver_start and
rtl8168dp_driver_stop only, so we can rename it to r8168dp_oob_notify.
The same applies to condition rtl_ocp_read_cond which can be renamed
to rtl_dp_ocp_read_cond. This allows to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel can't be built any longer with this ancient GCC version.
Eventually it becomes clear what this statement actually does.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The compiler takes care of alignment and padding, I see no need to
bother him with manual hints.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ones who want to know can easily identify whether chip is PCI or
PCIe based on the chip name. I doubt there's any benefit in this
message, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The syslog message printed on driver load allows to easily identify
the mac version number (based on chip name and XID). So we don't
need this extra debug message which is wrong anyway because e.g.
RTL_GIGA_MAC_VER_01 has value 0.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using macro PCI_VDEVICE helps to simplify the PCI ID table.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the "slow event" handler was removed, therefore the member
name isn't appropriate any longer. In addition store the full mask,
including the RTL_EVENT_NAPI interrupt source bits.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting PCSTimeout interrupt source was copied from the vendor driver
which uses the chip programmable timer interrupt. The mainline driver
doesn't use this timer interrupt.
SYSErr indicates a PCI error and isn't defined on the PCIe models.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using dev_get_drvdata directly is simpler here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent changes to the interrupt handler rtl_irq_enable and
rtl_irq_enable_all can be merged.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When writing packets to a descriptor associated with a combined queue, the
packets should end up on that queue.
Before this change all packets written to any descriptor associated with a
tap interface end up on rx-0, even when the descriptor is associated with a
different queue.
The rx traffic can be generated by either of the following.
1. a simple tap program which spins up multiple queues and writes packets
to each of the file descriptors
2. tx from a qemu vm with a tap multiqueue netdev
The queue for rx traffic can be observed by either of the following (done
on the hypervisor in the qemu case).
1. a simple netmap program which opens and reads from per-queue
descriptors
2. configuring RPS and doing per-cpu captures with rxtxcpu
Alternatively, if you printk() the return value of skb_get_rx_queue() just
before each instance of netif_receive_skb() in tun.c, you will get 65535
for every skb.
Calling skb_record_rx_queue() to set the rx queue to the queue_index fixes
the association between descriptor and rx queue.
Signed-off-by: Matthew Cover <matthew.cover@stackpath.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose packets discard counters via ethtool to help with debugging.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to cook skbs in the same way than Ethernet drivers,
it is probably better to not use GFP_KERNEL, but rather
use the GFP_ATOMIC and PFMEMALLOC mechanisms provided by
netdev_alloc_frag().
This would allow to use tun driver even in memory stress
situations, especially if swap is used over this tun channel.
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petar Penkov <peterpenkov96@gmail.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101GR is a 32-pin QFN package variant of the IP101G/IP101GA
Ethernet PHY. Due to it's limited amount of pins the RXER (receive
error) and INTR32 (interrupt) functions share pin 21.
By default the PHY is configured to output the "receive error" status on
pin 21. Depending on the board layout and requirements we may want to
re-configure the PHY to output the interrupt signal there.
The mode of pin 21 can be configured in the "Digital I/O Specific
Control Register" (register 29), bit 2:
- 0 = RXER function
- 1 = INTR(32) function
Depending on the devicetree configuration we will now:
- change the mode to either ther RXER or INTR32 function
- keep the SEL_INTR32 value set by the bootloader (default) if no
configuration is provided (to ensure that we're not breaking existing
boards)
- error out if conflicting configuration is given (RXER and INTR32 mode
are enabled at the same time)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP101A_G_IRQ_CONF_STATUS register has bits to detect which
interrupts have fired. Implement the .did_interrupt callback to let the
PHY core know whether the interrupt was for this specific PHY.
This is useful for debugging interrupt problems with 32-pin IP101GR PHYs
where the interrupt line is shared with the RX_ERR (receive error
status) signal. The default values are:
- RX_ERR is enabled by default (LOW means that there is no receive
error)
- the PHY's interrupt line is configured "active low" by default
Without any additional changes there is a flood of interrupts if the
RX_ERR/INTR32 signal is configured in RX_ERR mode (which is the
default). Having a did_interrupt ensures that the PHY core returns
IRQ_NONE instead of endlessly triggering the PHY state machine.
Additionally the kernel will report this after a while:
irq 28: nobody cared (try booting with the "irqpoll" option)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The datasheet uses the name "All Mask" for this bit. Change the name of
our #define to be consistent with the datasheet. While here also replace
the tab between the #define and IP101A_G_IRQ_ALL_MASK with a space.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the code consistent by using the BIT() macro instead of
manual bit-shifting for some of the fields. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simply moves ip101a_g_config_init right above
ip101a_g_config_intr so all functions for the ICPlus IP101A/G PHYs are
grouped together.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will try to determine the mac address via the devicetree,
or via an architecture-specific method (e.g. a PROM on SPARC).
The SPARC-specific code in this driver (#ifdef SPARC) did exactly this,
and is therefore removed.
Note that you can now specify the tg3 mac address via the devicetree,
on any platform, not just SPARC:
Devicetree example:
(see Documentation/devicetree/bindings/pci/pci.txt)
&pcie {
host@0 {
#address-cells = <3>;
#size-cells = <2>;
reg = <0 0 0 0 0>;
bcm5778: bcm5778@0 {
reg = <0 0 0 0 0>;
mac-address = [CA 11 AB 1E 10 01];
};
};
};
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an error occurs during suspension of the driver the driver should
restore the hardware configuration and return an error to force the
system to resume.
Fixes: 0db55093b5 ("net: bcmgenet: return correct value 'ret' from bcmgenet_power_down")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit switches the order of bcmgenet_suspend and bcmgenet_resume
in the file to prevent the need for a forward declaration in the next
commit and to make the review of that commit easier.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
drivers/net/geneve.c:428:29: error: suggest braces around initialization
of subobject [-Werror,-Wmissing-braces]
struct in6_addr addr6 = { 0 };
^
{}
Rather than trying to appease the various compilers that support the
kernel, use memset, which is unambiguous.
Fixes: a07966447f ("geneve: ICMP error lookup handler")
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netdev is down in enet module, and it is before
mtu range checking in hclge module, which may be cause
netdev being down unnecessarily.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds mtu setting support for vf, currently
vf and pf share the same hardware mtu setting. Mtu set
by vf must be less than or equal to pf' mtu, and mtu
set by pf must be greater than or equal to vf' mtu.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way for pf to know if a vf device is
alive or not, so PF does not know which vf to notify when
reset happens, or which vf's mtu is invalid when vf and pf
share the same hardware mtu setting.
This patch adds vport alive state checking support, in order
to support the above scenario.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors mac mtu setting related functions,
normalizes the use of mps and mtu.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds supports for two vlan header when setting mtu.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove directly accessing device_node.type pointer and use the accessors
instead. This will eventually allow removing the type pointer.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a netdev_err message. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until commit 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod
functions where possible"), the _cansleep variants of the gpio_ API was
used. After that commit and the change to gpiod_ API, the _cansleep()
was dropped. This then results in WARN_ON() when used with GPIO
devices which do sleep. Add back the _cansleep() to avoid this.
Fixes: 7e5fbd1e07 ("net: mdio-gpio: Convert to use gpiod functions where possible")
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SGE Host Page Size has nothing to do with the actual
Host Page Size. It's the SGE's BAR2 Doorbell/GTS Page Size
for interpreting the SGE Ingress/Egress Queue per Page values.
Firmware reads all of these things and makes all the
subsequent changes necessary. The Host Driver uses the SGE
Host Page Size in order to properly calculate BAR2 Offsets.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
